透明抗静电多功能超疏水薄膜的制备

采用提拉法在聚酰亚胺薄膜表面分步涂覆了银纳米线及疏水纳米二氧化硅, 分别构筑了导电网络及超疏水涂层, 制备了超疏水抗静电透明薄膜. 研究结果表明, 超疏水抗静电透明薄膜保持了较高的透光性, 其透光率高于90%. 同时, 银纳米线网络的构筑有效增加了超疏水抗静电透明薄膜的导电性, 使其表面电阻介于10⁶~10¹⁰ Ω之间, 达到了抗静电要求. 水滴在该薄膜表面静态接触角高达156.4°, 滚动角小于1°, 展现了优异的超疏水特性. 通过导电网络及疏水涂层的构筑, 实现了透明及抗静电超疏水多功能的统一.     

具有超疏水表面的硅/二氧化硅层次结构薄膜

目前报道的硅基材料的超疏水表面主要是通过制备粗糙微观结构,并在其表面修饰表面能相对较低的有机物两个步骤来实现的,在户外等实际环境中应用时存在由于表面修饰有机物的降解而逐渐失去超疏水性的问题.本工作以液态金属锡作为生长衬底,通过化学气相沉积(CVD)法制备了一种具有超疏水性能的硅基薄膜结构.利用扫描电镜(SEM),透射电镜(TEM)以及X射线衍射(XRD)等手段对产物的表面形貌和组成结构进行分析发现,薄膜表面由竖直生长的硅/二氧化硅(Si/SiO2)核壳层次结构组成.采用Cassie理论模型对其超疏水性能的产生提出了可能的解释.发现构成薄膜表面的Si/SiO2层次结构单元的形貌是影响超疏水性能的重要因素.相对于以前报道的硅基材料的超疏水表面,这种新结构的超疏水性能不依赖于表面化学修饰,有望拓宽硅基材料的应用环境.     

浸蚀多孔金属铝模板制备超亲水/超疏水镍阵列材料

本文论述了用一种新型的金属铝隧道孔模板制备较大面积的纳/微分级结构阵列材料。结合化学镀法在该高纯铝隧道孔模板中制备了具有微纳米阵列结构的金属镍薄膜。研究发现,制备的镍阵列薄膜材料表面呈现超亲水性,以低表面能氟硅烷修饰后,该表面变为超疏水性。     

锂镍钴复合氧化物锂离子电池正极材料的研究

本文报道了以碱式碳酸镍、碱式碳酸钴和碳酸锂为原料 ,柠檬酸为络合剂的新溶胶凝胶法制备复合锂镍钴氧化物锂离子电池正极材料 .氧气流中制备的LiNi0 .8Co0 .2 O2 具有高的循环容量 (～ 190mAhg 1)     

超疏水超亲油铜网的制备及其在油水分离中的应用（英文）

以铜网为基底,通过浸涂法在其表面制得超疏水超亲油有机-无机复合薄膜,水滴、油滴在其表面的接触角分别为152°和10°。线性低密度聚乙烯-SiO_2纳米球构成的复合阶层结构及低表面能线性低密度聚乙烯涂层的协同作用使铜网产生独特的润湿性。该铜网具有很好的自清洁性和抗腐蚀性,可用于油水混合物的有效分离。与传统方法相比,该方法制备超疏水-超亲油薄膜方法简单、成本低、无氟,有望在实践中得到应用。     

超疏水超亲油铜网的制备及其在油水分离中的应用

以铜网为基底,通过浸涂法在其表面制得超疏水超亲油有机-无机复合薄膜,水滴、油滴在其表面的接触角分别为152°和10°。 线性低密度聚乙烯-SiO₂纳米球构成的复合阶层结构及低表面能线性低密度聚乙烯涂层的协同作用使铜网产生独特的润湿性。 该铜网具有很好的自清洁性和抗腐蚀性,可用于油水混合物的有效分离。 与传统方法相比,该方法制备超疏水-超亲油薄膜方法简单、成本低、无氟,有望在实践中得到应用。     

喷砂-阳极氧化-氟化处理构筑铝合金超疏水表面

为研究复合法制备超疏水表面过程中主要工艺参数对表面形貌及超疏水性能的影响, 开发了一种喷砂-阳极氧化复合方法, 在铝合金表面构筑了微米-纳米二级结构, 经氟化处理后获得了超疏水特性. 结果表明, 喷砂处理在铝合金表面通过冲蚀的凹坑构筑出微米结构, 阳极氧化则在铝合金表面通过蜂窝状氧化膜构筑纳米结构. 但单纯构筑粗糙结构或单纯改变表面化学组成均不能在铝合金表面获得超疏水特性. 单纯的微米结构或纳米结构, 即使有低表面能聚合物修饰也不能获得超疏水特性. 只有微米-纳米二级结构和低表面能聚合物的协同作用, 才能有效构筑铝合金超疏水表面. 这种铝合金与水滴接触时, 形成的气阱可减小固体表面与水滴的接触面积, 降低表面与水滴间的热量交换, 从而减缓水分子的凝结, 提高铝合金的抗霜冻性. 同时, 气阱还可有效减缓海水的腐蚀, 提高铝合金的耐海水腐蚀性.     

染料敏化的TiO2纳米管薄膜的光电浸润性

采用阳极氧化法在钛箔表面制备TiO2纳米管阵列, 并在其表面修饰N3染料(Ruthenium dye)作敏化剂, 用氟硅烷来提高表面疏水性, 获得超疏水薄膜. SEM测定结果表明, 纳米管薄膜具有各向异性浸润结构, 同时阳极氧化的非均匀性增加了表面的粗糙度. UV-Vis吸收光谱及电化学阻抗谱结果表明, 薄膜具有优异的光电性能. 通过施加超过一定阈值的电压, 液滴在薄膜表面由超疏水状态转变为亲水状态. 利用光电协同激励作用时, 阈值电压比单独使用电激励时降低了10 V, 这是使用高效的N3染料光电敏化层的结果.     

微纳米结构复合表面的疏水-冰性能

通过软复型和水热法制备出一种由有机材料和ZnO纳米棒组成的微纳米结构复合表面,这种表面的微米结构是周期为300μm、高度为70μm的锯齿状结构,ZnO纳米线的直径为300~500 nm,长度为2~3μm.这种有机材料和ZnO纳米线复合成的表面经过全氟硅烷修饰后,具有良好的低黏滞特性和低温超疏水性(约为150°)以及较长的结冰延时性(6000~7630 s),实验结果对设计表面低温疏水/疏冰材料具有参考价值.     

微结构与表面修饰对二氧化硅多孔薄膜疏水性能的影响

通过引入聚乙二醇(PEG)改性传统二氧化硅(SiO2)溶胶,得到了粒径分布较宽且粒径可控的溶胶。比较了六甲基二硅氮烷(HMDS)溶胶内修饰和薄膜表面修饰以及溶胶粒径对SiO2薄膜疏水性能的影响。采用动态光散射粒度仪定量测试了二氧化硅溶胶老化过程中粒度的变化,用原子力显微镜、接触角测试仪、红外光谱仪、紫外-可见-近红外分光光度计分别对薄膜的表面形貌、表观静态接触角、薄膜成分及透光率等进行了测量。结果表明:PEG的添加可有效增大溶胶粒度从而增大薄膜的粗糙度,提高薄膜的疏水性。表面修饰效果受修饰方式和SiO2粒径影响,粒径较小时有利于溶胶内修饰,粒径较大时有利于对薄膜修饰。经过表面修饰剂(HMDS)的气氛处理得到了接触角为152°的超疏水薄膜,而且相比溶胶内修饰可以减小薄膜透光率的损失。     

Effect of surface roughness and chemical composition on the wetting properties of silicon-based substrates

The article reports on the wetting properties of silicon-based materials as a function of their roughness and chemical composition. The investigated surfaces consist of hydrogen-terminated and chemically modified atomically flat crystalline silicon, porous silicon and silicon nanowires. The hydrogenated surfaces are functionalized with 1-octadecene or undecylenic acid under thermal conditions. The changes occurring upon surface functionalization are characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) spectroscopy and water contact angle measurements. By increasing the surface roughness, the static water contact angle increases. The combination of high surface roughness with chemical functionalization with water repellent coating (1-octadecene) enables reaching superhydrophobicity (water contact angle greater than 150°) for silicon nanowires.     

Bio-inspired fabrication of well-oriented ZnO nanorod arrays film and its superhydrophobicity and superhydrophilicity

A highly oriented ZnO nanorod array film was fabricated on glass substrate by combinations of Sol–Gel and hydrothermal. The film exhibits perfect superhydrophobicity with a contact angle of 155° and a glide angle of 4° after being surface modified by fluoroalkylsilane, which is similar with wings’ property and structures of large yellow spots mosquitoes. Interestingly, the ZnO nanorods film were converted from superhydrophobicity into superhydrophilicity under ultraviolet light for 2 h due to the decomposition of fluoroalkyl chain of fluoroalkylsilane and the photosensitivity of ZnO surface. The transition mechanisms of wettability are discussed on the basis of correlated theories.     

A facial approach to fabricate superhydrophobic aluminum surface

A facial chemical etching method was developed for fabricating superhydrophobic aluminum surfaces. The resultant surfaces were characterized by scanning electron microscopy, water contact angle (WCA) measurement, and optical methods. The surfaces of the modified aluminum substrates exhibit superhydrophobicity, with a WCA of 154.8° ± 1.6° and a water sliding angle of about 5°. The etched surfaces have binary structure consisting of the irregular microscale plateaus and caves in which there are the nanoscale block‐like convexes and hollows. The superhydrophobicity of aluminum substrates occurs only in some structures in which the plateaus and caves are appropriately ordered. The resulted surfaces have good self‐cleaning properties. The results demonstrate that it is possible to construct superhydrophobic surface on hydrophilic substrates by tailoring the surface structure to providing more spaces to trap air. Copyright © 2009 John Wiley & Sons, Ltd.     

Highly transparent superhydrophobic thin film with low refractive index prepared by one-step coating of modified silica nanoparticles

An easy and effective method to prepare superhydrophobic thin film has been developed. The film with optically transparent and low refractive index was composed by one-step coating with modified silica nanoparticles. The silica nanoparticles were prepared by sol–gel process of hydrolysis and condensation of alkoxysilane compounds and then surface modification silica nanoparticles, 50 ± 10 nm, were accomplished using methoxytrimethylsilane (MOTMS). Water contact angle of film increased with the weight of MOTMS of silica sol. When the weight of MOTMS was optimized, the water contact angle and sliding angle of film were 152.8° and less than 10°, respectively. The transmittance of film was also increased as compared to the un-coated microscope glass slide, from 91 to 93.5 %. The refractive index of the film was approximately 1.09 as measured by ellipsometer. The superhydrphobic thin film was also successfully made by using spray coating and the water contact angle of this film was more than 160°. Surface morphology of difference coating methods, dip and spray, were studied. Our result suggests that the film can be applied for superhydrophobicity and optical applications.     

Fabrication and Electrowetting Properties of Poly Si Nanostructure Based Superhydrophobic Platform

Poly-silicon based superhydrophobic surface (water contact angle >150°) is being fabricated and its electrowetting properties have been studied. The polysilicon thin film has been deposited over patterned gold electrodes. The polysilicon film is structured to form nanoscale features using Reactive Ion Etching. A thin film of HfO₂ high k-dielectric is deposited over the structured polysilicon surface. The surface was chemically modified with Trichloro (1H, 1H, 2H, 2H-perfluorooctyl) silane (PFOS). Such a surface showed Superhydrophobic behavior with water contact angle of 172° and roll off angle <3°. The electrowetting properties of the fabricated device was studied by applying a DC voltage between the gold electrode and the droplet. The electrowetting commences when the applied voltage was 18 V and the contact angle is reduced to 152°. As the applied voltage was increased there was decrease in contact angles.     

溶胶凝胶法制备仿生超疏水性薄膜

通过溶胶-凝胶(Sol-Gel)法和自组装(Self-assembled)制备了具有超疏水性的薄膜, 水滴在该薄膜上的平衡静态接触角为155°～157°, 滑动角为3°～5°. 通过扫描电子显微镜(SEM)观察薄膜微观表面, 发现该薄膜表面分布了双层结构(Binary structure)的微纳米粗糙度的微凸体, 上表层微米微凸体的平均直径为0. 2 μm, 下表层纳米微凸体的平均直径约为13 nm, 其分布与荷叶表面的结构极其相似. 用X射线光电子能谱(XPS)对薄膜表面元素进行了成分分析, 结果表明, 其表面存在大量的F, Cl等元素, 它能显著降低薄膜表面的表面能. 薄膜超疏水性的原因可能是, 通过硅片经溶胶粒子表面制备的薄膜具有合适的表面粗糙度, 再经过全氟辛基三氯甲硅烷(FOTMS)化学修饰后, 薄膜表面能进一步降低, 这两个条件的有机结合就使得薄膜产生了超疏水性.     

CaCO_3颗粒模板法制备聚合物超亲水/超疏水表面

以碳酸钙(CaCO3)颗粒层为模板,运用简单的热压和酸蚀刻相结合的方法制备聚合物超亲水/超疏水表面.首先在玻璃基底上均匀铺撒一层CaCO3颗粒,以此作为模板,通过热压线性低密度聚乙烯(LLDPE)使CaCO3颗粒均匀镶嵌在聚合物表面,获得了超亲水性质;进一步经酸蚀得到了具有微米和亚微米多孔结构的表面,其水滴静态接触角(WCA)可达(152.7±0.8)°,滚动角小于3°,具备超疏水性质.表面浸润性能和耐水压冲击性能研究表明该超疏水表面具有良好的稳定性和持久性.用同样工艺微模塑/酸蚀刻其它疏水性聚合物,得到类似结果.     

泡沫镍载Co（OH）2纳米线的电化学电容性能

以无模板法制备了泡沫镍载Co(OH)2纳米线电极,利用扫描电镜(SEM)和透射电镜(TEM)观测了纳米线的表面形貌,利用X射线衍射(XRD)分析了Co(OH)2纳米线的结构,通过循环伏安、恒流充放电和交流阻抗测试了电极的电化学电容性能.结果表明:Co(OH)2呈线状生长,其直径约为300nm,长度约为8～10μm,密集地生长在泡沫镍骨架上.电流密度为10mA·cm-2时电极的放电比容量高达677F·g-1,循环500次后比容量仍保持在574F·g-1,电化学阻抗测试其电荷传递电阻仅为0.23Ω,500次循环后电荷传递电阻仅增加0.03Ω.     

冬瓜皮表面白霜的超疏水性研究

冬瓜是一种常见的蔬菜,大部分品种成熟时表面覆盖一层类似于"白霜"的粉末。本文使用扫描电镜、接触角测量仪、傅立叶变换红外光谱、X射线衍射仪等设备对冬瓜皮表面白霜的浸润性、结构形貌及其组成进行了研究,证实了冬瓜皮表面白霜的超疏水特性,水滴在其表面的接触角高达154.8±3.5°,且滚动角小于5°。研究表明,冬瓜皮表面的白霜呈现微纳米多级拓扑结构,主要由长链脂肪酸、长链烷烃酯类组成,这种微纳米拓扑结构和化学组成的协同作用决定了冬瓜皮表面的超疏水性。本工作可为进一步了解、设计此类结构材料提供数据积累。