P(VAc-MMA)为基体的聚合物电解质研究

以醋酸乙烯酯(VAc)和甲基丙烯酸甲酯(MMA)为单体, 采用半连续种子乳液聚合法制备了无规共聚物聚(醋酸乙烯酯-甲基丙烯酸甲酯)[P(VAc-MMA)], 并以此聚合物为基体制备了聚合物电解质. 用红外光谱(FTIR)、核磁共振氢谱(¹H NMR)、扫描电镜(SEM)、差热/热重分析(DSC/TG)、X射线衍射(XRD)、机械性能测试和电化学交流阻抗等方法对聚合物和聚合物电解质的性质进行了研究. 测试结果表明: VAc和MMA聚合生成P(VAc-MMA); 聚合物膜含有大量微孔结构, 利于离子传输; 聚合物电解质膜具有优良的热稳定性和机械强度; 25 ℃下, 最高的离子电导率达到了1.27× 10^－3 S•cm^－1; 离子电导率随着温度的升高而迅速增加, 电导率-温度曲线符合Arrhenius方程.     

PAMPSLi/P(MMA-VAc)为基体的聚合物电解质

将聚(2-丙烯酰胺-2-甲基丙磺酸锂)(PAMPSLi)和聚(甲基丙烯酸甲酯-醋酸乙烯酯)[P(MMA-VAc)]与LiClO₄共混, 制备了复合聚合物电解质膜. 用FTIR, TG, XRD, DMA, SEM及电化学交流阻抗和机械性能测试对聚合物及其电解质膜的结构和性能进行了表征. 结果表明, PAMPSLi与P(MMA-VAc)共混后结晶状态发生变化, 交联网络变得密实, 提高了热稳定性和拉伸强度, 聚合物电解质膜含有较多微孔结构, 孔径为5~10 μm; 在20 ℃时, 当n(MMA)∶n(VAc)=2∶8, m(PAMPSLi)∶m[P(MMA-VAc)]=5∶95, m(LiClO₄)∶m(copolymer)=15∶85时, 聚合物电解质膜电导率可达到1.68×10^-3 S/cm, 且电导率未出现随LiClO₄含量的进一步增加而下降的现象. 将此电解质用于全固态电致变色显示器件表现出了优良的性能. 对加入PAMPSLi后聚合物电解质膜电导率和热稳定性提高的原因进行了初步探讨.     

原位聚合制备的离子液体/聚合物电解质的研究

采用原位聚合制备出新型的BMIPF6/PMMA聚合物电解质透明弹性膜. 研究结果表明, BMIPF6/PMMA聚合物电解质体系在305 ℃时仍具有较好的热稳定性, 其安全性能优于含有机溶剂的传统非水电解质体系. 随着离子液体含量的增加, 其玻璃化转变温度逐渐减小, 离子电导率升高; 且离子电导率与温度的关系服从VTF方程. 其中, 当BMIPF6的质量分数为50%时, 该聚合物电解质的室温离子电导率高达0.15 mS/cm.     

POSS星型聚合物对PMMA复合凝胶聚合物电解质性能的影响

为了提高凝胶聚合物电解质(GPE)的离子传输性,以低聚倍半硅氧烷(POSS)为核,臂结构为聚甲基丙烯酸甲酯(PMMA),臂聚合度不同的八臂星型聚合物(POSS-(PMMA3)8、POSS-(PMMA6)8、POSS-(PMMA9)8)为改性剂,分别与PMMA共混制备复合GPE,研究了POSS星型聚合物臂结构对复合GPE电性能影响的规律.结果表明,POSS星型聚合物的引入,使得复合GPE的电导率较纯PMMA基GPE均有显著提高,其中臂聚合度较小的POSS-(PMMA3)8复合GPE在室温的电导率最大,比纯PMMA基GPE提高了3.5倍.分析了该星型聚合物不同含量以及锂盐浓度等对复合凝胶聚合物电解质的影响,发现锂盐浓度在凝胶体系中为0.6 mol/L,该星型聚合物含量为聚合物基体15 wt%时,复合凝胶聚合物电解质电导率最大为2.73×10-4S/cm.研究了温度对复合凝胶聚合物电解质离子传输性能的影响规律,发现其离子传输规律符合Arrhenius方程.在此基础上,提出了该凝胶电解质体系的离子传输微观结构模型.     

锂离子电池PMMA-VAc聚合物电解质的制备与性质研究

以甲基丙烯酸甲酯(MMA)和醋酸乙烯酯(VAc)为单体, 用乳液聚合法合成聚甲基丙烯酸甲酯-醋酸乙烯酯聚合物(PMMA-VAc), 并以此聚合物制备了新型聚烯烃膜支撑的聚合物膜及聚合物电解质. 用红外光谱(FTIR)、凝胶色谱(GPC)、差热和热重分析(DSC/TG)、扫描电镜(SEM)及电池充放电实验等方法研究了聚合物、聚合物膜和聚合物电解质的性质. 红外光谱结果表明, MMA与VAc通过各自的C＝C双键打开聚合成PMMA-VAc. PMMA-VAc易于分散在混合碳酸酯溶剂中并形成凝胶, 凝胶粘度随PMMA-VAc浓度的增加而增加, 当浓度为4%时成膜效果最佳. PMMA-VAc膜具有大量的微孔结构, 具有极强的吸液性能. PMMA-VAc膜具有良好的热稳定性: 在380 ℃范围内保持稳定. 聚烯烃膜支撑的PMMA-VAc膜室温下的离子电导率为1.85×10^－3 S•cm^－1, 用作为锂离子电池的聚合物电解质时, 电池具有良好的循环稳定性和倍率性能.     

用于锂离子电池的凝胶聚合物电解质的制备与性能

以丙烯腈(AN)、丙烯酸甲酯(MA)和衣康酸锂(IALi)为自由基共聚反应的主要单体, 采用溶液聚合方法, 合成轻度交联的P(AN-MA-IALi)聚合物电解质膜.通过FTIR, DSC和SEM等测试方法对共聚物的结构进行了表征, 利用交流阻抗等电化学方法对该膜的导电性能进行了研究.实验结果表明, 所制备的交联聚合物的室温电导率达到10-5~10-4 S/cm, 当IALi的质量分数为3%时, 所制备的聚合物电解质膜的电导率最大可达到1.89×10-4 S/cm.     

红外光谱研究PEO基离子液体聚合物电解质

以聚氧化乙烯(PEO)为聚合物基体, 双三氟甲基磺酸亚酰胺锂(LiTFSI)为锂盐, 加入不同量的离子液体(BMIMPF₆)为增塑剂, 制备离子液体聚合物电解质. 运用发射FTIR光谱技术实时监测所制备聚合物电解质的结构随温度的变化. 结合FTIR透射光谱\, SEM和XRD的研究结果分析了离子液体对离子电导率的影响, 并初步提出离子导电增强机制.     

新型PMMA基聚合物电解质的研制

制备了聚甲基丙烯酸甲酯（PMMA）基聚合物电解质，通过加入交联剂使其形成网状结构，提高了聚合物电解质的机械性能.对MMA以及交联剂的含量作了优化，并测试了聚合物电解质的温度特性.测试结果表明,MMA、EGD(二甲基丙烯酸乙二醇酯)和电解液(LiBF4/EC DMC)含量分别为25％、2％、73％(质量分数）时，所制备的聚合物电解质具有较高的电导率，室温条件下可以达到2×10－3 S•cm－1，电化学窗口为4.8 V.用其作为电解质组装的聚合物锂离子电池具有较好的充放电性能.     

一种高离子电导率复合聚合物电解质的简易热处理制备

固态聚合物电解质是发展柔性全固态锂离子电池的核心,但是目前室温离子电导率低限制了其应用.本研究以热聚合方法制备石墨相氮化碳(g-C_3N_4),并将其与聚氧化乙烯/高氯酸锂(PEO/LiClO_4)共混制备复合聚合物固态电解质.采用X射线衍射(XRD)、傅里叶变换红外光谱(FTIR)、光学显微镜(OM)、扫描电子显微镜(SEM)、差示扫描量热仪(DSC)和电化学工作站对复合聚合物电解质膜进行表征.结果表明,通过120℃退火-淬冷热处理及复合聚合物电解质内部的相互作用,可以较大程度抑制PEO的结晶,从而使该复合聚合物固态电解质膜的离子电导率在25℃时达到2.4×10~(-5)S cm~(-1),提高了3个数量级.     

以水作相分离造孔剂制备P(VDF-HFP)/PMMA聚合物电解质膜

介绍了一种以水代替常用的有机物质作为相分离造孔剂制备混合型聚合物电解质的新方法.所研究的混合型聚合物为聚(偏二氟乙烯-六氟丙烯)和聚甲基丙烯酸甲酯的混合物.扫描电镜SEM图表明这种混合型聚合物膜具有蜂窝状结构,有利于膜电导率的增加.利用FTIR,XRD和DSC等方法研究了混合型聚合物电解质中两种聚合物间的相互作用.用电化学交流阻抗方法测得在30℃下P(VDF-HFP)/PMMA摩尔比为1:1的混合型聚合物电解质的离子电导率为0.804×10^-3S/cm.对照其它方法,本方法具有制备容易、成本较低和有利于环境保护等优点.     

STUDY ON THE PREPARATION AND PERFORMANCES OF P(VAc-MMA) POLYMER ELECTROLYTES FOR LITHIUM ION BATTERY

A random copolymer P(VAc-MMA)was synthesized via seeded emulsion copolymerization with vinyl acetate (VAc)and methyl methacrylate(MMA)as monomers,and the polymer electrolytes comprising blend of corresponding copolymer P(VAc-MMA)as a host polymer and LiClO_4 as a dopant were prepared by solution casting technique. Performances of the synthesized copolymer and prepared polymer membrane and electrolyte were studied by FTIR,XRD, TG,DSC,mechanical testing and AC impedance.According to the study of FTIR and D...     

Cross-linking copolymers of acrylates’ gel electrolytes with high conductivity for lithium-ion batteries

The cross-linking gel copolymer electrolytes containing alkyl acrylates, triethylene glycol dimethacrylate, and liquid electrolyte were prepared by in situ thermal polymerization. The gel polymer electrolytes containing 15 wt% polymer content and 85 wt% liquid electrolyte content with sufficient mechanical strength showed the high ionic conductivity around 5?×?10^?3 Scm^?1 at room temperature. The gel electrolytes containing different polymer matrices were prepared, and their physical observation and conductivity were discussed carefully. The cross-linking copolymer gel electrolytes of alkyl acrylates with other monomers were designed and synthesized. The results showed that copolymerization can improve the mechanical properties and ionic conductivities of the gel electrolytes. The polymer matrices of gels had excellent thermal stability and electrochemical stability. The scanning electron microscope analysis showed the gel electrolyte was the homogeneous structure, and the cross-linking polymer host was the porous three-dimensional network structure, which demonstrated the high conductivity of the gel electrolytes. The gel polymer Li-ion battery was prepared by this in situ thermal polymerization. The cell exhibited high charge-discharge efficiency at 0.1 C. The results of LiFePO4-PEA-Li cell and graphite-PEA-Li cell showed that gel polymer electrolytes have good compatibility with the battery electrodes materials.     

MMA/MAh共聚物的合成及其凝胶聚合物电解质性能

从聚甲基丙烯酸甲酯型凝胶聚合物电解质存在的问题出发,设计制备一种甲基丙烯酸甲酯/共聚马来酸酐型凝胶聚合物电解质.采用溶液聚合法,以偶氮二异丁腈(AIBN)为引发剂,甲基丙烯酸甲酯(MMA)、顺丁烯二酸酐(MAh)为单体,其MMA与MAh单体摩尔配比为1∶1,合成了P(MMA-co-MAh)共聚物;采用凝胶色谱(GPC)、傅立叶红外光谱(FTIR)、核磁共振(MNR)、示差扫描量热法(DSC)、热失重分析(TGA)、X-射线衍射分析(XRD)对所合成共聚物的结构进行了表征.结果表明,合成的共聚物为无规非晶型聚合物,其数均分子量Mn为6.40×104,共聚物中MMA与MAh链段摩尔比大约为8∶1,热分解温度为300℃,玻璃化转变温度(Tg)为121.3℃.以P(MMA-co-MAh)共聚物为树脂基体,环状碳酸1,2-丙二酯(PC)为增塑剂,LiClO4为电解质盐,制备了凝胶聚合物电解质(GPE),当共聚物含量为45 wt%时,GPE具有好的成膜性,其室温离子电导率为3.0×10-5S/cm.     

PREPARATION OF STAR NETWORK PEG-BASED GEL POLYMER ELECTROLYTES FOR ELECTROCHROMIC DEVICES

An amorphous,colorless,and highly transparent star network polymer with a pentaerythritol core linking four PEG-block polymeric arms was synthesized from the poly(ethylene glycol)(PEG),pentaerythritol,and dichloromethane by Williamson reaction.FTIR and ~1H-NMR measurement demonstrated that the polymer repeating units were C[CH_2-OCH_2O-(CH_2CH_2O)_m-CH_2O-(CH_2CH_2O)_n-CH_2O]_4.The polymer host held well mechanical properties for pentaerythritol cross-linking.The gel polymer electrolytes based on Lithium...     

Preparation of a Star Network PEG-based Gel Polymer Electrolyte and Its Application to Electrochromic Devices

A star network polymer with a pentaerythritol core linking four PEG-block polymeric arms was synthesized, and its corresponding gel polymer electrolyte based on lithium perchlorate and plasticizers EC/PC with the character being colorless and highly transparent has been also prepared. The polymer host was characterized and confirmed to be of a star network and an amorphous structure by FTIR, ^1H NMR and XRD studies. The polymer host hold good mechanical properties for pentaerythritol cross-linking. Maximum ionic conductivity of the prepared polymer electrolyte has reached 8.83 × 10 ^-4 S·cm^-1 at room temperature. Thermogravimetry （TG） of the polymer electrolyte showed that the thermal stability was up to at least 150 ℃. The gel polymer electrolyte was further evaluated in electrochromic devices fabricated by transparent PET-ITO and electrochromically active viologen derivative films, and its excellent performance promised the usage of the gel polymer electrolyte as ionic conductor material in electrochrornic devices.     

PEO/LiClO_4纳米SiO_2复合聚合物电解质的电化学研究

将实验室制备的纳米二氧化硅和市售纳米二氧化硅粉末与PEO LiClO4复合 ,制得了复合PEO电解质 .它们的室温离子电导率可比未复合的PEO电解质提高 1～ 2个数量级 ,最高可以达到 1 2 4× 10 - 5S cm .离子电导率的提高有两方面的原因 :一是无机二氧化硅粉末的加入抑制了PEO的结晶 ,是二氧化硅粉末和聚合物电解质之间形成的界面对电导率的提高也有一定的作用 .在进一步加入PC EC(碳酸丙烯酯 碳酸乙烯酯 )混合增塑剂后制得的复合凝胶PEO电解质 ,可使室温离子电导率再提高 2个数量 ,达到 2× 10 - 3 S cm .用这种复合凝胶PEO电解质组装了Li|compositegelelectrolyte|Li半电池 ,并测量了该半电池的交流阻抗谱图随组装后保持时间的变化 ,实验观察到在保持时间为 144h以内钝化膜的交流阻抗迅速增大 ,但在随后的时间内逐渐趋于平稳 ,表明二氧化硅粉末的加入可以有效地抑制钝化膜的生长     

基于聚乙二醇接枝丙烯酸树酯光固化电解质的制备及性能研究

聚氧化乙烯(PEO)(聚乙二醇(PEG))和丙烯酸树脂在聚合物基电解质中具有很好的应用,本文通过紫外光引发单/双官能度的聚乙二醇接枝丙烯酸树脂单体聚合构建了离子电导率高、易于封装,可避免电解质泄漏的准固态聚合物电解质.通过调控聚乙二醇二甲基丙烯酸酯(PEGDA)和甲氧基聚乙二醇单甲基丙烯酸酯(PEGMA)2种单体的比例以及锂盐溶液的含量,成功制备出具有高离电导率的准固态聚合物电解质.采用傅里叶变换红外光谱仪(FTIR),电化学工作站对PEGMA/PEGDA基聚合物电解质进行表征,研究各组分比例对电解质的电化学性能影响.当PEGMA/PEGDA单体比例为75/25,锂盐溶液的占比为75%时,形成的薄膜状态电解质表现出1.96×10^?3 S·cm^?1的高离子电导率,较原始配比提高了14倍.将制备的电解质应用于电致变色器件,在580个变色循环后,器件依然可以实现稳定快速的颜色切换,2种颜色变换时间均在3 s以内,本文中研究的聚醚接枝丙烯酸树酯基电解质材料在电致变色器件中有较好的应用前景.     

染料敏化太阳电池用聚合物电解质

综述了本研究小组近年来用于染料敏化太阳电池中聚合物电解质的研究概况.设计合成了几类性能优良的聚合物电解质,较好地改进了液体电解质染料敏化太阳电池(DSSC)的使用稳定性,研究结果具有实际应用的价值,并提出了此领域研究今后的发展方向.     

Improving the performance of all-solid-state supercapacitors by modifying ionic liquid gel electrolytes with graphene nanosheets prepared by arc-discharge

Ionic liquid gel polymers have widely been used as the electrolytes in all-solid-state supercapacitors, but they suffer from low ionic conductivity and poor electrochemical performance. Arc discharge is a fast, low-cost and scalable method to prepare multi-layered graphene nanosheets, and as-made graphene nanosheets （denoted as ad-GNSs） with few defects, high electrical conductivity and high thermal stability should be favorable conductive additive materials. Here, a novel ionic liquid gel polymer electrolyte based on an ionic liquid （EM1MNTF2） and an copolymer （P（VDF-HFP）） was modified by the addition of ad-GNSs as an ionic conducting promoter. This modified gel electrolyte shows excellent thermal stability up to 400 ℃ and a wide electrochemical window of 3 V. An all-solid-state supercapacitor based on commercial activated carbon was fabricated using this modified ionic liquid gel polymer electrolyte, which shows obviously improved electrochemical behaviors compared with those of the corresponding all-solid-state supercapacitor using pure ionic liquid gel polymer electrolyte. Specially, smaller internal resistance, higher specific capacitance, better rate performance and cycling stability are achieved. These results indicate that the ionic liquid gel polymers modified by ad-GNSs would be promising and suitable gel electrolytes for high performance all-solid-state electrochemical devices.