Thiol‐Assisted Synthesis of Carbon‐Supported Metal Nanoparticles for Efficient Electrocatalytic CO2 Reduction

The typical preparation route of carbon‐supported metallic catalyst is complex and uneconomical. Herein, we reported a thiol‐assisted one‐pot method by using 3‐mercaptopropionic acid (MPA) to synthesize carbon‐supported metal nanoparticles catalysts for efficient electrocatalytic reduction of carbon dioxide (CO₂RR). We found that the synthesized Au?MPA/C catalyst achieves a maximum CO faradaic efficiency (FE) of 96.2% with its partial current density of ?11.4 mA/cm², which is much higher than that over Au foil or MPA‐free carbon‐supported Au (Au/C). The performance improvement in CO₂RR over the catalyst is probably derived from the good dispersion of Au nanoparticles and the surface modification of the catalyst caused by the specific interaction between Au nanoparticles and MPA. This thiol‐assisted method can be also extended to synthesize Ag?MPA/C with enhanced CO₂RR performance.     

Molecular Evidence for Metallic Cobalt Boosting CO2 Electroreduction on Pyridinic Nitrogen

Nitrogen‐doped carbon materials (N‐C_mat) are emerging as low‐cost metal‐free electrocatalysts for the electrochemical CO₂ reduction reaction (CO₂RR), although the activities are still unsatisfactory and the genuine active site is still under debate. We demonstrate that the CO₂RR to CO preferentially takes place on pyridinic N rather than pyrrolic N using phthalocyanine (Pc) and porphyrin with well‐defined N‐C_mat configurations as molecular model catalysts. Systematic experiments and theoretic calculations further reveal that the CO₂RR performance on pyridinic N can be significantly boosted by electronic modulation from in‐situ‐generated metallic Co nanoparticles. By introducing Co nanoparticles, Co@Pc/C can achieve a Faradaic efficiency of 84 % and CO current density of 28 mA cm^?2 at ?0.9 V, which are 18 and 47 times higher than Pc/C without Co, respectively. These findings provide new insights into the CO₂RR on N‐C_mat, which may guide the exploration of cost‐effective electrocatalysts for efficient CO₂ reduction.     

Recent strategy(ies) for the electrocatalytic reduction of CO2: Ni single-atom catalysts for the selective electrochemical formation of CO in aqueous electrolytes

To decrease the global carbon footprint concerns and to diminish the energy crisis, electrocatalytic reduction of CO₂ which results in the formulation of value-added chemicals is a potential solution. In this review, single-atom catalysts (SACs) which are rapidly growing and being developed as the stimulating catalytic materials for electrocatalytic reduction of CO₂ with improved selectivity, efficiency, and stability are considered. Various factors which are responsible for the efficient CO₂ reduction are discussed. The pyrolytic approach for the preparation of Ni-based SACs and the maximum atom utilization efficiency for the desirable production of CO from CO₂ are highlighted.     

Boosting electrocatalytic selectivity in carbon dioxide reduction: The fundamental role of dispersing gold nanoparticles on silicon nanowires

Carbon dioxide electrochemical reduction (CO₂RR) has been recognized as an efficient way to mitigate CO₂ emissions and alleviate the pressure on global warming and associated environmental consequences. Gold (Au) is reported as stable and active electrocatalysts to convert CO₂ to CO at low overpotential due to its moderate adsorption strength of *COOH and *CO. The request for improved catalytic performance, however, is motivated by current unsatisfied catalytic selectivity because of the side hydrogen evolution reaction. In this context, the design of Au based binary catalysts that can boost CO selectivity is of great interest. In the present work, we report that Au nanoparticles can be feasibly dispersed and anchored on silicon nanowires to form Au-Si binary nanomaterials. The Au-Si may stably drive CO₂RR with a CO Faraday efficiency of 95.6% at ?0.6 V vs. RHE in 0.5 mol/L KHCO₃ solution. Such selectivity outperforms Au particles by up to 61%. Controlled experiments illustrate that such catalytic enhancement can chiefly be ascribed to electronic effects of binary catalysts. Theoretical calculations reveal that spontaneously produced silicon oxide may not only inhibit hydrogen evolution reaction, but also stabilize the key intermediate *COOH in CO formation.     

Electrochemical CO2 Activation and Valorization on Metallic Copper and Carbon-Embedded N-Coordinated Single Metal MNC Catalysts

The electrochemical reductive valorization of CO₂, referred to as the CO2RR, is an emerging approach for the conversion of CO₂-containing feeds into valuable carbonaceous fuels and chemicals, with potential contributions to carbon capture and use (CCU) for reducing greenhouse gas emissions. Copper surfaces and graphene-embedded, N-coordinated single metal atom (MNC) catalysts exhibit distinctive reactivity, attracting attention as efficient electrocatalysts for CO2RR. This review offers a comparative analysis of CO2RR on copper surfaces and MNC catalysts, highlighting their unique characteristics in terms of CO₂ activation, C₁/C₂₍₊₎ product formation, and the competing hydrogen evolution pathway. The assessment underscores the significance of understanding structure–activity relationships to optimize catalyst design for efficient and selective CO2RR. Examining detailed reaction mechanisms and structure-selectivity patterns, the analysis explores recent insights into changes in the chemical catalyst states, atomic motif rearrangements, and fractal agglomeration, providing essential kinetic information from advanced in/ex situ microscopy/spectroscopy techniques. At the end, this review addresses future challenges and solutions related to today's disconnect between our current molecular understanding of structure–activity-selectivity relations in CO2RR and the relevant factors controlling the performance of CO₂ electrolyzers over longer times, with larger electrode sizes, and at higher current densities.     

Bipyridine‐Assisted Assembly of Au Nanoparticles on Cu Nanowires To Enhance the Electrochemical Reduction of CO2

We report a new strategy to prepare a composite catalyst for highly efficient electrochemical CO₂ reduction reaction (CO₂RR). The composite catalyst is made by anchoring Au nanoparticles on Cu nanowires via 4,4′‐bipyridine (bipy). The Au‐bipy‐Cu composite catalyzes the CO₂RR in 0.1 m KHCO₃ with a total Faradaic efficiency (FE) reaching 90.6 % at ?0.9 V to provide C‐products, among which CH₃CHO (25 % FE) dominates the liquid product (HCOO^?, CH₃CHO, and CH₃COO^?) distribution (75 %). The enhanced CO₂RR catalysis demonstrated by Au‐bipy‐Cu originates from its synergistic Au (CO₂ to CO) and Cu (CO to C‐products) catalysis which is further promoted by bipy. The Au‐bipy‐Cu composite represents a new catalyst system for effective CO₂RR conversion to C‐products.     

Highly Efficient Porous Carbon Electrocatalyst with Controllable N-Species Content for Selective CO2 Reduction

We report a straightforward strategy to design efficient N doped porous carbon (NPC) electrocatalyst that has a high concentration of easily accessible active sites for the CO₂ reduction reaction (CO₂RR). The NPC with large amounts of active N (pyridinic and graphitic N) and highly porous structure is prepared by using an oxygen-rich metal–organic framework (Zn-MOF-74) precursor. The amount of active N species can be tuned by optimizing the calcination temperature and time. Owing to the large pore sizes, the active sites are well exposed to electrolyte for CO₂RR. The NPC exhibits superior CO₂RR activity with a small onset potential of −0.35 V and a high faradaic efficiency (FE) of 98.4 % towards CO at −0.55 V vs. RHE, one of the highest values among NPC-based CO₂RR electrocatalysts. This work advances an effective and facile way towards highly active and cost-effective alternatives to noble-metal CO₂RR electrocatalysts for practical applications.     

Design and Preparation of Electrocatalysts by Electrodeposition for CO2 Reduction

With the increasing emission of carbon dioxide (CO₂), the conversion and utilization of CO₂ have become a topic of increasing concern. Electrochemical CO₂ reduction reaction (CO₂RR) is an attractive and sustainable approach for solving energy and environmental problems. Design of efficient catalysts is crucial for achieving highly efficient CO₂RR. Different methods to prepare catalysts have been reported and used. Among them, electrodeposition is one of the common approaches, which has some obvious advantages, such as requiring simple equipment, environmentally benign. Especially, it can direct deposit catalysts on different substrates to prepare electrodes for CO₂RR. In this review, we discuss recent advances in design and preparation of the catalysts by electrodeposition and their applications in CO₂RR. Furthermore, the perspective of this promising area is also discussed.     

Highly Efficient Porous Carbon Electrocatalyst with Controllable N‐Species Content for Selective CO2 Reduction

We report a straightforward strategy to design efficient N doped porous carbon (NPC) electrocatalyst that has a high concentration of easily accessible active sites for the CO₂ reduction reaction (CO₂RR). The NPC with large amounts of active N (pyridinic and graphitic N) and highly porous structure is prepared by using an oxygen‐rich metal–organic framework (Zn‐MOF‐74) precursor. The amount of active N species can be tuned by optimizing the calcination temperature and time. Owing to the large pore sizes, the active sites are well exposed to electrolyte for CO₂RR. The NPC exhibits superior CO₂RR activity with a small onset potential of ?0.35 V and a high faradaic efficiency (FE) of 98.4 % towards CO at ?0.55 V vs. RHE, one of the highest values among NPC‐based CO₂RR electrocatalysts. This work advances an effective and facile way towards highly active and cost‐effective alternatives to noble‐metal CO₂RR electrocatalysts for practical applications.     

Size-Dependent Nickel-Based Electrocatalysts for Selective CO2 Reduction

Closing the anthropogenic carbon cycle by converting CO₂ into reusable chemicals is an attractive solution to mitigate rising concentrations of CO₂ in the atmosphere. Herein, we prepared Ni metal catalysts ranging in size from single atoms to over 100 nm and distributed them across N-doped carbon substrates which were obtained from converted zeolitic imidazolate frameworks (ZIF). The results show variance in CO₂ reduction performance with variance in Ni metal size. Ni single atoms demonstrate a superior Faradaic efficiency (FE) for CO selectivity (ca. 97 % at −0.8 V vs. RHE), while results for 4.1 nm Ni nanoparticles are slightly lower (ca. 93 %). Further increase the Ni particle size to 37.2 nm allows the H₂ evolution reaction (HER) to compete with the CO₂ reduction reaction (CO₂RR). The FE towards CO production decreases to under 30 % and HER efficiency increase to over 70 %. These results show a size-dependent CO₂ reduction for various sizes of Ni metal catalysts.     

Cu2O-Ag Tandem Catalysts for Selective Electrochemical Reduction of CO2 to C2 Products

The electrochemical carbon dioxide reduction reaction (CO₂RR) to C₂ chemicals has received great attention. Here, we report the cuprous oxide (Cu₂O) nanocubes cooperated with silver (Ag) nanoparticles via the replacement reaction for a synergetic CO₂RR. The Cu₂O-Ag tandem catalyst exhibits an impressive Faradaic efficiency (FE) of 72.85% for C₂ products with a partial current density of 243.32 mA·cm⁻². The electrochemical experiments and density functional theory (DFT) calculations reveal that the introduction of Ag improves the intermediate CO concentration on the catalyst surface and meanwhile reduces the C-C coupling reaction barrier energy, which is favorable for the synthesis of C₂ products.     

Polyoxometalate-based electron transfer modulation for efficient electrocatalytic carbon dioxide reduction

The electrocatalytic carbon dioxide (CO₂) reduction reaction (CO₂RR) involves a variety of electron transfer pathways, resulting in poor reaction selectivity, limiting its use to meet future energy requirements. Polyoxometalates (POMs) can both store and release multiple electrons in the electrochemical process, and this is expected to be an ideal “electron switch” to match with catalytically active species, realize electron transfer modulation and promote the activity and selectivity of the electrocatalytic CO₂RR. Herein, we report a series of new POM-based manganese-carbonyl (MnL) composite CO₂ reduction electrocatalysts, whereby SiW₁₂–MnL exhibits the most remarkable activity and selectivity for CO₂RR to CO, resulting in an increase in the faradaic efficiency (FE) from 65% (MnL) to a record-value of 95% in aqueous electrolyte. A series of control electrochemical experiments, photoluminescence spectroscopy (PL), transient photovoltage (TPV) experiments, and density functional theory (DFT) calculations revealed that POMs act as electronic regulators to control the electron transfer process from POM to MnL units during the electrochemical reaction, enhancing the selectivity of the CO₂RR to CO and depressing the competitive hydrogen evolution reaction (HER). This work demonstrates the significance of electron transfer modulation in the CO₂RR and suggests a new idea for the design of efficient electrocatalysts towards CO₂RR.

Polyoxometalates as electron regulators to promote the carbonyl manganese (MnL) electrocatalyst for highly efficient CO₂ reduction in aqueous electrolyte.     

Robust nickel silicate catalysts with high Ni loading for CO2 methanation

CO₂ is the main component of greenhouse gases and also an important carbon source. The hydrogenation of CO₂ to methane using Ni-based catalysts can not only alleviate CO₂ emissions but also obtain useful fuels. However, Ni-based catalysts face one major problem of the sintering of Ni nanoparticles in the process of CO₂ methanation. Thus, this work has synthesized a series of efficient and robust nickel silicate catalysts (NiPS−X) with different nickel content derived from nickel phyllosilicate by the hydrothermal method. It was found that the Ni loading plays a critical role in the structure and catalytic performance of the NiPS−X catalysts. The catalytic performance gradually increases with the increase of Ni loading. In particular, the highly dispersed NiPS-1.6 catalyst with a high Ni loading of 34.3 wt% could obtain the CO₂ conversion greater than 80%, and the methane selectivity was close to 100% for 48 h at 330 °C and the GHSV of 40,000 mL g⁻¹ h⁻¹. The excellent catalytic property can be assigned to the high dispersion of Ni nanoparticles and the strong interaction between the active component and the carrier, which is derived from a unique layered silicate structure with lots of nickel phyllosilicate and a large number of Lewis acid sites.     

In-Situ-Formed Potassium-Modified Nickel-Zinc Carbide Boosts Production of Higher Alcohols beyond CH4 in CO2 Hydrogenation

Ni-based catalysts have been widely studied in the hydrogenation of CO₂ to CH₄, but selective and efficient synthesis of higher alcohols (C₂₊OH) from CO₂ hydrogenation over Ni-based catalyst is still challenging due to successive hydrogenation of C1 intermediates leading to methanation. Herein, we report an unprecedented synthesis of C₂₊OH from CO₂ hydrogenation over K-modified Ni−Zn bimetal catalyst with promising activity and selectivity. Systematic experiments (including XRD, in situ spectroscopic characterization) and computational studies reveal the in situ generation of an active K-modified Ni−Zn carbide (K-Ni₃Zn₁C_0.7) by carburization of Zn-incorporated Ni⁰, which can significantly enhance CO₂ adsorption and the surface coverage of alkyl intermediates, and boost the C−C coupling to C₂₊OH rather than conventional CH₄. This work opens a new catalytic avenue toward CO₂ hydrogenation to C₂₊OH, and also provides an insightful example for the rational design of selective and efficient Ni-based catalysts for CO₂ hydrogenation to multiple carbon products.     

Electrochemical Conversion of CO2 to Syngas with Controllable CO/H2 Ratios over Co and Ni Single‐Atom Catalysts

The electrochemical CO₂ reduction reaction (CO₂RR) to yield synthesis gas (syngas, CO and H₂) has been considered as a promising method to realize the net reduction in CO₂ emission. However, it is challenging to balance the CO₂RR activity and the CO/H₂ ratio. To address this issue, nitrogen‐doped carbon supported single‐atom catalysts are designed as electrocatalysts to produce syngas from CO₂RR. While Co and Ni single‐atom catalysts are selective in producing H₂ and CO, respectively, electrocatalysts containing both Co and Ni show a high syngas evolution (total current >74 mA cm^?2) with CO/H₂ ratios (0.23–2.26) that are suitable for typical downstream thermochemical reactions. Density functional theory calculations provide insights into the key intermediates on Co and Ni single‐atom configurations for the H₂ and CO evolution. The results present a useful case on how non‐precious transition metal species can maintain high CO₂RR activity with tunable CO/H₂ ratios.     

室温快速合成Ag基金属有机骨架材料用于电催化还原CO2

选择具有强给电子能力的1,2,4-三唑为配体,成功合成了银基金属有机骨架材料(Ag-MOF)并用于电催化还原CO₂反应(CO₂RR)。借助粉末X射线衍射、透射电子显微镜、扫描电子显微镜、计时电流法等表征手段对材料的晶体结构、形貌和电催化CO₂RR性能进行了系统的研究。与商品化的纳米Ag颗粒对比,Ag-MOF展现出更优异的电催化CO₂RR产物选择性、催化活性和稳定性,在-0.9 V (vs RHE)时,CO的法拉第效率高达96.1%。当电压为-1.1 V (vs RHE)时,电流密度可达17 mA·cm^-2,且电极可以稳定运行300 min。这说明通过选择合适的配体结构,可以改变催化位点周围的化学环境,从而高效将CO₂转化为目标产物。     

室温快速合成Ag基金属有机骨架材料用于电催化还原CO2

选择具有强给电子能力的1,2,4-三唑为配体,成功合成了银基金属有机骨架材料(Ag-MOF)并用于电催化还原CO₂反应(CO₂RR)。借助粉末X射线衍射、透射电子显微镜、扫描电子显微镜、计时电流法等表征手段对材料的晶体结构、形貌和电催化CO₂RR性能进行了系统的研究。与商品化的纳米Ag颗粒对比,Ag-MOF展现出更优异的电催化CO₂RR产物选择性、催化活性和稳定性,在-0.9 V (vs RHE)时,CO的法拉第效率高达96.1%。当电压为-1.1 V (vs RHE)时,电流密度可达17 mA·cm^-2,且电极可以稳定运行300 min。这说明通过选择合适的配体结构,可以改变催化位点周围的化学环境,从而高效将CO₂转化为目标产物。     

室温快速合成Ag基金属有机骨架材料用于电催化还原CO2

选择具有强给电子能力的1,2,4-三唑为配体,成功合成了银基金属有机骨架材料(Ag-MOF)并用于电催化还原CO₂反应(CO₂RR)。借助粉末X射线衍射、透射电子显微镜、扫描电子显微镜、计时电流法等表征手段对材料的晶体结构、形貌和电催化CO₂RR性能进行了系统的研究。与商品化的纳米Ag颗粒对比,Ag-MOF展现出更优异的电催化CO₂RR产物选择性、催化活性和稳定性,在-0.9 V (vs RHE)时,CO的法拉第效率高达96.1%。当电压为-1.1 V (vs RHE)时,电流密度可达17 mA·cm^-2,且电极可以稳定运行300 min。这说明通过选择合适的配体结构,可以改变催化位点周围的化学环境,从而高效将CO₂转化为目标产物。     

Electrochemical Conversion of CO2 to Syngas with Controllable CO/H2 Ratios over Co and Ni Single-Atom Catalysts

The electrochemical CO₂ reduction reaction (CO₂RR) to yield synthesis gas (syngas, CO and H₂) has been considered as a promising method to realize the net reduction in CO₂ emission. However, it is challenging to balance the CO₂RR activity and the CO/H₂ ratio. To address this issue, nitrogen-doped carbon supported single-atom catalysts are designed as electrocatalysts to produce syngas from CO₂RR. While Co and Ni single-atom catalysts are selective in producing H₂ and CO, respectively, electrocatalysts containing both Co and Ni show a high syngas evolution (total current >74 mA cm⁻²) with CO/H₂ ratios (0.23–2.26) that are suitable for typical downstream thermochemical reactions. Density functional theory calculations provide insights into the key intermediates on Co and Ni single-atom configurations for the H₂ and CO evolution. The results present a useful case on how non-precious transition metal species can maintain high CO₂RR activity with tunable CO/H₂ ratios.     

Transition Metal Nitrides as Promising Catalyst Supports for Tuning CO/H2 Syngas Production from Electrochemical CO2 Reduction

The electrochemical carbon dioxide reduction reaction (CO₂RR) to produce synthesis gas (syngas) with tunable CO/H₂ ratios has been studied by supporting Pd catalysts on transition metal nitride (TMN) substrates. Combining experimental measurements and density functional theory (DFT) calculations, Pd‐modified niobium nitride (Pd/NbN) is found to generate much higher CO and H₂ partial current densities and greater CO Faradaic efficiency than Pd‐modified vanadium nitride (Pd/VN) and commercial Pd/C catalysts. In‐situ X‐ray diffraction identifies the formation of PdH in Pd/NbN and Pd/C under CO₂RR conditions, whereas the Pd in Pd/VN is not fully transformed into the active PdH phase. DFT calculations show that the stabilized *HOCO and weakened *CO intermediates on PdH/NbN are critical to achieving higher CO₂RR activity. This work suggests that NbN is a promising substrate to modify Pd, resulting in an enhanced electrochemical conversion of CO₂ to syngas with a potential reduction in precious metal loading.