Highly selective thiocyanate electrode based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) complex as a neutral carrier.

A novel selective thiocyanate electrode of a PVC membrane based on bis-[N-(2-hydroxyethyl)salicylaldimino]copper(II) [Cu(II)-BNSDM] as a neutral carrier is reported. The selectivity sequence of this electrode is as follows: SCN- > ClO4- > I- > Sal- > Br- > NO2- > Cl- > NO3- > H2PO4- > SO4(2-), which is an anti-Hofmeister selectivity sequence. The electrode exhibits a Nernstian potential linear range to thiocyanate from 1.0 x 10(-1) to 6.0 x 10(-6) mol/L with a detection limit of 2.0 x 10(-6) mol/L and a slope of (-59.0+/-0.2)mV/decade in pH 5.0 of a phosphate buffer solution at 25 degrees C. Electrochemical impedance spectroscopy (EIS) and UV spectroscopy techniques were performed to understand the response mechanism of the electrode. The electrode had the advantage of simplicity, high selectivity, fast response and low detection limit compared with the other electrode, which had been reported before. The electrode had been applied to wastewater analysis, and the obtained results were satisfactory.     

Bis-dimethylaminobenzaldehyde Schiff-base cobalt(II) complex as a neutral carrier for a highly selective iodide electrode.

A new solvent polymeric membrane electrode based on N,N'-bis-(dimethylaminobenzaldehyde)-glycine cobalt(II) [Co(II)-BDMABG] as a neutral carrier is described, which displays a preferential potentiometric response to iodide ion and an anti-Hofmeister selectivity sequence in the following order: I- > ClO4- > Sal- > SCN- > NO2- > Br- > NO3- > Cl- > SO3(2-) > SO4(2-). The electrode exhibits a near-Nernstian potential linear range of 9.0 x 10(-7)-1.0 x 10(-1) M with a detection limit of 6.8 x 10(-7) M and a slope of -53.0 mV/decade in pH 2.0 of a phosphate buffer solution at 20 degrees C. The response mechanism is discussed in view of the A.C. impedance technique and the UV spectroscopy technique. The electrode was successfully applied to the determination of iodide in Jialing River and Spring in Jinyun Mountains with satisfactory results.     

苯甲醛缩氨基脲铜（II）配合物为载体的高选择性硫氰酸根离子电极的研究

首次研究以苯甲醛缩氨基脲铜（II）[Cu(II)-BASA]为中性载体的PVC膜电极， 该电极对硫氰酸根离子（SCN~-）具有优良的电位响应特性并呈现出反Hofmeister 选择性行为，其选择性次序为：SCN~- > ClO_4~- > I~- > Sal~- > Br~- > NO_3~- > Cl~- > NO_2~- > SO_3~(2-) > SO_4~(2-) > H_2PO_4~-。电极在pH 6. 0的磷酸盐缓冲体系中，对SCN~-在1.0 * 10~(-1)～8.0 * 10~(-6) mol/L浓度范围 内呈近能斯特响应，斜率为56.0 mV/sSCN~- (28 ℃)，检测下限为3.0 * 10~(-6) mol/L。采用交流阻抗技术和紫外可见光谱技术初步研究了阴离子与载体的作用机 理，结果表明配合物中心金属原子的结构以及载体本身的结构与电极的响应行为之 间有非常密切的构效关系。该电极具有响应快、重现性好、检测限低、制备简单等 优点。将电极初步应用于实际样品废水分析，结果与HPLC法一致。     

Highly selective iodide electrode based on the copper(II)-N,N'-bis(salicylidene)-1,2-bis(p-aminophenoxy)ethane tetradentate complex.

In this paper, a new PVC-based liquid-membrane anion-selective electrode based on a copper(II) of N,N'-bis(salicylidene)-1,2-bis(p-aminophenoxy)ethane tetradentate complex (Cu(II)BBAP) is described, which displays a preferential potentiometric response to iodide ion at pH 2.0 and an anti-Hofmeister selectivity sequence: I->SCN->ClO4->NO2->H2PO4->NO3->SO4(2-)>Br->Cl-. The electrode exhibits a near-Nernstian potential linear range of 8.2x10(-7)-1.0x10(-1) M with a detection limit of 5.3x10(-7) M and a slope of -58.8 mV per decade. The A.C. impedance technique and the UV/Vis spectroscopy technique were used to analyze the response mechanism. The electrode could be applied to determine iodide in medicine analysis, and the obtained results were fairly satisfactory.     

Novel sulfate ion-selective polymeric membrane electrode based on a derivative of pyrilium perchlorate

A sulfate ion-selective PVC membrane sensor based on 4-(4-bromophenyl)-2,6-diphenylpyrilium perchlorate (BDPP) as a novel sensing material is successfully developed. The electrode shows a good selectivity for sulfate ion with respect to common organic and inorganic anions. The sensor exhibits a good linear response with slope of -28.9+/-0.5 mV per decade over the concentration range of 1.0x10(-6)-1.0x10(-2) M, and a detection limit of 8.0x10(-7) M of SO(4)(2-) ions. The electrode response is independent of pH in the range of 4.0-9.0. The proposed sensor was applied as an indicator electrode in potentiometric titration of sulfate and barium ions, and to the determination of zinc in zinc sulfate tablets.     

Binuclear Schiff base complex of manganese(III) as a neutral carrier for a highly selective iodide electrode.

A new highly selective iodide electrode incorporating a binuclear manganese(III) complex, bis(salicylaldehyde-aminopropanol)dichloroaceticdimanganese(III) [Mn(III)(2)-BSAPDCA], as a neutral carrier is described. The electrode displays an anti-Hofmeister selectivity sequence: iodide > perchlorate > salicylate > thiocyanate > nitrate > bromide > nitrite > chloride > sulfate. The excellent selectivity for iodide is related to a direct interaction between the central Mn(III) atom and iodide and a steric effect associated with the structure of the carrier, which is supported by UV spectroscopy and AC impedance techniques. The electrode exhibits a near-Nernstian potentiometric linear response range to iodide from 1.0 x 10(-1) to 2.0 x 10(-5) mol/L with a detection limit of 8.0 x 10(-6) mol/L and a slope of -60.3 mV/decade in pH 3.0 of phosphate buffer solutions at 20 degrees C. From a comparison of the potentiometric response characteristics between a binuclear manganese(III) complex, Mn(III)(2)-BSAPDCA, and a mononuclear manganese(III) complex, Mn(III)-BSAPB, an enhanced response towards iodide from a binuclear metallic complex-based electrode was observed. The electrode, based on binuclear manganese(III) complex, was successfully applied to the determination of inorganic total iodine in iodized table salt with satisfactory results.     

Ion-selective electrodes for anionic surfactants using a cyclam derivative as ionophore

The cyclam derivative 1,4,8,11-tetra(n-octyl)-1,4,8,11-tetraazacyclotetradecane (L) has been used as carrier for the preparation of PVC-based membrane ion-selective electrodes for anionic surfactants. Different membranes were prepared using L as ionophore, tetra-n-octylammonium bromide (TOAB) as cationic additive and dibutyl phthalate (DBP) or o-nitrophenyl octyl ether (NPOE) as plasticizers. The final used electrode contained a membrane of the following composition: 56% DBP, 3.4% ionophore, 3.8% TOAB and 36.8% PVC. This electrode displays a Nernstian slope of -60.0+/-0.9 mV/decade in a 2.0 x 10(-3) to 7.9 x 10(-6) mol dm(-3) concentration range and a limit of detection of 4.0 x 10(-6) mol dm(-3). The electrode can be used for 144 days without showing significant changes in the value of slope or working range. The electrode shows a selective response to dodecyl sulfate (DS-) and a poor response to common inorganic cations and anions. The selective sequence found was DS->ClO4->HCO3->SCN->NO3- approximately CH3COO- approximately I->Cl->Br->IO3- approximately NO2- approximately SO3(2-)>HPO4(2-)>C2O4(2-)>SO4(2-), i.e. basically following the Hoffmeister series except for the hydrophilic anion bicarbonate. Most of the potentiometric coefficients determined are relatively low indicating that common anions would not interfere in the DS- determination. A complete study of the response of the electrode to a family of surfactant was also carried out. The electrode showed a clear anionic response to DS- and to Na-LAS and a much poorer response to other anionic surfactants and to non-ionic surfactants. Also the electrode shows certain non-linear cationic response in the presence of cationic and zwitterionic surfactants. The electrode was used for the determination of anionic surfactants in several mixtures, and the results obtained were compared to those found using a commercially available sensor.     

A metallic cobalt electrode for the indirect potentiometric determination of calcium and magnesium in natural waters using flow injection analysis

A flow injection analysis of Ca(2+) and Mg(2+) using indirect potentiometric detection in natural waters is proposed, where Ca(2+) or Mg(2+) are injected into a buffer carrier containing phosphate, resulting in the formation of Ca(3)(PO(4))(2) or Mg(3)(PO(4))(2). The consequent reduction in free phosphate in the carrier solution is detected using a metallic cobalt wire electrode. Indirect electrode response was used and the experimental conditions affecting electrode response were optimized. Responses were linear in the concentration range 5x10(-4) to 5x10(-3) M with a detection limit of 1x10(-5) M in 20 mM phosphate buffer at pH 8.0. The relative standard derivation at 1 mM of Ca(2+) and Mg(2+) were 3.9 and 3.7% (n=10), respectively. EGTA and 8-hydroxyquinoline were used as the masking agents for Ca(2+) and Mg(2+), respectively. Concentrations of Ca(2+) and Mg(2+) in natural waters were successfully determined by the proposed method.     

Sulfate-selective electrode based on a complex of copper.

A new sulfate-selective electrode based on the complex N,N'-bis(2-amino-1-oxo-phenelenyl)phenylenediamine copper(II) (CuL) as the membrane carrier was developed. The electrode exhibited a good Nernstian slope of -29.5 +/- 0.5 mV/decade and a linear range of 1.0 x 10(-7) - 1.0 x 10(-1) M for sulfate. The limit of detection was 1.0 x 10(-8) M. It has a fast response time of 10 s and can be used for more than three months. The selective coefficients were determined by the fixed interference method (FIM). The electrode could be used in the pH range 3.5 - 8.0. It was employed as an indicator electrode for direct determination of sulfate in pharmacy and cement samples.     

Chronocoulometric determination of nitrate on silver electrode and sodium hydroxide electrolyte

An electrochemical system that consists of a silver electrode in 0.01 M sodium hydroxide electrolyte was investigated in an effort to develop a sensitive in situ analytical method for nitrate. Cyclic voltammetry demonstrated that the proposed system has a high normalized sensitivity (2.47 A s(1/2) V(-1/2) M(-1) cm(-2)), compared to more complex electroanalytical schemes. Double-potential-step chronocoulometry was used to maximize the signal-to-noise ratio (SNR), and minimize interference from dissolved oxygen in the electrolyte. The integration period for double-potential-step chronocoulometry was determined by optimizing the extended Cottrell equation. The integrated current is proportional to nitrate up to 10 mM and the average detection limit is approximately 1.7 microM. Dissolved oxygen does not degrade performance. To examine the potential interference of other ions when analyzing nitrate, we measured the electrode response to 1000 microM each of NO(2-), Cl(-), PO(4)(3-), SO(4)(2-), F(-), CO(3)(2-), BO(2-), K(+), Ca(2+), and Sr(2+) with and without 1000 microM nitrate. Interference is negligible for most of the ions when nitrate is absent (i.e. <1% of the response to equimolar nitrate). However, interference is substantial (>20% increase or decrease in the electrode response to nitrate) for PO(4)(3-), Ca(2+), and Sr(2+) when equimolar nitrate is present.     

Photochemical investigation of Roussin's red salt esters: Fe2(mu-SR)2(NO)4

The photochemistry of various Roussin's red ester compounds of the general formula Fe(2)(SR)(2)(NO)(4), where R = CH(3), CH(2)CH(3), CH(2)C(6)H(5), CH(2)CH(2)OH, and CH(2)CH(2)SO(3)(-), were investigated. Continuous photolyses of these ester compounds in aerated solutions led to the release of NO with moderate quantum yields for the photodecomposition of the ester (Phi(RSE) = 0.02-0.13). Electrochemical studies using an NO electrode demonstrated that 4 mol of NO are generated for each mole of ester undergoing photodecomposition. Nanosecond flash photolysis studies of Fe(2)(SR)(2)(NO)(4) (where R = CH(2)CH(2)OH and CH(2)CH(2)SO(3)(-)) indicate that the initial photoreaction is the reversible dissociation of NO. In the absence of oxygen, the presumed intermediate, Fe(2)(SR)(2)(NO)(3), undergoes second-order reaction with NO to regenerate the parent cluster with a rate constant of k(NO) = 1.1 x 10(9) M(-1) s(-1) for R = CH(2)CH(2)OH. Under aerated conditions the intermediate reacts with oxygen to give permanent photochemistry.     

Electrochemical response of dopamine at a penicillamine self-assembled gold electrode.

The penicillamine (Pen) self-assembled monolayer (SAM) modified gold electrode (Pen/Au) is demonstrated to catalyze the electrochemical response of dopamine (DA) by cyclic voltammetry. A pair of well-defined redox waves was obtained and the calculated standard rate constant (k(s)) is 3.88 x 10(-3) cm/s at the self-assembled electrode. The electrode reaction is a quasi-reversible process. The oxidation peak of DA can be used to determine the concentration of DA. The peak current and the concentration of DA are a linear relationship in the range of 2.0 x 10(-5) M to 8.0 x 10(-4) M. The detection limit is 4.0 x 10(-6) M. By ac impedance spectroscopy the apparent electron transfer rate constant (k(app)) of Fe(CN)(3-)/Fe(CN)(4-) at the Pen/Au electrode was obtained as 2.08 x 10(-5) cm/s. The Pen SAM was characterized with X-ray photoelectron spectroscopy (XPS), grazing angle FT-IR spectroscopy and contact angle goniometer.     

Determination of acetylsalicylic acid by FIA-potentiometric system in drugs after on-line hydrolysis

A potentiometric flow injection (FI) system was developed for the acetylsalicylic acid (ASA) determination in drugs, without previous treatment. The tubular potentiometric electrode for salicylate (SA) was based on tricaprylyl-trimethyl-ammonium-salicylate (aliquat-salicylate) as the ion-exchanger, supported on poly(ethylene-co-vinyl-acetate) (EVA) matrix and applied directly onto a conducting support. The standards and samples were freshly prepared in ethanol solution (0.10 mol l(-1) Tris-SO(4) buffer, pH 8.0, containing 0.25 mol l(-1) Na(2)SO(4) and 8.0% v/v ethanol) to facilitate the dissolution of ASA and were injected directly into the system. The SA formed due to the on-line alkaline hydrolysis of alcoholic ASA solution, with 0.50 mol l(-1) NaOH (coil, 50 cm length), was monitored by the tubular electrode after neutralization with 0.25 mol l(-1) H(2)SO(4). A solution of 0.10 mol l(-1) Tris-SO(4) buffer (pH 8.0), containing 0.25 mol l(-1) Na(2)SO(4) was employed as carrier. In optimized conditions (flow rate of 2.1 ml min(-1) and volume of injection of 150 mul), the tubular electrode showed a linear response to ASA in the concentration range between 4.0x10(-3) and 4.0x10(-2) mol l(-1). A conversion factor of ASA to SA of 85% occurs in these conditions with an increase of about 130% in the signal to the system with on-line hydrolysis (three-channel) in comparison to the system without (one-channel). The response time of the electrode was about 5 s with an analytical frequency of 28 samples per h and a relative standard deviation (R.S.D.) of 2.1% for 30 successive injections. Determinations of ASA in tablet samples by the proposed method exhibited relative differences of 1.0-3.5%, compared to the official method of the British Pharmacopoeia. The useful lifetime of the sensor was greater than 1 month, in continuous use.     

The use of phenylfluorone in the presence of cetylpyridinium chloride and Triton X-100 for the spectrophotometric determination of copper(II) in blood serum

A simple and sensitive spectrophotometric method for determination of copper(II) is based on the formation of a blue coloured complex of Cu(II) with 9-phenyl-2,3,7-trihydroxy-6-fluorone (PF) in the presence of cetylpyridinium chloride (CP) and Triton X-100, has been developed. Optimum concentrations of PF, CP, Triton X-100 and pH ensuring maximum absorbance were defined. The complex Cu(II)-PF-CP-Triton X-100 shows maximum absorbance at 595 nm with a molar absorptivity value of 9.67x10(4) l mol(-1) cm(-1). The detection limit of the method is 0.028 mug ml(-1). Beer's law is obeyed for copper concentrations in the range 0.04-0.4 mug ml(-1). The studies of the effect of foreign ions on determination of copper, show that the selectivity of the method is poor. The cations of alkali metals and anions Br(-), Cl(-), I(-), F(-), NO(2)(-), NO(3)(-), CH(3)COO(-), SO(4)(2-), S(2)O(3)(2-), PO(4)(3-), citrates (examined in 1000-fold molar excess over copper) do not affect the determination. All cations forming complexes with PF have an interfering effect. The statistical evaluation of the method was carried out for six determinations using 10 mug of Cu and the following results were obtained: the standard deviation, SD=0.042, the confidence interval mu(95)=10.1+/-0.1 mug Cu. The method has been applied for determination of copper in blood serum.     

Copper (II) ion selective liquid membrane electrode based on new Schiff base carrier

Cu2+ selective PVC membrane electrode based on new Schiff base 2, 2'-[1,9 nonanediyl bis (nitriloethylidyne)]-bis-(1-naphthol) as a selective carrier was constructed. The electrode exhibited a linear potential response within the activity range of 1.0 x 10(-6) - 5.0 x 10(-3) moll(-1) with a Nernstian slope of 29 +/- 1 mV decade(-1) of Cu2+ activity and a limit of detection 8.0 x 10(-7) mol l(-1). The response time of the electrode was fast, 10 s, and stable potentials were obtained within the pH range of 3.5- 6.5. The potentiometric selectivity coefficients were evaluated using two solution method and revealed no important interferences except for Ag+ ion. The proposed electrode was applied as an indicator electrode to potentiometric titration of Cu2+ ions and determination of Cu2+ content in real samples such as black tea leaves and multivitamin capsule.     

Crystallization pathways of sulfate-nitrate-ammonium aerosol particles

Crystallization experiments are conducted for aerosol particles composed of aqueous mixtures of (NH(4))(2)SO(4)(aq) and NH(4)NO(3)(aq), (NH(4))(2)SO(4)(aq) and NH(4)HSO(4)(aq), and NH(4)NO(3)(aq) and NH(4)HSO(4)(aq). Depending on the aqueous composition, crystals of (NH(4))(2)SO(4)(s), (NH(4))(3)H(SO(4))(2)(s), NH(4)HSO(4)(s), NH(4)NO(3)(s), 2NH(4)NO(3) x (NH(4))(2)SO(4)(s), and 3NH(4)NO(3) x (NH(4))(2)SO(4)(s) are formed. Although particles of NH(4)NO(3)(aq) and NH(4)HSO(4)(aq) do not crystallize even at 1% relative humidity, additions of 0.05 mol fraction SO(4)(2-)(aq) or NO(3)(-)(aq) ions promote crystallization, respectively. 2NH(4)NO(3) x (NH(4))(2)SO(4)(s) and (NH(4))(3)H(SO(4))(2)(s) appear to serve as good heterogeneous nuclei for NH(4)NO(3)(s) and NH(4)HSO(4)(s), respectively. 2NH(4)NO(3) x (NH(4))(2)SO(4)(s) crystallizes over a greater range of aqueous compositions than 3NH(4)NO(3) x (NH(4))(2)SO(4)(s). An infrared aerosol spectrum is provided for each solid based upon a linear decomposition analysis of the recorded spectra. Small nonzero residuals occur in the analysis because aerosol spectra depend on particle morphology, which changes slightly across the range of compositions studied. In addition, several of the mixed compositions crystallize with residual aqueous water of up to 5% particle mass. We attribute this water content to enclosed water pockets. The results provide further insights into the nonlinear crystallization pathways of sulfate-nitrate-ammonium aerosol particles.     

Lead(II)-selective electrode based on phenyl disulfide.

A PVC membrane electrode for lead ions based on phenyl disulfide as the membrane carrier was developed. The electrode exhibits a good Nernstian slope of 29.3 +/- 0.7 mV/decade and a linear range of 2.0 x 10(-6)-1.0 x 10(-2) M for Pb(NO3)2. The limit of detection is 1.2 x 10(-6) M. It has a response time of 45 s and can be used for at least fifty days without any divergence in potential. The proposed membrane sensor revealed high selectivity for Pb2+ over a wide variety of other metal ions and could be used in the pH range of 3.5-6.3. The electrode was used as an indicator electrode in potentiometric titration of lead ions.     

Highly Thiocyanate‐Selective PVC Membrane Electrode Based on Lipophilic Ferrocene Derivative

A novel anion‐selective PVC membrane electrode based on bis‐[(3‐ferrocenyl)‐(2‐crotonic acid)] copper(II) complex [Cu(II)‐BFCA] as neutral carrier is described, which demonstrates excellent potentiometric response characteristics toward thiocyanate ion and anti‐Hofmeister selectivity sequence in following order: SCN^?>I^?>ClO >Sal^?>Br^?>NO >Cl^?≈NO >SO >SO . The electrode shows a near‐Nernstian response for thiocyanate ion in a wide range of 9.0×10^?7–1.0×10^?1 M with a detection limit 6.8×10^?7 M and a slope of ?59.1 mV/decade in pH 5.0 of phosphate buffer solution at 20 °C. The influences of lipophilic cationic and anionic additives on the response properties of the electrode were investigated. High sensitivity and wide linear dynamic range were observed for the electrode in the presence of hexadecyltrimethylammoniumborate (HTAB) as a lipophilic cationic additive. The electrode was successfully applied to the determination of thiocyanate ion in waste water and human saliva.     

A novel thiocyanate-selective electrode based on a zinc–phthalocyanine complex

A novel thiocyanate (SCN⁻)-selective PVC membrane electrode based on a zinc-phthalocyanine (ZnPc) complex as neutral carrier is described. The membrane electrode containing ZnPc with 5.1% (w/w) ionophore, 29.2% (w/w) PVC, and 65.7% (w/w) 2-nitrophenyl octyl ether (o-NPOE) as plasticizer displayed an anti-Hofmeister selectivity sequence , and exhibited near-Nernstian potential response to thiocyanate ranging from about 1.0×10⁻¹ to 1.0×10⁻⁶ mol L⁻¹ with a detection limit of 7.5×10⁻⁷ mol L⁻¹ and a slope of 58.1±0.5 mV per decade in pH 3.0 phosphate buffer solution at 25 °C. This preferential response is believed to be associated with the unique coordination between the central metal of the carrier and thiocyanate.      

Anion exchange induced tunable catalysis properties of an uncommon butterfly-like tetranuclear copper(II) cluster and magnetic characterization

An uncommon butterfly-like tetranuclear copper(ii) cluster with the formula {[Cu(4)(μ(3)-OH)(2)(μ(4)-Cl)(H(2)O)(2)(L)(2)]·Cl(H(2)O)(7)}(n) (1) (H(2)L = 1,2-bis[3-(1,2,4-triazolyl)-4-amino-5-carboxylmethylthio]ethane) has been synthesized. Compound 1 exhibits interesting anion exchange characteristics, in which both guest and coordinated Cl(-) can be replaced by I(-) or NO(3)(-) in water. Furthermore, a high catalytic selectivity to produce poly(phenylene ether) by the oxidative coupling of 2,6-dimethylphenol in water is found to be 74% for 1 and 87% for the anion-exchanged product 1-MI(x), respectively. Additionally, the antiferromagnetic interaction among Cu ions for compound 1 is also found.