慢光在光子晶体弯折波导中的高透射传播

研究了慢光模式在SOI(silicon-on-insulator)材料光子晶体线缺陷弯折波导中的传输特性. 通过优化波导弯折处的结构参数,慢光模式在光子晶体60°与120°弯折波导中的透射率提高10倍以上,归一化透射率分别达到80%和60%以上. 为了进一步减慢光速,设计了新颖的高Q值耦合腔弯折波导结构,在归一化透射率达到75%的基础上,光波群速度低至c/170(c为真空光速). 研究结果对于增强光子晶体的慢光效应,提高光子晶体慢光器件的微型化和集成化都有一定的积 关键词： 光子晶体 慢光 弯折波导 透射率     

Properties of a 1 × 4 optical power splitter made of photonic crystal waveguides

Optical power splitters made of photonic crystal waveguides are believed to become essential components for compact photonic integrated circuits used in fiber optic networks. We design a 1 × 4 optical power splitter made of linear-defect waveguides in photonic crystals, and analyze its properties using the finite-difference time-domain method. Our simulation results show that the transmission properties vary with wave frequency and branch geometry, and that an incident wave is divided equally into four output ports. To reduce the reflections at the three branching regions in the 1 × 4 splitter, we place the defects of extra rods in the branching region, and achieve high transmission in each output waveguide.     

High-bandwidth and low-loss photonic crystal power-splitter with parallel output based on the integration of Y-junction and waveguide bends

A 1×2 power-splitter with parallel output that exhibits high-bandwidth and low-loss splitting for TE-polarized light is designed based on a photonic crystal slab in a silicon-on-insulator (SOI) material. The high performance is achieved by the integration of a Y-junction and 60° waveguide bends, which is designed to ensure single-mode operation, and keep the output channels of the power-splitter be parallel to the input channel. With a three-dimensional finite-difference time-domain (3D-FDTD) technique, ultralow-loss output of the optimized power-splitter with normalized transmission above 45% (in the range 3.216±0.18 dB) is obtained in the high-bandwidth range 1472–1634 nm, which covers the entire C-band of optical communication. In addition, the simulation results demonstrate that when the manufacture error of the lattice shift (dx) is in the range of ±10 nm, the disturbance of the transmission and the bandwidth are 1.52% and 6.79%, respectively. Both the specific result and the general idea of integration design are promising in the optical integrated circuit (OIC) and integrated optical devices in the future.     

1×4光子晶体波导分束器的特性

在完整的二维光子晶体中引入线缺陷,形成了光子晶体波导,光子晶体波导分束器是集成化光学电路的重要组成元件。我们设计了一种线缺陷1×4光子晶体分束器,并且用有限时域差分法研究了它的特性。研究表明,输出端的透射传输特性与入射光的波长和分支的几何形状有关,并且入射波分别相等地流入四个输出端口。为了减少1×4分束器在三个Y型分支区的反射,可以通过调节在分支区的可调介质柱的半径R,使每个输出端口具有很高的透射率。     

Photonic crystal bends and power splitters based on ring resonators

In this paper, theoretical and numerical analysis of low-loss right angle waveguide bends and T-junctions based on ultra-compact photonic crystal ring resonators (PCRR) is presented. Desirable characteristics are obtained by designing the waveguide bends and T-junctions as low-Q resonant cavities with certain symmetries and small radiation loss. A simple analysis, based on coupled mode theory (CMT) in time, is used to explain the operation principles which agree qualitatively with the numerical results. These structures have high transmission efficiency over a large bandwidth in third communication window. Also effects of changing the ring size on power splitter transmission characteristics are discussed. The perfect transmission and zero reflection conditions are discussed by applying coupled mode theory. Results obtained by the finite difference time domain (FDTD) simulations are consistent with those from the coupled mode theory.     

带有环形谐振器的1×2光子晶体功率分配器传输性能

 利用正方格2维光子晶体设计了带有环形谐振器的1×2光子晶体功率分配器结构,该结构具有1个输入端口和2个输出端口。采用时域有限差分法研究了该功率分配器对电磁波的传输性能,结果表明：其结构在第三通信窗口(1 550 nm波长)实现了电磁波的高效传输,同时具有优良的电磁波通频带功率二等均分性,以及电磁波传输转向设计灵活、损耗低、结构紧凑等优点。     

基于全内反射光子晶体多模波导偏振无关型光分束器

研究了全内反射在光子晶体多模波导中的作用,利用常规的耦合模理论对对称入射时的多模干涉行为和自映射现象进行了讨论和分析.研究表明,输入光场依然能沿着多模导光区高效的传输,这种结构中的光场传输是由全内反射和布喇格反射的联合作用而决定的.设计了一种全内反射偏振无关型光分束器,这种分束器在集成光学中具有重大的潜在应用价值.     

A compact T-branch beam splitter based on anomalous reflection in two-dimensional photonic crystals

We project a compact T-branch beam splitter with a micron scale using a two-dimensional (2D) photonic crystal (PC). For TE polarization, one light beam can be split into two sub-beams along opposite directions. The propagating directions of the two splitting beams remain unchanged when the incident angle varies in a certain range. Coupled-mode theory is used to analyze the truncating interface structure in order to investigate the energy loss of the splitter. Simulation results and theoretical analysis show that choosing an appropriate location of the truncating interface (PC-air interface) is very important for obtaining high efficiency due to the effect of defect modes. The most advantage of this kind of beam splitter is being fabricated and integrated easily.     

Archimedes 32,4,3,4结构光子晶体中与偏振无关的自准直分束器

通过等频图分析并结合时域有限差分法法模拟, 在Archimedes 3²,4,3,4结构排列的二维光子晶体中同一频率下同时实现了电磁波两种偏振态的自准直. 研究发现,在该结构光子晶体中引入缺陷,当线缺陷宽度改变时, TE和TM两种偏振态光束的分束效果将会随之变化.由此通过控制缺陷宽度,分别实现了两种偏振态光束的50% ∶50%分束以及90°大角度光折弯,分束和折弯的效率都较为理想,为未来设计基于光子晶体的新型光子学器件提供了一种新的思路.     

Detailed investigation of self-imaging in multimode photonic crystal waveguides for applications in power and polarization beam splitters

Properties of the self-imaging effect based on multimode interference (MMI) in multimode photonic crystal waveguides (PCWs) are investigated and analyzed in detail. By combining photonic band gap (PBG) and total internal reflection (TIR) effects in PCWs, self-imaging phenomena are achieved for both TE and TM polarizations. To observe the images reproduced by this self-imaging phenomenon, finite-difference time-domain (FDTD) simulations are performed on a multi-mode PCW. From these numerical simulations the reproduced images are identified and their positions along the propagation axis are described. We also, present the design and simulation of novel polarization-insensitive power splitter and polarization splitter. The simulation results show that the optimized devices have excellent transmission efficiencies as well as wide operating frequency bandwidths and small structure size. So, the proposed devices are promising and may play an important role in high-density photonic integrated circuits in the future.     

基于自准直效应的光子晶体异质结偏振分束器

基于光子晶体的自准直效应和禁带特性,提出了一种具有非正交异质结结构的光子晶体偏振分束器.无需引入缺陷或波导,可使光波在该结构中准直无发散地传输并实现分束功能,对制造工艺的要求大大降低.利用Rsoft软件,结合平面波展开法和二维时域有限差分法,对提出的偏振分束器进行了仿真研究.结果表明,该偏振分束器在一个较大的频率范围f=0.275—0.285(a/λ)内可实现横电(TE)和横磁(TM)模的大角度偏振分离,TE和TM模的透过率均在88%以上,偏振消光比分别大于26.57 dB和17.50 dB.该结构可应用到太赫兹波段的传输系统中,a=26μm,尺寸大小为572μm×546μm,在91—95μm波长范围内可实现TE和TM模的分离.利用该结构可设计用于光通信系统(n=3.48)的偏振分束器,a=426.25 nm,结构仅为9.38μm×8.95μm.本方案结构简单,易于集成,有望在集成光路的发展中发挥重要作用.     

基于1×4光子晶体波导分束器的特性研究

光子晶体波导分束器是集成光学电路的重要组成元件。设计一种线缺陷1×4光子晶体分束器,用时域有限差分法研究其特性。实验结果表明:输出端的透射传输特性随入射光的波长和分支的几何形状有关,并且入射波分别相等地流入4个输出端口。为了减少1×4分束器在3个Y型分支区的反射,通过调节分支区的可调介质柱的半径R,可使每个输出端口输出较高的透射率。     

Ultralow-loss 3-dB photonic crystal waveguide splitter

A photonic crystal waveguide splitter that exhibits ultralow-loss 3-dB splitting for TE-polarized light is fabricated in silicon-on-insulator material by use of deep UV lithography. The high performance is achieved by use of a Y junction, which is designed to ensure single-mode operation, and low-loss 60 degrees bends. Zero-loss 3-dB output is experimentally obtained in the range 1560-1585 nm. Results from three-dimensional finite-difference time-domain modeling with no adjustable parameters are found to be in excellent agreement with the experimental results.     

Design of a high efficiency wide-band 60° bend for TE polarization

In this paper, a high-efficiency 60° photonic crystal (PC) bend geometry is proposed. The corresponding PC is a two-dimensional triangular lattice of air holes in a dielectric slab. In the proposed bend structure, five additional holes are introduced in the bend. The radii of these holes are changed gradually. Hence the effect of bend discontinuity is decreased and consequently, a wide-band high efficiency bend is obtained. In this structure, the frequency bandwidth for which the transmission coefficient is greater than 0.9 covers 84% of the single-mode bandwidth of the waveguide, while for the best geometry reported in the literature this value does not exceed 56%. For numerical analysis of waveguide bends, the slab PC structure is first replaced by a two-dimensional (2D) PC with an effective refractive index and then, a 2D FDTD method is used to obtain the transmission coefficient of the bend.     

孔型硅光子晶体中折叠式马赫-曾德尔干涉仪

本文首次设计了基于孔型硅光子晶体的折叠式马赫-曾德尔干涉仪。它由一个光反射器和几个光分束器构成。在干涉仪中,窄光束依赖自准直效应进行传输。利用时域有限差分法研究了折叠式马赫-曾德尔干涉仪的特性。结果表明,在0.255-0.270c/a的归一化频率范围内,干涉仪的两个透射谱均为正弦形且强度互补,透射谱的透射峰间距随着干涉仪两臂的光程差的增大而减小。该折叠式干涉仪结构紧凑,尺寸比非折叠式光子晶体马赫-曾德尔干涉仪要小许多。它有望作为信道解复用器应用于光子芯片中。     

孔型硅光子晶体中折叠式马赫-曾德尔干涉仪(英文)

设计了基于孔型硅光子晶体的折叠式马赫-曾德尔干涉仪.它由一个光反射器和几个光分束器构成.在干涉仪中,窄光束依赖自准直效应进行传输.利用时域有限差分法研究了折叠式马赫-曾德尔干涉仪的特性.结果表明,在0.255～0.270c/a的归一化频率范围内,干涉仪的两个透射谱均为正弦形且强度互补,透射谱的透射峰间距随着干涉仪两臂的光程差的增大而减小.该折叠式干涉仪结构紧凑,尺寸比非折叠式光子晶体马赫-曾德尔干涉仪要小许多,有望作为信道解复用器应用于光子芯片中.     

基于波导间能量耦合效应的光子晶体频段选择与能量分束器

基于波导间能量耦合效应的光子晶体功率分束器具有结构紧凑、带宽较宽、弯曲损耗低、分光角度大和不受外界电磁场干扰等优点.本文利用时域有限差分方法,理论研究了二维三角晶格光子晶体耦合波导的功率分束特性,设计得出了一种能够在宽频谱范围内针对不同频率区间实现不同分光比的功能器件.在此基础上通过改变耦合区介质柱形状以及输出分支波导与能量耦合波导的连接位置,最终针对三个相邻频率范围内的入射光信号,较好地实现了三均分、二均分、单一输出通道这3种能量分配输出模式.该功能器件具有透过率对比度高、结构紧凑等特性,对于发展全光功能器件在大规模全光复杂集成领域内的实际应用具有一定的促进作用.     

一种新型的光子晶体偏振光分束器的设计

基于光波在直波导和复合结构光子晶体中的传播特性,结合平面波展开法和时域有限差分法,提出并讨论了一种新型的超紧凑的光子晶体偏振光分束器. 它是由输入波导,分束结构和输出波导三部分组成. 对这种结构的三角晶格光子晶体光分束器的数值计算与模拟结果表明,该结构可以实现TE模和TM模的高效大角度分离,并且在通信波段设计尺寸小,这些特性使其在未来的集成光回路中有着重要的应用前景. 关键词： 偏振光分束器 能带结构 平面波展开法 时域有限差分法     

跑道型结构光子晶体波导定向耦合器

鉴于波导定向耦合器在集成光路以及光电集成方面的广泛应用,提出了一种基于光子晶体波导间高效耦合的光子晶体定向耦合器。通过主波导和耦合波导间的耦合,可以实现对波长为1 490 nm和1 550 nm电磁波的高效分光。在将器件长度控制在30 μm左右的同时,其总效率高达93.05%。另外,发现主波导和耦合波导间介质柱结构参数对电磁波的耦合周期有着极大的影响。并通过将介质柱沿z方向拉伸0.1a(a为晶格周期),设计了工作波长为1 530 nm和1 540 nm的光子晶体定向耦合器,器件长度仅为60 μm。通过拉伸介质柱的纵向长度,可以大幅减小耦合周期,这对缩小器件体积以及实现更为密集的波分复用有着重要的意义。     

Novel composite beam splitter with directional coupler and Y-junction using photonic crystal

We propose and analyze a novel multiway high efficiency composite beam splitter based on propagation properties of the light waves in directional coupler and Y-junction. The splitting properties of the beam splitter have been numerically simulated and analyzed using the PWE and FDTD methods. Then in order to obtain equal distribution of power, we place and adjust some additional rods in the output waveguides to optimize the devices. It was shown that a large separating angle, a high beam rate, high flexibility, has been extended to have more light output channels in the beam splitter.