Application of Nano-Hydroxyapatite Derived from Oyster Shell in Fabricating Superhydrophobic Sponge for Efficient Oil/Water Separation

The exploration of nonhazardous nanoparticles to fabricate a template-driven superhydrophobic surface is of great ecological importance for oil/water separation in practice. In this work, nano-hydroxyapatite (nano-HAp) with good biocompatibility was easily developed from discarded oyster shells and well incorporated with polydimethylsiloxane (PDMS) to create a superhydrophobic surface on a polyurethane (PU) sponge using a facile solution–immersion method. The obtained nano-HAp coated PU (nano-HAp/PU) sponge exhibited both excellent oil/water selectivity with water contact angles of over 150° and higher absorption capacity for various organic solvents and oils than the original PU sponge, which can be assigned to the nano-HAp coating surface with rough microstructures. Moreover, the superhydrophobic nano-HAp/PU sponge was found to be mechanically stable with no obvious decrease of oil recovery capacity from water in 10 cycles. This work presented that the oyster shell could be a promising alternative to superhydrophobic coatings, which was not only beneficial to oil-containing wastewater treatment, but also favorable for sustainable aquaculture.     

树莓状超疏水多孔复合棉纤维的制备及油水分离性能

基于聚多巴胺（PDA）的化学性质和树莓状纳米粒子的粗糙结构,以聚多巴胺包覆的棉纤维为基底,制备了具有多重粗糙度的树莓状超疏水多孔复合棉纤维材料.通过扫描电子显微镜观察树莓状超疏水多孔复合棉纤维表面的微观形貌,PDA-SiO₂纳米粒子稳定地固定在聚多巴胺涂覆的棉纤维表面.经过氟化改性的树莓状超疏水多孔复合棉纤维具有超疏水性,水接触角为158.2°,油接触角为0°.油/水分离实验结果表明,树莓状超疏水多孔复合棉纤维对己烷/水混合物的分离效率可达99.4%以上,使用20次后仍维持较高的分离效率.同时,其具有较高的溶剂吸附能力（13~34 g/g）、重复使用性及机械稳定性,吸油能力可与硅气凝胶相媲美.     

Influence of caged bicyclic phosphate and CaCO3 nanoparticles on char-forming property of PU rigid foams

Char-forming property of PU rigid foams, which can be assessed by char residue (%) when PU is burned at certain temperature, was studied by TG and DTG. The results showed that pure PU rigid foam had low char residue of only 17%, while 33% of char residue was achieved when PU rigid foam was modified by adding 8 wt% of 1-oxo-2,6,7-trioxa-1-phosphabicyclo[2,2,2] octane (PEPA), which is a caged bicyclic phosphate. The experiment results of FTIR and XPS showed that the PEPA modified PU rigid foam could be dehydrogenated and dehydrated at temperature between 380 and 450 °C, resulting in the increase of char residue of PU rigid foam. Further study also revealed that the addition of CaCO₃ nanoparticles could enhance the char stability when the PEPA modified PU rigid foam was being burned. The mechanism was investigated and it was found that the enhanced char stability could be attributed to the limited permeation of oxygen caused by the formation of calcium phosphate and calcium pyrophosphate by the reaction of PEPA and CaCO₃ at high temperature, which were covered on or buried in the char layer.     

Preparation of Silver Nanoparticles Incorporated Electrospun Polyurethane Nano-fibrous Mat for Wound Dressing

Polyurethane foam is currently used as an exudate absorptive wound dressing material. In this study silver (Ag) nanoparticles were incorporated into electrospun polyurethane (PU) nanofiber to enhance the antibacterial as well as wound healing properties. The electrospinning parameters were optimized for PU with and without silver nanoparticles. Silver nanoparticles were synthesized by aqueous and organic methods. The water absorption, antibacterial and cytocompatibility of the PU-Ag nanofibers were studied and compared to that of conventional PU foam. The results indicated that the PU-Ag nanofibers could be used for wound dressing applications.     

A Scalable Chemical Approach for the Synthesis of a Highly Tolerant and Efficient Oil Absorbent

In the past, bio‐inspired extreme water repellent property has been strategically embedded on commercially available sponges for developing selective oil absorbents. However, most of the reported materials lack physical and chemical durability, limiting their applicability at practically harsh settings. Herein, a stable dispersion of polymeric nanocomplexes was exploited to achieve a chemically reactive coating on the highly compressible melamine foam. A superhydrophobic melamine foam (SMF) was achieved after post‐covalent modification of the reactive coating through 1,4‐conjugate addition reaction at ambient conditions. The durability of the embedded extreme water repellent property in the as‐modified melamine foam has been elaborately demonstrated through exposing it to severe physical manipulations, chemically harsh aqueous media including pH 1, pH 12, surfactant contaminated water, river water, seawater and prolonged UV irradiation. Thus, the highly tolerant SMF was utilized as an efficient oil absorbent wherein oils of varying densities could be selectively recovered from an oil/water interface with high (e.g., 137 g g^?1 for chloroform and 83 g g^?1 for diesel) oil absorption capacity. Moreover, the selective oil absorption capacity of the as‐synthesized material remained unaffected at practically relevant severe chemical and physical settings, and the extreme water repellency of the material remained unaltered even after repetitive (at least 50 cycles) use for oil/water separation.     

Rigid polyurethane foams reinforced with disilanolisobutyl POSS: Synthesis and properties

This work reports the synthesis of rigid polyurethane (PU) foams modified by disilanolisobutyl polyhedral oligomeric silsesquioxane (DSIPOSS). This open‐cage nanostructure silsesquioxane has 2 hydroxyl groups and therefore can be chemically built directly in the PU backbone to form hybrid polyurethane‐POSS foam. Synthesis procedure using polymeric 4,4′‐diphenylmethane diisocyanate, polyetherol, and DSIPOSS has been elaborated, and the influence of POSS on the cell structure, closed cell content, apparent density, thermal conductivity, and compression strength of the rigid polyurethane composites has been evaluated. The hybrid composite foams containing 1.5 and 2.0 wt% DSIPOSS showed a reduced number of cells and an increased average area of foam cells in comparison with the unmodified PU, while the addition of 0.5wt% of DSIPOSS causes an increase in the number of cells of the foam as compared with the reference and thus a reduction in the average area of cells. X‐ray microtomography provided data on the porous structure of polyurethane hybrid materials, including reduction of the pore surface area. Scanning electron microscopy and energy‐dispersive X‐ray spectroscopy analysis revealed a good homogenization of DSIPOSS in polyurethane matrix. Thermogravimetric analysis results have shown that incorporation of POSS nanoparticles into PU foam does not significantly change the degradation process. The compressive strength of PUF‐POSS hybrids in the direction parallel and perpendicular to the direction of foam rise is greater than the strength of the reference foam already for the lowest DSIPOSS content.     

Acylhydrazone-modified guar gum material for the highly effective removal of oily sewage

Oily sewage poses a serious environmental risk normally; thus, herein, the modified guar gum (GG-SH) was prepared through rapid condensation reaction between polysaccharide and stearic hydrazide. GG-SH exhibited high removal efficiency of crude oil, the maximum adsorption capacity was calculated to be 2157.3 mg?g-1. The kinetics and isotherm statistical theories showed that the sorption of crude oil onto GG-SH was governed by pseudo-second-order, and Langmuir models, respectively. The removal rate was still high after six cycles of regeneration, indicating an outstanding technique to prepare polysaccharide-based material for the oily sewage treatment with high efficiency and recyclability.     

Superhydrophobic and superoleophilic polyethylene aerogel coated natural rubber latex foam for oil-water separation application

The oil-water separation has made an attention due to over-increased production of oily water from the industrial process and everyday routine of humans. The current work reports on preparation and characterization of High-Density Polyethylene (HDPE) aerogel coated Natural Rubber Latex foam (NRLF) with superhydrophobic and superoleophilic character, good sorption capacity for oil-water separation application and were investigated. The HDPE aerogel and the coated NRLF material was prepared by a cooling process from a solution of HDPE in xylene solvent (HDPE sole, which resulted into thermally induced phase separation of the Polyethylene molecular network). The HDPE aerogel coated NRLF displayed a porous surface morphology with particle-like structural features. The HDPE aerogel coated NRLF showed superhydrophobicity with static water contact angle >150°. The effect and recyclability of the HDPE aerogel coated NRLF for oil-water separation was investigated using different model oil solvents to explore their repeatable application in oil spill clean-up process. Modified NRLF shows an excellent mechanical property (compressibility). The average modulus and average stiffness of the modified NRLF increased with the increase of the concentration of HDPE sol. The modified superhydrophobic sponge has good durability under acid and base conditions.     

Superparamagnetic Fe3O4@Alginate supported L-arginine as a powerful hybrid inorganic–organic nanocatalyst for the one-pot synthesis of pyrazole derivatives

Hybrid inorganic–organic material Fe₃O₄@Alg@CPTMS@Arg, was prepared by the layer-by-layer techniques through grafting l-arginine (l-arg) to Fe₃O₄@Alg using 3-chloropropyltrimethoxysilane (CPTMS) as a linker. Fe₃O₄@Alg was prepared by in situ co-precipitation of iron (iii) and iron (ii) chloride in the presence alginate (Alg). The hybrid inorganic–organic material was characterized employing various techniques such as Fourier transform infrared (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and vibrating sample magnetometer (VSM). The as-prepared Fe₃O₄@Alg@CPTMS@Arg nanoparticles mediated the synthesis of pyrazole derivatives with via one-pot reaction between phenylhydrazine, malononitrile, and various aromatic aldehydes under reflux in ethanol. Recycled catalyst exhibited comparable efficacy after seven cycles. The high catalytic activity, excellent yields, as well as the recyclability of the hybrid nanomaterials with quantitative efficiency, are factors that render this environmentally benign procedure appealing.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Mechanistic study of nanoparticles–surfactant foam flow in etched glass micro-models

This study was conducted in order to identify the pore-level mechanisms controlling the nanoparticles–surfactant foams flow process and residual oil mobilization in etched glass micro-models. The dominant mechanism of foam propagation and residual oil mobilization in water-wet system was identified as lamellae division and emulsification of oil, respectively. There was inter-bubble trapping of oil and water, lamellae detaching and collapsing of SDS-foam in the presence of oil in water-wet system and in oil-wet system. The dominant mechanisms of nanoparticles–surfactant foam flow and residual oil mobilization in oil-wet system were the generation of pore spanning continuous gas foam. The identified mechanisms were independent of pore geometry. The SiO₂-SDS and Al₂O₃-SDS foams propagate successfully in water-wet and oil-wet systems; foam coalescence was prevented during film stretching due to the adsorption and accumulation of the nanoparticles at the gas–liquid interface of the foam, which increased the films’ interfacial viscoelasticity.     

Experimental study of the influence of silica nanoparticles on the bulk stability of SDS-foam in the presence of oil

The influence of silica nanoparticles on the bulk stability of SDS-foam in the presence of oil was investigated in this study using KRÜSS dynamic foam analyzer. The bulk foam static stability was evaluated from half-decay time, liquid drainage, bubble size distribution, and change in total height and volume of the generated foams with respect to time. Results clearly showed that foam stability in the presence of oil mainly depends on the viscosity and density of the oil. Foam stability increased with the addition of silica nanoparticles due to the aggregation of the nanoparticles at the thin lamellae of the foam, which prevents spreading of the oil at the gas–liquid interface. Moreover, optimum foam stability was obtained with the modified nanosilica–SDS mixtures, while slower liquid drainage from the foam did not generally result in high foam stability.     

Laboratory investigation of biodegradability of a polyurethane foam under anaerobic conditions

Polyurethane (PU) foams can be used in many remediation applications as an isolation material to prevent the release of hazardous materials into the environment. The integrity of a PU foam was investigated in this study using short-term accelerated laboratory experiments including bioavailability assays, soil burial experiments, and accelerated bioreactors to determine the fate of PU foam in the soil where anaerobic processes are dominant. The experimental results have shown that the studied PU foam is likely not biodegradable under anaerobic conditions. Neither weight loss nor a change in the tensile strength of the PU material after biological exposure was observed. The FT-IR chemical signature of the PU foams was also nearly identical before and after biological exposure. The composition of the PU material (aromatic polyester and polyether PU) used in this study could have played a significant role in its resistance to microbial attack during the short-term accelerated experiments.     

羧甲基纤维素钠修饰的聚氨酯泡沫制备磁性吸油材料

采用聚氨酯泡沫为模板,依次修饰羧甲基纤维素钠(CMC)、Fe~(3+),在惰性气氛中高温热处理反应,制备多孔结构的磁性吸油材料.用光学显微镜、扫描电子显微镜、红外吸收光谱、X-射线衍射、接触角等技术对材料进行表征.详细考察了加热反应温度、CMC浓度和Fe~(3+)浓度对材料吸油性能和磁性的影响规律.实验表明,当加热反应温度选择230°C,CMC浓度为0.3 wt%,FeCl_3浓度为0.1 mol/L时,材料吸油性能最佳,对正己烷、二甲苯、环己烷、甲苯、乙酸乙酯、氯仿、机油、原油等有机溶剂和油类分子的吸附容量为10倍左右.磁性多孔材料具有明显的亲油、疏水特性,水的接触角达115.9°,同时材料密度只有0.036g/cm~3,能够漂浮于水面,实现对水面有机溶剂的快速吸附.吸附后的材料在外界磁场控制下,能够通过磁分离方式从水面快速分离.该材料具有良好的循环利用性能,可重复使用20次以上,吸油性能仍然保持良好.     

Mild and Selective Catalytic Hydrogenation of the C=C Bond in α,β‐Unsaturated Carbonyl Compounds Using Supported Palladium Nanoparticles

Chemoselective reduction of the C=C bond in a variety of α,β‐unsaturated carbonyl compounds using supported palladium nanoparticles is reported. Three different heterogeneous catalysts were compared using 1 atm of H₂: 1) nano‐Pd on a metal–organic framework (MOF: Pd⁰‐MIL‐101‐NH₂(Cr)), 2) nano‐Pd on a siliceous mesocellular foam (MCF: Pd⁰‐AmP‐MCF), and 3) commercially available palladium on carbon (Pd/C). Initial studies showed that the Pd@MOF and Pd@MCF nanocatalysts were superior in activity and selectivity compared to commercial Pd/C. Both Pd⁰‐MIL‐101‐NH₂(Cr) and Pd⁰‐AmP‐MCF were capable of delivering the desired products in very short reaction times (10–90 min) with low loadings of Pd (0.5–1 mol %). Additionally, the two catalytic systems exhibited high recyclability and very low levels of metal leaching.     

Effect of hydrophobically modified SiO2 nanoparticles on the stability of water-based SDS foam

In the present study, SiO₂ nanoparticles were first hydrophobically modified and then added into anionic surfactant sodium dodecyl sulfate (SDS) stabilized water-based foam to improve the foam stability. The foam stability was experimentally evaluated by measuring surface tension, Zeta potential and half-life of the foam. The foam stabilizing mechanism was also studied from a micro perspective by molecular dynamics simulation through analyzing the equilibration configuration and MSD curve of both SDS surfactant and water molecules. The results show that foam exhibits an optimal stability when SiO₂ concentration is 0.35 wt% under a specific surfactant concentration (0.5 wt%) in this work. The addition of SiO₂ nanoparticles with suitable concentration could improve the adsorption between SDS molecules and nanoparticles, thus limiting the movement of SDS and restricting the movement of surrounding water molecules, which is beneficial to enhance the foam stability.     

Preparation and properties of negative ion/polyurethane flexible foam composites

Abstract

In this study, negative ionpowder was modified with a silane coupling agent and then added to the polyurethane flexible foam to prepare NI/PU flexible foam composites by the one-step foaming method. The effects of the amount of negative ion powder on the mechanical properties, thermal properties and release of negative ions were investigated using scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and negative ion detectors. The SEM results showed that modified negative ion powder could be more uniformly distributed around the cell walls of the polyurethane flexible foam. The thermal stability, tensile strength and resilience of the NI/PU flexible foam composite were improved with the increase of the amount of modified negative ion powder. Increasing the amount of modified negative ion powder could also result in an increase in the release of negative ions, and it reached 5500/cm³ or higher at a negative ion content of 3%.     

Pd(II)-mediated triad multilayers with zinc tetrapyridylporphyrin and pyridine-functionalized nano-TiO2 as linkers: assembly, characterization, and photocatalytic properties

Triad hybrid multilayers containing the light sensitizers of zinc tetrapyridylporphyrin (ZnTPyP) and pyridine-functionalized TiO(2) (TiO(2)-Py) nanoparticles were constructed on substrate surfaces with the use of Pd(II) ions as the connectors using the layer-by-layer (LBL) method. The assembly process was monitored using ultraviolet-visible (UV-vis) absorption and X-ray photoelectron spectra as well as scanning electron microscopy and atomic force microscopy. The content of the pyridine substituents in the TiO(2)-Py nanocomposites was about 2% (w/w). The Soret absorption band of ZnTPyP was 24 nm red-shifted in the hybrid multilayers due to a strong intermolecular electronic coupling interaction among porphyrin macrocycles or porphyrin macrocycle/TiO(2)-Py nanoparticles. The average surface density of each ZnTPyP layer was about 1.4 × 10(-10) mol/cm(2). Aggregation of the small TiO(2)-Py nanoparticles to larger domains with sizes up to hundreds of nanometers occurred in the hybrid multilayers; however, such an aggregation behavior was weaker than that in the solutions. The quartz substrate modified with the as-prepared Pd/ZnTPyP/Pd/TiO(2)-Py triad hybrid multilayers was used as a heterogeneous photocatalyst for the degradation of methyl orange (MO) under irradiation (λ > 420 nm) at room temperature with a catalytic efficiency of about 1.3 × 10(-3) MO/ZnTPyP·s. Without the use of the filter, the catalytic efficiency increased because both ZnTPyP and TiO(2)-Py nanocomposites acted as the light sensitizers. It is suggested that the present heterogeneous catalyst has the advantages of facile separation, high stability, structural controllability on the molecular and nanoscale level, and good recyclability.     

Facile fabrication of asphaltene-derived graphene-polyurethane sponges for efficient and selective oil-water separation

Based on the natural graphene-structure in the raw asphaltene material, a graphene-polyurethane sponge (GPU) oil-absorption material was prepared via a facile and inexpensive route of dip-coated sponge carbonization, which used low-value petroleum asphlatene as the dip-coating reagent and polyurethane sponges as the template. The GPU presents high hydrophobic and super oleophilic properties, as well as the excellent oil absorption performance. And its chloroform absorption capacity could reach 123 times its original mass, which is significantly higher than that of most reported oil absorbents. Furthermore, the GPU exhibits good recyclability. It has the promising applications in the pollution control of spilt oil.     

A Dihomooxacalix[4]arene-gold nanohybrid based colorimetric sensor for sensitive and selective detection of iodide

Bidentate ureido-dihomooxacalix[4]arene based supramolecular hosts (n-propyl 1 and tert-butyl 2) were processed into organic nanoparticles via a bottom up approach in which a single step of re-precipitation was employed. These organic nanoparticles were then coupled with gold nanoparticles on the surface, resulting in an organic – inorganic hybrid framework (n-propyl H1 and tert-butyl H2). Photophysical studies of the organic nanoparticles and of the hybrid material were performed. The size and morphology were determined by TEM and DLS analysis. Moreover, the prepared hybrid frameworks were screened against various anions using UV-Visible absorption and fluorescence spectrophotometry. H1 exhibited ratiometric response towards iodide ion in aqueous medium, and colour change of the solution from pink to light blue was observed. This hybrid material selectively and sensitively detected iodide ion with detection limit of 8.3 nM and with almost no interference from other anions. H1 sensor ability was also tested with artificial and real urine samples. H2 showed different responses and no selectivity to any anion.