Enhanced specific energy of silver-doped MnO2/graphene oxide electrodes as facile fabrication symmetric supercapacitor device

The present work is about the preparation of silver (Ag)-doped manganese oxide (MnO₂)/graphene oxide (GO) composite thin films are deposited by a facile and binder-free successive ionic layer adsorption and reaction (SILAR) method for the first time. The Brunauer-Emmett-Teller (BET) study revealed the nanosheets of MnO₂–Ag3/GO exhibit high specific surface area of 192 m² g^?1. The tailored flower-like morphology and interconnected nanosheets of MnO₂–Ag3/GO electrodes achieved high electrochemical performance. The maximum specific capacitance (Cs) of 877 F g^?1 at the scan rate of 5 mV s^?1 is obtained for MnO₂–Ag3/GO electrode tested in 1 M sodium sulfate (Na₂SO₄) electrolyte with capacity retention of 94.57% after 5000 cycling stability. The MnO₂–Ag3/GO composite-based flexible solid state symmetric supercapacitor (FSS-SSC) device delivered Cs as 164 F g^?1 with specific energy of 57 Wh kg^?1 at specific power of 1.6 kW kg^?1 and capacitive retention of 94% after 10,000 cycles.     

Optimization of cadmium adsorption from aqueous solutions by functionalized graphene and the reversible magnetic recovery of the adsorbent using response surface methodology

Novel functionalized graphene adsorbent was prepared and characterized using different techniques. The prepared adsorbent was applied for the removal of cadmium ions from aqueous solution. A response surface methodology was used to evaluate the simple and combined effects of the various parameters, including adsorbent dosage, pH, and initial concentration. Under the optimal conditions, the cadmium removal performance of 70% was achieved. A good agreement between experimental and predicted data in this study was observed. The experimental results revealed of cadmium adsorption with high linearity follow Langmuir isotherm model with maximum adsorption capacity of 502 mg g^?1, and the adsorption data fitted well into pseudo‐second order model. Thermodynamic studies showed that adsorption process has exothermic and spontaneous nature. The recommended optimum conditions are: cadmium concentration of 970 mg L^?1, adsorbent dosage of 1 g L^?1, pH of 6.18, and T = 25 °C. The magnetic recovery of the adsorbent was performed using a magnetic surfactant to form a noncovalent magnetic functionalized graphene. After magnetic recovery of the adsorbent both components (adsorbent and magnetic surfactant) were recycled by tuning the surface charges through changing the pH of the solution. Desorption behavior studied using HNO₃ solution indicated that the adsorbent had the potential for reusability.     

The effect of calcination temperature on the texture of silica gel waste

In this work, the effect of temperature on the texture of silica gel waste is presented and water vapour adsorption in a different humidity is highlighted. It was found that silica gel waste is a mesoporous material with the parallel plates pores. Its specific surface area is equal to 4.61 m² g^?1, and the calculated total pore volume is equal to 9.01 × 10^?3 cm³ g^?1. The texture of silica gel waste changed during calcination in a 188–550 °C temperature interval: S_BET and ΣV_P increased to 11.32 m² g^?1 and 30.06 × 10^?3 cm³ g^?1, respectively. It was determined that the water vapour pressure influenced the mineralogical composition and the quantity of adsorbed water in the samples. The obtained results were confirmed by the differential scanning microcalorimetry, X-ray diffraction, BET and water vapour adsorption analysis data.

     

Introduction of CdO nanoparticles into graphene and graphene oxide nanosheets for increasing adsorption capacity of Cr from wastewater collected from petroleum refinery

Graphene and graphene oxide nanocomposites are promising and fascinating types of nanocomposites because of their fast kinetics, unique affinity for heavy metals, and greater specific area. Initially, in this study, a green, cost-effective and facile method was utilized to prepare G, GO, CdO, G-CdO, and CdO-GO nanocomposites by Azadirachta indica and then analyzed using UV–vis spectroscopy, Fourier-transform spectroscopy, Raman, X-ray diffraction and scanning electron microscope. The synthesized nanocomposites were explored for chromium elimination from wastewater collected from a petroleum refinery. CdO-GO, G-CdO nanocomposites showed remarkable adsorption capability of 699 and 430 mg g^?1 which was higher than G (80 mg g^?1), GO (65 mg g^?1), and CdO (400 mg g^?1). Based on the R² (correlation coefficient) values, the kinetic statistics of Cr (VI) onto the G, GO, CdO, G-CdO, and CdO-GO were effectively obeyed by pseudo-second-order than by all other models. The R² values for the five nano-bioadsorbents were extraordinarily high (R² greater than 0.990) which ensured the chemisorption. This study ensured that the adsorptive removal rate of Cr (VI) is still greater than 85 % after repeated five cycles, suggesting that the produced nanomaterials are adsorbents with strong recyclability.     

Effective removal of 2,4,6‐trinitrophenol over hexagonal metal–organic framework NH2‐MIL‐88B(Fe)

A nanostructured organic–inorganic framework, hexagonal NH₂‐MIL‐88B, has been prepared through a facile one‐pot reflux reaction and then it was characterized using various techniques. The as‐prepared sample with high specific surface area (414 m² g^?1) showed excellent adsorption for 2,4,6‐trinitrophenol (TNP) in the liquid phase. Detailed studies of the adsorption kinetics, adsorption mechanism, adsorption isotherm, activation energy and various thermodynamic parameters were conducted. The adsorption mechanism of NH₂‐MIL‐88B for TNP may be ascribed to hydrogen bond interaction, and the complexation between ─OH in TNP and unsaturated Fe(III) on the surface of NH₂‐MIL‐88B. The maximum adsorption capacity of NH₂‐MIL‐88B for TNP based on the Langmuir isotherm was 163.66 mg g^?1. The as‐prepared NH₂‐MIL‐88B adsorbent seems to be a promising material in practice for TNP removal from aqueous solution.     

Adsorption calorimetry

The efficiency of activated carbons prepared from corncob, to remove asphaltenes from toluene modeled solutions, has been studied in this work. The activating agent effect over carbonaceous solid preparation , and also temperature effect on the asphaltenes adsorption on the prepared activated carbons, was studied. The asphaltene adsorption isotherms were determined, and the experimental data were analyzed applying the Langmuir, Freundlich, Redlich–Peterson, Toth and Radke–Prausnitz and Sips models. Redlich–Peterson model described the asphaltenes isotherm on the activated carbons better. The asphaltenes adsorption capacities at 25° for activated carbons were: 1305 mg g^?1, 1654 mg g^?1 and 559.1 mg g^?1 for GACKOH, GACKP and GACH₃PO₄, respectively. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° were also evaluated from the adsorption isotherms in asphaltene solutions from toluene solutions, and it was found that the adsorption process was spontaneous and exothermic in nature. Kinetic parameters, reaction rate constant and equilibrium adsorption capacities were evaluated and correlated for each kinetic model. The results show that asphaltene adsorption is described by pseudo-second-order kinetics, suggesting that the adsorption process is chemisorption. The adsorption calorimetry was used to analyze the type of interaction between the asphaltenes and the activated carbons prepared in this work, and their values were compared with the enthalpic values obtained from the Clausius–Clapeyron equation.

     

Facile synthesis of mesoporous magnesium oxide–graphene oxide composite for efficient and highly selective adsorption of hazardous anionic dyes

Mesoporous magnesium oxide–graphene oxide composite (MGC) has been synthesized using a facile post-immobilization method by mixing pre-synthesized magnesium oxide (MgO) with graphene oxide (GO). MgO used for fabrication of the composite has been synthesized using an environment-friendly method involving gelatin as a template. XRD, Raman and EDX analyses have confirmed the presence of MgO and GO in the composite. FTIR and SEM analyses of synthesized MGC have further elucidated the surface functionalities and morphology, respectively. Using N₂ adsorption–desorption isotherm, BET surface area of MGC has been calculated to be 55.9 m² g^?1 and BJH analysis confirmed the mesoporous nature of MGC. The application of synthesized MGC as a selective adsorbent for various toxic anionic dyes has been explored. Batch adsorption studies have been carried out to investigate the influence of different adsorption parameters on the adsorption of two anionic dyes: indigo carmine (IC) and orange G (OG). The maximum adsorption capacities exhibited by MGC for IC and OG are 252.4 and 24.5 mg g^?1, respectively. Plausible mechanism of dye adsorption has been explained in detail using FTIR analysis. In a mixture of cationic and anionic dyes, MGC selectively adsorbs anionic dyes with high separation factors, while in binary mixtures of anionic dyes, both dyes are adsorbed efficiently. Thus, MGC has been shown to be a potential adsorbent for the selective removal of anionic dyes from wastewater.

     

Remediation of Cd2+ in aqueous systems by alkali-modified (Ca) biochar and quantitative analysis of its mechanism

Co-pyrolysis of straw and Ca(OH)₂ is a feasible modification method to improve the adsorption capacity of biochar for Cd. However, few studies have quantitatively analyzed the contribution of different adsorption mechanisms of alkali-modified biochar. In this study, the alkali-modified (Ca) biochar were prepared by co-pyrolyzing lime (Ca(OH)₂) and soybean straw (SBB) or rape straw (RSB) at 450 °C. The adsorption mechanism was investigated by a series of experiments and was provided by quantitative analysis. The maximum adsorption capacities of Cd²⁺ by Ca-SBB and Ca-RSB were calculated to be 78.49 mg g^?1 and 49.96 mg g^?1, which were 1.56 and 1.48 times higher than SBB (50.40 mg g^?1) and RSB (33.79 mg g^?1), respectively. Compared with the original biochar (SBB, RSB), alkali-modified biochar (Ca-SBB and Ca-RSB) were found to have faster adsorption kinetics and lower desorption efficiencies. The mechanism study indicated that Ca(OH)₂ modification effectively enhanced the contribution of ion exchange and decreased the contribution of functional groups complexation. After Ca(OH)₂ modification, precipitation and ion exchange mechanisms dominated Cd^2 + absorption on Ca-SBB, accounting for 49.85% and 34.94% of the total adsorption, respectively. Similarily ion exchange and precipitation were the main adsorption mechanism on Ca-RSB, accounting however for 61.91% and 18.47% of total adsorption, respectively. These results suggested that alkali-modified biochar has great potential to adsorp cadmium in wastewater.     

Synthesis and acid catalysis of cellulose-derived carbon-based solid acid

SO₃H-bearing amorphous carbon, prepared by partial carbonization of cellulose followed by sulfonation in fuming H₂SO₄, was applied as a solid catalyst for the acid-catalyzed hydrolysis of β-1,4 glucan, including cellobiose and crystalline cellulose. Structural analyses revealed that the resulting carbon material consists of graphene sheets with 1.5 mmol g^?1 of SO₃H groups, 0.4 mmol g^?1 of COOH, and 5.6 mmol g^?1 of phenolic OH groups. The carbon catalyst showed high catalytic activity for the hydrolysis of β-1,4 glycosidic bonds in both cellobiose and crystalline cellulose. Pure crystalline cellulose was not hydrolyzed by conventional strong solid Brønsted acid catalysts such as niobic acid, Nafion^® NR-50, and Amberlyst-15, whereas the carbon catalyst efficiently hydrolyzes cellulose into water-soluble saccharides. The catalytic performance of the carbon catalyst is due to the large adsorption capacity for hydrophilic reactants and the adsorption ability of β-1,4 glucan, which is not adsorbed to other solid acids.     

Optimizing adsorptive removal of malachite green and methyl orange dyes from simulated wastewater by Mn‐doped CuO‐Nanoparticles loaded on activated carbon using CCD‐RSM: Mechanism,regeneration, isotherm,kinetic, and thermodynamic studies

In the present work, Mn‐doped CuO‐NPs‐AC was prepared by a simple method, characterized using various techniques such as FESEM, EDX, XRD, PSD, and pH_pzc and finally used for the adsorption of malachite green (MG) and methyl orange (MO) in a number of single and binary solutions. A series of adsorption experiments were conducted to investigate and optimize the influence of various factors (such as different pH, concentration of MG and MO, adsorbent mass, and sonication time) on the simultaneous adsorption of MG and MO using response surface methodology. Under optimal conditions of pH 10, adsorbent dose of 0.02 g, MG concentration of 30 mg L^?1, MO concentration of 30 mg L^?1, and sonication time of 4.5 min at room temperature, the maximum predicted adsorption was observed to be 100.0%, for both MG and MO, showing that there is a favorable harmony between the experimental data and model predictions. The adsorption isotherm of MO and MG by Mn‐doped CuO‐NPs‐AC could be well clarified by the Langmuir model with maximum adsorption capacity of 320.69 mg g^?1 and 290.11 mg g^?1 in the single solution and 233.02 mg g^?1 and 205.53 mg g^?1 in the binary solution by 0.005 g of adsorbent mass for MG and MO, respectively. Kinetic studies also revealed that both MG and MO adsorption were better defined by the pseudo‐second order model for both solutions. In addition, the thermodynamic constant studies disclosed that the adsorption of MG and MO was likely to be influenced by a physisorption mechanism. Eventually, the reusability of the Mn‐doped CuO‐NPs‐AC after six times showed a reduction in the adsorption percentage of MG and MO.     

Waste cigarette filters: activated carbon as a novel sorbent for uranium removal

Uranium is important in the nuclear fuel cycle as both as an energy source and as radioactive waste. Herein, activated carbon (AC) prepared from waste cigarette filters by convenient carbonization and functionalization was chosen as the raw materials for radionuclides adsorption. Batch adsorption experiments showed that AC presented comparable UO₂²⁺ adsorption capacity (106 mg g^?1) and very outstanding selectivity. The adsorption process accorded with Langmuir model and the pseudo-second-order kinetics model well. This work combines the waste cigarette filters with the radioactive nuclear treatment materials, which may provide a new strategy for the future treatment of waste cigarette butts.

     

Three‐Dimensional MoS2 Hierarchical Nanoarchitectures Anchored into a Carbon Layer as Graphene Analogues with Improved Lithium Ion Storage Performance

Much attention has recently been focused on the synthesis and application of graphene analogues of layered nanomaterials owing to their better electrochemical performance than the bulk counterparts. We synthesized graphene analogue of 3D MoS₂ hierarchical nanoarchitectures through a facile hydrothermal route. The graphene‐like MoS₂ nanosheets are uniformly dispersed in an amorphous carbon matrix produced in situ by hydrothermal carbonization. The interlaminar distance between the MoS₂ nanosheets is about 1.38 nm, which is far larger than that of bulk MoS₂ (0.62 nm). Such a layered architecture is especially beneficial for the intercalation and deintercalation of Li⁺. When tested as a lithium‐storage anode material, the graphene‐like MoS₂ hierarchical nanoarchitectures exhibit high specific capacity, superior rate capability, and enhanced cycling performance. This material shows a high reversible capacity of 813.5 mAh g^?1 at a current density of 1000 mA g^?1 after 100 cycles and a specific capacity as high as 600 mAh g^?1 could be retained even at a current density of 4000 mA g^?1. The results further demonstrate that constructing 3D graphene‐like hierarchical nanoarchitectures can effectively improve the electrochemical performance of electrode materials.     

Facile synthesis of polyaniline/TiO2/graphene oxide composite for high performance supercapacitors

The polyaniline/TiO₂/graphene oxide (PANI/TiO₂/GO) composite, as a novel supercapacitor material, is synthesized by in situ hydrolyzation of tetrabutyl titanate and polymerization of aniline monomer in the presence of graphene oxide. The morphology, composition and structure of the composites as-obtained are characterized by SEM, TEM, XRD and TGA. The electrochemical property and impedance of the composites are studied by cyclic voltammetry and Nyquist plot, respectively. The results show that the introduction of the GO and TiO₂ enhanced the electrode conductivity and stability, and then improved the supercapacitive behavior of PANI/TiO₂/GO composite. Significantly, the electrochemical measurement results show that the PANI/TiO₂/GO composite has a high specific capacitance (1020 F g⁻¹ at 2 mV s⁻¹, 430 F g⁻¹ at 1 A g⁻¹) and long cycle life (over 1000 times).     

Nanostructured Fe2O3–graphene composite as a novel electrode material for supercapacitors

Nanostructured Fe₂O₃–graphene composite was successfully fabricated through a facile solution-based route under mild hydrothermal conditions. Well-crystalline Fe₂O₃ nanoparticles with 30–60?nm in size are highly encapsulated in graphene nanosheet matrix, as demonstrated by various characterization techniques. As electrode materials for supercapacitors, the as-obtained Fe₂O₃–graphene nanocomposite exhibits large specific capacitance (151.8?F?g^?1 at 1?A?g^?1), good rate capability (120?F?g^?1 at 6?A?g^?1), and excellent cyclability. The significantly enhanced electrochemical performance compared with pure graphene and Fe₂O₃ nanoparticles may be attributed to the positive synergetic effect between Fe₂O₃ and graphene. In virtue of their superior electrochemical performance, they will be promising electrode materials for high-performance supercapacitors applications.     

A high performance solid-state asymmetric supercapacitor based on Anderson-type polyoxometalate-doped graphene aerogel

The manufacture of single-atom transition metal-doping carbon nanocomposites as electrode materials is crucial for electrochemical energy storage with high energy and power density. However, the simple strategy for preparation of such active materials with controlled structure remains a great challenge. Here, cobalt-doped carbon nanocomposites (Co-POM/rGO) were synthesized successfully by deposition of Anderson-type polyoxometalate (POM) on the surface of reduced graphene oxide (rGO) aerogel via one-pot hydrothermal treatment. The resulting Co-POM/rGO possesses three-dimensional graphene-based frameworks with hierarchical porous structure, high surface area and uniform single-atom metal doping. These intriguing features render Co-POM/rGO to be a promising electrode for applications in electrochemical energy storage. As an electrode material of a supercapacitor, Co-POM/rGO shows high-performance electrochemical energy storage (211.3 F g^?1 at 0.5 A g^?1). Furthermore, the solid-state asymmetric supercapacitor (ASC) device, using Co-POM/rGO as a positive electrode, exhibits the outstanding energy density of 37.6 Wh kg^?1 at a power density of 500 W kg^?1, and high capacitance retention of 95.2% after 5000 charge–discharge cycles. These results indicate that the proposed strategy for rational design of single-atom-metal doped carbon nanocomposites for flexible ASC devices with excellent capacitive properties.

     

Hierarchically porous tobacco midrib-based biochar prepared by a simple dual-templating approach for highly efficient Rhodamine B removal

High volatile matter contents in the feedstock could promote the development of porous structures and the reactivity of biochar. Herein, tobacco midrib with high volatile matter contents was used to prepare biochar by a dual-templating approach with mild activators (K₂C₂O₄·H₂O, CaCO₃). The characterizations of textural properties indicated that tobacco midrib-based biochar possessed numerous meso-, micro-, and macro-pores, specific surface area reached 1841.9 m² g^?1. As a dye adsorbent, the adsorption capacity of this biochar towards Rhodamine B reached 588.7 mg g^?1. After recycling 5 times, it still retained over 90% of its initial adsorption capacity. Moreover, thermodynamic parameters assessed with full vańt Hoff equation confirmed that dye molecules replace water molecules connected on biochar surface during the adsorption according to negative heat capacity change (-3.9 kJ mol^?1 K^?1), ΔH⁰ (–22.1 kJ mol^?1) and ΔS⁰ (0.3 kJ mol^?1) revealed that the adsorption process of Rh B by TMB was exothermic and the disorder of the solid–liquid interface increased. Overall, this research provides a mild and effective approach to modifying biochar from special tissue of agriculture waste and an insight into the process of dye adsorption on biochar from thermodynamics.     

功能化石墨烯/活性炭复合电极及不对称电容器脱盐

以3-氨丙基三乙氧基硅烷(AMPTS)修饰氧化石墨(GO)还原合成氨基功能化石墨烯(GP-NH₂). 傅里叶变换红外(FTIR)光谱和X射线能谱(EDX)分析证明了氨基基团的成功接枝. 以GP-NH₂为添加剂, 制备胺化石墨烯/活性炭(GP-NH₂/AC)复合电极, 并以GP-NH₂/AC 为正极, AC电极为对电极, 组装不对称电容器(AC||GPNH₂/AC)用于电容脱盐. 实验表明, AC||GP-NH₂/AC 单循环脱盐量为7.63 mg·g^-1, 电流效率达77.6%. 利用磺酸重氮盐接枝石墨烯制备磺化石墨烯(GP-SO₃H)及磺化石墨烯/活性炭(GP-SO₃H/AC)复合电极. 并以GPSO₃H/AC为负极, GP-NH₂/AC 为正极, 组装不对称电容器(GP-SO₃H /AC||GP-NH₂/AC)用于电容脱盐, 其平均脱盐速率可达0.99 mg·g^-1·min^-1, 比纯AC电极提高了接近5倍. 充放电速率提高了30%; 而且由于正、负极表面固有电荷的存在, 大大降低了反离子效应, 电流效率由40% (纯AC||AC对称电容器)提高到92.8%. 表明电极内功能化导电石墨烯的存在既提高了导电性, 又兼具离子选择性的作用, 从而明显改善电极的脱盐性能.     

The effect of activation technology on the electrochemical performance of calcium carbide skeleton carbon

Porous CaC₂-derived carbon (CCDC) was synthesized by one-step route from CaC₂ in a freshly prepared chlorine environment at lower temperature. As-prepared CCDC was activated by H₃PO₄, ZnCl₂, and KOH, respectively. The effects of the activation technology on the structure and morphology of CCDC were studied by X-ray diffraction, physical N₂ adsorption/desorption, and transmission electron microscopy. It has been found that the pore structure and specific surface area of CCDC are apparently improved after activation; the CCDC activated by KOH especially showed an excellent specific surface area of 1,100?m²?g^?1. The electrochemical performance of supercapacitors using activated CCDC as electrode active material was studied by cyclic voltammery, galvanostatic charge/discharge, and cycle life measurements. The results indicated that the CCDCs activated by H₃PO₄, ZnCl₂, and KOH revealed enhanced capacitances of 172.6, 198.1, and 250.1?F?g^?1 in 6?M KOH electrolyte, which were increased by 11.4, 27.8, and 61.2?% compared with the pristine CCDC (155?F?g^?1), respectively. Furthermore, the supercapacitors using all activated CCDCs as electrode active material exhibited excellent cycle stability, and the specific capacitance for all activated CCDC samples had nearly no change after 5,000 cycles.     

Preparation and adsorption performance of a NiO/MgF2 composite adsorbent

Fluoride adsorbents have been applied for the purification of UF₆ product from fluorination process. A MgF₂-based adsorbent, NiO/MgF₂, was prepared using NiF₂ as doping agent. The specific surface area of NiO/MgF₂ was 5 times larger than that of MgF₂, its porosity was also larger than that of MgF₂. The saturated adsorption capacity of NiO/MgF₂ for MoF₆ was 21.4?±?1.9 mg g^?1. The desorption behavior was examined by thermogravimetric analysis (TG). The NiO/MgF₂ with adsorbed MoF₆ was investigated using extended X-ray absorption fine structure spectroscopy (EXAFS), which showed no bonding interactions between NiO and MoF₆, while the adsorption of MoF₆ on NiO/MgF₂ was chemisorption via a Mo–F–Mg bond.

     

Sulfonated poly(ether ether ketone)/manganese dioxide composite for the removal of low level radionuclide ions from aqueous solution

Various composite adsorbents based on sulfonated poly(ether ether ketone)/manganese dioxide were prepared for the removal of stable and radioactive ions from contaminated aqueous solution. Batch adsorption experiments revealed superior adsorption capacities of the composite using very low initial concentration of studied elements. Starting with 1000 µg L⁻¹ contaminated solution, the maximum equilibrium metal uptake capacity reached 2.0 mg g⁻¹ for Pb²⁺, 1.9 mg g⁻¹ for Cd²⁺, Cu²⁺ and Zn²⁺, and 3.7 mg g⁻¹ for Co²⁺. In addition, the distribution coefficient reached 11,600 mL g⁻¹ for ¹³⁷Cs and 70,000 mL g⁻¹ for ²¹⁰Pb.