Enhanced directional thermal conductivity of polylactic acid/polybutylene adipate terephthalate ternary composite filled with oriented and surface treated boron nitride

A combination of solution casting and melt extrusion technique was used to fabricate Boron nitride (BN)-filled Polylactic acid (PLA)/polybutylene adipate terephthalate (PBAT) blend composites. The BN particles were surface treated with a silane coupling agent and functionalization was confirmed via spectroscopic analysis. Field emission scanning electron microscopy confirmed that the BN surface treatment improved the particle adhesion with the polymer matrices and acted as a compatibilizer for the polymers. Moreover, changes in the particle orientation in the blend composite yielded improved thermal conductivity in different directions. The inclusion of the treated BN particles enhanced the in-plane (~1.1 W m⁻¹K⁻¹) and through-plane (~0.8 W m⁻¹K⁻¹) thermal conductivity of the composites as compared to the neat PLA. In addition, the storage modulus of the composite become more than 3 GPa that is twice that of the PLA/PBAT blend with a reasonable tensile property. In general, compared with the PLA/PBAT blend, the blend composites exhibited superior thermal and mechanical properties.     

Eco‐friendly conductive polymer nanocomposites (CPC) for solar absorbers design

To reduce both the cost and the environmental impact of copper‐based thermal solar absorbers, we have investigated their possible substitution by bio‐based conductive polymer nanocomposite (CPC) elements. Our results show that carbon nanotubes (CNT) have no significant influence on polymers’ calorimetric properties such as T_m and T_g but lead to a strong increase in crystallinity of poly(lactic acid) (PLA) and to a lesser extent of poly(amide 12) poly(amide 12) (PA12) for 2 and 3 CNT wt % respectively. Percolation thresholds as low as 0.5 and 0.58 were obtained for PA12 and PLA, respectively, and visco‐elastic properties such as η*, G’ and G” were found to increase exponentially with CNT content confirming the formation of a CNT network within the matrix. All CPC are absorbing more energy in the visible and infrared than in the ultraviolet wavelength ranges. Finally, the thermal conductivity k of PLA–CNT and PA12–CNT were increased, respectively, of 85% and 24%, to reach 0.28 W.m^?1.K^?1 and 0.26 W.m^?1.K^?1, for only 5 wt% CNT. The figure of merit suggests that PA12 is the polymer which satisfies at best all criteria, particularly combining a lower viscosity at almost equivalent thermal conductivity and absorptivity. Copyright © 2013 John Wiley & Sons, Ltd.     

Fast and Minimal‐Solvent Production of Superinsulating Silica Aerogel Granulate

With their low thermal conductivity (λ ), silica aerogels can reduce carbon emissions from heating and cooling demands, but their widespread adoption is limited by the high production cost. A one‐pot synthesis for silica aerogel granulate is presented that drastically reduces solvent use, production time, and global warming potential. The inclusion of the hydrophobization agent prior to gelation with a post‐gelation activation step, enables a complete production cycle of less than four hours at the lab scale for a solvent use close to the theoretical minimum, and limits the global warming potential. Importantly, the one‐pot aerogel granulate retains the exceptional properties associated with silica aerogel, mostly λ =14.4±1.0 mW m⁻¹⋅K⁻¹ for the pilot scale materials, about half that of standing air (26 mW m⁻¹⋅K⁻¹). The resource‐, time‐, and cost‐effective production will allow silica aerogels to break out of its niche into the mainstream building and industrial insulation markets.     

Preparation of nylon MXD6/EG/CNTs ternary composites with excellent thermal conductivity and electromagnetic interference shielding effectiveness

In this article,hybrid fillers with different dimensions,namely,2-dimensional (2-D) expanded graphite (EG) and 1-dimensional (1-D) multi-walled carbon nanotubes (CNTs),were added to aromatic nylon MXD6 matrix via melt-blending,to enhance its thermal and electrical conductivity as well as electromagnetic interference shielding effectiveness (EMI SE).For ternary composites of MXD6/EG/CNTs,the electrical conductivity reaches up nine orders of magnitude higher compared to that of the neat MXD6 sample,which tumed the polymer-based composites from an insulator to a conductor,and the thermal conductivity has been enhanced by 477％ compared with that of neat MXD6 sample.Meanwhile,the EMI SE of ternary composite reaches ～50 dB at the overall filler loading of only 18 wt％.This work can provide guidance for the preparation of polymer composites with excellent thermal and electrical conductivity via using hybrid filler.     

Achieving a high thermal conductivity for segregated BN/PLA composites via hydrogen bonding regulation through cellulose network

Normally, the effective dispersion of thermal conductive fillers is a prerequisite for ensuring thermally conductive networks formed in polymer composites. In this work, a facile method was provided by using cellulose to alter the distribution state of boron nitride (BN) for the preparation of high thermally conductive polylactic acid (PLA). After powder mixing and hot‐pressing process, the Cellulose@BN was located at the boundaries of PLA granules to form consecutive thermally conductive networks with more compact structure. Morphology observation and FTIR spectra confirmed that BN edges absorbed on the cellulose surface under the intermolecular hydrogen bond interaction between PLA and BN. At the BN content of 25 wt%, contrasted with traditional BN/PLA segregated polymer composites (SPCs), thermal conductivity coefficient of Cellulose@BN/PLA SPCs improved by 53.5% from 0.71 to 1.09 Wm^?1 K^?1. This enhancement could be attributed to the reason that the cellulose regulated stripe aggregation allowed the BN connect with each other more compact, thus a thermal conduction networks with reduced phonon scattering were formed.     

Effect of aspect ratio of vertically aligned copper nanowires in the presence of cellulose nanofibers on the thermal conductivity of epoxy composites

The composites comprising vertically aligned network of copper nanowires (CuNWs) in the presence of cellulose nanofibers were fabricated by using the freeze‐templating method and the effect of aspect ratio (A/R) of CuNWs on the thermal conductivity of epoxy composites was investigated. The thermal conductivity of epoxy composites increased to 0.79 W m^?1 K^?1 at 1.12 vol% of high A/R CuNWs loading, corresponding to the thermal conductivity enhancement of 365% as compared to the pure epoxy. The thermal conductivity of vertically aligned higher A/R CuNWs/epoxy, which is 38.5% and 51.9% higher than those of the lower A/R CuNWs and the randomly aligned CuNWs, respectively. The application of the epoxy composites in heat dissipation was demonstrated by the temperature changes of composites on a hot plate with the increase of heating time. These results indicate that the thermally conductive composites in this study could be applied for thermal dissipating materials in electronic devices.     

Isothermal crystallization kinetics,morphology, and thermal conductivity of graphene nanoplatelets/polyphenylene sulfide composites

Graphene nanoplatelets (GNP) and polyphenylene sulfide (PPS) were used as filler and matrix, respectively, to produce composites. The PPS/GNP thermal composites were prepared via a melt blending method. The effects of GNP on crystallization behavior and kinetics, morphology, and thermal properties of PPS/GNP composites were investigated. To determine the isothermal crystallization kinetics parameters and isothermal crystallization activation energy, the Avrami model was used to comparatively analyze the relevant DSC experimental data. The results show that GNP provides an obvious heterogeneous nucleation effect on PPS to accelerate the crystallization and decrease isothermal crystallization activation energy. Thermal conductivity values of PPS/GNP composites with various GNP contents revealed that GNP remarkably increases thermal conductivity of composites mainly via a layered dispersion in PPS matrix. Thermal conductivity also increased with increasing GNP content, which was further improved at elevated temperatures. The thermal conductivities of PPS composite containing 30 mass% of GNP were 1.156 and 1.350 W m^?1 K^?1 at 30 and 110 °C, respectively, indicating an increase of more than 3 times compared with the neat PPS.     

Chitosan‐based composite membranes containing chitosan‐coated carbon nanotubes for polymer electrolyte membranes

Considering the poor dispersion and inert ionic conduction ability of carbon nanotubes (CNTs), functionalization of CNTs is a critical issue for their application in polymer electrolyte membranes. Herein, CNTs were functionalized by the polyelectrolyte, chitosan (CS), via a facile noncovalent surface‐deposition method. The obtained CS‐coated CNTs (CS@CNTs) were then incorporated into the CS matrix and fabricated composite membranes. The CS coating can enhance the compatibility between CNTs and the matrix, thus ensuring the homogenous dispersion of CS@CNTs and effectively improved the mechanical properties of the composites. Moreover, the CS coating can make CS@CNTs act as an additional proton‐conducting pathway through the membranes. The CS/CS@CNTs‐1 composite shows the highest proton conductivity of 3.46 × 10⁻² S cm⁻¹ at 80°C, which is about 1.5‐fold of the conductivity of pure CS membrane. Consequently, the single cell equipped with CS/CS@CNTs‐1 membrane exhibits a peak power density of 47.5 mW cm⁻², which is higher than that of pure CS (36.1 mW cm⁻²).     

Solvent-Vapor-Induced Reversible Single-Crystal-to-Single-Crystal Transformation of a Triphosphaazatriangulene-Based Metal–Organic Framework

A triphosphaazatriangulene (H₃L) was synthesized through an intramolecular triple phospha-Friedel–Crafts reaction. The H₃L triangulene contains three phosphinate groups and an extended π-conjugated framework, which enables the stimuli-responsive reversible transformation of [Cu(HL)(DMSO)⋅(MeOH)]_n, a 3D-MOF that exhibits reversible sorption characteristics, into (H₃L⋅0.5 [Cu₂(OH)₄⋅6 H₂O] ⋅4 H₂O), a 1D-columnar assembled proton-conducting material. The hydrophilic nature of the latter resulted in a proton conductivity of 5.5×10⁻³ S cm⁻¹ at 95 % relative humidity and 60 °C.     

A comparative study on the effect of carbon fillers on electrical and thermal conductivity of a cyanate ester resin

Carbon fillers including multi-walled carbon nanotubes (MWCNTs), carbon black (CB) and graphite were introduced in a cyanate ester (CE) resin, respectively. The effects of the fillers on the electrical and thermal conductivity of the resin were measured and analyzed based on the microscopic observations. MWCNTs, CB and graphite exhibited percolation threshold at 0.1 wt%, 0.5 wt% and 10 wt%, respectively. The maximal electrical conductivity of the composites was 1.08 S/cm, 9.94 × 10⁻³ S/cm and 1.70 × 10⁻⁵ S/cm. MWCNTs showed the best enhancement on the electrical conductivity. The thermal behavior of the composites was analyzed by calorimetry method. Incorporation of MWCNTs, CB and graphite increased the thermal conductivity of CE resin by 90%, 15% and 92%, respectively. Theoretical models were introduced to correlate the thermal conductivity of the CE/MWCNTs composite. The interfacial thermal resistance between CE resin and MWCNTs was 8 × 10⁻⁸ m²K/W and the straightness ratio was 0.2. The MWCNTs were seriously entangled and agglomerated. Simulation results revealed that thermal conductivity of the CE/MWCNTs composites can be substantially elevated by increasing the straightness ratio and/or filler content of MWCNTs.     

The effect of a semi‐industrial masterbatch process on the carbon nanotube agglomerates and its influence in the properties of thermoplastic carbon nanotube composites

This study details an industrial process to prepare polypropylene (PP) composites reinforced with different loadings (0.5–10wt.%) of carbon nanotubes (CNTs) from a direct dilution of a masterbatch produced by an optimized extrusion compounding process. The work demonstrates how the anisotropy in the distribution of CNTs can have a positive effect on the electrical conductivity and fracture toughness of the resulting composites. The composite with the highest loading of CNTs had an electrical conductivity of 10^?2 S/m comparable with those reported in the available literature. The composites showed anisotropy in their properties that seems to be caused by the non‐homogeneous distribution of the agglomerates produced by the orientation of the flow direction during the injection process. The composites produced in this work exhibited a fracture toughness up to 55% higher than neat PP and failed by polymer ductile tearing. It was found that the CNT agglomerates distributed throughout the matrix increased the toughness of PP by promoting plastic deformation of the matrix during the fracture process and by a slight load transfer between the polymer matrix and the CNTs of the agglomerates. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 189–197     

Enhancing dielectric and mechanical behaviors of hybrid polymer nanocomposites based on polystyrene,polyaniline and carbon nanotubes coated with polyaniline

The dielectric and mechanical properties of hybrid polymer nanocomposites of polystyrene/polyaniline/carbon nanotubes coated with polyaniline(PCNTs) have been investigated using impedance analyzer and extensometer. The blends of PS/PANI formed the heterogeneous phase separated morphology in which PCNTs are dispersed uniformly. The incorporation of a small amount of PCNTs into the blend of PS/PANI has remarkably increased the dielectric properties. Similarly, the AC conductivity of PS/PANI is also increased five orders of magnitude from 1.6 × 10~(-10) to 2.0 × 10~(-5) S·cm~(-1) in the hybrid nanocomposites. Such behavior of hybrid nanocomposites is owing to the interfacial polarization occurring due to the presence of multicomponent domains with varying conductivity character of the phases from insulative PS to poor conductor PANI to highly conductive CNTs. Meanwhile, the tensile modulus and tensile strength are also enhanced significantly up to 55% and 160%, respectively, without much loss of ductility for three phase hybrid nanocomposites as compared to the neat PS. Thereby, the hybrid nanocomposites of PS/PANI/_P CNTs become stiffer, stronger and tougher as compared to the neat systems.     

Volume dependence of thermal conductivity and bulk modulus for poly(propylene glycol)

The thermal conductivity λ and heat capacity per unit volume of poly(propylene glycol) PPG (0.4 and 4.0 kg·mol⁻¹ in number-average molecular weight) have been measured in the temperature range 150–295 K at pressures up to 2 GPa using the transient hot-wire method. At 295 K and atmospheric pressure, λ = 0.147 W m⁻¹K⁻¹ for PPG (0.4 kg·mol⁻¹) and λ = 0.151 W m⁻¹K⁻¹ for PPG (4.0 kg·mol⁻¹). The temperature dependence of λ is less than 4 × 10⁻⁴ W m⁻¹K⁻² for both molecular weights. The bulk modulus has been measured in the temperature range 215–295 K up to 1.1 GPa. At atmospheric pressure, the room temperature bulk moduli are 1.97 GPa for PPG (0.4 kg·mol⁻¹) and 1.75 GPa for PPG (4.0 kg·mol⁻¹). These data were used to calculate the volume dependence of $ \lambda ,g\, = - \left( {\frac{{\partial \lambda /\lambda }}{{\partial V/V}}} \right)_T $. At room temperature and atmospheric pressure (liquid phase) we find g = 2.79 for PPG (0.4 kg·mol⁻¹) and g = 2.15 for PPG (4.0 kg·mol⁻¹). The volume dependence of g, (∂g/∂ log V)_T varies between −19 to −10 for both molecular weights. Under isochoric conditions, g is nearly independent of temperature. The difference in g between the glassy state and liquid phase is small and just outside the inaccuracy of g of about 8%. The theoretical model for λ by Horrocks and McLaughlin yields an overestimate of g by up to 120%. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 345–355, 1998     

Structural modulation induced by cobalt-based ionic liquids for enhanced thermoelectric transport in PEDOT:PSS

Poly(3,4ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) has been intensively studied for its thermoelectric applications. Structural modulation to improve crystalline ordering, chain conformation and film morphology is a promising way to decouple the trade-off between conductivity and Seebeck coefficient and thus improve the thermoelectric power factor. Post treatment with ionic liquid ([CoCl₂ ⋅ 6H₂O]:[ChCl]) bearing cobalt-containing anions resulted in a remarkable enhancement of the power factor to 76.8 μW m⁻¹ K⁻². This IL combines the influence of a high-boiling polar organic solvent and diffusing ions. A high σ mainly resulted from the efficient removal of PSS chains, ordering of the structure and delocalization of bipoloran-dominant transport after conformational change. The increase in S was not due to dedoping of PEDOT chains, but rather the sharp feature of the density of states at the Fermi level induced by ion-exchange with unconventional anions.     

Space-resolved thermal properties of thermoplastics reinforced with carbon nanotubes

Composites comprising biobased poly(lactic acid) (PLA) and polyethylene (Bio-PE) were reinforced with multi-walled carbon nanotubes (MWCNTs). These nanocomposites were analyzed using space-resolved thermal analysis (TA) integrated with atomic force microscopy. The deflection temperature, which indicates thermal-induced expansion and thermal transitions of the composite, was monitored by nanoscale TA (nanoTA) utilizing the displacement of a cantilever in contact with the material. Results were compared to bulk electrical, mechanical and thermal properties. Electrical conductivity was detected at lower MWCNT loadings for PLA than for Bio-PE (at 2.5 vs. 5 mass%). Maximal electrical conductivity of 27 S m^?1 for PLA and 0.7 S m^?1 for Bio-PE-based samples was reached at 10 mass% MWCNT loading. Tensile behavior combined with thermogravimetric analysis indicated strong MWCNT–Bio-PE interactions, in contrast to PLA. The glass transition and melting temperature measured by differential scanning calorimetry (DSC) were not changed by the increase in MWCNT loading. Increased deflection temperature was registered by bulk heat deflection measurements on Bio-PE, but not for PLA. The thermal transitions obtained by nanoTA at the nanoscale were in the same temperature range as the first transitions observed upon temperature ramp in DSC (e.g., glass transition and melt temperatures of PLA and Bio-PE, respectively). Remarkably, thermal expansion was detected by nanoTA for PLA- and Bio-PE-based composites below electrical percolation threshold as well as an increase in PLA softening temperature. Space-resolved nanothermal analysis revealed thermal phenomena that are otherwise overlooked when bulk methods are applied.     

Thermal conductivity enhancement of MWNTs on the PANI/tetradecanol form-stable PCM

We prepared PANI/tetradecanol/MWNTs composites via in-situ polymerization. DSC results indicated that the composites are good form-stable phase change materials (PCMs) with large phase change enthalpy of 115 J g⁻¹. The MWNTs were randomly dispersed in the composites and significantly enhanced the thermal conductivity of the PCMs from 0.33 to 0.43 W m⁻¹ K⁻¹. The form-stable PCMs won’t liquefy even it is heated at 80°C, so that the MWNTs were fixed in the composite and the phase separation of the MWNTs from PANI/tetradecanol/MWNTs composites won’t occur.     

Preparation and characterization of form-stable tetradecanol–palmitic acid expanded perlite composites containing carbon fiber for thermal energy storage

In this study, tetradecanol–palmitic acid/expanded perlite composites containing carbon fiber (TD-PA/EP-CF CPCMs) were prepared by a vacuum impregnation method. Binary eutectic mixtures of PA and TD were utilized as thermal energy storage material in the composites, where EP behaved as supporting material. X-ray diffraction demonstrated that crystal structures of PA, TD, EP, and CF remained unchanged, confirming no chemical interactions among raw materials besides physical combinations. The microstructures indicated that TD-PA was sufficiently absorbed into EP porous structure, forming no leakage even in molten state. Differential scanning calorimetry estimated the melting temperature of TD-PA/EP-CF CPCM to 33.6 °C, with high phase change latent heat (PCLH) of 138.3 kJ kg⁻¹. Also, the freezing temperature was estimated at 29.7 °C, with PCLH of 137.5 kJ kg⁻¹. The thermal cycling measurements showed that PCM composite had adequate stability even after 200 melting/freezing cycles. Moreover, the thermal conductivity enhanced from 0.48 to 1.081 W m⁻¹ K⁻¹ in the presence of CF. Overall, the proposed CPCMs look promising materials for future applications due to their appropriate phase change temperature, elevated PCLH, and better thermal stability.

     

Enhancement of thermal conductivity and tensile strength of liquid silicone rubber by three-dimensional alumina network

ABSTRACT

Rapidly increasing demands for higher integration density and stability of electronic devices embrace higher requirements for thermally conductive silicone rubber, which is promisingly used in ultra-thin components. In this work, alumina whiskers (AWs) and alumina flakes (AFs) are used to modify liquid silicone rubber (LSR) by fabricating binary (AFs/LSR) or ternary (AWs/AFs/LSR) composites. The thermal conductivity and mechanical strength of the binary and ternary composites were investigated. Thermal conductivity of the binary AFs/LSR composite (25AFs/LSR) was 0.1990 W m^?1 K^?1, while the thermal conductivity of the ternary AFs/AWs/LSR composite (20AFs/5AWs/LSR) was 0.2655 W m^?1 K^?1. Furthermore, the tensile strength of the ternary AWs/AFs/LSR composites increased by 180.9% as compared with the binary system, increased to 7.81 MPa from 2.78 MPa due to the introduction of 1 wt% AWs. As a reason, a significant synergistic effect of AWs and AFs in the enhancement of both thermal and mechanical properties of the LSR was proved. Furthermore, the dielectric property measurements demonstrated that the ternary composites exhibited a lower dielectric constant and dielectric loss, indicating that the AWs/AFs/LSR composites were qualified to be applied in the field of electronic devices.     

A High-Performance n-Type Thermoelectric Polymer from C−H/C−H Oxidative Direct Arylation Polycondensation

n-Type conjugated polymers (CPs) are crucial in the applications of organic electronics. Direct coupling of electron-deficient C−H monomer via selective C−H activation, namely C−H/C−H oxidative direct arylation polycondensation (Oxi-DArP), is an ideal approach toward such CPs. Herein, Oxi-DArP is firstly adopted to synthesize a high-performance n-type CP using a newly developed monomer, i.e., 3,6-di(thiazol-5-yl)-diketopyrrolopyrrole (Tz-5-DPP). Tz-5-DPP based homopolymer PTz - 5 - DPP with a molecular weight of 22 kDa has been synthesized via Oxi-DArP. After n-doping, PTz - 5 - DPP films exhibited electric conductivity values up to 8 S cm⁻¹ and power factors (PFs) up to 106 μW m⁻¹ K⁻². Notably, this PF value is the highest for n-type polymer thermoelectric materials to date. The Oxi-DArP synthesis and the excellent n-type performance of the polymer make this work an important step toward the straightforward and sustainable preparation of high-performance n-type polymer semiconductors.     

An effective approach to enhanced thermoelectric properties of PEDOT:PSS films by a DES post‐treatment

As conventional organic solvents present inherent toxicity, deep eutectic solvents (DES) have been considered as excellent candidates due to their green characteristics. In this work, thermoelectric properties enhancement of PEDOT:PSS films is achieved by introducing DES as an additive and post‐treatment reagent. Direct addition and post‐treatment approaches lead to a maximum Seebeck coefficient of 29.1 μV K^?1 and electrical conductivity of 620.6 S cm^?1, respectively. In addition, an optimal power factor is obtained by DES post‐treatment, reaching up to 24.08 μW m^?1 K^?2, which is approximately four orders of magnitude higher than the pure PEDOT:PSS. Assuming a thermal conductivity of 0.17 W m^?1 K^?1, the maximum ZT value is estimated to be 0.042 at 300 K. Further, atomic force microscopy and X‐ray photoelectron spectroscopy are performed and suggest that the remarkably enhanced electrical conductivity originates from the removal of the excess insulating PSS and the phase separation between the PEDOT and PSS chains. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 885–892