Analysis of PAH compounds in soil with on-line coupled pressurised hot water extraction–microporous membrane liquid–liquid extraction–gas chromatography

Pressurised hot water extraction (PHWE) was coupled on-line with microporous membrane liquid-liquid extraction (MMLLE) and gas chromatography (GC) in the analysis of polycyclic aromatic hydrocarbon (PAH) compounds in soil. The MMLLE serves as a trapping device after the PHWE. Water from PHWE is directed to the donor side of the membrane unit and the analytes are extracted to the acceptor solution on the other side of the membrane. The role of MMLLE is to clean and concentrate the extract, which is then transferred on-line to the GC via a sample loop and an on-column interface using partially concurrent solvent evaporation. Separate optimisation of MMLLE and simulations of the PHWE-MMLLE connection were carried out before the actual on-line coupling. After optimisation of the whole on-line system, the efficiencies of the PHWE-MMLLE-GC and PHWE-solid-phase trap extractions were compared. The PHWE-MMLLE-GC method allowed on-line analysis of soil samples. The method was linear, with limits of detection in the range 0.05-0.13 ng and limits of quantification 0.65-1.66 microg g(-1). Comparison of the results with those obtained by other techniques confirmed the good performance.     

Pressurised hot water extraction coupled on-line with liquid chromatography-gas chromatography for the determination of brominated flame retardants in sediment samples

Pressurised hot water extraction (PHWE) was coupled on-line with liquid chromatography-gas chromatography (LC-GC) to determine brominated flame retardants in sediment samples. After extraction with pressurised hot water the analytes were adsorbed in a solid-phase trap. The trap was dried with nitrogen and the analytes were eluted to the LC column, where the extract was cleaned, concentrated and fractionated before transfer to the GC system. The fraction containing the brominated flame retardants was transferred to the GC system via an on-column interface. The PHWE-LC-GC method was linear from 0.0125 to 2.5 microg with limits of detection in the range 0.70-1.41 ng/g and limits of quantification 6.16-12.33 ng/g.     

Pressurised hot water extraction-microporous membrane liquid-liquid extraction coupled on-line with gas chromatography-mass spectrometry in the analysis of pesticides in grapes

Pressurised hot water extraction-microporous membrane liquid-liquid extraction was coupled on-line with gas chromatography-mass spectrometry (PHWE-MMLLE-GC-MS) for the analysis of pesticides in grapes. MMLLE serves as a trapping step after PHWE. Water from PHWE is directed to the donor side of the membrane unit and the analytes are extracted to the acceptor solution on the other side. The role of MMLLE is to clean and concentrate the extract before on-line transfer to the GC via a sample loop and an on-column interface using partially concurrent solvent evaporation. The extraction conditions were investigated, and then the quantitative features such as linearity, limit of quantification (LOQ), extraction yield and enrichment factors. LOQs in the range 0.3-1.8 microg kg(-1) were achieved. Procymidone and tetradifon were found in the skins of the grapes. The results were in good agreement with those obtained by liquid-solid and ultrasonic extractions.     

Ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to gas chromatography-mass detection

Continuous ultrasound-assisted extraction of nitropolycyclic aromatic hydrocarbons from soil prior to their individual separation and determination by gas chromatography (GC) with MS-MS detection is presented here. A multivariate optimisation of the variables affecting the continuous extraction step (namely, probe position, ultrasound radiation amplitude, percentage of duty cycle of ultrasonic exposure, sonication time, total extractant volume, extractant flow rate and temperature of the water-bath in which the extraction cell was placed) was performed. The method was compared with the reference EPA method 3540 using natural contaminated soils. Similar efficiencies were obtained but with a drastic reduction of both the extraction time (10 min versus 24 h) and the extractant volume (less than 10 ml versus 100 ml) by the proposed method. Detection limits of low picogram were obtained, with repeatability and reproducibility between 4.21-5.70 and 5.20-7.23%, respectively.     

Comparison of methods for quantitative analysis of additives in low-density polyethylene using supercritical fluid and enhanced solvent extraction.

On-line supercritical fluid extraction-supercritical fluid chromatography (SFE-SFC) with cryogenic trapping was used to extract and separate five additives from a low-density polyethylene (LDPE) sample. A glass tube filled with glass wool afforded excellent collection efficiency for the extracted analytes. Additive spiked sand was employed to optimize the various parameters of the on-line SFE-SFC system. Calibration curves from the spiked sand studies for on-line SFE-SFC were obtained with good linearities for quantitation. Results obtained on additives in LDPE from on-line SFE-SFC were comparable to those from off-line SFE-HPLC and off-line enhanced solvent extraction (ESE)-HPLC for all additives except Irganox 1076. However, the precision obtained with on-line SFE-SFC was lower than that from off-line SFE-HPLC and off-line ESE-HPLC due to the small sample size employed in the on-line system. Considerable clean-up of the ESE extract was required prior to chromatographic analysis. On-line SFE-SFC minimized the sample handling and eliminated the use of organic solvent. Despite the lower than expected precision, the on-line SFE-SFC method for quantitation of polymer additives appears to be reliable and robust for application in routine quality control analysis.     

Determination of 39 polybrominated diphenyl ether congeners in sediment samples using fast selective pressurized liquid extraction and purification

In order to reduce time of analysis, a new pressurized liquid extraction (PLE) method that automatically and rapidly achieves quantitative and selective extraction of 39 polybrominated diphenyl ether (PBDE) congeners in sediment samples was optimized. It consists of on-line cleanup by inclusion of sorbents in the extraction cell. The new method was compared with a conventional method based on the use of Soxhlet extraction followed by solid-phase extraction (SPE) with cartridges. The instrumental determination was performed by GC-MS, using negative chemical ionization in the selected-ion monitoring mode. Recoveries from 47 to 82% were obtained for spiked tri- to hepta-PBDE congeners in sediment sample. The repeatability of replicate extractions was better than 15% relative standard deviation. The detection limits obtained with the new developed method were between 1 and 46 pg/g dry weight. The reduction in the sample preparation (extraction + cleanup) time (from days to 30 min) with a similar efficiency than that afforded by the conventional Soxhlet extraction-SPE cleanup technique indicates the suitability of this method. The method was applied to sediment samples where the analytes were detected in the range of 0.86-2.49 ng/g dry mass.     

Preparation and evaluation of solid-phase microextraction fibers based on monolithic molecularly imprinted polymers for selective extraction of diacetylmorphine and analogous compounds

All of the studies on solid-phase microextraction based on molecularly imprinted polymers up to now have been carried out on the synthesis of the polymer on the surface of the fiber which is brittle and the polymer coating strips during handling. The objective of this study was to develop a method for fabrication of a monolithic and robust solid-phase microextraction fiber on the basis of molecularly imprinted polymer for selective extraction of diacetylmorphine and its structural analogues followed by their GC or GC/MS analysis. A fiber was produced by copolymerization of methacrylic acid-ethylene glycol dimethacrylate imprinted with diacetylmorphine. The effective factors influencing the polymerization have been investigated and are detailed here. Also, the influences of pH, extraction time and temperature on the extraction efficiency of analytes were investigated. The prepared fiber was thermally stable up to 300 degrees C which has vital importance in SPME coupled with GC or GC/MS. The adsorption isotherm modeling was performed by fitting the data of studied compounds to bi-Langmuir isotherm model. The evaluated equilibrium constants for diacetylmorphine were 0.011 and 1824.72 microM(-1), and the number of binding sites was 170.37 and 4.64 nmolg(-1), respectively. This fiber was successfully used for extraction of template molecule from aqueous solution and further analysis with GC or GC/MS. The high extraction efficiency was obtained for diacetylmorphine, 6-monoacetylcodeine, and 6-monoacetylmorphine, yielding the detection limits of 300, 47, and 1 ngmL(-1), respectively.     

On-line coupling of subcritical water extraction with high-performance liquid chromatography via solid-phase trapping

Although ambient water is very polar and cannot dissolve many organic species, water at elevated temperatures behaves like a polar organic solvent. Thus, subcritical water has been proven to be an effective extraction fluid for several classes of organic compounds. While solvent trapping was used to collect the extracted analytes in most of previous subcritical water extractions, sorbent trapping has also been developed for subcritical water extraction. In this study, an on-line system for subcritical water extraction and high-performance liquid chromatography (HPLC) was built and tested. A sorbent trap was used as the interface between subcritical water extraction and HPLC. Several shut-off valves have been utilized to switch the system from one mode to another (e.g., from the extraction mode to HPLC mode). The coupling technique of subcritical water extraction and HPLC eliminates the liquid-liquid extraction used in solvent trapping subcritical water extraction and provides higher sensitivity. Compared to the off-line system reported in an earlier work, the operation of this on-line system is even easier. Some peak broadening occurred after the coupling the water extraction with HPLC for the analytes studied. The performance of this on-line system was evaluated by the extraction and determination of caffeine, nitrotoluenes, polychlorinated biphenyls, chlorophenols and anilines.     

Automatic sample preparation of sulfonamide antibiotic residues in chicken breast muscle by using dynamic microwave-assisted extraction coupled with solid-phase extraction

In the work, a rapid, simple and high-throughput sample preparation method was developed for the determination of sulfonamide (SA) antibiotic residues in chicken breast muscle. The extraction and clean-up were online combined and up to 20 samples can be treated simultaneously in 6 min. The SAs were first extracted with acetonitrile under the action of microwave energy, and then the extract was directly introduced into the SPE column for on-line clean-up and concentration. Subsequently, the SAs eluted from the SPE column were determined by liquid chromatography-tandem mass spectrometry. The precisions of extraction results of 20 samples were in the range of 4.9-7.4%. The limits of detection and quantification obtained were in the range of 2.4-3.6 ng/g and 8.6-11.3 ng/g for SAs, respectively. The recoveries of SAs obtained by analyzing chicken muscles at three fortified levels (10, 50 and 500 ng/g) were in the range of 82.6-93.2%. The results of the validation process prove that the proposed method is suitable for treating numbers of complex samples simultaneously in a short time.     

An efficient and fast microwave-assisted extraction method developed for the simultaneous determination of 18 organochlorine pesticides in sediment

An efficient and fast microwave-assisted extraction (MAE) method followed by gas chromatographic separation with mass spectrometric detection (GC–MS) was developed for the extraction of 18 organochlorine pesticides (OCPs) from sediment. Parameters affecting the MAE procedure such as the type and volume of the extraction solvent, irradiation power, temperature and irradiation time were successfully optimised. Under the optimal conditions, extraction efficiencies in the range of 73.4–119% were obtained with THF–HEX (9:1, v/v) for all OCPs studied. The method was linear over the range of 2.9–5000 ng g^?1 with determination coefficients (r²) higher than 0.992 for all analytes. The limits of detection, LODs (S/N = 3), obtained varied from 1.0 to 2.2 ng g^?1 and limits of quantification, LOQs (S/N = 10) were between 2.9 and 6.8 ng g^?1. The proposed method was successfully applied to the analysis of real sediment samples and acceptable recoveries from 70.1 to 124% with RSDs ≤14.8% were obtained. 10 OCPs were determined below their LOQ and 8 OCPs in the range of 124–2830 ng g^?1. The MAE method was compared with Soxhlet, shake flask and ultrasonic solvent extraction techniques. Thus, the MAE–GC–MS method could efficiently be used for selective extraction and quantification of the target analytes from the complex sediment matrices.     

Determination of dichlorvos by on-line microwave-assisted extraction coupled to headspace solid-phase microextraction and gas chromatography-electron-capture detection

The pretreatment technique of microwave-assisted extraction on-line headspace solid-phase microextraction (MAE-HS-SPME) was designed and studied for one-step in-situ sample preparation prior to the chromatographic analysis of a pesticide on vegetables. The pesticide on chopped vegetables was extracted into an aqueous solution with the aid of microwave irradiation and then directly onto the SPME fiber in headspace. After being collected on to the SPME fiber and desorbed in the GC injection port, the pesticide (dichlorvos) was analyzed with a GC-electron-capture detection system. The optimum conditions for obtaining extraction efficiency, such as the pH, the polarity modifier, and the salt added in sample solution, the microwave irradiation, as well as the desorption parameters were investigated. Experimental results indicated that the proposed MAE-HS-SPME technique attained the best extraction efficiency of 106% recovery under the optimized conditions, i.e. irradiation of extraction solution (10% aqueous ethylene glycol) at pH 5.0 with medium microwave power for 10 min. Desorption at 220 degrees C for 3 min offered the best detection result. The detection was linear at 5-75 microg/l with correlation coefficient of 0.9985. Detection limit was obtained at approximately 1.0 microg/l level based on S/N=3. The proposed method provided a very simple, fast, and solvent-less procedure to collect pesticides directly from vegetables for GC determination. Its application was illustrated by the analysis of trace dichlorvos in vegetables.     

Determination of pentachlorophenol and tribromophenol in sawdust by ultrasound-assisted extraction and MEKC

An ultrasonic bar-assisted extraction and CE separation procedure for the determination of pentachlorophenol (PCP) and 2,4,6-tribromophenol (TBP) residues in sawdust was developed and applied. For this purpose, micellar electrokinetic capillary chromatography (MEKC) was used and compared with a GC/MS methodology. This methodology allowed the quantification of PCP and TBP in a concentration range of 2.5-12.0 mg/kg for TBP and 2.8-12.0 mg/kg for PCP. Different sample treatment processes were evaluated in order to extract these compounds from sawdust. Better results were obtained when the residues were extracted with ultrasound-assisted hexane, filtered, evaporated, dissolved in Na(2)CO(3), and injected into the CE equipment. The optimal option for GC/MS was extraction with Na(2)CO(3 )followed by a derivation using acetic anhydride and liquid-liquid extraction with hexane. This method allowed the quantification of TBP and PCP in sawdust in a concentration range of 0.19-12.00 mg/kg and 0.14-12.00 mg/kg, respectively. The CE method was compared with the GC/MS as reference method. The results were shown to be statistically similar by both methods for PCP as well as for TBP.     

Ultrasonic nebulization extraction coupled with on-line gas chromatography for determination of trans-anethole in spices

Ultrasonic nebulization extraction (UNE) coupled with on-line gas chromatography (GC) was proposed for the determination of trans-anethole in fruits of Illicium verum Hook. f. and Foeniculum vulgare Mill. The extraction was performed in a common self-made extraction system. In the UNE the analyte was transferred and enriched from the solid sample to gas phase. The sample gas containing analyte obtained by UNE was introduced into the sampling loop with the purging gas (N₂). And then the sample gas in the sampling loop was introduced into the GC column. Several experimental parameters of on-line UNE-GC, including sampling time, flow rate of purging gas, standstill time and temperature of tubing, were optimized. The calibration curve ranging from 0.05 to 1.5 mg g⁻¹ for determining the trans-anethole was obtained. The recoveries for determining trans-anethole are between 99.2% and 111.2% and RSDs are less than 8.3% when the UNE was applied. The analytes can rapidly be extracted and transferred from the solid sample to gas phase. The analytes in the gas phase are easier to be introduced into GC system than those in the solid and liquid phase. Compared with off-line systems, the proposed on-line system is more suitable to detect volatile compounds.     

Automated analysis of polar pesticides in water by on-line solid phase extraction and gas chromatography using the co-solvent effect

In order to meet the requirements of analyzing very low concentrations of pesticides in water (typically at 0.1 μg/l or less), samples have to be concentrated prior to GC-analysis. Samplie pre-concentration by off-line methods based on solid phase extraction (SPE) or liquid-liquid extraction are very time consuming and cumbersome. Moreover, the quantitative performance of the analytical method as a whole in terms of accuracy and reliability is seriously hindered by elaborate, manually performed sample pre-treatment steps. This paper describes an automated method based on solid phase extraction and capillary gas chromatography. The technique was applied for the analysis of 31 polar organophosphorus and organonitrogen pesticides. A commercially available HPLC/GC instrument is modified, using the LC-part for solid phase extraction. The sample, of which only a few ml's is required to obtain sufficiently low detection limits, is delivered by a robotic large volume autosampler. After solid phase extraction and elution, the eluate is transferred into the GC via a so called “loop type interface”. In this paper the instrumentation and analytical methodology is described, as well as the main validation results. The quantitative performance (i.e. recovery and repeatability) of the most polar solutes like metamitron and dimethoate appears to be better than obtained with off-line SPE as a result of the more beneficial ratio between the amount of sorbent and the sample volume. As the loop-type interface causes losses of the most volatile compounds, a co-solvent is added. This co-solvent provides sufficient trapping capacity in the capillary pre-columns to allow quantitative analysis of even the most volatile pesticides. Moreover a better separation of early eluting compounds is also established.     

Determination of N-methylcarbamate pesticides in environmental samples by an automated solid-phase extraction and liquid chromatographic method based on post-column photolysis and chemiluminescence detection

An automated solid-phase extraction-high performance liquid chromatography method has been developed to determine trace concentration of N-methylcarbamate pesticides in water and fruits. The method is based on the post-column conversion of the pesticides into methylamine by irradiation with UV light. The resultant methylamine was subsequently detected by chemiluminescence using tris(2,2'-bipyridyl)ruthenium(III), which was on-line generated by photo-oxidation of the ruthenium(II) complex with peroxydisulfate. Factors affecting the rate of the reactions were optimized so that their contribution to the total band-broadening was negligible. This detection system was used to determine bendiocarb, carbaryl, promecarb and propoxur, which were separated on an ODS C(18) column. The mobile phase consisted of water and acetonitrile using a gradient elution. A linear relationship between peak area and concentration was obtained for all pesticides (r(2)>0.999). Intra- and inter-day precision values of about 0.64-1.3% RSD (n=10) and 2.2-2.8% RSD (n=15), respectively, were obtained. N-Methylcarbamate pesticide residues at ultratrace levels could be determined in environmental samples when an automated solid-phase extraction device was coupled on-line with the HPLC system. Detection limits were within the range 3.9-36.7 ngl(-1) for water samples and 0.5-4.7 microgkg(-1) for fruits.     

Rapid multiresidue extraction method of organochlorinated pesticides from fish feed

A rapid multiresidue extraction method for organochlorinated pesticides from fish feed was developed, which is based on the extracted fat treatment by n-hexane, concentrated sulphuric acid and ENVI-carb, a graphitized non-porous carbon material. The final residue, obtained in about 50 min, was dissolved in isooctane and analysed by gas chromatography with an electron capture detector (GC/ECD). The presence of the extracted pesticides was confirmed by gas chromatography-mass spectrometry (GC/MS). Concentration of sulphuric acid and amount of ENVI-carb were optimized in order to improve analytes recovery, accuracy and detection limits. This simple and relatively fast method allowed a high recovery of the HCB, Lindane, HEPO, p,p'-DDE, p,p'-DDD, p,p'-DDT residues, with mean values in the range 68-124% at four fortification levels (12.5, 25.0, 50.0, 100.0 ng/g), and coefficients of variation between 1.9 and 20.2%. Detection limit were equal to 3.0 ng/g, related to fat, for all pesticides, and calibration curves were linear (r > 0.999) in the range of explored concentrations from the detection limit to 100 ng/g. For all pesticides a good repeatability was obtained (CV% values in the range 0.23-4.16%) when a sequence of six injections of the isooctane extraction solution was performed. The usefulness of the proposed method has been tested by the analysis of fish feed samples.     

Development and validation of a method using on-line solid-phase extraction and liquid chromatography with ultraviolet detection for the determination of bisphenol A, octylphenol, and nonylphenol in groundwater

Alkylphenols are nonbiodegradable metabolites arising from various pathways of aerobic and anaerobic degradation of the nonionic surfactants alkylphenol ethoxylates. A method based on the use of on-line solid-phase extraction (SPE) and liquid chromatography (LC) with UV detection was developed to determine bisphenol A, octylphenol, and nonylphenol at trace levels in water. The on-line coupled SPE procedure automatically enables an approximately 300-fold preconcentration of analytes, which can be further enhanced by an increase in applied sample volume. By using C18 cartridges, recoveries of >90% were obtained for all the analytes. A validation procedure was carried out with a groundwater sample to ensure the quality of the results; performance criteria such as detection limits (LODs), quantitation limits (LOQs), linearity, and precision were evaluated. LODs and LOQs in the range of 0.17-0.36 and 0.35-1.88 microg/L, respectively, were found; for all the analytes, linearity was established over 2 orders of magnitude (r2 >0.997, n = 54). The intraday repeatability values expressed as relative standard deviations were <5.3%; a nested analysis of variance was performed to verify the influence of 3 different factors, i.e., different days, extraction procedure, and LC replicate injection, on data precision.     

Speciation of Fe(II) and Fe(III) by the modified ferrozine method,FIA-spectrophotometry,and flame AAS after cloud-point extraction

A method has been developed for the simultaneous determination of traces of Fe(III) and Fe(II) in water by on-line coupling of spectrophotometry with flame atomic absorption spectrometry (FAAS). The method involves cloud-point extraction (CPE) of both species with ammonium pyrrolidinecarbodithioate (APDC) under standard conditions, which facilitates the in situ complexation and extraction of both species. Differentiation of the oxidation states of iron is achieved by using mathematical equations to overcome the interference of Fe(III) in the spectrophotometric determination of Fe(II) when they are both present in the same solution. In this manner the time-consuming and labor-intensive steps of preoxidation of Fe(II) or reduction of Fe(III) are eliminated. By preconcentrating a 10-mL sample solution detection limits as low as 7 microg L(-1), were obtained after a single-step extraction procedure. The relative standard deviation (n=4, 30 microg L(-1)) was 2.6 % and 1.8 % for spectrophotometry and FAAS, respectively. Recoveries in the range of 96-105 % were obtained by analysis of spiked real samples. The method was further verified by analyzing a certified reference material (IMEP-9); for this the recovery was 98.5 %.     

Determination of polychlorinated biphenyls in biota samples using simultaneous pressurized liquid extraction and purification

In order to reduce time and cost of analysis, a new pressurised liquid extraction method that automatically and rapidly achieves quantitative and selective (i.e., lipid-free) extraction of polychlorinated biphenyls (PCBs) in biota tissues was optimized. It consists of on-line clean-up by inclusion of sorbents in the extraction cell. The freeze-dried sample is dispersed with Florisil and loaded in the extraction cell containing an extra amount of Florisil. The extraction is performed under mild conditions using 55 ml of a dichloromethane-pentane (15:85) mixture, a temperature of 40 degrees C, a static extraction time of 10 min and two extraction cycles. The Florisil retains coextracted lipids from the matrix, and the extract, after pre-concentration, is clean enough for direct injection into GC-MS and GC-electron-capture detection (ECD). Quantitative recoveries (from 90 to 106%) are obtained for both native and spiked PCB congeners in samples with a high lipidic content (up to 42% dry mass, in spoonbill eggs). The reproducibility of replicate extractions was better than 11% relative standard deviation. Method detection limits were in the ranges of 0.001-0.004 and 0.002-0.07 ng g(-1) dry mass for GC-ECD and GC-MS-MS, respectively. The method was validated using the standard reference material SRM 2974 (a mussel tissue) from the US National Institute of Standards and Technology, compared to Soxhlet and matrix solid-phase dispersion extraction methods, and used to evaluate the contamination by PCBs in bivalves from South of Spain.     

在线固相萃取净化-液相色谱-串联质谱法测定猪肉中10种大环内酯类抗生素

建立了在线固相萃取净化-液相色谱-串联质谱检测猪肉中10种大环内酯类抗生素残留的方法。样品经过乙腈提取,提取液40℃旋蒸至干后,分析物用2 mL磷酸盐缓冲液溶解,溶解液经在线固相萃取柱(HLB柱)富集净化,甲醇洗脱,然后转移至XBridge BEH C18色谱柱上,以10 mmol/L乙酸铵水溶液和乙腈溶液为流动相进行分离,最后用串联四极杆质谱检测。结果表明,10种大环内酯类抗生素在0.1~200μg/L范围内呈现良好的线性关系,相关系数均大于0.990。方法的检出限范围为0.05~0.30μg/kg,定量限范围为0.10~1.00μg/kg;添加水平为0.10~10.0μg/kg时,方法回收率为69.6%~115.2%,相对标准偏差(RSD)10%。该方法可以作为猪肉中大环内酯类抗生素的检测方法。