纳米固体酸催化合成无毒增塑剂柠檬酸三辛酯的研究

以柠檬酸和正辛醇为原料,采用自制的纳米固体酸S04^2-／SnO2、SO4^2-／ZrO2、SO4^2-／TiO2及SO4^2-／Fe2O3催化剂合成无毒增塑剂柠檬酸三辛酯（trioctylcitrate,TOC）。分别考察了纳米催化剂种类、催化剂用量、醇／酸物质的量比、反应时间、反应温度等因素对合成TOC反应酯化率的影响,对合成的产品进行红外光谱分析。实验结果表明,自制的固体酸SO4^2-／SnO2催化合成无毒增塑剂柠檬酸三辛酯的最佳反应条件：催化剂用量为1．0g,酸醇比为1：6.3,反应时间1．0h,反应温度190℃。在最佳反应条件下,柠檬酸三辛酯的酯化率可达到98．5％。     

环保增塑剂柠檬酸三(2-乙基)己酯的合成

以柠檬酸和2-乙基己醇为原料,用结晶硫酸高铈为催化剂合成环保增塑剂柠檬酸三(2-乙基)己酯,考察了反应温度、催化剂用量、醇酸摩尔比、反应时间等因素对反应结果的影响,对合成的产品进行了红外光谱分析。实验结果表明,硫酸高铈催化合成柠檬酸三(2-乙基)己酯的最佳反应条件为n(2-乙基已醇)∶n(柠檬酸)=3.60∶1,催化剂用量为柠檬酸质量的1.5%,反应时间为90 m in,反应温度为150℃~160℃,在最佳反应条件下,柠檬酸三(2-乙基)己酯收率在98%以上。     

介孔分子筛P-SBA-1催化合成柠檬酸三丁酯

采用后合成法制备了介孔分子筛催化剂P-SBA-1,并用XRD和SEM对催化剂进行分析,表征结果表明催化剂P-SBA-1具有立方结构(空间点群Pm3n)。选用液体酸H2SO4和微孔分子筛HY、ZSM-5与SBA-1进行对比,结果表明催化剂的活性高低顺序为:H2SO4SBA-1HYZSM-5。将改性后的介孔分子筛P-SBA-1作为固体酸催化剂合成柠檬酸三丁酯。重点考察了催化剂用量、酸醇摩尔比、反应温度、反应时间等因素以及催化剂的重复使用性能。结果表明P-SBA-1催化合成柠檬酸三丁酯的最佳条件为:反应温度140℃,酸醇摩尔比1∶6,催化剂用量为反应物总质量的1.5%,反应时间5h。催化剂P-SBA-1重复使用性能良好。     

固载杂多酸SiW_(12)/C催化合成富马酸二甲酯

用自制的固体杂多酸催化剂SiW12 /C进行催化酯化合成富马酸二甲酯 (DMF) .探讨了催化剂用量、醇 /酸比、反应时间、反应温度等动力学条件对合成DMF的影响 .确定了合成DMF的最佳合成工艺条件 :醇 /酸物质的量比为 6∶1,催化剂用量为富马酸质量的 2 .5 % ,反应时间 7.0h ,反应温度为回流温度 ,酯化率可达 90 .6 % .结果表明 ,该催化剂催化活性高 ,可重复使用 ,后处理容易 ,生产成本低且无三废污染 .     

乙酸异戊酯的合成

以乙酸和异戊醇作为原料,利用SnCl4催化作用下的酯化反应合成了乙酸异戊酯;研究了反应时间、酸醇的物质的量之比、催化剂用量、带水剂用量等因素对产物收率的影响,并确定了优化反应条件.结果表明,优化反应条件为:反应时间60min,酸醇物质的量之比1∶0.8(乙酸5.76mL),催化剂用量0.35g,带水剂用量10mL.在优化反应条件下,产物收率最高可达86.3%.     

固体超强酸SO4/ZnO-TiO2催化合成柠檬酸三丁酯

以固体超强酸SO4/ZnO-TiO2作催化剂,柠檬酸、正丁醇为原料合成了柠檬酸三丁酯(TBC).考察了反应条件对酯化率的影响.结果表明,固体超强酸SO4/ZnO-TiO2是合成柠檬酸三丁酯的良好催化剂,最佳反应条件为:正丁醇和柠檬酸的摩尔比为4.0:1,反应温度130℃-140℃,反应时间2.5h,催化剂用量为柠檬酸质...     

二氧化硅负载硫酸氢钠催化合成壬酸乙二醇单酯

研究了以二氧化硅负载硫酸氢钠为催化剂,壬酸和乙二醇为原料合成壬酸乙二醇单酯的工艺.考察了酸醇物质的量、催化剂用量、反应时间、反应温度等对壬酸酯化率的影响,结果表明,合成壬酸乙二醇单酯的优化条件为:壬酸与乙二醇的物质的量为1∶3,催化剂的用量为反应物料总质量的5%,反应时间为4h,反应温度为90℃,在此条件下,酯化率可达92%以上,通过红外光谱验证了目标产物.催化剂具有一定的重复使用活性.     

硅烷偶联剂改性SBA-15固载Keggin型杂多酸催化合成柠檬酸三丁酯

以3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MEMO)表面改性的介孔分子筛SBA-15为载体,制备了一系列介孔分子筛/硅烷偶联剂@杂多酸复合催化剂SBA-15/MEMO@HnXW12O40(X=P⁵+,Si⁴⁺,B³⁺;n=3,4,5),并利用FTIR、P-XRD、TEM、N2吸附-脱附对其结构进行表征。以SBA-15/MEMO@HnXW12O40(X=P⁵⁺,Si⁴⁺,B³⁺;n=3,4,5)为负载型杂多酸催化剂对柠檬酸三丁酯的催化合成进行研究,分别考察了酸醇摩尔比、催化剂用量、反应温度、反应时间对催化合成柠檬酸三丁酯酯化率的影响,并获得合成柠檬酸三丁酯的最佳工艺条件。结果表明:当负载型硅钨酸催化剂的负载量为50%、催化剂用量为3.8%、酸醇摩尔比为1∶4、反应温度为140℃、反应时间为6 h、环己烷用量为5 mL时酯化率可达97.56%,重复使用7次后酯化率仍可达62.67%。     

乙酸异丙酯的合成

以乙酸和异丙醇为原料,硫酸氢钠为催化剂,合成了乙酸异丙酯;考察了反应时间、酸醇比、催化剂用量、带水剂用量对酯化率的影响,确定了最佳酯化反应条件:反应时间60min,酸醇的物质的量的比1∶0.8,催化剂用量0.8g,带水剂用量8mL.在最佳反应条件下,酯化率最高可达84.3%.     

废动植物油脂制备烷醇酰胺的研究

以废动植物油脂为原料,在自制DYD催化剂作用下制得脂肪酸甲酯,再以氢氧化钾为催化剂,与二乙醇胺合成烷醇酰胺。考察了反应温度、反应时间、催化剂用量、真空度等因素对反应的影响,通过单因素实验和析因实验确定最佳工艺条件为:甲酯/二乙醇胺物质的量比1∶1.55,反应温度110℃,反应时间2.5 h,真空度0.08 MPa,催化剂用量0.65%(相对于脂肪酸甲酯的质量),烷醇酰胺的收率达96.3%。通过红外光谱对产物结构进行了表征,并对界面张力进行了测定。结果表明,产物具有较好的界面活性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).