342W全光纤结构窄线宽连续掺铥光纤激光器

报道了一个全光纤主振荡功率放大结构的窄线宽连续掺铥光纤激光器,该激光器由窄线宽连续掺铥光纤激光种子源和两级包层抽运掺铥光纤放大器组成.自制的窄线宽掺铥光纤激光种子源经过两级高功率包层抽运掺铥光纤放大器之后,最高平均输出功率为342 W,掺铥光纤功率放大器的斜率效率为56%,输出激光的中心波长为2000.3 nm,3 d B光谱带宽仅为90 pm.在放大过程中,功率放大器的反向监测端没有观察到受激布里渊散射效应,输出功率仅受限于当前可用的793 nm半导体抽运源的功率.据我们所知,该结果为目前国际上2μm波段全光纤结构窄线宽激光器所产生的最高输出功率.     

780W全光纤窄线宽光纤激光器

高功率窄线宽光纤激光器在相干探测、功率光谱合成等方面具有广泛的应用前景.分析了高功率窄线宽光纤激光器中受激布里渊散射效应的抑制方法,以及正弦相位调制光谱展宽理论.采用正弦相位调制技术将单频激光器的线宽展宽至2.9 GHz,通过三级放大结构对输出功率为50 mW的窄线宽种子源进行放大,实现了中心波长1064.34 nm、线宽2.9 GHz、最大功率780 W的激光输出,光—光转换效率79%,光束质量M2x=1.44,M2y=1.43.分析了相位调制前后输出功率提高的原因,认为正弦相位调制增加的纵模降低了光纤中的功率谱密度,提高了输出激光的受激布里渊散射阈值,促使相位调制后的输出功率大幅提高.该激光器的输出功率仅受限于抽运功率,进一步提高抽运功率,有望实现更高功率的窄线宽光纤激光输出.     

基于MOPA结构的1120nm掺Yb光纤放大器

基于主振荡功率放大器,采用1120nm光纤激光器作为种子激光,将其注入20m大模场面积单模双包层掺Yb光纤放大器,并用976nm半导体激光器泵浦实现了1 120nm信号光输出.实验中将注入种子激光功率预设为10mW,当半导体激光器泵浦功率增大至1.5 W时,放大器系统开始输出1 120nm信号光.当泵浦功率低于3.4W时,信号光功率随泵浦功率缓慢增长,系统斜率效率较低;而当泵浦功率高于3.4W时,信号光功率随泵浦功率线性增长,斜率效率明显增大,达到48.5%.限于最大注入泵浦功率为6.8W,放大器输出最高1 120nm信号光功率为1.97W,总的光-光转化效率为29%.输出信号光中心波长为1 120.89nm,线宽为0.02nm,极好地保持了种子激光的特性.结合实验情况,利用双包层光纤放大器的稳态理论模型,采用有限差分方法模拟了放大器输出信号光功率随泵浦光功率的变化曲线,结果显示理论模拟所得变化趋势与实验结果吻合良好,系统将在泵浦功率达到200W左右时达到饱和状态,说明目前光纤放大器系统具有很大的功率提升空间.     

窄线宽1064 nm光纤激光泵浦高效率中红外3.8μm MgO:PPLN光参量振荡器

采用放大1064 nm掺镱光纤激光器作为泵浦源,实现了中红外3.8μm MgO:PPLN光参量振荡(OPO)激光输出。在泵浦源中,采用分布式反馈激光器(DFB)作为种子源来实现光纤激光窄线宽的调制,实现线宽2.5 nm到0.1 nm的压缩,最大平均输出功率可达40 W。进一步对不同泵浦线宽条件下中红外3.8μm MgO:PPLN OPO激光进行研究,最终在泵浦功率为18.1 W、线宽为0.1 nm、重频为1 MHz、脉宽为2 ns时,获得了最高平均输出功率为2.06 W的3822.5 nm激光输出,光-光转换效率为11.38%,光束质量为M2=2.34,提高了窄线宽泵浦对中红外MgO:PPLN OPO激光输出效率。     

宽带可调谐单频窄线宽光纤激光器

设计出一种集可调谐带通滤波器、高精度环形滤波器和光纤环形镜于一体的全光纤复合腔结构可调谐单频窄线宽光纤激光器。采用980 nm半导体激光器作为抽运源,掺镱光纤在谐振腔内分别作为增益介质和可饱和吸收体,成功实现波长为1030～1090 nm稳定的宽谱可调谐单频窄线宽激光输出。当抽运光的抽运功率为300 mW时,在波长为1070 nm处得到的输出功率最大,为18.5 mW,斜率效率达到7.95%,持续1 h内没有出现跳模现象,功率不稳定性小于1%;当抽运功率为200 mW时,利用延迟自外差法测量线宽,得到波长调谐范围内的平均线宽为8.7 kHz,弛豫振荡频率为64 kHz。     

双纵模窄线宽光纤拉曼放大器

 报道了一台实现了双纵模窄线宽激光输出的光纤拉曼放大器。利用中心波长1 079.7 nm的双纵模窄线宽种子激光器获得了频率间隔1.4 GHz、功率比约3∶1的双纵模输出,各纵模的线宽约为10 MHz;再利用1 031 nm泵浦光对双纵模种子光进行拉曼放大,实现了1.07 W双纵模激光输出。拉曼放大过程中,两个纵模的线宽、频率间隔及功率比保持得很好。     

激光线宽对单次通过PPMgO:LN晶体倍频效率的影响

通过单次穿过PPMgO:LN晶体产生了2.06 W的780 nm可调谐的连续倍频光. 采用1560 nm的分布反馈式(DFB)半导体激光器、光栅外腔半导体激光器(ECDL)和分布反馈式掺铒光纤激光器(DFB-EDFL)分别作为掺铒光纤放大器(EDFA)的注入光源, 所用的EDFA具有保持窄线宽的功能, 因此可以忽略它对基波线宽的展宽. 研究了激光线宽对单次通过PPMgO:LN 晶体的倍频效率的影响. 控制三台激光器各自注入EDFA的功率一致, 同时也保持EDFA 的输出功率. 在基波功率为12.42 W 时, 使用DFB半导体激光器注入EDFA时得到了1.36 W的780 nm倍频光输出, 转换效率为11.0%; 使用ECDL作为种子源时得到了1.78 W 的780 nm倍频光输出, 转换效率为14.3%; 使用DFB-EDFL作为种子源时得到了2.06 W的780 nm倍频光输出, 转换效率为16.6%. 测得三台种子激光器的线宽分别为1.2 MHz (DFB), 200 kHz (ECDL)和600 Hz (DFB-EDFL). 线宽越窄, 倍频效率越高, 实验结果与理论分析一致.     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

国产全光纤结构激光器实现245 W高功率激光输出

 以国产掺镱光纤为增益介质,利用国产泵浦源和光纤器件,构建了主振荡功率放大（MOPA）结构的全国产大功率全光纤激光器。激光器包括10 W种子激光器和高功率放大器两部分。在注入最大泵浦功率为356 W时,获得了245 W波长1 080 nm激光的稳定输出,光-光效率为69%。激光器单次连续出光时间约30 min,功率稳定性在1%以内。目前激光器输出功率受限于泵浦功率,增加泵浦源的数目有望进一步提高输出功率。     

主振荡功率放大结构窄线宽全光纤激光器334 W高功率输出

 搭建了一台全光纤结构的窄线宽高功率掺镱光纤激光器。种子激光的输出功率大于40 mW,线宽窄于100 MHz。采用主振荡功率放大结构三级放大,主放泵浦功率为405 W时得到了334 W的窄线宽高功率激光输出,光光转换效率为82.4%。目前,激光器输出功率仅受限于泵浦功率,增加有效泵浦功率即有望进一步提高输出功率。     

29.2 W, 20 kHz linewidth all fiber single-frequency MOPA laser

We demonstrate a high power all fiber single-frequency MOPA laser. The center wavelength of the single-frequency fiber laser seed is 1064 nm with a linewidth narrower than 20 kHz. A two-stage power amplification configuration is employed. A single-frequency fiber laser with an output power of 29.2 W is obtained, and the optical to optical efficiency is 78%.     

脉冲单频Nd:YVO4激光器及其倍频输出特性研究

为了研制激光干涉成像所需的主振荡功率放大(MOPA)结构脉冲单频激光器,本文完成MOPA激光器的种子源即声光调Q脉冲单频1 064 nm激光器的特性研究,同时完成种子源腔外倍频绿光特性研究。脉冲单频激光器采用声光调Q模块实现脉宽约20 ns的1 064 nm脉冲激光输出,采用环形腔设计并采用一组不同厚度的标准具实现单纵模运转。实验研究基频1 064nm和倍频532 nm激光脉冲的线宽,得出在全脉宽范围内都具有较高时间相干性的结论。实验分别获得脉宽约28 ns峰值功率约6.5 kW的1 064 nm脉冲单频激光和脉宽约20 ns、峰值功率约0.5 kW的532 nm脉冲单频激光,腔外倍频效率为5.6%。实验同时也验证了腔外倍频的激光脉宽压缩效应。     

122-W high-power single-frequency MOPA fiber laser in all-fiber format

We demonstrate a high-power single-frequency master oscillator power amplifier (MOPA) fiber laser.The central wavelength of the single-frequency fiber laser seed is 1 063.8 nm,with a linewidth narrower than 20 kHz and output power of 120 mW.By using two-stage amplification,a single-frequency fiber laser with an output power of 122 W is obtained,and the optical-optical conversion efficiency is 72%.No significant amplified spontaneous emission (ASE) or stimulated Brillouin scattering (SBS) is observed.The output power can be further increased by launching more pump power.     

百瓦级全光纤结构单频掺铥主振荡功率放大器

报道了平均功率超过百瓦的单频掺铥全光纤结构主振荡功率放大器。使用线宽小于100kHz、中心波长为1.97μm的单频种子源进行级联放大,主放大器的斜率效率为50%。监测放大器的回光功率和光谱,没有发现受激布里渊散射以及其他非线性效应。通过增加泵浦功率,可以获得更高功率的掺铥单频放大输出。     

An Efficient Single-Frequency Yb-Doped All-Fiber MOPA Laser at 1064.3 nm

An efficient narrow-linewidth single-frequency(SF) Yb-doped all-fiber master oscillator power amplifier(MOPA)laser operating at 1064.3 nm is demonstrated experimentally.A ring cavity SF fiber laser is used as the seed source for the MOPA system and the Yb-doped fibers are employed as the gain medium or the saturable absorber.The SF operation is observed to be stable without mode hopping.The highest output power of 266 mW is obtained under the 400 mW pump power with the corresponding slope efficiency of 66.2%.The linewidth of the amplified output laser is approximately 1 kHz and its optical signal-to-noise ratio is over 45 dB.     

90.4-W all-fiber single-frequency polarization-maintained 1083-nm MOPA laser employing ring-cavity single-frequency seed oscillator

A high-power all-fiber single-frequency polarization-maintained（PM）laser operating at 1 083 nm is demonstrated using a master oscillator power amplifier（MOPA）structure.The seed source of this MOPA laser system is an in-house-built ring-cavity fiber oscillator.Four-stage amplification configuration is employed, in which the maximal output power of the main amplifier is 90.4 W,corresponding to a conversion efficiency of 72.5%.The polarization extinction ratio of the output light is 13 dB.The amplified spontaneous emission is suppressed by a factor of over 25 dB,and no stimulated Brillouin scattering effect is observed when a large-mode-area and high absorption coefficient PM gain fiber is employed.     

96.2 W all-fiberized nanosecond single-frequency fiber MOPA

We report experimental results on a 96.2 W all-fiberized nanosecond single-frequency masteroscillator power amplifier (MOPA) laser working at 1064 nm. An external modulation fiber laser with average power of 0.5 mW and line width of 20 kHz is used as the seed source. Amplifying the seed laser in four stages, a single-frequency laser with pulse duration of 10 ns and peak power of 816.7 W is obtained. The average output power is up to 96.2 W. Further power-scaling of this MOPA structure can be realized since our experiment is only pump-power limited.     

Injection-Seeded 500 Hz Repetition Rate High Peak Power Single-Frequency Nd:YAG Laser for Mid-Infrared Generation

We develop an injection-seeded single-frequency neodymium-doped yttrium aluminum garnet (Nd:YAG) laser with 500 Hz repetition rate and high peak power. The laser construction is designed as seed injection and master oscillator power amplifier (MOPA) including single-frequency master oscillator, extra-cavity frequency doubling crystal, and round-trip power amplifier. The master oscillator can emit 1,064 nm laser of 8.4 mJ with 6.8 ns pulse width at the pump energy equal to 23 mJ. A green laser energy of 1.1 mJ is obtained by setting the proper temperature of the LBO crystal. The pulse energy of 1,064 nm laser decreases to 6.5 mJ after passing through the LBO crystal and rises to 25.3 mJ after a round-trip power amplifier corresponding to the extraction efficiency of 29%. The final output pulse width is 6.5 ns, representing a peak power of 3.9 MW. The 1,064 nm laser beam quality factor M² of the master oscillator and the amplified one are 1.3 and 1.5, respectively. The laser will be used to generate mid-infrared where the 532 nm laser with narrow pulse width is to pump sheet optical parametric oscillator (OPO) and the 1,064 nm laser with high peak power to pump the OPO.     

Optimization of erbium-doped fiber MOPA laser

An erbium-doped fiber laser (EDFL) constructed in a master oscillator and power amplifier (MOPA) configuration is analyzed. The pump powers for the fiber cavity laser and the booster amplifier stages are managed properly to achieve maximal pump conversion efficiency. Our design achieves a pump conversion efficiency of 91.4%, corresponding to a quantum efficiency of 96.6%, for a 1565.8 nm MOPA laser pumped by a total power of 300 mW at 1480 nm. The optimized MOPA laser shows a 25% enhancement in the pump conversion efficiency, compared to a non-MOPA fiber laser. A side lobe suppression ratio of 48 dB for the optimized MOPA laser is observed.     

Power scaling of resonantly cladding-pumped, Yb-free, Er-doped LMA fiber lasers

The results of the recent major efforts in power scaling of resonantly cladding-pumped Yb-free Er fiber lasers are presented. Commercially available Yb-free Er-doped large mode area Er60-20/125 (LMA) DC fibers were tested in two regimes: (i), as a booster amplifier in a single-frequency (SF) MOPA configuration and, (ii), in a Bragg grating (FBG) based narrowband fiber laser configuration. We obtained ～28.5 W of output power at 1590 nm, the highest power reported so far out of Yb-free Er-doped LMA fiber with resonant cladding pumping. The achieved optical-to-optical conversion slope efficiency of ～56.6% is also believed to be the highest efficiency ever reported from Yb-free Er-doped fiber laser with resonant cladding pumping.