铈对超级双相不锈钢凝固组织的影响

研究了Ce对00Cr25Ni7Mo4N超级双相不锈钢凝固组织的影响,结果表明,随着钢中Ce含量的增加,其凝固组织中等轴晶线性比相应明显增加,Ce含量为0%,0.030%,0.047%,0.062%时,其等轴晶线性比分别为50%,60%,70%,77%。加Ce后钢中夹杂物为以Ce2O3为主、含有SiO2和MnO的复合夹杂,Ce2O3与δ-Fe具有较低的错配度,可作为形核核心提高形核率,增加了等轴晶比率。     

富铈混合稀土对AZ81合金组织与性能的影响

研究了富铈混合稀土对挤压铸造AZ81合金的显微组织和力学性能的影响。结果表明:加入不同含量富铈混合稀土的合金中都出现了一种新相Al11(Ce,La)3相,Al11(Ce,La)3相数量增多而Mg17Al12相则减少,能细化合金的组织晶粒,其细化作用在添加了1.5%富铈混合稀土的镁合金中尤为明显,但是当富铈混合稀土加入量大于2.0%时,合金中Al11(Ce,La)3相开始长大以粗大长杆状存在;在富铈混合稀土含量为1.5%时,AZ81合金的室温和150℃的综合力学性能达到最佳效果,超过2.0%时合金的室温和150℃综合力学性能开始下降;合金试样的拉伸断口带有局部韧窝的解理断裂和韧性断裂的混合特征。     

混合稀土对共晶Al-2%Fe合金组织形态的影响

研究了富La混合稀土对共晶Al-2?合金组织形态的影响. 当混合稀土加入量较少时, 合金中的α-Al相为明显的胞状枝晶;随着混合稀土加入量的增加, α-Al枝晶优先形核生长得到抑制, 共晶Al3Fe相得到细化;当稀土加入量增至0.6% (质量分数)共晶Al3Fe相尺寸逐渐增大. 并对混合稀土对共晶Al-2?合金组织形态的影响机制进行了探讨.     

镧、铈在WC-Co合金中赋存状态的研究

采用扫描电镜对高活性混合稀土掺杂的WC-8%Co-0.8%RE(RE:以La,Ce为主体的混合稀土)硬质合金的微观组织结构与合金烧结体表面进行了观察,采用元素面分布分析方法研究了合金中与合金烧结体表面La,Ce的结合状态.结果表明,合金中La,Ce处于原始结合状态,以细小第三相形式弥散分布于合金中;合金烧结体表面仅检测到呈不规则形状的含Ce氧化物的存在,La,Ce脱离了其原始结合状态,从而揭示了La,Ce结合状态的不稳定行为.通过考察掺杂前后合金Palmqvist断裂韧性的变化,对稀土相与WC硬质相、Co基固溶体粘结相之间的界面结合强度进行了间接评估.结果表明,合金中稀土相与合金中的其他两相之间具有较好的界面结合强度.     

铈对27%Cr超级铁素体不锈钢凝固组织影响机制研究

通过Factsage软件计算、宏观组织观察、扫描电镜分析等手段研究了Ce对27%Cr超级铁素体不锈钢凝固组织的影响。结果表明:未添加Ce钢中的夹杂物主要为Si-O-Mg-Al系夹杂及TiNb(CN)包裹Al_2O_3; Ce含量为0.05%时钢中形成弥散的高熔点Ce_2O_3和Ce_2O_2S,其作为非均质形核质点,使等轴晶比例增加,柱状晶变短变细,平均晶粒尺寸减小,凝固组织得到显著细化; Ce含量为0.07%时钢中的稀土化合物呈团簇状大量聚集。实验结果与Factsage计算预测基本吻合。     

纳米Y2O3/钴基合金激光熔覆层的组织

利用5 kW CO2激光器,在Ni基高温合金表面,熔覆纳米稀土氧化物(Y2O3)/钴基合金复合材料,制备了涂层.利用光学显微镜、扫描电镜及透射电镜分析了熔覆层的组织结构.结果表明: 熔覆层的主要相组成为γ-Co,ε-Co,Cr23C6和Y2O3;加入纳米Y2O3,凝固组织由细长的柱状树枝晶转变为较短的树枝晶;纳米Y2O3含量增大至1%时整个断面获得等轴晶组织;纳米Y2O3作为异质形核的核心,细化了组织;纳米Y2O3在熔覆层中分布不均匀,促进了γ-Co向ε-Co的转变;熔覆层的亚结构为堆跺层错.对熔覆层等轴组织形成机制进行了分析.     

铈对16Mn钢中夹杂物和组织的影响

在高温钼丝炉内向16Mn钢中加入不同含量的铈进行脱氧,分析了钢中夹杂物和组织的变化,并探讨了含铈夹杂物诱发晶内铁素体形核的机制.结果表明:随钢中铈含量的增加,夹杂物依次转变为CeAlO3,Ce2O2S和Ce2S3.经铈处理后,钢液在1873 K时保温300 s,夹杂物最为细小弥散.钢中晶内铁素体随铈含量的增加而增加,但最佳的铈含量约为0.032%(质量分数).钢中Ce2O2S和Ce2S3夹杂与α-Fe相之间的错配度分别只有1.2%和0.5%,均可作为IGF非常有效的形核核心,促进其形成.     

变质CH13钢中Ce_2O_3异质核心作用的研究

采用变质处理大大减弱了CH13钢枝晶组织的元素偏析 ,使未变质CH13钢中的晶界碳化物得以消除 ,CH13钢的冲击韧性大大提高。通过热力学计算及二维点阵错配度计算 ,并采用电子探针定量分析等手段 ,证实Ce2 O3型稀土夹杂物可作为CH13钢中初生奥氏体的异质核心 ,细化枝晶组织 ,减弱合金元素偏析     

变质CH13钢中Ce2O3异质核心作用的研究

变质变质处理大减弱了CH13钢技晶组织的元素偏析,使未变质CH13钢中的晶界碳化物得以消除,CH13钢的冲击韧性大大提高,通过热力学计算及二维点阵错配度计算,并采用电子探针定量分析等手段,证实Ce2O3型稀土夹杂物可作为CH13钢中初生奥氏体的异质核心,细化枝晶组织,减弱合金元素偏析。     

混合稀土对共晶Al-2％Fe合金组织形态的影响

研究了富La混合稀土对共晶Al-2％Fe合金组织形态的影响。当混合稀土加入量较少时，合金中的α—Al相为明显的胞状枝晶；随着混合稀土加入量的增加，α-Al枝晶优先形核生长得到抑制，共晶Al3Fe相得到细化；当稀土加入量增至0．6％(质量分数)共晶Al3Fe相尺寸逐渐增大。并对混合稀土对共晶Al-2％Fe合金组织形态的影响机制进行了探讨。     

镁含量对RE-Mg-Ni系A2B7型储氢合金结构与性能的影响

采用感应熔炼方法制备了La0.8-xGd0.2MgxNi3.1Co0.3Al0.1(x=0, 0.1, 0.15, 0.2, 0.25, 0.3, 0.4)储氢合金, 并在氩气气氛和1173 K下进行退火处理. 合金相结构分析结果表明, 镁含量(x)较低时合金以Ce2Ni7型为主相结构, A2B7型相丰度(Ce2Ni7+Gd2Co7)达到98.8%; 镁含量较高时合金相由A2B7型、 CaCu5型和PuNi3型物相构成, 随着镁含量的增加, PuNi3型和CaCu5型相组成逐渐增多, 其晶胞参数随Mg含量的增加而减小, 同时合金的吸氢平台也随之升高. 电化学测试结果表明, 随着合金中Mg含量增加, 合金电极的最大放电容量和循环稳定性均呈先增大后减小的规律, 其中x=0.15时合金电极具有最高的电化学放电容量(393 mA·h/g)和最佳的循环寿命(S100=92.82%). 合金电极的高倍率放电性能(HRD)随Mg含量的增加先减小再增大然后又减小, 适量的Mg元素改善了合金电极的动力学性能.     

La_2Ti_6O_(15)-CeTi_(21)O_(38)-PbTiO_3 ceramics formed in gaseous penetration of La-Ce into PbTiO_3 and their electric properties

PbTiO3 ceramics, which are typical ferroelectric materials, are useful in various applied fields. For example, it has a very good candidacy for piezoelectric materials for high temperature and high sensibility. In recent years, the studies on doped PbTiO3 ceramics have received consid-erable attention[1—3]. The modified PbTiO3 ceramics doped with Ca2+, Sm3+, Y3+, Ce4+ etc. have some better properties: their Curies temperature decreases, their tetragonal distortion degree de-grades and th…     

助剂对甲烷部分氧化制合成气镍基催化剂性能的影响

考察了添加助剂铈、镧和钙对镍基催化剂反应性能的影响，发现助剂对以α-Al2O3为载体的镍基催化剂的调变作用比以γ-Al2O3为载体的镍基催化剂好，且助剂铈对催化剂的性能改善最好。在此基础上，研究了不同载量的铈对催化剂性能的影响。结果表明，铈的质量分数为1%时对催化剂的性能改善最好。同时采用XRD、XPS、TG等技术，研究了助剂铈对10％Ni/γ-Al2O3催化剂的改性作用。XRD分析表明，铈负载量较低时，催化剂中的CeO2高度分散在催化剂表面，铈负载量较高时，CeO2形成微晶颗粒，降低了催化活性。     

Two-dimensional lanthanide heteropolyvanadates of manganese(IV) and nickel(IV) containing two types of heteropoly anions with 1:13 and 1:12 stoichiometry

Reactions of 1:13 heteropoly anions [MV13O38](7-) (M = Mn, Ni) and lanthanide cations Ln3+ (Ln = La, Ce, or Pr) produce five isomorphic compounds, which are crystallized in the triclinic crystal system, space group P1, and formulated as [Ln6(H2O)25(MV12O38)(HMV13O38)].nH2O ((1) Ln = La, M = Mn, and n approximately 31; (2) Ln = Ce, M = Mn, and n approximately 29; (3) Ln = Pr, M = Mn, and n approximately 31; (4) Ln = La, M = Ni, and n approximately 28; (5) Ln = Pr, M = Ni, and n approximately 33). These compounds are two-dimensional polymeric structures constructed by hydrated lanthanide cations and two types of heteropoly anions, [MV13O38](7-) and [MV12O38](12-). In contrast to the previous reported 1:13 heteropoly anions, all with disordered structures, [MV13O38](7-) clusters in 1-5 are non-disordered with a distinct mode. The second kind of anionic cluster [MV12O38](12-) with O(h) symmetry, which consists of 13 entire edge-sharing MO(6) (M = V, Mn or Ni) octahedra, has not been reported hitherto. The emergence of the new cluster may be correlated to the six capping lanthanide cations surrounding it with a stabilization effect. In this paper, the syntheses and structures of the five polymeric lanthanide heteropolyvanadates of manganese(IV) and nickel(IV) have been presented.     

La-Ce-Cu系列催化剂SO2中毒机理研究

采用NH_4NO_3共熔法合成La－Ce－Cu系列样品，并通过XRD分析了样品的相组成。XRF证明了系列样品组成均为氧缺陷型化合物．用TEM研究了样品的表面结构，发现随着SO_2中毒的加深，Cu向表面偏析与S结合生成新的化合物，导致了原晶体结构的变形，同时证明纯CeO_2不发生S中毒．XPS研究表明：样品La_(.029)Ce_(0.57)Cu_(0.14)O_x中毒后Cu从La_2CuO_4中分解出来并与S结合生成CuSO_4；相应的CeO_2参与了中毒反应，生成Ce_2O_3,整个中毒反应如下：La_2CuO_4＋2CeO_2＋SO_2＝CuSO_4＋La_2O_3＋Ce_2O_3     

夹杂物在中高碳钢堆焊金属中成为初生奥氏体非均质形核核心的探讨

采用二维点阵错配度理论,对不同稀土 杂物和中高碳钢堆焊时常见氧化物在熔敷金属中成为初生奥氏体非均质形核核心的有效性进行了分析和计算。成为熔敷金属中初生奥氏体非均质开核核心的夹物以Ｃｅ２Ｏ３．Ｌａ２Ｏ３和Ｃｅ２Ｃ２Ｓ为效,Ａ１２Ｏ３,ＳｉＯ２,ＭｎＯ和ＣｅＳ为无效。     

纳米La0.8A’0.2Mn1-xCuxO3（A’=Ce and/or Sr）的制备、表征及其高效催化NO+CO的性能研究

采用柠檬酸-溶胶凝胶法制得钙钛矿型复合氧化物La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),La0.8Sr0.2Mn0.6Cu0.4O3,La0.8Ce0.1Sr0.1Mn0.6 Cu0.4 O3,并采用X射线衍射(XRD)、扫描电镜(SEM)、比表面积(BET)、X射线光电子能谱(XPS)对其进行表征,测试了复合氧化物对CO+NO的催化活性。结果表明:La0.8Ce0.1Sr0.1Mn0.6Cu0.4O3催化活性最好,150℃时CO转化率91.8%,300℃时NO转化率100%;对于La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),比表面积和颗粒的大小及分散度是影响催化活性的主要因素;对于La0.8Ce0.2Mn0.6Cu0.4O3,La0.8 Sr0.2 Mn0.6 Cu0.4 O3,La0.8 Ce0.1 Sr0.1 Mn0.6 Cu0.4 O3,催化剂的组成是影响催化活性的关键因素。     

Two-phase synthesis of colloidal annular-shaped Ce(x)La(1-x)CO3OH nanoarchitectures assembled from small particles and their thermal conversion to derived mixed oxides

Undoped and cerium doped LaCO(3)OH annular-shaped nanoarchitectures with high specific surface area have been fabricated via the thermolysis of Ce(x)La(1-x)(oleate)(3) (x = 0-20 mol %) complexes in a toluene-water system containing tert-butylamine/oleylamine. The products exhibit 400 nm-sized monodisperse annular-shaped nanoarchitectures, which are constituted of 3-5 nm-sized primary particles. A possible mechanism of the reaction of Ce(x)La(1-x)(oleate)(3) and tert-butylamine for the formation of annular-shaped Ce(x)La(1-x)CO(3)OH nanoarchitectures is proposed. The thermal conversion of Ce(x)La(1-x)CO(3)OH to Ce(x)La(1-x)(CO(3))O(2) at 600 °C, to Ce(x)La(1-x)(OH)(3) at 800 °C, final to (Ce(x)La(1-x))(2)O(3-δ) at 900 °C were employed, while the original morphology was essentially unchanged. The dopant concentration was varied from 5 to 20 of cerium ions per LaCO(3)OH nanoparticle. The X-ray diffraction (XRD) results reveal that the cerium dopant could enter easily into the LaCO(3)OH structural lattice, whereas copper could unlikely enter into their lattice because of their large ionic radius difference. The cerium oxidation state was controlled by changing doping concentration. The X-ray photoelectron spectroscopy (XPS) results reveal that only one Ce(3+) oxidation state is in the as-synthesized Ce(x)La(1-x)CO(3)OH samples with cerium concentration ranging from 5 to 20 mol %, whereas both 3+ and 4+ ones coexisted in 20 mol % Ce:LaCO(3)OH structure. Remarkable luminescence emission intensity enhancement of 1.5-9.0 times were observed for Ce(x)La(1-x)CO(3)OH samples with cerium concentration ranging from 5 to 20 mol %, after doping with an undoped LaCO(3)OH.     

Composition-structure relationships in polar intermetallics: experimental and theoretical studies of LaNi(1 + x)Al(6 - x) (x = 0.44)

A new ternary aluminide, LaNi(1 + x)Al(6 - x ) (x = 0.44), has been synthesized from La, Ni, and Al in sealed silica tubes. Its structure, determined by single-crystal X-ray diffraction, is tetragonal P4/mmm (No. 123) with Z = 1 and has the lattice parameters a = 4.200(8) and c = 8.080(8) angstroms. Refinement based on Fo2 yielded R1 = 0.0197 and wR2 = 0.020 [I > 2sigmaI]. The compound adopts a structure type previously observed in SrAu2Ga5 and EuAu2Ga5. The atomic arrangement is closely related to the one in BaAl4 as well as in other rare-earth gallide compounds such as LaNi0.6Ga6, HoCoGa5, Ce4Ni2Ga20, Ce4Ni2Ga17, Ce4NiGa18, and Ce3Ni2Ga15. This structure exhibits a large open cavity which may be filled by a guest atom. Band structure calculations using density functional theory have been carried out to understand the stability of this new compound.     

Ni-Cu/La2O3催化剂上甲烷部分氧化制合成气

用浸渍法制备了不同Cu质量分数的Ni Cu/La2O3双金属催化剂，考察了金属浸渍顺序和Cu质量分数对催化剂甲烷部分氧化性能的影响,并通过BET、XRD、TPR和SEM等技术对催化剂进行了表征。结果表明,在甲烷部分氧化制合成气反应中，Cu助剂的添加对Ni/La2O3催化剂的活性有一定的改进作用，其中浸渍顺序对催化剂的性能影响很大，共浸渍制备的催化剂活性相对较好；Cu质量分数为5%~7%时催化剂有较好的活性和稳定性；XRD等测试表明,Cu和Ni金属由于相同的晶型结构及离子半径在制备过程中形成了双金属固溶体，提高了活性组分Ni的分散度，减少了Ni晶粒的烧结聚集长大，从而提高了催化剂的活性和稳定性。