亲/疏水不对称空心聚合物微球制备及磁性粒子装载研究

首先将(马来酸酐-醋酸乙烯酯共聚物)核/(马来酸酐-二乙烯基苯共聚物)壳微球的壳层外表面酐基烷基溴化,然后将核溶蚀、壳层内表面酐基水解,制得内表面含亲水羧基、外表面含烷基溴、具有微孔(Barrett-Joyner-Halenda平均孔径14.9nm)的空心聚合物微球.以此空心微球为微反应器,使Fe2+和Fe3+通过球壁...     

在空心聚苯乙烯微球表面电沉积Au-Cu双壳层（英文）

PS/Au/Cu双壳层核壳复合微球是在自制的电沉积装置中首先在空心聚苯乙烯微球模板上电沉积金形成PS/Au微球,然后再电沉积Cu。首先,PS/Au微球保持了较好的球形度,其中沉积层Au粗糙度低,且厚度达到5.6μm。由于Au和铜有相同的面心立方晶体结构,所以Cu沿着Au的晶体结构在PS/Au表面沉积。微球断面Au-Cu结合非常紧致,Cu的厚度为8.62μm,Au的厚度为4.04μm。PS/Au/Cu微球和Au-Cu双壳层的形貌、厚度,成分和粗糙度是通过3D体式显微镜,SEM、EDS和XRD表征,其结果显示PS/Au/Cu微球及双壳层Au-Cu均匀细致,粗糙度低。     

在空心聚苯乙烯微球表面电沉积Au-Cu双壳层

PS/Au/Cu双壳层核壳复合微球是在自制的电沉积装置中首先在空心聚苯乙烯微球模板上电沉积金形成PS/Au微球,然后再电沉积Cu。首先,PS/Au微球保持了较好的球形度,其中沉积层Au粗糙度低,且厚度达到5.6 μm。由于Au和铜有相同的面心立方晶体结构,所以Cu沿着Au的晶体结构在PS/Au表面沉积。微球断面Au-Cu结合非常紧致,Cu的厚度为8.62 μm,Au的厚度为4.04 μm。PS/Au/Cu微球和Au-Cu双壳层的形貌、厚度,成分和粗糙度是通过3D体式显微镜,SEM、EDS和XRD表征,其结果显示PS/Au/Cu微球及双壳层Au-Cu均匀细致,粗糙度低。     

在空心聚苯乙烯微球表面电沉积Au-Cu双壳层

PS/Au/Cu双壳层核壳复合微球是在自制的电沉积装置中首先在空心聚苯乙烯微球模板上电沉积金形成PS/Au微球,然后再电沉积Cu。首先,PS/Au微球保持了较好的球形度,其中沉积层Au粗糙度低,且厚度达到5.6 μm。由于Au和铜有相同的面心立方晶体结构,所以Cu沿着Au的晶体结构在PS/Au表面沉积。微球断面Au-Cu结合非常紧致,Cu的厚度为8.62 μm,Au的厚度为4.04 μm。PS/Au/Cu微球和Au-Cu双壳层的形貌、厚度,成分和粗糙度是通过3D体式显微镜,SEM、EDS和XRD表征,其结果显示PS/Au/Cu微球及双壳层Au-Cu均匀细致,粗糙度低。     

N掺杂空心TiO2微球的合成与表征

采用无皂乳液聚合合成的聚苯乙烯(PS)微球为模板、氨水/三乙醇胺为催化体系, 通过溶胶-凝胶方法合成了PS/TiO₂(核/壳)复合微球, 然后通过煅烧制备了N掺杂、锐钛型空心TiO₂微球. 在反应体系中三乙醇胺扮演双重角色, 既是TiO₂生成及包覆过程的抑制剂又是空心TiO₂微球的N掺杂剂. 改变氨水、三乙醇胺和钛酸正丁酯用量可控制TiO₂壳的形态和尺寸. 氨水用量增加, PS/TiO₂复合微球的壳表面变得粗糙|三乙醇胺用量增加, 壳表面变得光滑|钛酸正丁酯用量提高导致壳层变厚. 改变三乙醇胺用量可调节空心TiO₂微球中的N掺杂量|N掺杂空心TiO₂微球具有可见光响应和光催化作用.     

苯乙烯-丙烯酸酯-丙烯腈三元共聚物的合成及表征

在可控核聚变领域,惯性约束聚变(ICF)用空心靶球的研究[1-3]十分活跃。以聚苯乙烯为基材制备ICF有机物空心靶球已有广泛的研究,微球的制备技术、工艺等都已相当成熟,但聚苯乙烯阻气性差,难以阻挡氢同位素的扩散,不能满足ICF靶球的需要。目前应用比较好的ICF靶球制备条件极为苛刻,工艺复杂[4]。丙烯腈、丙烯酸酯、偏二氯乙烯、醋酸乙烯酯等一类单体的均聚物都有较好的阻气性[5],本文探讨苯乙烯与丙烯腈、丙烯酸酯类单体的共聚方法,研究了共聚物的一些基本性能。1　实验部分1 1　试剂及仪器苯乙烯、丙烯腈、丙烯酸甲酯、丙烯酸丁酯均…     

聚苯乙烯/银核/壳复合微球的制备及其表征

通过分散聚合法制备了单分散性好,粒径均一的聚苯乙烯(PS)微球.以PS微球为核,用浓硫酸进行表面改性,使其表面带有负电.加入一定量的[Ag(NH3)2]+溶液,由于静电吸引,使其吸附在PS微球表面,通过化学还原的方法制备了PS/Ag核/壳结构复合微球.采用透射电镜(TEM)、扫描电镜(SEM)、红外光谱(IR)、X射线衍射(XRD)以及紫外-可见光谱对PS/Ag复合微球进行表征.结果表明:通过PS微球的表面改性,在其表面引入了磺酸基团,提高了微球表面的电负性和亲水性,对包覆过程起到了很好的促进作用;通过稳定剂(PVP)和不同还原剂(一缩二乙二醇DEG和乙二醇EG)的使用,形成的PS/Ag核/壳复合微球形貌不一样,同时研究表明制备出的PS/Ag复合微球可以用于催化剂催化还原有机染料溶液,表现出很好的催化活性.     

微米级PS-PEDOT核壳型导电微球的合成与拉曼表征

以分散聚合法制备的微米级聚苯乙烯(PS)微球为模板、3,4-乙烯二氧噻吩(EDOT)为单体、过硫酸铵(APS)为引发剂,通过氧化聚合制备了PS-PEDOT核壳型复合导电微球。采用扫描电镜、透射电镜等对导电微球的形貌和结构进行了表征,重点采用拉曼光谱研究了其核壳结构特征。并研究了超声分散、溶液pH以及单体配比对导电微球形貌的影响。实验结果表明:超声的引入可提高导电微球的单分散性,改善微球的形貌。随着pH的降低或单体配比的增加,导电聚合物在PS微球表面的负载量随之增加,当m(EDOT)/m(PS)由0.60增加到1.25时,导电微球的平均粒径由1.76μm增加到1.91μm。     

聚合物中空微球的制备及碱后处理因素的正交试验研究

首先采用种子乳液聚合法合成高羧基含量的核壳聚合物微球,然后利用碱液进行后处理,经渗透溶胀后可形成具有中空结构的聚合物微球,考察了单体加料工艺和聚合配方对聚合稳定性及微球形貌的影响,通过正交试验设计研究了不同的碱后处理条件对溶胀后微球形貌的影响程度,并进行了极差和方差分析.结果表明,控制单体加料速度和引入中间极性过渡层,有利于核壳聚合物微球的制备;碱液用量为影响溶胀后聚合物微球形貌的主要因素,碱处理温度次之,碱处理时间的影响相对较弱.当碱酸摩尔比为1~1.15,碱处理温度为80~90℃,碱处理时间为1~5 h时,制得的聚合物微球具有良好的中空结构.     

聚合物空心微球的研究进展

聚合物空心微球由于其独特的性质及其广阔的应用,近年来受到越来越多的关注.本文综述了近年来制备聚合物空心微球的方法,如:自组装法、模板法、微乳液法等.并简要介绍了聚合物空心微球在医学材料等方面的应用.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.