顺丁橡胶／低密度聚乙烯的共混

比较了未交联和动态交联不同组成PB/LDPE共混物的力学性能。共混物的T_g、T_m和T_d不随组成而变化,表明PB和LDPE不具有相容性。但共混物中PE的γ转变向高温方向位移,说明PE非晶部分的分子短链和PB有界面相互作用。形态研究表明,未交联体系中量多的组份形成连续相,动态交联体系在PB/LDPE≤70/30时,PE呈连续相,交联的PB为分散相。     

端羟丁腈聚氨酯/聚甲基丙烯酸甲酯互穿网络高聚物的T_g和形态研究——Ⅱ.化学相容性的影响

用动态力学和透射电镜的方法,研究了化学相容性对丁腈羟聚氨酯/聚甲基丙烯酸甲酯互穿网络高聚物[PU(HTBN)/PMMA-IPN]的T_g转变行为和形态的影响。适当地提高端羟丁腈(HTBN)中氰基含量或加入合适的链延伸剂或共聚单体,可得到半相容的体系。丙烯腈含量为24.3％时,相区尺寸约为200?,在—20—+130℃范围内的Tanδ值均在0.2—0.3。由于极性基的相互作用,聚氯醚聚氨酯[PU(PCE)]/PMMA IPN具有更微细的相结构及单一的T_g转变,其Tanδ峰值为1.6。     

尼龙短纤维/白炭黑填充天然橡胶的流变与动态力学行为

以尼龙短纤维(NSF)增强天然橡胶(NR)混炼胶为研究体系,以马来酸酐接枝天然橡胶(MNR)为增容剂,考察增容剂、NSF含量对NR/NSF母胶动态流变行为的影响;将NR/NSF母胶加入30份白炭黑(Si O2)填充NR混炼胶中,对比研究NR/NSF、NR/NSF/Si O2混炼胶的线性与非线性流变行为及动态力学行为,采用修正的两相模型分析"粒子相"的增强作用,探讨硫化胶储能模量E'和损耗因子tanδ的变化.结果表明,MNR影响NSF在基体中的分散性和NSF/NR混炼胶的动态流变行为;高填充Si O2和少量NSF之间存在协同增强作用,使NR/NSF/Si O2混炼胶的补强因子和应变放大因子均高于NR/NSF混炼胶,显著增加"粒子相"的黏性与弹性贡献,限制"粒子相"的松弛;硫化胶的E'和tanδ峰值随NSF体积分数增加分别升高和降低.     

RE-C22/NR复合材料的机械性能和动态力学性能

通过沉淀法合成RE-C22配合物(RE代表La,Sm和Gd元素;C22代表C_(22)H_(34)O_6),分两步进行:用氢氧化钠中和C22,然后用RE盐酸盐进行双分解反应,沉淀出RE-C22配合物。通过红外光谱(IR)测定RE-C22配合物的结构。RE-C22配合物和天然橡胶(NR)通过共混制备得到RE-C22/NR复合材料。在160℃进行硫化,交联密度测量结果显示总交联密度随着RE-C22含量的增加而增加。分别研究了复合材料流变性能,静态和动态力学性能以及表面形貌。结果表明,RE-C22作为多功能填料可以加速交联过程中硫磺的硫化,并增强NR的物理力学性能。     

TBIR应用于航空胎侧胶的热氧老化性能

研究了反式-1,4-丁二烯-异戊二烯共聚橡胶(TBIR)应用于航空轮胎胎侧胶[天然橡胶(NR)/顺丁橡胶(BR)/TBIR]的耐热氧老化性能. 结果表明, 与NR/BR硫化胶相比, 10~20份质量的TBIR取代BR后, NR/BR/TBIR硫化胶的交联密度明显提高, 压缩温升降低2.2~3.4 ℃, 耐屈挠疲劳性能提高约100%, 填料分散性改善, 填料团聚体体尺寸减小, 拉伸性能基本不变. 随热氧老化时间延长, 硫化胶的交联密度先增加后降低, 并用TBIR的硫化胶交联密度在老化48 h后趋于平缓. 与NR/BR相比, 老化后的NR/BR/TBIR硫化胶生热最低, 耐屈挠疲劳性最高.     

聚甲基丙烯酸β羟乙酯在聚乙烯膜上辐射接枝物的形态结构

本文用透射电子显微镜(TEM),光学显微镜(OM),小角X射线散射(SAXS)等方法研究了聚甲基丙烯酸β羟乙酯(HEMA)在聚乙烯(PE)膜上辐射接枝物的形态结构.观察了微相结构随接枝条件变化规律.HEMA为支链的接枝共聚物的基本形态是高度分散的HEMA微区(约几百A)存在于PE连续相中的两相体系.随接枝量增加,微区形态发生变化.SAXS结果进一步证实了接枝共聚物相分离的形态结构,并利用Tsvankin-Buchanan公式计算了共聚物的长周期、无定形层厚及一维结晶度.     

高反式-1,4-丁二烯-异戊二烯共聚橡胶在轿车轮胎带束层中的应用研究

研究了高反式-1,4-丁二烯-异戊二烯共聚橡胶(TBIR)的生胶性能及其在轿车轮胎带束层中的应用。结果表明,随丁二烯单体单元含量增加,TBIR生胶的玻璃化转变温度、结晶熔融焓、生胶强度和硬度逐渐降低。硫化胶性能测试表明,TBIR硫化胶的定伸应力、回弹性能以及耐老化性能优于NR硫化胶,TBIR-40硫化胶的拉伸强度和撕裂强度明显高于NR硫化胶。采用10~30份TBIR取代NR应用于轿车轮胎带束层配方,并用硫化胶拉伸强度、拉断伸长率、撕裂强度和钢丝帘线抽出力处于较高水平,定伸应力、硬度、回弹性能和耐老化性能较对比胶提高,含TBIR的轮胎带束层胶料具有更加优异的综合性能。DMA结果表明,NR与TBIR相容性较好,NR/TBIR并用硫化胶具有更低的内耗。TEM结果表明,NR/TBIR并用胶具有较好的填料分散性。     

聚醋酸乙烯酯/聚丙烯酸甲酯互穿网络聚合物的研究——Ⅱ.强迫互容效应及形态结构

用分步法合成了交联密度不同的聚醋酸乙烯酯/聚丙烯酸甲酯互穿网络聚合物(PVAc/PMA-IPN),用DMS,TEM和SAXS等方法进行表征。发现随交联密度的增加,体系的T_g,转变由两个逐渐变为一个,清楚显示出强迫互容的贡献。模量实验值与Davies方程计算值的比较表明,所研究的IPN是一个双相连续体系,相区尺寸约为100。     

双组份网状共聚物的动态力学性质

本文研究了端乙烯基聚氨酯预聚物(VTPU)同乙烯类单体甲基丙烯酸甲酯(MMA)、苯乙烯(St)、醋酸乙烯酯(VAc)、和甲基丙烯酸丁酯(BMA)聚合得到的双组份网状共聚物(BCN′s)的动态力学性能及形态结构。四种BCN′s试样两组份在动态力学谱上均有半相容的特征。体系的交联密度增大,混合熵增加,相容性改善,试样中可溶性组份含量随BCN′s的组成而变化。溶胶组份可改善体系中两组份的相容性。     

聚对苯二甲酸乙二酯的玻璃化转变和结晶化的正电子湮没研究

研究了聚对苯二甲酸乙二酯的玻璃化转变和结晶过程对正电子湮没寿命谱的影响.结果表明,结晶过程对正电子湮没的长寿命组份τ_3的寿命值不敏感,用这种方法测得的“T_g”不随结晶度而变化,而长寿命组份的相对强度则随结晶度的增加而减小.     

改性合成橡胶在轮胎工业中的应用

介绍了几种合成橡胶的改性在轮胎工业中的应用现状。为了提高轮胎的综合行驶性能 ,近年来国外开发出了性能良好的溶聚丁苯、Nd系顺丁、乙烯基顺丁、3,4-异戊胶、卤化丁基胶、苯乙烯 -异戊二烯 -丁二烯橡胶、星型支化丁基胶及溴化三元乙丙胶等一系列改性合成橡胶新品种     

Blending of Natural Rubber/Recycled Ethylene-Propylene-diene Rubber: Promoting the Interfacial Adhesion Between Phases by Natural Rubber Latex

This article deals with blends based on natural rubber (NR) and recycled ethylene-propylene-diene rubber (R-EPDM). Natural rubber latex (NRL) was introduced into the blends to enhance interfacial adhesion between NR and R-EPDM. A new route of compounding was also suggested. The blends were prepared by mixing R-EPDM and other additives in NRL before blending with natural rubber on a two-roll mill. By applying this method, the homogeneity of the blends and cross-linking distribution are significantly improved. The blends exhibited superior state of cure, swelling resistance, mechanical properties and dynamic mechanical properties. The degree of entanglement between NR and R-EPDM also increased after NRL modification.     

Comparative study of natural rubber and acrylonitrile rubber reinforced with aligned short aramid fiber

The aims of this paper are three-fold. The first is to determine the reinforcement of high performance short aramid fiber in two representative rubber matrices, namely natural rubber and acrylonitrile rubber. The second is to ascertain the effect of rubber polarity on the reinforcement. The third is to establish a pattern of reinforcement for use with less studied fibers. The rubbers were reinforced either with only aramid fiber or with a hybrid of aramid fiber and carbon black. The fiber contents were varied at 0, 2, 5 and 10 parts (by weight) per hundred rubber (phr) while those of carbon black were 0, 10, 20 and 30 phr. Conventional sulfur vulcanization was used. It was found that aramid fiber can reinforce both rubbers in the low strain region effectively, although to a significantly different degree. The hybrid carbon black provides additional reinforcement at low to medium strains and allows high strain stress upturn to occur in both rubber matrices. The findings enable the preparation of rubber composites having a wide, controllable range of mechanical behavior for specific high-performance engineering applications. Significantly, they also serve as a benchmark for developing reinforced systems from alternative fibers, particularly those from natural sources.     

Preparation of high damping elastomer with broad temperature and frequency ranges based on ternary rubber blends

Based on the blends of chlorinated butyl rubber (CIIR), nitrile butadiene rubber (NBR) and chloroprene rubber (CR), a kind of high damping elastomer with broad temperature and frequency ranges is prepared. CIIR/NBR binary blend is prepared to take advantage of the immiscibility and the large difference in cross‐link density of the different phases caused by the curatives and accelerators migration. The dynamic mechanical analysis reveals that the binary blend was immiscible and its loss factor (tanδ) versus temperature curves show two separated and expanded loss peaks when compared with those of pure cured CIIR and NBR. In order to improve its damping properties at room temperature, the third component CR with the polarity between CIIR and NBR was blended into the binary blend. The resulted CIIR/NBR/CR ternary blend has gained effective damping properties (tanδ > 0.3) in the temperature range of ?86.4 to 74.6°C and the frequency range of 10^?2 to more than 10⁹ Hz. Other effects on the damping properties of the ternary rubber were also studied. Copyright © 2013 John Wiley & Sons, Ltd.     

A critical review on analytical methods and characterization of butyl and bromobutyl rubber

The molecular structure characterization of butyl and bromobutyl rubber (BIIR) requires the definition of three main parameters: (I) the unsaturation degree of the rubbers, (II) the total bromine content of the BIIRs, and (III) the functional bromine content of the BIIRs. The analytical methods for the determination of the previously mentioned parameters have been described and critically examined in this review.     

异苯橡胶和环化异苯橡胶结构表征

异苯橡胶和环化异苯橡胶结构表征孙晓日，李大珍，余尚先（山东昌潍师范专科学校化学系山东潍坊２６１０１３）（北京师范大学化学系北京１００８７５）关键词异苯橡胶，环化异苯橡胶，结构异戊二烯与苯乙烯无规共聚或嵌段共聚得到异苯橡胶已有不少研究和报导￣［１，２］...     

Preparation of hydrogenated nitrile rubber using palladium acetate catalyst: Its characterization and kinetics

Hydrogenated nitrile rubber was prepared by using palladium acetate as the homogeneous catalyst system. The effect of different reaction parameters on the level of hydrogenation was studied. The extent of hydrogenation increased with increase in reaction time, temperature, pressure, and catalyst concentration. A maximum conversion of 96% could be achieved. The degree of hydrogenation was estimated from IR and NMR spectroscopy. The selectivity of the catalyst in reducing ? C?C? in presence of ? C?N was supported by IR and ¹³C-NMR spectra. ESCA studies further confirmed this observation. Properties of hydrogenated nitrile rubber were investigated by various techniques such as gel permeation chromatography (GPC), glass transition temperature (T_g), stress-strain behavior and rheological measurements. GPC studies showed no significant change in molecular weights of the products after the reaction. T_g value decreased with an increase in the level of hydrogenation. The ultimate stress improved significantly with the increase in the extent of hydrogenation. The die swell decreased with hydrogenation at a particular shear rate. The kinetics of the NBR hydrogenation were investigated. With the increase of the hydrogen pressure and catalyst concentration, the rate of the reaction increased. The reaction was apparently first order with respect to olefinic substrate at higher hydrogen pressure. The apparent activation energy, enthalpy, and entropy of the reaction were calculated as 29.9 kJ/mol, 27.42 kJ/mol, and –0.20 kJ mol^?1 K^?1, respectively.     

木质素增强丁苯橡胶复合材料研究

采用木材水解木质素为原料,均匀溶解在碱性溶液中,与天然橡胶复合形成互穿网络结构,再通过共沉淀法制得一种木质素/天然橡胶复合物。采用该复合物部分代替商用橡胶补强剂——白炭黑,通过三段混炼法对丁苯橡胶进行混炼。结果表明,这种木质素/天然橡胶复合物对丁苯橡胶具有一定的补强作用,其拉伸强度及断裂伸长率均得到一定改善;而热机械性能研究发现,该复合物部分代替白炭黑后,橡胶材料的滚动阻力及耐寒性均得到改善,但抗湿滑性能有一定程度下降。     

Hysteresis loss as a measure of metal–rubber adhesion

As in the case of reinforcing filler-induced increase in hysteresis in rubbers, placement of aluminum (A1) foil to the surface of a rubber blend of epichlorohydrin rubber and carboxylated nitrile base induces increased hysteresis of the rubber due to adhesion between Al and the rubber blend. Changes in hysteresis loss due to Al foil can be correlated with the peel strength of Al-rubber-Al joints. © 1995 John Wiley & Sons, Inc.