Enhanced reversible lithium storage in a nanosize silicon/graphene composite

Si/graphene composite was prepared by simply mixing of commercially available nanosize Si and graphene. Electrochemical tests show that the Si/graphene composite maintains a capacity of 1168 mAh g^?1 and an average coulombic efficiency of 93% up to 30 cycles. EIS indicates that the Si/graphene composite electrode has less than 50% of the charge-transfer resistance compared with nanosize Si electrode, evidencing the enhanced ionic conductivity of Si/graphene composite. The enhanced cycling stability is attributed to the fact that the Si/graphene composite can accommodate large volume charge of Si and maintain good electronic contact.     

Fabrication of porous carbon/Si composite nanofibers as high-capacity battery electrodes

Carbon/Si composite nanofibers with porous structures are prepared by electrospinning and subsequent carbonization processes. It is found that these porous composite nanofibers can be used as anode materials for rechargeable lithium-ion batteries (LIBs) without adding any binding or conducting additive. The resultant anodes exhibit good electrochemical performance; for example, a large discharge capacity of 1100 mAh g^?1 at a high current density of 200 mA g^?1.     

Electrochemical performance of nanocomposite LiMnPO4/C cathode materials for lithium batteries

A LiMnPO₄/C composite cathode was prepared by a combination of spray pyrolysis and wet ball milling. The cathode showed stable performance at various cutoff voltages up to 4.9 V. The cutoff voltage increase up to 4.9 V allowed the achievement of a high discharge capacity in galvanostatic charge–discharge tests. The discharge capacities of 153 mAh g^?1 at 0.05 C and 149 mAh g^?1 at 0.1 C were achieved at room temperature; the trickle-mode discharge capacities at room temperature were 132, 120 and 91 mAh g^?1 at 0.1, 1 and 5 C discharge rates, respectively. The cell exhibited a good rate capability in the galvanostatic cycling up to 5 C discharge rates at both ambient temperature and 50 °C.     

Fabrication and electrochemical properties of the Sn–Ni–P alloy rods array electrode for lithium-ion batteries

A new ternary Sn–Ni–P alloy rods array electrode for lithium-ion batteries is synthesized by electrodeposition with a Cu nanorods array structured foil as current collector. The Cu nanorods array foil is fabricated by heat treatment and electrochemical reduction of Cu(OH)₂ nanorods film, which is grown directly on Cu substrate through an oxidation method. The Sn–Ni–P alloy rods array electrode is mainly composed of pure Sn, Ni₃Sn₄ and Ni–P phases. The electrochemical experimental results illustrate that the Sn–Ni–P alloy rods array electrode has high reversible capacity and excellent coulombic efficiency, with an initial discharge capacity and charge capacity of 785.0 mAh g^?1 and 567.8 mAh g^?1, respectively. After the 100th discharge–charge cycling, capacity retention is 94.2% with a value of 534.8 mAh g^?1. The electrode also performs with an excellent rate capacity.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

The amorphous Mg–Al–Ni composites were prepared by mechanical ball-milling of Mg₁₇Al₁₂ with x wt.% Ni (x = 0, 50, 100, 150, 200). The effects of Ni addition and ball-milling parameters on the electrochemical hydrogen storage properties and microstructures of the prepared composites have been investigated systematically. For the Mg₁₇Al₁₂ ball-milled without Ni powder, its particle size decreases but the crystal structure does not change even the ball-milling time extending to 120 h, and its discharge capacity is less than 15 mAh g^?1. The Ni addition is advantageous for the formation of Mg–Al–Ni amorphous structure and for the improvement of the electrochemical characteristics of the composites. With the Ni content x increasing, the composites exhibit higher degree of amorphorization. Moreover, the discharge capacity of the composite increases from 41.3 mAh g^?1 (x = 50) to 658.2 mAh g^?1 (x = 200) gradually, and the exchange current density I₀ increases from 67.1 mA g^?1 (x = 50) to 263.8 mA g^?1 (x = 200), which is consistent with the variation of high-rate dischargeability (HRD). The ball-milled Mg₁₇Al₁₂ + 200 wt.% Ni composite has the highest cycling discharge capacity in the first 50 cycles.     

Binder-free porous core–shell structured Ni/NiO configuration for application of high performance lithium ion batteries

An interwoven core–shell structured Ni/NiO anode for lithium ion batteries was created by a simple oxidation of Ni foam. As-prepared configuration has a high specific discharge capacity of 701 mAh g^?1 at the 2nd cycle. Its electrochemical performance at subsequent cycles shows good energy capacity of 646 mAh g^?1 at the 65th cycle as well as good rate capability. The porous core–shell structure not only buffers the volume change during cycling but also effectively increases the contact among anode, current collector and electrolyte. The small contact resistance between NiO and Ni facilitates enhanced intrinsic kinetics from conversion reaction.     

An understanding of anomalous capacity of nano-sized CoO anode materials for advanced Li-ion battery

Nanostructured transition metal oxides are of great interest as a new generation of anode materials for high energy density lithium-ion batteries. In this work, research has been focused on the nano-sized (grain size ～7 nm) CoO anode material and this material delivers charge capacity of 900 mAh g^?1 that exceeds the theoretical value of 715 mAh g^?1. Possible reason for this unaccounted and unexplained anomalous capacity of the nano-sized CoO material has been suggested by thermogravimetric analysis. A mechanism for this interesting behavior has been systematically evaluated by using X-ray absorption spectroscopy. The anomalous capacity is proposed to be associated with the formation of oxygen-rich CoO material. The results obtained from the nano-sized CoO material have been compared with relatively larger-sized material (grain size ～32 nm).     

High capacity and excellent cyclability of vanadium (IV) oxide in lithium battery applications

A VO₂ · 0.43H₂O powder with a flaky particle morphology was synthesized via a hydrothermal reduction method. It was characterized by scanning electron microscopy, electron energy loss spectroscopy, and thermogravimetric analysis. As an electrode material for rechargeable lithium batteries, it was used both as a cathode versus lithium anode and as an anode versus LiCoO₂, LiFePO₄ or LiNi_0.5Mn_1.5O₄ cathode. The VO₂ · 0.43H₂O electrode exhibits an extraordinary superiority with high capacity (160 mAh g^?1), high energy efficiency (95%), excellent cyclability (142.5 mAh g^?1 after 500 cycles) and rate capability (100 mAh g^?1 at 10 C-rate).     

Incorporation of MWCNTs into leaf-like CuO nanoplates for superior reversible Li-ion storage

CuO/MWCNT nanocomposite is prepared by a simple precipitation method. The MWCNTs are incorporated into the leaf-like CuO nanoplates and build up a network to connect the CuO nanoleaves. The as-prepared CuO/MWCNT exhibits superior reversible Li-ion storage, the capacity maintains 627 mAh g^? 1 at 60 mA g^? 1 even after 50 cycles. The improved capability is ascribed to the MWCNT network in the composite, which improves the electrical contact of CuO/CuO and CuO/current collector, facilitates the charge transfer on CuO/electrolyte interfaces, and compensates the volume change of CuO during cycling.     

Nanocrystalline MnO thin film anode for lithium ion batteries with low overpotential

Nanocrystalline MnO thin film has been prepared by a pulsed laser deposition (PLD) method. The reversible lithium storage capacity of the MnO thin film electrodes at 0.125C is over 472 mAh g^?1 (3484 mAh cm^?3) and can be retained more than 90% after 25 cycles. At a rate of 6C, 55% value of the capacity at 0.125C rate can be obtained for both charge and discharge. As-prepared MnO thin film electrodes show the lowest values of overpotential for both charge and discharge among transition metal oxides. All these performances make MnO a promising high capacity anode material for Li-ion batteries.     

Hierarchically ordered porous nickel oxide array film with enhanced electrochemical properties for lithium ion batteries

Hierarchically ordered porous nickel oxide array film was prepared by electrodeposition through monolayer polystyrene spheres template. The as-prepared film had a highly porous structure of interconnected macrobowls array possessing nanopores. As anode material for lithium ion batteries, the porous array NiO film exhibited weaker polarization, higher coulombic efficiency and better cycling performance in comparison with the dense NiO film. After 50 cycles, the discharge capacity of porous array NiO film was 518 mAh g^? 1 at 1 C rate, higher than that of the dense NiO film (287 mAh g^? 1). The enhancement of the electrochemical properties was due to the unique hierarchical porous architecture, which provided fast ion/electron transfer and alleviated the structure degradation during the cycling process.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

Preparation and electrochemical characterization of the porous sulfur cathode using a gelatin binder

A novel porous sulfur cathode in which a gelatin was used as the binder was prepared by using a freeze–drying method at −58 °C. The porous structure provides channels for electrolyte infiltration and then facilitates ion diffusion. This porous sulfur cathode has a high initial capacity of 1235 mAh g⁻¹ and a high reversible capacity of 626 mAh g⁻¹ after 50 cycles, both of which are higher than that of the normal cathodes with compact structures.     

Improved electrochemical performances of core-shell Cu2O/Cu composite prepared by a simple one-step method

Core-shell Cu₂O/Cu composites were successfully prepared by over-reduction of aqueous CuSO₄ with hydrazine hydrate as reductant. Field emission scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM) clearly illuminate that the core is Cu₂O with 400 nm in diameter, and the shell is Cu with about 50 nm in thickness. The core-shell Cu₂O/Cu exhibited weaker polarization and higher coulombic efficiency than pure octahedral Cu₂O, especially in the initial stage of cycles. After 50 cycles, the reversible capacity of Cu₂O/Cu (360 mAh g^?1) was much higher than that of pure Cu₂O (160 mAh g^?1). The improvement of electrochemical properties is attributed to the core-shell structure of Cu₂O/Cu and the catalytic effect of Cu on the decomposition of Li₂O during the charging process.     

Fabrication and electrochemical performance of nickel ferrite nanoparticles as anode material in lithium ion batteries

Nano-sized nickel ferrite (NiFe₂O₄) was prepared by hydrothermal method at low temperature. The crystalline phase, morphology and specific surface area (BET) of the resultant samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and nitrogen physical adsorption, respectively. The particle sizes of the resulting NiFe₂O₄ samples were in the range of 5–15 nm. The electrochemical performance of NiFe₂O₄ nanoparticles as the anodic material in lithium ion batteries was tested. It was found that the first discharge capacity of the anode made from NiFe₂O₄ nanoparticles could reach a very high value of 1314 mAh g⁻¹, while the discharge capacity decreased to 790.8 mAh g⁻¹ and 709.0 mAh g⁻¹ at a current density of 0.2 mA cm⁻² after 2 and 3 cycles, respectively. The BET surface area is up to 111.4 m² g⁻¹. The reaction mechanism between lithium and nickel ferrite was also discussed based on the results of cycle voltammetry (CV) experiments.     

Net-structured NiO–C nanocomposite as Li-intercalation electrode material

Net-structured NiO was prepared by urea-mediated homogeneous hydrolysis of Ni(CH₃COO)₂ under microwave radiation followed by a calcination at 500 °C. NiO–C nanocomposite was prepared by dispersing the as-prepared net-structured NiO in glucose solution and subsequent carbonization under hydrothermal conditions at 180 °C. The carbon in the composite was amorphous by the X-ray diffraction (XRD) analysis, and its content was 15.05 wt% calculated according to the energy dispersive X-ray spectroscopy (EDX) result. Transmission electron microscopy (TEM) image of the NiO–C nanocomposite showed that the NiO network was homogeneously filled by amorphous carbon. The reversible capacity of NiO–C nanocomposite after 40 cycles is 429 mAh g⁻¹, much higher than that of NiO (178 mAh g⁻¹). These improvements are attributed to the carbon, which can enhance the conductivity of NiO, suppress the aggregation of active particles, and increase their structure stability during cycling.     

Partially reduced SnO2 nanoparticles anchored on carbon nanofibers for high performance sodium-ion batteries

One-dimensional (1-D) carbon nanofibers anchored with partially reduced SnO₂ nanoparticles (SnO₂/Sn@C) were successfully synthesized through a simple electrospinning method followed by carbon coating and thermal reduction processes. The partially reduced Sn frameworks, combined with the carbon fibers, provide a more favorable mechanism for sodiation/desodiation than SnO₂. As a result, SnO₂/Sn@C exhibits a high reversible capacity (536 mAh g^− 1 after 50 cycles) and an excellent rate capability (396 mAh g^− 1 even at 2 C rate) when evaluated as an anode material for sodium-ion batteries (SIBs).     

Sulfone-based electrolytes for high-voltage Li-ion batteries

Sulfone-based electrolytes have been investigated as electrolytes for lithium-ion cells using high-voltage positive electrodes, such as LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ spinels, and Li₄Ti₅O₁₂ spinel as negative electrode. In the presence of imide salt (LiTFSI) and ethyl methyl sulfone or tetramethyl sulfone (TMS) electrolytes, the Li₄Ti₅O₁₂/LiMn₂O₄ cell exhibited a specific capacity of 80 mAh g^?1 with an excellent capacity retention after 100 cycles. In a cell with high-voltage LiNi_0.5Mn_1.5O₄ positive electrode and 1 M LiPF₆ in TMS as electrolyte, the capacity reached 110 mAh g^?1 at the C/12 rate. When TMS was blended with ethyl methyl carbonate, the Li₄Ti₅O₁₂/LiNi_0.5Mn_1.5O₄ cell delivered an initial capacity of 80 mAh g^?1 and cycled fairly well for 1000 cycles under 2C rate. The exceptional electrochemical stability of the sulfone electrolytes and their compatibility with the Li₄Ti₅O₁₂ safer and stable anode were the main reason behind the outstanding electrochemical performance observed with high-potential spinel cathode materials. These electrolytes could be promising alternative electrolytes for high-energy density battery applications such as plug-in hybrid and electric vehicles that require a long cycle life.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.