Comparison between the dispersion curves calculated in complex frequency and the minima of the reflection coefficients for an embedded layer

Analytical solutions of Lamb functions for symmetric and antisymmetric elastodynamic modes propagating within a solid layer embedded in an infinite medium are presented. Alternative theoretical analyses of such modes are performed, first in terms of the usual approach of harmonic heterogeneous plane waves (real frequency and complex slowness) and then in terms of transient homogeneous plane waves (complex frequency and real slowness). An example structure of a 0.1-mm-thick "alpha case" (an oxygen-rich phase of titanium that is relatively stiff) plate embedded in titanium is used for the study. A large difference between the usual dispersion curves calculated in real frequency and complex slowness and those calculated in complex frequency and real slowness is shown. Thus the choice between a spatial and a temporal parameter to describe the imaginary part of the guided waves is shown to be significant. The minima and the zeros of the longitudinal and shear plane-wave reflection coefficients are calculated and are compared with the dispersion curves. It is found that they do not match with the dispersion curves for complex slowness, but they do agree quite well with the dispersion curves for complex frequency. This implies that the complex frequency approach is better suited for the comparison of the modal properties with near-field reflection measurements.     

一种评价固体板材表面性质的非线性超声兰姆波方法

在基频与二倍频兰姆波相速度匹配但群速度失配的条件下, 通过选择适当的兰姆波二次谐波时域信号的测量起止时间, 可完全扣除换能器对二次谐波积分振幅测量所带来的影响。本文提出采用兰姆波二次谐波的积分振幅作为评价参量, 以实现对板材表面性质的准确评价。当板材表面性质发生改变时, 原本在理想表面条件下成立的基频与二倍频兰姆波相速度匹配的条件不再严格满足, 这将显著地影响到兰姆波的二次谐波发生效率, 相应的二次谐波积分振幅随表面性质的改变也将发生非常敏感的单调变化。实验结果表明,利用扣除换能器影响之后所测得的兰姆波二次谐波的积分振幅,可对板材表面性质的变化情况进行准确评价。     

基于频散补偿和分数阶微分的多模式兰姆波分离

由于兰姆波的多模和频散特性,实际检测时在同一激发频率下存在多种模式的混合信号,而各模式信号有不同的频散特性,使得在时频混叠的情况下兰姆波的检测变得十分复杂.本文在频散补偿的基础上,通过时延函数建模,依靠不同模式频散趋势的差异性,将时频混叠信号的分离问题转化为部分模式混叠信号的分离问题.基于分数阶微分的理论,用信号幅值谱分数阶微分极大值和对应频率分别与微分阶次拟合多项式实现特征参数的提取并依靠特征参数重建幅值谱.结合相位谱重构时域信号以实现部分混叠信号中频散补偿后的模式的分离.最后恢复频散获得分离后的兰姆波信号.仿真和实验结果表明,本文方法不仅可以实现时频混叠多模式兰姆波信号的分离,更能保证分离精度,有助于复杂多模式频散信号的分离与处理的进一步研究.     

超声Lamb波二次谐波发生效率分析与模式选择

在导波模式展开分析方法的基础上,提出激发效率参量来定量表征超声Lamb波积累二次谐波的发生效率。以P92钢板为例,理论计算得到了与频散曲线对应的理论激发效率参量分布图谱,从图谱中选择理论激发效率参量大小不同的两种基频Lamb波模式:纵波型S1模式和交点型A2/S2模式,分别测量这两种基频Lamb波模式在钢板中传播时产生的二次谐波信号。理论计算和实验测量结果表明,这两种基频Lamb波模式的理论和实验激发效率参量的比值基本一致,且激发效率参量较大的纵波型S1模式能激发出效率更高的二次谐波信号。研究结果表明激发效率参量可以有效的用于Lamb波二次谐波发生效率的表征及模式选择。      

Time reversal technique for health monitoring of metallic structure using Lamb waves

Time reversal active sensing using Lamb waves is investigated for health monitoring of a metallic structure. Experiments were conducted on an aluminum plate to study the time reversal behavior of A₀ and S₀ Lamb wave modes under narrow band and broad band pulse excitation. Damage in the form of a notch was introduced in the plate to study the changes in the characteristics of the time reversed Lamb wave modes experimentally. Time–frequency analysis of the time reversed signal was carried out to extract the damage information. A measure of damage based on wavelet transform was derived to quantify the hidden damage information in the time reversed signal. It has been shown that time reversal can be used to achieve temporal recompression of Lamb waves under broadband signal excitation. Further, the broad band excitation can also improve the resolution of the technique in detecting closely located defects. This is demonstrated by picking up the reflection of waves from the edge of the plate, from a defect close to the edge of the plate and from defects located near to each other. This study shows the effectiveness of Lamb wave time reversal for temporal recompression of dispersive Lamb waves for damage detection in health monitoring applications.     

Piezoelectric transducer parameter selection for exciting a single mode from multiple modes of Lamb waves

Excitation and propagation of Lamb waves by using rectangular and circular piezoelectric transducers surface-bonded to an isotropic plate are investigated in this work. Analytical stain wave solutions are derived for the two transducer shapes, giving the responses of these transducers in Lamb wave fields. The analytical study is supported by a numerical simulation using the finite element method. Symmetric and antisymmetric components in the wave propagation responses are inspected in detail with respect to test parameters such as the transducer geometry, the length and the excitation frequency. By placing only one piezoelectric transducer on the top or the bottom surface of the plate and weakening the strength of one mode while enhancing the strength of the other modes to find the centre frequency, with which the peak wave amplitude ratio between the S0 and A0 modes is maximum, a single mode excitation from the multiple modes of the Lamb waves can be achieved approximately. Experimental data are presented to show the validity of the analyses. The results are used to optimize the Lamb wave detection system.     

采用单个压电传感器的单模式兰姆波激发频率的选择

考虑了压电传感器(PZT)与板之间的耦合作用,从理论上研究了单个压电传感器激发时产生单模式兰姆波的频率调节方法,实验给出了模式选择在兰姆波结构健康监测中的应用. 在板材、板厚以及PZT尺寸一定的情况下,从理论上能够预测到作为频率函数的各兰姆波模式的幅值变化. 根据某特定兰姆波模式的幅值最大而其他模式幅值相对最小时所对应的频率,即可识别出该兰姆波模式优化的激发频率. 数值仿真验证了理论的有效性以及单模式兰姆波选择的可能性. 在不同的激发频率下,分别激发了优化的A0 模式,优化的S0模式以及共存的A0和S0模 关键词： 兰姆波 压电传感器 激发频率 结构健康监测     

基于群速度失配的超声兰姆波二次谐波的时域测量方法

考虑到发射和接收换能器对超声兰姆波时域二次谐波信号所带来的不可避免的影响,提出一种基于基频与二倍频兰姆波群速度失配的超声兰姆波二次谐波的时域测量方法。当基频与二倍频超声兰姆波的相速度匹配而群速度失配时,在超声兰姆波传播过程中所发生的二次谐波信号,在时域上可与源于斜劈换能器的二次谐波信号相分离。采用仅源自于基频兰姆波的时域二次谐波的积分振幅,定量描述兰姆波二次谐波的发生效率。以铝板中传播的兰姆波为例,给出了时域二次谐波的具体测量过程。本文提出的测量方法放宽了超声兰姆波二次谐波的测量条件,且扣除了换能器对二次谐波信号所带来的影响,所测得的二次谐波信号完全来自于基频兰姆波时域信号的二次谐波发生效应。      

Time-frequency analysis of the dispersion of Lamb modes.

Accurate knowledge of the velocity dispersion of Lamb modes is important for ultrasonic nondestructive evaluation methods used in detecting and locating flaws in thin plates and in determining their elastic stiffness coefficients. Lamb mode dispersion is also important in the acoustic emission technique for accurately triangulating the location of emissions in thin plates. In this research, the ability to characterize Lamb mode dispersion through a time-frequency analysis (the pseudo-Wigner-Ville distribution) was demonstrated. A major advantage of time-frequency methods is the ability to analyze acoustic signals containing multiple propagation modes, which overlap and superimpose in the time domain signal. By combining time-frequency analysis with a broadband acoustic excitation source, the dispersion of multiple Lamb modes over a wide frequency range can be determined from as little as a single measurement. In addition, the technique provides a direct measurement of the group velocity dispersion. The technique was first demonstrated in the analysis of a simulated waveform in an aluminum plate in which the Lamb mode dispersion was well known. Portions of the dispersion curves of the A0, A1, S0, and S2 Lamb modes were obtained from this one waveform. The technique was also applied for the analysis of experimental waveforms from a unidirectional graphite/epoxy composite plate. Measurements were made both along and perpendicular to the fiber direction. In this case, the signals contained only the lowest order symmetric and antisymmetric modes. A least squares fit of the results from several source to detector distances was used. Theoretical dispersion curves were calculated and are shown to be in good agreement with experimental results.     

Feasibility of bone assessment with leaky Lamb waves in bone phantoms and a bovine tibia

In this study, the effect of cortical thickness variation on the propagation of leaky Lamb waves is investigated by using an axial transmission technique commonly used to characterize long bones. Three Lucite plates with thicknesses of 1, 3, and 5 mm as bone phantoms and one bovine tibia with a cortical thickness of 2 mm were used at various low frequencies. Experimental measurements in bone phantoms show that the peak frequency and amplitude of excited Lamb modes strongly depend on the thickness of the Lucite plate. In the bovine tibia, the S0 and A0 Lamb modes are consistently observed in the frequency-thickness region from 0.2 to 1.0 MHz mm, and can be effectively launched at a frequency of 200 kHz, suggesting 200 kHz to be the optimal signal frequency for in vivo clinical applications. It can be also seen that both modes are affected by the frequency-thickness product, but the effect is greater for the A0 mode. Hence, the A0 Lamb mode seems more sensitive to cortical thickness change due to aging and osteoporosis. This study suggests that the use of leaky Lamb waves is feasible for ultrasonic bone assessment.     

Lamb waves beam deviation due to small inclination of the test structure in air-coupled ultrasonic NDT

In Lamb waves inspection, an air-coupled transmitter transducer is oriented at a specific angle such that it generates a pure Lamb mode which propagates along the structure and interacts with any existing defects. For this inspection system, amplitude losses appears when small inclinations of the tested structure occurs. An important factor which affects directly these losses has been observed, it consists of the Lamb waves beam (LWB) deviation due to this bad alignment. In this work, a simple expression of LWB deviation has been deduced. This expression includes the test structure angle, phase velocity of generated Lamb mode, and the phase velocity of waves propagating in the coupled medium. A(0) Lamb mode is generated and detected in 1 mm thick aluminium plate sample using 1 MHz PZ27 piezoelectric transducers of 20 mm of diameter. Experimental LWB deviation angles are measured for different inclination angles of the test sample. A comparative study is released with theoretical results. For 1 degree of misalignment in the aluminium plate inclination, and transducers separation distance of 35 mm, LWB deviation angle is around 7 degrees and the amplitude is reduced by around 11%. Then, for a large separation distance, we must move the receiver transducer to detect the deviated LWB. It is shown that, for both theoretical and experimental studies, the LWB deviation and its measured amplitude are very sensitive to the alignment of the tested structure with respect to the transmitter-receiver transducers plane. In metal plates it is most satisfactory to use A(0) mode compared with S(0) mode since it is easy to excite and has a large amplitude and small deviation beam angles.     

General solution of cumulative second harmonic by Lamb wave propagation in a solid plate

A straightforward approach has been developed for the general solution of cumulative second harmonic by Lamb wave propagation in a solid plate. The present analyses of second-harmonic generation by Lamb waves focus on the cases where the phase velocity of the fundamental Lamb wave is exactly or approximately equal to that of the double frequency Lamb wave （DFLW）. Based on the general solution obtained, the numerical analyses show that the cumulative second-harmonic fields are associated with the position of excitation source and the difference between the phase velocity of the fundamental Lamb wave and that of the dominant DFLW component.     

用分数阶微分实现时频重叠多模式兰姆波的模式分离

为了分离时频重叠多模式超声兰姆波,提出了一种用分数阶微分理论实现多模式兰姆波模式分离的方法。以时频重叠的S1和A1模式混合信号为例,用赛利斯分布作为幅值谱的模型,首先对信号做频散补偿,由补偿后信号幅值谱分数阶微分推导了幅值谱特征参数的计算式并根据信号模型重建幅值谱,然后结合兰姆波的频散特性推导出对应的相位谱,并通过幅值谱和相位谱重构各模式的信号,实现模式分离。对1 mm钢板中仿真时频重叠的S₁和A₁模式信号分离结果显示分离出信号的幅值和带宽相对误差小于6%,中心频率相对误差小于0.25%。实验结果也证实了方法的可行性。因此当混合信号幅值谱不完全交叠时,本方法可以实现多模式兰姆波信号的分离,有助于多模式兰姆波频散信号的分析和识别。      

Microcrack localization using a collinear Lamb wave frequency-mixing technique in a thin plate

A novel Lamb wave frequency-mixing technique is proposed for locating microcracks in a thin plate,which does not require the resonance condition of Lamb wave mixing and can accurately locate the microcracks through only one-time sensing.Based on the bilinear stress-strain constitutive model,a two-dimensional finite element(FE)model is built to investigate the frequency-mixing response induced by the interaction between two primary Lamb waves and a microcrack.When two primary Lamb waves of A0 and S0 modes with different frequencies excited on the same side of the plate simultaneously impinge on the examined microcrack,under the modulation of the contact acoustic nonlinearity,the microcrack itself can be deemed as the secondary sound source and it will radiate the Lamb waves of new combined frequencies.Based on the time of flight of the generated A0 mode at difference frequency,an indicator named normalized amplitude index(NAI)is defined to directly locate the multi-microcracks in the given plate.It is found that the number and location of the microcracks can be intuitively visualized by using the NAI based frequency-mixing technique.It is also demonstrated that the proposed frequency mixing technique is a promising approach for the microcrack localization.     

时频域独立元分析方法实现超声兰姆波的多模式分离

为方便兰姆波信号分析与模式定征,提出一种将短时傅里叶变换(Short-Time Fourier Transform,STFT)与独立元分析(Independent Component Analysis,ICA)相结合的多模式超声兰姆波识别方法。首先通过STFT将兰姆波时域信号投影至时频域,基于各模式信号在时频域相对独立的特点,利用ICA实现混叠模式分离。根据分离模式时频能量脊提取各模式群速度曲线,进而估计板厚。将方法运用于时域有限差分(Finite-Difference Time-Domain,FDTD)法仿真与钢板实验,分离得到A0、A1和S0三种模式。仿真与实验中平均群速度估计误差约为1.5%和2.0%,板厚估计误差约为0.3%和2.0%。仿真结果表明,在信噪比(Signal-to-Noise Ratio,SNR)不小于0 dB的情况下,时频域独立元分析方法均可实现兰姆波多模式分离、群速度曲线提取及板厚估计。      

Numerical predictions and experiments on the free-plate edge mode

In this paper, te edge mode variation is studied with three different methods: the reciprocal work method, already used by Torvik [J. Acoust. Soc. Am. 41 (1967) 346] to model this phenomenon, the S-parameter method and a finite element model that are applied for the first time to the study of the edge resonance. Moreover, laser probe measurements of the edge mode have also been performed and compared to the numerical predictions. The good agreement between the numerical predictions and the experimental data allows full understanding of the resonant phenomenon. The edge resonance is linked to the strong increase in amplitude of two complex Lamb waves, and the edge mode is proved to radiate into the plate as the first symmetrical Lamb mode S(0). Displacements at the edge and away from the edge have been computed and measured to evaluate the spatial and temporal behaviour of the edge mode. The dependence of the edge resonance frequency and amplitude on the Poisson coefficient has also been studied.     

Edge resonance and zero group velocity Lamb modes in a free elastic plate

The local resonances of a free isotropic elastic plate are investigated using laser ultrasonic techniques. Experimental results are interpreted in terms of zero group velocity Lamb modes and edge mode. At a distance from the edge larger than the plate thickness a sharp resonance is observed at the frequency where the group velocity of the first symmetrical Lamb mode vanishes. Close to the edge of the plate, the resonance due to the edge mode dominates. Both zero group velocity and edge resonances appear at the theoretically predicted frequencies. These frequencies do not vary with the distance from the edge of the plate and the transition between the two modes of vibration, at about the plate thickness, is abrupt. Using a laser excitation on the edge, the amplitude profile of the normal displacement at the edge resonance frequency was determined.     

固体板中SH板波非线性效应的实验观察

采用微扰近似和导波的模式展开分析方法,从理论上简要分析了SH板波的二次谐波发生效应;尽管在无限大固体介质中单个切变波的二次谐波发生效应非常微弱,但在一定条件下由两个切变波构成的SH板波可具有强烈的非线性效应;本文的主要工作就是对此结论加以实验验证。试制了激发SH板波的切变波斜劈换能器和接收二次谐波信号的液体斜劈换能器,建立了非线性SH板波的实验研究系统;通过详细的理论分析和对比实验研究,阐明了在一定条件下实验观察到的显著二次谐波信号来源于SH板波传播过程中的强烈非线性效应。此外,针对不同的SH板波传播距离,在远场条件下分别测量了相应的二次谐波幅频曲线;在基频SH板波与二倍频对称兰姆波相速度相等所对应的频率值附近,分析了二次谐波的振幅随传播距离的变化关系,结果证明在一定条件下SH板波的二次谐波振幅可随传播距离积累增长,即SH板波可具有强烈的非线性效应。      

轨道板中超声兰姆波传播的有限元计算和实验*

该文针对我国高速铁路轨道板缺陷的非接触动态检测问题,研究了空气耦合超声兰姆波在轨道板中的传播规律。首先,给出了轨道板中超声兰姆波的相速度和群速度频散曲线,结果表明:随着频厚积的增加,频散现象越明显,并且A0相速度收敛于Rayleigh波的波速。然后,建立轨道板中波传播的有限元模型,计算得到兰姆波传播的群速度为2220 m/s,且二维傅里叶变换系数的较大值沿Rayleigh波的频散曲线分布。最后,在沪杭高铁嘉兴南站进行了现场测试,以8.8°倾斜角向轨道板激励产生超声兰姆波,激发产生的兰姆波模态群速度为2325 m/s,且二维傅里叶变换分析其系数的较大值沿Rayleigh波的频散曲线分布。有限元计算结果和实验结果均与理论计算结果一致。该研究为后续轨道板缺陷的非接触动态检测提供了理论依据和实验方法。     

Micro-crack detection of nonlinear Lamb wave propagation in three-dimensional plates with mixed-frequency excitation

We propose a nonlinear ultrasonic technique by using the mixed-frequency signals excited Lamb waves to conduct micro-crack detection in thin plate structures. Simulation models of three-dimensional(3D) aluminum plates and composite laminates are established by ABAQUS software, where the aluminum plate contains buried crack and composite laminates comprises cohesive element whose thickness is zero to simulate delamination damage. The interactions between the S_0 mode Lamb wave and the buried micro-cracks of various dimensions are simulated by using the finite element method.Fourier frequency spectrum analysis is applied to the received time domain signal and fundamental frequency amplitudes,and sum and difference frequencies are extracted and simulated. Simulation results indicate that nonlinear Lamb waves have different sensitivities to various crack sizes. There is a positive correlation among crack length, height, and sum and difference frequency amplitudes for an aluminum plate, with both amplitudes decreasing as crack thickness increased, i.e.,nonlinear effect weakens as the micro-crack becomes thicker. The amplitudes of sum and difference frequency are positively correlated with the length and width of the zero-thickness cohesive element in the composite laminates. Furthermore,amplitude ratio change is investigated and it can be used as an effective tool to detect inner defects in thin 3D plates.