Nonionic surfactants: a key to enhance the enzyme activity at cationic reverse micellar interface

The primary objective of the present study is to understand how the different nonionic surfactants modify the anisotropic interface of cationic water-in-oil (W/O) microemulsions and thus influences the catalytic efficiency of surface-active enzymes. Activity of Chromobacterium viscosum lipase (CV-lipase) was estimated in several mixed reverse micelles prepared from CTAB and four different nonionic surfactants, Brij-30, Brij-92, Tween-20, and Tween-80/water/isooctane/n-hexanol at different z ([cosurfactant]/[surfactants]) values, pH 6 (20 mM phosphate), 25 degrees C across a varying range of W0 ([water]/[surfactants]) using p-nitrophenyl-n-octanoate as the substrate. Lipase activity in mixed reverse micelles improved maximum up to approximately 200% with increasing content of non-ionic surfactants compared to that in CTAB probably due to the reduced positive charge density as well as plummeted n-hexanol (competitive inhibitor of lipase) content at the interfacial region of cationic W/O microemulsions. The highest activity of lipase was observed in CTAB (10 mM) + Brij-30 (40 mM)/isooctane/n-hexanol)/water system, k2 = 913 +/- 5 cm3 g-1 s-1. Interestingly, this observed activity is even higher than that obtained in sodium bis (2-ethyl-1-hexyl) sulfosuccinate (AOT)/n-heptane reverse micelles, the most popular W/O microemulsion in micellar enzymology. To ascertain the influence of non-ionic surfactants in improving the activity of surface-active enzymes is not limited to lipase only, we have also investigated the catalytic activity of Horseradish peroxidase (HRP) in different mixed W/O microemulsions. Here also following the similar trend as observed for lipase, HRP activity enhanced up to 2.5 fold with increasing concentration of nonionic surfactants. Finally, the enzyme activity was correlated with the change in the microenvironment of mixed reverse micelles by steady-state fluorescence study using 8-anilino-1-napthalenesulphonic acid (ANS) as probe.     

Probing the relationship between interfacial concentrations and lipase activity in cationic W/O microemulsions: a quantitative study by chemical trapping

Interfacial concentrations and/or space: which one is the predominant factor in regulating lipase activity at the water-oil interface? This work is an endeavor toward probing the relationship between lipase activity and interfacial concentrations in cationic water-in-oil (W/O) microemulsions through quantitative study by a chemical trapping method. The interfacial concentrations of water ([H2Oi]), bromide ([Bri-]), and n-hexanol ([HexOHi]) were estimated in the W/O microemulsions of six surfactants with varying headgroup architecture and hydrophilicity across a wide W0 ([H2O]/[surfactant]) range. The surfactants were prepared by the replacement of methyl groups of cetyltrimethylammonium bromide (1) by n-propyl (2-4), one hydroxyethyl (5), and one methoxyethyl (6) group. The estimated [H2Oi] was found not to change much (30.0-36.7 M) with the variation in headgroup hydrophilicity or size from 1-5. However, [Bri-] was found to increase with a decrease in the degree of dissociation (alpha), being higher for 1 and 5 (2.4-3.3 M) and relatively lower (0.9-1.9 M) for others depending on W0. Interestingly, [H2Oi] was found to be little higher (41.5-42.2 M) in the case of 6. The present study elucidates the importance of interfacial water and counterion concentrations in modulating the lipase activity in reverse micelles. In our previous report, the lipase activity was found to increase from 1-4 and in 6, whereas that observed in 5 was comparable with 1, being largely regulated by the surfactant head group size (Das, D.; Roy, S.; Mitra, R. N.; Dasgupta, A.; Das, P. K. Chem.-Eur. J. 2005, 11, 4881). The only other parameter that increased distinctly with lipase activity is the headgroup size, not [H2Oi]. Thus, the role of [H2Oi] in comparison to the surfactant's headgroup size is not found to be that significant. Moreover, the lower [Bri-] in 2-4 and 6 perhaps enhances the probability of enzyme and substrate localization at the interface, leading to higher lipase activity.     

纳米SiO2与阳离子表面活性剂的相互作用及其诱导的正辛烷-水乳状液的双重相转变

研究了3种不同结构的水溶性阳离子表面活性剂对纳米二氧化硅颗粒的原位表面活性化作用, 它们分别是单头单尾的十六烷基三甲基溴化铵(CTAB)、单头双尾的双十二烷基二甲基溴化铵(di-C12DMAB)和双头双尾的Gemini型阳离子三亚甲基-二(十四酰氧乙基溴化铵)(II-14-3), 并通过测定Zeta电位、吸附等温线及接触角等参数对相关机理进行了阐述. 结果表明, 阳离子表面活性剂吸附到颗粒/水界面形成以疏水基朝向水的单分子层, 从而增强了颗粒表面的疏水性是原位表面活性化的基础. 通过吸附CTAB和II-14-3, 颗粒的疏水性适当增强, 能吸附到正辛烷/水界面稳定O/W(1)型乳状液; 而通过吸附di-C12DMAB所形成的单分子层更加致密, 颗粒的疏水性进一步增强, 进而使乳状液从O/W(1)型转变为W/O型; 当表面活性剂浓度较高时, 由于链-链相互作用, 表面活性剂分子将在颗粒/水界面形成双层吸附, 使颗粒表面变得亲水而失去活性, 但此时体系中游离表面活性剂的浓度已增加到足以单独稳定O/W(2)型乳状液的程度. 因此当采用纳米二氧化硅和di-C12DMAB的混合物作乳化剂时, 通过增加di-C12DMAB的浓度即可诱导乳状液发生O/W(1)→W/O→O/W(2)双重相转变.     

Head-group size or hydrophilicity of surfactants: the major regulator of lipase activity in cationic water-in-oil microemulsions

To determine the crucial role of surfactant head-group size in micellar enzymology, the activity of Chromobacterium Viscosum (CV) lipase was estimated in cationic water-in-oil (w/o) microemulsions of three different series of surfactants with varied head-group size and hydrophilicity. The different series were prepared by subsequent replacement of three methyl groups of cetyltrimethylammonium bromide (CTAB) with hydroxyethyl (1-3, series I), methoxyethyl (4-6, series II), and n-propyl (7-9, series III) groups. The hydrophilicity at the polar head was gradually reduced from series I to series III. Interestingly, the lipase activity was found to be markedly higher for series II surfactants relative to their more hydrophilic analogues in series I. Moreover, the activity remained almost comparable for complementary analogues of both series I and III, though the hydrophilicity was drastically different. Noticeably, the head-group area per surfactant is almost similar for comparable surfactants of both series I and III, but distinctly higher in case of series II surfactants. Thus the lipase activity was largely regulated by the surfactant head-group size, which plays the dominant role over the hydrophilicity. The increase in head-group size presumably allows the enzyme to attain a flexible conformation as well as increase in the local concentration of enzyme and substrate, leading to the higher efficiency of lipase. The lipase showed its best activity in the microemulsion of 6 probably because of its highest head-group size. Furthermore, the observed activity in 6 is 2-3-fold and 8-fold higher than sodium bis(2-ethyl-1-hexyl)sulfosuccinate (AOT) and CTAB-based microemulsions, respectively, and in fact highest ever in any w/o microemulsions.     

STATISTICAL MECHANICAL MODEL THEORY OF THE STABILITY OF O/W AND W/O MICROEMULSIONS

A theoretical model to clarify the molecular origin of the mechanical and thermal stabilities of O/W or W/O microemulsion is proposed in which the low concentration of surfactants (emulsifiers) is limited. We assume only a short range interaction between surfactants and a bending stiffness energy which expresses the deformation energy from a preferable monolayer membrane curvature. We have found an interrelation among the interfacial pressure, Δp, of the monolayer due to the adsorption of surfactants in the microemulsion interface, interfacial tensions of oil-water interface and of the microemulsion, and the bending stiffness energy. We conclude that the interfacial tension and the stable form of the microemulsions (O/W type or W/O type) are infuenced largely by the effect of the bending stiffness energy. The interrelationship between the therraodynamical and mechanical stabilities of microemulsions is clarified by the use of our assumption.     

Conductivity of water-in-oil microemulsions stabilized by mixed surfactants

The electrical conductivity of D2O-in-n-heptane microemulsions stabilized by cationic/nonionic surfactant mixtures was studied as a function of D2O content, surfactant concentration, and surfactant mixture composition. The surfactants employed were cationic di-n-didodecyldimethylammonium bromide, DDAB, nonionic poly(oxyethylene) monododecyl ethers, C12EJ, with J=3-8 and 23, nonionic polymeric surfactants of the type PEO-PPO-PEO (Pluronic), and the reverse structure analogues (Pluronic R). Qualitative structural information was drawn from a comparison between the measured conductivity and that predicted by the charge fluctuation model for spherical droplets. The conductivity versus water content curves were found to be typical for water-in-oil systems composed of spherical droplets. From the effect of blending nonionic surfactant with DDAB on the measured conductivities, it was concluded that microemulsion conductivity is independent of the concentration of cationic surfactant (DDAB). This finding agrees well with theoretical microemulsion conductivity models.     

Nonionic Microemulsion: Mechanism of Formation and Percolation

A series of microemulsions, both W/O and O/W, based on nonionic surfactants of the form (NP(EO)_n), were prepared using the titration method. Mixing a constant weight of surfactant with a constant volume of the dispersed phase and an initial volume of continuous phase produces an emulsion, which is titrated to clarity with another surfactant (cosurfactant). Plotting (a) the volume of cosurfactant necessary to transform an emulsion into a microemulsion containing a fixed volume of dispersed phase and constant weight of surfactant versus (b) different initial continuous-phase volumes yields a straight line. Extrapolating from experimentally determined values for the cosurfactant volume to the value corresponding to a zero-volume continuous phase allows the determination of the surfactant molar composition and the average number of ethylene oxides (EO) per nonylphenol adsorbed at the interface. Using a surfactant with the same number of ethylene oxides yields a single-surfactant microemulsion. Measurement of surfactants transmittance in the oil and water phases demonstrates that microemulsification occurs when the surfactant interfacial film is equally soluble in the two phases. Surface pressure measurements reveal that oil penetration impedes formation of O/W microemulsions with n-tetradecane or n-hexadecane as dispersed phase. Conductance, particle size, and transmittance measurements show that above a certain dispersed-phase volume percolation of the microemulsion occurs.     

Phase Behavior of n‐Butanol/n‐Octane/Water/Cationic Gemini Surfactant System

Phase diagrams of the n‐butanol/n‐octane/water/(12‐3‐12,2Br^?1) system were determined, where n‐octane usually represents oil (O), 12‐3‐12,2Br^?1 is a gemini cationic surfactant trimethylene‐1,3‐bis(dodecyldimethyl ammonium bromide) abbreviated as S, and n‐butanol is a co‐surfactant written as A. Effects of the weight ratio of gemini surfactant to cosurfactant, S/A, and of temperature on the phase behavior were studied. The microemulsion structures including O/W, bi‐continuous (B.C.), W/O, and liquid crystal were determined by the conductivity method and polarization measurement. Experimental results show that the gemini surfactant, used facilitates the formation of microemulsions compared with its corresponding monomeric surfactant, n‐dodecyl trimethylammonium bromide (DTAB). When S/A=1/1, and the total concentration of gemini surfactant and alcohol is 20–40%, microemulsions with higher water content can form in a wider region. When the temperature increases, the size and position of each type of microemulsion region changes notably.     

Effects of Mixed Anionic-Cationic Surfactants and Alcohol on Solubilization of Water-in-oil Microemulsions

The solubilization of water in w/o microemulsions formed with mixed-surfactants containing one anionic and one cationic surfactant and alcohol was studied as a function of alkyl chain length of oil (C6 to C16), mixed-surfactant (sodium dodecyl sulfate, SDS, and cetyltrimethylammonium bromide, CTAB, or cetylpyridinium bromide CPB), and alcohol (1-butanol, 1-pentanol, 1-hexanol). The results show that the solubilization of water in microemulsion systems increases significantly with the mixed-surfactants due to the synergistic effect resulting from the strong Coulombic interactions between cationic and anionic surfactants and the solubilizing efficiency increases as the chain length or concentration of alcohol increases. With increasing the oil chain length the solubilization for water increases, decreases, and has the chain length compatibility effect when the systems contain 1-hexanol, 1-butanol, 1-pentanol, respectively. The total solubilizing capacity increases as the surfactant concentration (keep the ratio of SDS to butanol constant) increases.     

Effect of surfactant structure on catalysis of microemulsion for photoisomerization of trans-stilbene

In this study,the photoisomerization of trans-sfilbene was carried out in water in oil (W/O) microemulsions by using sodium dodecyl sulfate (SDS),dodecyl trimethyl ammonium bromide (DTAB) and cetyl trimethyl ammonium bromide (CTAB) as surfactant,respectively.The catalytic effect of microemulsion on this reaction is closely related to the structure of surfactant.When there is no photosensitizer 9,10-dicyanoanthracene (DCA),the surfactant with shorter hydrophobic chain is preferred,while in the presence of DCA,the surfactant with anionic polar group is preferred.     

乙酰水杨酸在微乳液中水解动力学研究

用紫外分光光度法研究了乙酰水杨酸在十六烷基三甲基溴化铵(CTAB)/正丁醇/25%正辛烷/H2O微乳液体系中水解动力学, 探讨了反应机理。结果表明,微乳液结构和结构转变点对乙酰水杨酸水解有影响。水解速率在油包水(W/O)微乳液结构介质中较大, 且随水含量增加而减小。而水解反应速率转变点发生在微乳液结构由W/O到B. C. 再到O/W转变点处, 认为是水解反应机理不同和界面膜极性改变造成的。     

Microemulsion polymerization of acrylamide and styrene: Effect of the structures of reaction media

Isothermal phase diagrams of the system cetyltrimethylammonium bromide (CTAB)/n‐butanol/n‐octane/water were constructed, and the effect of the oil (n‐octane) contents on the microemulsions was studied at 40 °C. We determined the microemulsion structures of two systems, CTAB/n‐butanol/10% n‐octane/water and sodium dodecyl sulfonate (As)/n‐butanol/20% styrene/water, by conductivity measurements to investigate the polymerization of acrylamide and styrene in the two microemulsion systems. The polymerization kinetics of the water‐soluble monomer acrylamide in CTAB micelles and the different CTAB/n‐butanol/10% n‐octane/water microemulsion media [water‐in‐oil (W/O), bicontinuous (BC), and oil‐in‐water (O/W)] were studied with water‐soluble sodium bisulfite as the initiator. The maximum polymerization rate in CTAB micelles was found at the second critical micelle concentration. A mechanism of polyacrylamide formation and growth was proposed. A connection between the structures of the microemulsions and the polymerization rates was observed; the maximum polymerization rate occurred at two transition points, from W/O to BC and from BC to O/W, and the polyacrylamide molecular weights, which depended on the structures of the microemulsions, were also found. A square‐root dependence of the polymerization rates on the initiator concentrations was obtained in CTAB micelles and O/W microemulsion media. The polymerization of the oil‐soluble monomer styrene in different As/n‐butanol/20% styrene/water microemulsion media (W/O, BC, and O/W) was also investigated with different initiators: water‐soluble potassium persulfate and oil‐soluble azobisisobutyronitrile. A similar connection between the structures of the microemulsions and the conversions of styrene in CTAB/n‐butanol/10% n‐octane/water for the polymerization of acrylamide was observed again. The structures of the microemulsions had an important role in the molecular weights and sizes of polystyrene. The polystyrene particles were 10–20 nm in diameter in BC microemulsion media and 30–60 nm in diameter in O/W microemulsion media according to transmission electron microscopy. We determined the solubilization site of styrene in O/W microemulsion drops by ¹H NMR spectra to analyze the results of the microemulsion polymerization of styrene. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3320–3334, 2001     

Structural investigations of charged O/W microemulsion droplets

Structure and properties of charged oil-in-water (O/W) microemulsions have been investigated and a short review of the work done on such systems is given. A particular system made up from a zwitterionic surfactant and hydrocarbon which becomes charged upon the addition of either cationic or anionic surfactant has been studied. A particular feature of this microemulsion system is that the charge density on the droplets can be fixed at a desired value in an easily controllable fashion. These systems have been characterized ed by means of light scattering, small - angle neutron scattering, interfacial tension measurements, electric conductivity, and viscosity measurements. The experiments showed that the aggregates remain of constant size over a large concentration region, i. e. from 0 to ≈ 30 wt %. Moreover there size is not much changed by the addition of the ionic surfactant. The interactions in this microemulsion system could be described by a hard sphere interaction with an additional DLVO - potential term that accounts for the electrostatic repulsion.     

Size-controlled synthesis of CuO–ZrO<Subscript>2</Subscript> nanoparticles prepared through reverse micelle method

In this research, CuO–ZrO₂ nanoparticles are synthesized using microreactors made of surfactant/water/cyclohexane microemulsions. The effect of different microemulsion variables on the particle size and its distribution, such as water-to-surfactant molar ratio (W ₀) and different surfactants are discussed. Three different surfactant types including cationic (CTAB), anionic (AOT), and nonionic (Brij56) are used. Also a different amount of water to surfactant in nano composite synthesis is used. The powders were characterized by DTA/TG, XRD, SEM, EDS, TEM and BET techniques and their physical properties are compared. The results show a decrease of particles size in presence of cationic surfactant. Narrow particles size distribution of the resultant CuO–ZrO₂ nanocomposite in presence of cationic surfactant, anionic and nonionic surfactant is compared. Also for AOT surfactant, by raising water to surfactant molar ratio the particles size is increased and the optimum ratio is H₂O: Surfactant = 0.32:0.055, respectively.     

维生素C对表面活性剂体系相行为的影响

维生素Ｃ（ＶＣ）能提高表面活性剂十六烷基三甲基溴化铵（ＣＴＡＢ）在水中的溶解度,具有助溶作用;且能提高ｎ－Ｃ５Ｈ１１ＯＨ在Ｏ／Ｗ微乳液中的增溶量和水在Ｗ／Ｏ微乳液中的增溶量,Ｏ／Ｗ与Ｗ／Ｏ微乳液区域同时扩大,具有助溶－增溶作用。ＶＣ的助溶作用与助溶－增溶作用均具有一定的选择性,只对阳离子表面活性剂ＣＴＡＢ体系有效,ＶＣ助溶－增溶作用的机理是同时增加Ｗ／Ｏ和Ｏ／Ｗ微乳液的稳定性和层状液晶向双连续结构     

CTAB反相微乳液中水辛烷分子的自扩散研究

利用电导测量确定了CTAB/正丁醇/正辛烷/水四组分体系的相态,在反相微乳液区有明显的渗滤现象,通过脉冲梯度场核磁共振方法研究了反相微乳液中水和辛烷分子的自扩散行为,采用双指数拟合得出辛烷的自扩散系数。对于体系中出现的渗滤现象以及水和辛烷分子自扩散系数反常的原因,从分子水平上进行了解释。水和自扩散系数(2～7×10^-10m·s^-1)比一般文献值高,其原因：一是水在油相中有较大的溶解度;二是渗滤现象的存在,由于液滴间相互作用的增强和：粘性“碰撞而导致液滴的融合,以及由此而形成的瞬时水相连续通道,使水的自扩散系数增大。而辛烷自扩散系数比一般文献值小,则是由于在微乳液液滴的栅栏中表面活性剂分子烃链与辛烷分子间范德华引力所造成。     

Structural and spectroscopic investigation of ZnS nanoparticles grown in quaternary reverse micelles

ZnS nanoparticles were synthesized in four component "water in oil" microemulsions formed by a cationic surfactant (cetyltrimethylammonium bromide, CTAB), a cosurfactant (pentanol or butanol), n-hexane and water. The effect of various parameters (nature of cosurfactant, water/surfactant W(0), and alcohol/surfactant P(0)) on the formation and stability of ZnS nanoparticles was investigated thoroughly. UV-Vis spectroscopy was employed to directly follow the formation of ZnS systems in the microemulsions. Thus, particle size was estimated from the position of the first excitonic transition by employing an approximate finite-depth equation and an empirical correlation, giving average diameters in the ranges 2.3-2.5 and 3.0-3.5nm, respectively. Stable ZnS nanoparticles were obtained by employing low water and high cosurfactant amounts. This suggests that at high concentration the cosurfactant molecules act as capping agents on the surface of the inverse micelles, while low water amounts are needful to obtain water droplets with a radius close to that of the interfacial film spontaneous curvature. HRTEM analysis showed that the samples are formed by a few crystalline ZnS nanoparticles of spherical shape, embedded in and amorphous organic matrix, with a coherent scattering domain between 2 and 4nm.     

A novel water-in-ionic liquid microemulsion and its interfacial effect on the activity of laccase

It is of great significance to develop an appropriate water-in-ionic liquid (W/IL) microemulsion suitable for the expression of the catalytic activity of a given enzyme. In this paper, the phase diagram of a new AOT/Triton X-100/H(2)O/[Bmim][PF(6)] pseudo ternary system is presented. With the aid of nonionic surfactant Triton X-100, AOT could be dissolved in hydrophobic ionic liquid [Bmim][PF(6)], forming a large single phase microemulsion region. The water-in-[Bmim][PF(6)] (W/IL) microemulsion domain was identified electrochemically by using K(3)Fe(CN)(6) as a probe. The existence of W/IL microemulsions was demonstrated spectrophotometrically by using CoCl(2) as a probe. New evidences from the FTIR spectroscopic study, which was first introduced to the W/IL microemulsion by substituting D(2)O for H(2)O to eliminate the spectral interference, demonstrated that there existed bulk water at larger ω(0) values (ω(0) was defined as the molar ratio of water to the total surfactant) in the W/IL microemulsion, which had remained unclear before. In addition to the inorganic salts, biomacromolecule laccase could be solubilized in the W/IL microemulsion. The laccase hosted in the microemulsion exhibited a catalytic activity and the activity could be regulated by the composition of the interfacial membrane.     

A nucleophilic substitution reaction in microemulsions based on either an alcohol ethoxylate or a sugar surfactant

A nucleophilic substitution reaction between 4-tert-butylbenzyl bromide and a series of iodide salts has been performed in oil-in-water microemulsions based on either a fatty alcohol ethoxylate or a sugar surfactant. The reaction kinetics was compared with the kinetics of the same reaction performed in a microhomogeneous reaction medium, d-MeOH. Previous results showing a particularly high reactivity in the microemulsion based on the fatty alcohol ethoxylate was confirmed. It was shown that in both microemulsions the reaction rate was almost independent of the choice of counterion to iodide. This indicates that complexation of the cation with the surfactant headgroup, which, in particular, could have taken place with surfactants containing oligooxyethylene chains (a “crown ether effect”), seems not to be of importance.

¹²⁷I NMR studies, as well as quadrupole splitting experiments performed by ²H NMR, indicate that there is a certain accumulation of iodide at the oil–water interface of the microemulsions. It is difficult to draw any quantitative conclusions in this respect, however.

The results obtained in this study, combined with results from previous investigations of the same reaction, indicate that the unexpectedly high reactivity obtained in the microemulsion based on a surfactant containing an oligooxyethylene headgroup is most probably due to the nucleophile being poorly solvated when present in the headgroup layer of such a microemulsion. Poorly solvated anions are known to be highly reactive nucleophiles.