Photoelectrochemical properties of texture‐controlled nanostructured α‐Fe2O3 thin films prepared by AACVD

Nanostructured α‐Fe₂O₃ thin film electrodes were deposited by aerosol‐assisted chemical vapour deposition (AACVD) for photoelectrochemical (PEC) water splitting on conducting glass substrates using 0.1 M methanolic solution of Fe(acac)₃. The XRD analysis confirmed that the films are highly crystalline α‐Fe₂O₃ and free from other iron oxide phases. The highly reproducible electrodes have an optical bandgap of ～2.15 eV and exhibit anodic photocurrent. The current–voltage characterization of the electrodes reveals that the photocurrent density strongly depended on the film morphology and deposition temperature. Scanning electron microscopy (SEM) analysis showed a change in the surface morphology with the change in deposition temperature. The films deposited at 450 °C have nanoporous structures which provide a maximum electrode/electrolyte interface. The maximum photocurrent density of 455 µA/cm² was achieved at 0.25 V vs. Ag/AgCl/3M KCl (～1.23 V vs. RHE) and the incident photon to electron conversion efficiency (IPCE) was 23.6% at 350 nm for the electrode deposited at 450 °C. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

High‐gain Zn1–xMgx O‐based ultraviolet photodetectors on Al2O3 and LiGaO2 substrates

We report the fabrication and characterization of highly responsive ZnMgO‐based ultraviolet (UV) photodetectors in the metal–semiconductor–metal (MSM) configuration for solar‐blind/visible‐blind optoelectronic application. MSM devices were fabricated from wurtzite Zn_1–xMg_x O/ZnO (x ～ 0.44) thin‐film heterostructures grown on sapphire (α‐Al₂O₃) substrates and w‐Zn_1–xMg_x O (x ～ 0.08), grown on nearly lattice‐matched lithium gallate (LiGaO₂) substrates, both by radio‐frequency plasma‐assisted molecular beam epitaxy (PAMBE). Thin film properties were studied by AFM, XRD, and optical transmission spectra, while MSM device performance was analyzed by spectral photoresponse and current–voltage techniques. Under biased conditions, α‐Al₂O₃ grown devices exhibit peak responsivity of ～7.6 A/W at 280 nm while LiGaO₂ grown samples demonstrate peak performance of ～119.3 A/W, albeit in the UV‐A regime (～324 nm). High photoconductive gains (76, 525) and spectral rejection ratios (～10³, ～10⁴) were obtained for devices grown on α‐Al₂O₃ and LiGaO₂, respectively. Exemplary device performance was ascribed to high material quality and in the case of lattice‐matched LiGaO₂ films, decreased photocarrier trapping probability, presumably due to low‐density of dislocation defects. To the best of our knowledge, these results represent the highest performing ZnO‐based photodetectors on LiGaO₂ yet fabricated, and demonstrate both the feasibility and substantial enhancement of photodetector device performance via growth on lattice‐matched substrates. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Metal-semiconductor-metal ultraviolet photodetector based on GaN

A metal-semiconductor-metal (MSM) ultraviolet photodetector has been fabricated using unintentionally doped n-GaN films grown on sapphire substrates. Its dark current, photocurrent under the illumination with λ = 360 nm light, responsivity, and the dependence of responsivity on bias voltage were measured at room temperature. The dark current of the photodetector is 1.03 Na under 5 V bias, and is 15.3 Na under 10 V bias. A maximum responsivity of 0.166 A/W has been achieved under the illumination with λ= 366 nm light and 15 V bias. It exhibits a typical sharp band-edge cutoff at the wavelength of 366 nm, and a high responsivity at the wavelength from 320 nm to 366 nm. Its responsivity under the illumination with λ= 360 nm light increases when the bias voltage increases.     

Au/TiO2 nanorod‐based Schottky‐type UV photodetectors

TiO₂ nanorods (NRs) were synthesized on fluorine‐doped tin oxide (FTO) pre‐coated glass substrates using hydrothermal growth technique. Scanning electron microscopy studies have revealed the formation of vertically‐aligned TiO₂ NRs with length of ～2 µm and diameter of 110–128 nm, homogenously distributed over the substrate surface. 130 nm thick Au contacts using thermal evaporation were deposited on the n‐type TiO₂ NRs at room temperature for the fabrication of NR‐based Schottky‐type UV photodetectors. The fabricated Schottky devices functioned as highly sensitive UV photodetectors with a peak responsivity of 134.8 A/W (λ = 350 nm) measured under 3 V reverse bias. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Enhancing photoresponse time of low cost Pd/ZnO nanorods prepared by thermal evaporation techniques for UV detection

High quality undoped ZnO nanorods have been synthesized at 850 °C by vapor-solid (VS) technique without a catalyst through a low cost process on silicon substrates. Then, ZnO nanorods have been characterized by using scanning electron microscopy (SEM), X-ray diffractometer (XRD), and photoluminescence (PL) spectroscopy. Metal-semiconductor-metal (MSM) photodetectors with palladium (Pd) as contact electrodes have been successfully constructed for ultraviolet (UV) detection. Under dark and UV illumination, the load resistance of the Pd/ZnO junction was found to be 80.4 kΩ, and 23.5 kΩ referring to the maximum allowed bias voltage; the barrier height was estimated to be about 0.8 eV, and 0.76 eV, at 5 V applied bias voltage, respectively. It was found that the maximum responsivity of the Pd/ZnO MSM photodetector was 0.106 A/W at 300 nm which corresponds to a quantum efficiency of 43.8% at 5 V applied bias voltage. The transient photoresponse of the fabricated device is reported under different applied biases at 1 V, 3 V, and 5 V.     

Planar hybrid carbon-decorated zinc oxide nanowires for infrared photodetection

Vapor phase transport (VPT) assisted by thermal evaporation of methanol was utilized to favor the fabrication of hybrid carbon-decorated zinc oxide nanowires (C/ZnO NWs). The photoluminescence (PL) spectrum revealed evidence of optical properties for several defects such as zinc interstitials (Zn_i) and oxygen vacancy (V_o) in hybrid C/ZnO NWs. The PL also exhibited that the planar hybrid C/ZnO NWs photodetector has a wide range of sensitivity from ultraviolet (UV) to infrared (IR). The imaging results show formation of ZnO nanostructures which can be further confirmed from X-ray diffraction (XRD) results. XRD exhibits carbon (C)-related peaks at 12.88, 26, 43, 45, and 55° together with standard ZnO peaks. The incorporation of C shows excellent photoconduction towards varied laser powers (0.0, 7.82, 37.95, 69.20, 100.0, 130.0, and 160.0 mW) of IR illumination. The possibility of current drain in the device was evaluated based on the direct-current (DC) bias voltage of 0.00, 3.33, and 5.55 V. DC bias 3.33 and 5.55 V attributed increase of photocurrent towards the forward bias voltage. However, the reverse bias voltage illustrated a vast increase of photocurrent compared to the forward bias voltage. External quantum efficiency (EQE) at DC bias 5.55 V was 6.5–9.5 range folds greater than the EQE measured for zero bias voltage. Significant photoresponsivity was identical for various laser pulse ranging from 10 to 5000 Hz. Simultaneously, the rise (τ_r) and fall (τ_f) time were measured at 49 and 60.5 μs attributes that the fabrication technique can be improvised and implemented to enhance the efficiency of optoelectronic devices for future applications.     

Electrical characteristics of UV photodetectors based on ZnO/diamond film structure

Ultraviolet photodetectors based on ZnO/diamond film structure were fabricated. The properties of Au/ZnO contacts and effects of grain sizes on the electrical characteristics of photodetectors were discussed. Due to the bombardment with Au atoms and the annealing process, fine ohmic contacts were formed between Au electrodes and ZnO films. Dark currents and photocurrents of the photodetectors were related to sputtering time and the grain size of ZnO films. For the photodetector with a bigger grain size, a lower dark current and a higher photocurrent were obtained under 10 V bias voltage. The time-dependent photocurrent confirmed the carrier trapping effect.     

Fast piezoresistive sensor and UV photodetector based on Mn‐doped ZnO nanorods

A low cost hydrothermal synthesis method to synthesize Mn‐doped ZnO nanorods (NRs) with controllable morphology and structure has been developed. Ammonia is used to tailor the ammonium hydroxide concentration, which provides a source of OH^– for hydrolysis and precipitation during the growth instead of HMT. The morphological, chemical composition, structural, and electronic structure studies of the Mn‐doped ZnO NRs show that the Mn‐doped ZnO NRs have a hexagonal wurtzite ZnO structure along the c‐axis and the Mn ions replace the Zn sites in the ZnO NRs matrix without any secondary phase of metallic manganese element and manganese oxides observed. The fabricated PEDOT:PSS/Zn_0.85Mn_0.15O Schottky diode based piezoresistive sensor and UV photodetector shows that the piezoresistive sensor has pressure sensitivity of 0.00617 kPa^–1 for the pressure range from 1 kPa to 20 kP and 0.000180 kPa^–1for the pressure range from 20 kPa to 320 kPa with relatively fast response time of 0.03 s and the UV photodetector has both relatively high responsivity and fast response time of 0.065 A/W and 2.75 s, respectively. The fabricated Schottky diode can be utilized as a very useful human‐friendly interactive electronic device for mass/force sensor or UV photodetector in everyday living life. This developed device is very promising for small‐size, low‐cost and easy‐to‐customize application‐specific requirements. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

White light electroluminescence from poly(9-vinylcarbazole) (PVK)/ZnO NRs/poly(2-methoxy-5-(2-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) dual heterojunctions

In this paper, we fabricated a p-PVK/n-ZnO nanorods (NRs)/p-MEH-PPV dual heterojunctions white light-emitting diode. Relative to previously reported p–n heterojunction structure including ZnO NRs and polymer, the device exhibits a low turn-on voltage of 7 V. An obviously broad electroluminescence emission band, originated from the overlap of PVK emission and ZnO defects emissions, was observed extending from 360 up to 700 nm. The influence of the two introduced p-type polymer layers on the device characteristic is discussed. With its hole conductivity, the p-PVK layer cannot only improve the holes tunnel into ZnO NRs layer, but also lower the barrier between ITO and the valance band of ZnO NRs. On the other hand, p-MEH-PPV could be regarded as block layer for the injection of electrons from the Al electrode. Both of two p-type polymers dramatically improve the injection balance of carriers, leading to a low turn-on voltage. Meanwhile, the carrier transport mechanism of the device under different forward bias region was discussed on the basis of current–voltage curve.     

Trapped charge‐induced pyroelectric‐like transient response in single high‐resistivity Sb2Se3 nanowires

Dynamic scanning photocurrent microscopy was applied to Sb₂Se₃ crystalline single nanowires (NWs) to analyze their transient photocurrent responses. These NWs exhibited switching behavior with rapid rise and decay times upon illumination by laser pulses. The estimated spectral responsivity and external quantum efficiency for a freshly‐prepared NW at a bias voltage of 0.3 V and excitation wavelength of 488 nm were ～16.9 mA/W and ～42.9%, respectively. A pyroelectric‐like current transient was observed with reduced spectral responsivity when nonpolar Sb₂Se₃ single‐crystalline NWs were excited by laser pulses. Because Sb₂Se₃ NWs were nonpyroelectric or ferroelectric, the pyroelectric‐like current could possibly be attributed to temperature dependent nonlinear space‐charge distributions. Defects produced by the external electrical bias generated and re‐distributed space charges in the NWs. As a result, the temperature dependent inhomogeneous electric field led to nonlinear expansions or contractions of the lattice (electrostriction) that can produce pyroelectric current. We obtained a lower bound of equivalent pyroelectric coefficient α ≥ 60.09 μC/m² K from these materials by fitting the electrical transients. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Binary response Se/ZnO p‐n heterojunction UV photodetector with high on/off ratio and fast speed

A high‐performance UV photodetector (PD) based on a p‐Se/n‐ZnO hybrid structure with large area (more than 1×1 cm) is presented in this study. The device is theoretically equivalent to a parallel‐connection circuit for its special structure and shows multifunction at different voltage bias, which means the output signal can be tailored by an applied voltage. The Se/ZnO PD shows binary response (positive and negative current output under on/off periodical light illumination) under small reverse bias (–0.05 V and –0.1 V) which efficiently reduces the negative effect of noise signal in weak‐signal detection applications. At zero bias, with the aid of a p‐n heterojunction, a high on/off ratio of nearly 10⁴ is achieved by this device at zero set bias under 370 nm (∼0.85 mW cm⁻²) illumination and this on/off ratio can be achieved in 0.5 s. The device also shows a fast speed with rise time of 0.69 ms and decay time of 13.5 ms measured by a pulse laser, much faster than that of a pure ZnO film. The Se/ZnO PD in this research provides a new pathway to fabricate multifunctional high‐speed, high signal‐to‐noise ratio, high detectivity and high selectivity UV photodetectors.

     

Ultra‐high long‐term stability of oxide‐TTFTs under current stress

In this letter the stability of transparent thin‐film transistors (TTFTs) based on the ZnO–SnO₂ (ZTO) material system is investigated. Bottom‐gate devices have been subject to electrical stress via a gate–source bias of 10 V and a drain‐source bias of 10 V leading to a drain–source current of 188 µA. In optimized TTFTs with a composition of [Zn]:[Sn] = 36:64 the relative change of the saturated field effect mobility was less than 1% and the threshold voltage shift was about 320 mV after 1000 hours of operation. This extraordinary stability of ZTO TTFTs underlines their suitability as drivers in active matrix OLED displays. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

High‐Responsivity Photodetectors Based on Formamidinium Lead Halide Perovskite Quantum Dot–Graphene Hybrid

Highly performance photodetector requires a wide range of responses of the incident photons and converts them to electrical signals efficiently. Here, a photodetector based on formamidinium lead halide perovskite quantum dots (e.g., FAPbBr₃ QDs)–graphene hybrid, aiming to take the both advantages of the two constituents. The FAPbBr₃ QD–graphene layer not only benefits from the high mobility and wide spectral absorption of the graphene material but also from the long charge carrier lifetime and low dark carrier concentration of the FAPbBr₃ QDs. The photodetector based on FAPbBr₃ QD–graphene hybrid exhibits a broad spectral photoresponse ranging from 405 to 980 nm. A photoresponsivity of 1.15 × 10⁵AW⁻¹ and an external quantum efficiency as high as 3.42 × 10⁷% are obtained under an illumination power of 3 µW at 520 nm wavelength. In detail, a high responsivity is achieved in 405–538 nm, while a relatively low but fast response is observed in 538–980 nm. The photoelectric conversion mechanism of this hybrid photodetector is investigated in the view of built‐in electric field from the QD–graphene contact which improves the photoconductive gain.     

The fabrication and characterization of ZnO UV detector

ZnO films were deposited on GaAs substrates by radio frequency (rf) magnetron sputtering followed by an ambient-controlled heat treatment process for arsenic doping. In Hall measurements, the As-doped ZnO films showed the characteristics of p-type semiconductor. The ZnO thin film p–n homojuctions were then fabricated to investigate the electrical properties of the films. The p–n homojunctions exhibited the distinct rectifying current–voltage (I–V) characteristics. The turn-on voltage was measured to be 3.0 V under the forward bias. When ultraviolet (UV) light (λ = 325 nm) was irradiated on the p–n homojunction, photocurrent of 2 mA was detected. Based on these results, it is proposed that the p–n homojunction herein is a potential candidate for UV photodetector and optical devices.     

Chemical synthesis of ZnO hexagonal thin nanodisks and dye‐sensitized solar cell performance

Well defined highly monodispersed single crystalline ZnO hexagonal thin nanodisks have been synthesized by a wet chemical route. Ethylenediaminetetraacetic acid is used as an organic ligand in the chemical synthesis. Ultraviolet near band edge emission is predominant over the defect level emission in these ZnO nanodisks. The ZnO nanodisks have an average diameter of 150 nm and thickness of 40 nm. A dye‐sensitized solar cell is fabricated using ZnO nanodisks by spray pyrolysis deposition and it exhibits an efficiency of 2.63% with the ruthenium sensitizer N719 dye. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

包埋Pt纳米粒子对金属-半导体-金属结构ZnO紫外光电探测器性能的影响

利用射频磁控溅射设备制备ZnO薄膜, 最终制备ZnO/Pt纳米粒子/ZnO 结构的金属-半导体-金属型紫外光电探测器. 研究了Pt纳米粒子处在ZnO薄膜层中的不同深度对金属-半导体-金属型紫外光电探测器响应性能的影响. 结果表明, 探测器的响应度随着Pt纳米粒子在ZnO薄膜层中所处深度的增大而升高. 在60 V偏压下, 包埋Pt最深的探测器在波长365 nm处取得响应度最大值1.4 A·W^-1, 包埋有Pt探测器的响应度最大值为无Pt 纳米粒子探测器响应度最大值的7倍. 结合对ZnO薄膜表面的表征及探测器各项性能的测试, 得出包埋Pt纳米粒子增强器件的响应性能可归因于表面等离子体增强散射.     

InGaAs-MSM光电探测器设计与仿真研究

对基于InGaAs材料体系的金属 半导体 金属（metal semiconductor metal,MSM）光电探测器进行设计,并对其暗电流、光电流、电容以及截止频率等性能参数进行仿真。通过添加InAlAs肖特基势垒增强层,将探测器的暗电流减小到了pA量级。仿真结果表明,探测器在光照下有明显的光响应,通过合理设计器件结构,探测器的工作频率可以达到1.5 THz。制备了探测器样品,并对其暗电流和光响应进行了测试,测试结果与仿真结果基本吻合。     

Double‐layer channel structure based ZnO thin‐film transistor grown by atomic layer deposition

A double channel structure has been used by depositing a thin amorphous‐AlZnO (a‐AZO) layer grown by atomic layer deposition between a ZnO channel and a gate dielectric to enhance the electrical stability. The effect of the a‐AZO layer on the electrical stability of a‐AZO/ZnO thin‐film transistors (TFTs) has been investigated under positive gate bias and temperature stress test. The use of the a‐AZO layer with 5 nm thickness resulted in enhanced subthreshold swing and decreased V_th shift under positive gate bias/temperature stress. In addition, the falling rate of the oxide TFT using a‐AZO/ ZnO double channel had a larger value (0.35 eV/V) than that of pure ZnO TFT (0.24 eV/V). These results suggest that the interface trap density between dielectric and channel was reduced by inserting a‐AZO layer at the interface between the channel and the gate insulator, compared with pure ZnO channel. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Improved performance of silicon‐nanoparticle film‐coated dye‐sensitized solar cells

Silicon (Si) nanoparticles with average size of 13 nm and orange–red luminescence under UV absorption were synthesized using electrochemical etching of silicon wafers. A film of Si nanoparticles with thickness of 0.75 µm to 2.6 µm was coated on the glass (TiO₂ side) of a dye‐sensitized solar cell (DSSC). The cell exhibited nearly 9% enhancement in power conversion efficiency (η) at film thickness of ～2.4 µm under solar irradiation of 100 mW/cm² (AM 1.5) with improved fill factor and short‐circuit current density. This study revealed for the first time that the Si‐nanoparticle film converting UV into visible light and helping in homogeneous irradiation, can be utilized for improving the efficiency of the DSSCs. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Sensitization of ZnO photoconductivity by chemical modification of surface states

Surface States on ZnO have been investigated through their effect on photoconductivity. Low energy photons (0·7 ～ 1·5 eV) are found to induce a feeble photocurrent in ZnO which is attributable to the direct electron injection from surface levels to the conduction band. A definite correlation has been found between the i.r. induced photocurrent and the intrinsic or the dye sensitized photocurrent excited by UV or visible radiation. It is proposed that phthalic anhydride on ZnO modifies the distribution of surface levels, by a chemical interaction with chemisorbed oxygen. Surface levels originating in chemisorbed oxygen ions are transformed by phthalic anhydride into new levels which are shallower but thermally more stable. These traps are found to enhance the photoconductivity of ZnO. The chemical nature of them and the mechanism of sensitization are discussed.