合成反铁磁Ni81Fe19/Co90Fe10/Ru/Co90Fe10/Ni81Fe19的研究

采用直流磁控溅射方法制备了一系列的合成反铁磁及以其为自由层的自旋阀.研究发现,在Ni81,Fe19与Ru层之间插入适当厚度的Co90Fe10层后,可有效地提高合成反铁磁两磁性层间的反铁磁耦合强度,得到具有饱和场日.更高、饱和磁化强度M.更低、热稳定性更好的合成反铁磁.另外,以这种合成反铁磁作自旋阀的自由层时,可有效提高自旋阀的稳定性.     

Ni81Fe19/Cr82Al18双层膜中的交换偏置

研究了直流磁控溅射法制备的Ni₈₁Fe₁₉/Cr₈₂Al₁₈双层膜中的交换耦合.样品的室温矫顽力与1/t^{3/2_FM(t_FM为铁磁层厚度）近似成正比例关系,从而表明在Ni₈₁Fe₁₉/Cr₈₂Al₁₈中交换耦合为铁磁/反铁磁界面的随机相互作用.另外还讨论了反铁磁层厚度对交换偏置的影响. 关键词：}     

BiFeO3/Ni81Fe19磁性双层膜中的交换偏置及其热稳定性研究

研究了磁场诱导生长的BiFeO₃/Ni₁₈Fe₁₉磁性双层膜中 的交换偏置及其热稳定性. 结果表明: BiFeO₃/Ni₁₈Fe₁₉双层膜中的交换偏置场H_ex未表现出明显的磁练习效应. 在负饱和磁场等待过程中, BiFeO₃/Ni₁₈Fe₁₉双层膜磁滞回线的前支和后支曲 线都随着在负饱和磁场中等待时间t_sat的增加向正场方向偏移. 交换偏置场H_ex的大小随着等待时间t_sat的增加而减小, 矫顽力H_c基本不变. 交换偏置场H_ex的大小随测量温度T_m的升高变化不明显, 表现出良好的热稳定性; 但矫顽力H_c随T_m的升高而显著减小. 良好的热稳定性应该来源于铁电性和反铁磁性间的共同耦合作用. 关键词： 多铁性 磁性薄膜 交换偏置 热稳定性     

双合成反铁磁结构及其对自旋阀巨磁电阻效应的影响

用直流磁控溅射方法制备了双合成反铁磁结构Co₉₀Fe₁₀(5 nm)/Ru(x nm)/Co₉₀Fe₁₀(3 nm)/Ru(y nm)/Co₉₀Fe₁₀(5 nm)(x=0.45,0.45,1.00; y=0.45,1.00,1.00)的系列样品,并对样品的性能及其作为钉扎层对自旋阀巨磁电阻(GMR)效应的影响进行了研究 关键词： 双合成反铁磁 自旋阀 巨磁电阻     

永磁性大块金属玻璃Nd60Al10Fe20Co10低 温磁性的研究

研究了Nd₆₀Al₁₀Fe₂₀Co₁₀ 大块金属玻璃 磁性随温度的变化关系，结果表明Nd₆₀Al₁₀Fe₂₀Co₁₀ 在室温下 表现为永磁性，随着温 度的降低，矫顽力和磁滞回线形状都有很大的变化.交流磁化率在18 K左右出现尖峰而且峰 值温度随频率变化，表明该大块非晶体系中存在自旋玻璃态. 关键词： 大块金属玻璃 低温磁化率 自旋玻璃     

真空退火对Ni80Fe20/Cu多层膜微结构的影响

用直流磁控溅射法在Si(001)衬底上制备了以Ta为缓冲层、含有15周期的Ni₈₀Fe₂₀（4nm)/Cu(6nm)多层膜.样品分别在150,250,350℃进行了真空退火处理.用低角和高角X射线衍射法研究了多层膜的微结构.结果表明,所有样品均有较好的[111] 取向,而且随退火温度或时间的增加,[111]取向程度变得更高.超晶格周期、平均面间距在退火后略有减小,表明多层膜结构在退火后变得更为致密.多层膜界面粗糙度随退火温度或时间的增加而增大,平均相关长度随退火温度或时间的增加而减小,分析认为这是由于Ni₈₀Fe₂₀/Cu界面存在严重的互扩散所导致的.模拟Ni₈₀Fe₂₀/Cu多层膜高角X射线衍射谱,发现在Ni₈₀Fe₂₀/Cu蜀面有非常厚的混合层存在,而且混合层厚度随退火温度或时间的增加而增大.模拟结果还表明,随退火温度或时间的增加,Ni₈₀Fe₂₀层面间距几乎保持不变,Cu层面间距则随退火温度的增加而略有减小. 关键词：     

静电纺丝法制备Bi2Fe4O9及其磁学性能的研究

采用静电纺丝法合成了纤维状的Bi₂Fe₄O₉前驱体,再对前驱体进行热处理得到了棒状的Bi₂Fe₄O₉.通过X射线衍射、扫描电子显微镜及透射电子显微镜表征了合成样品的物相及形貌特征.结果表明合成的样品为Bi₂Fe₄O₉单相,属于正交晶系;退火处理导致纤维状的前驱体转变为棒状的Bi₂Fe₄O₉.紫外-可见吸收光谱表明制备的Bi₂Fe₄O₉对光的吸收范围广,不仅对紫外光具有较强吸收,而且对可见光也有一定的吸收.通过振动样品磁强计测定Bi₂Fe₄O₉磁滞回线研究其磁学特性,相应的矫顽力H_C≈82 Oe（1 Oe=79.5775 A/m）,剥离顺磁信号后的剩磁M_r≈0.25 emu/g,研究发现Bi₂Fe₄O₉样品具有弱铁磁性,并且软磁性能有所提高.     

(Nd1－xGdx)3Fe27.31Ti1.69化合物的结构和磁性

通过X射线衍射和磁性测量等手段研究了(Nd_1-xGd_x)₃Fe_27.31Ti_1.69(0≤x≤0.6)化合物的结构和磁性.X射线衍射测量结果表明Gd替代后并未改变Nd₃(Fe,Ti)₂₉化合物的晶体结构，但引起了晶胞体积收缩.随着Gd含量的增加，化合物的居里温度T_C和室温磁晶各向异性场B_a单调增加，而自旋重取向 关键词： 1-xGd_x)₃Fe_27.31Ti_1.69化合物')" href="#">(Nd_1-xGd_x)₃Fe_27.31Ti_1.69化合物 磁晶各向异性 自旋重取向 磁相图     

溶液旋涂法制备BixY3-xFe5O12薄膜的自旋输运特性

钇铁石榴石(yttrium iron garnet,YIG)的自旋输运特性一直是自旋电子学的研究重点之一.Bi作为YIG最常见的掺杂元素,其薄膜Bi_xY_3-xFe₅O₁₂的磁光特性已经被广泛研究.但Bi³⁺取代Y³⁺对YIG自旋输运的影响规律还没有被系统地研究过.本文利用溶液旋涂法制备了不同掺杂比的Bi_xY_3-xFe₅O₁₂薄膜,并研究Bi掺杂对YIG薄膜形貌结构和自旋输运性能的影响.结果表明Bi掺杂没有改变YIG的晶体结构,掺杂比上升令薄膜的吸收强度增大,带隙减小.XPS表明了Bi³⁺和Bi²⁺的存在.Bi掺杂在自旋输运上的调控体现在Bi_xY_3-xFe₅O₁₂薄膜的磁振子扩散长度相比纯YIG薄膜有所减小.同时研究发现Pt/Bi_x...     

在永磁体强磁场中Mn1.2Fe0.8P1-xSix系列化合物热磁发电研究

研究了处于永磁体强磁场中Mn_1.2Fe_0.8P_1-xSi_x 系列化合物的热磁发电性能, 采用高性能球磨和固相烧结合成方法制备了Mn_1.2Fe_0.8P_1-xSi_x 系列化合物, 并对该系列化合物的物相结构、磁性和热磁发电性能进行了测量. 结果表明: Mn_1.2Fe_0.8P_0.37Si_0.63和Mn_1.2Fe_0.8P_0.35Si_0.65化合物是具有Fe₂P型六角结构的一级相变软磁性材料, 两者居里温度分别为334 K和348 K, 处于工业余热温区. 根据一级相变磁性材料在居里温度磁化强度发生突变这一特性, 研制热磁发电演示装置, 测量了Mn_1.2Fe_0.8P_0.37Si_0.63和Mn_1.2Fe_0.8P_0.35Si_0.65这两种材料铁磁相变产生感应电流大小与线圈匝数、热磁发电材料质量、表面积、表面上温度梯度的关系. 研究结果表明, Mn_1.2Fe_0.8P_1-xSi_x系列化合物具有很好的热磁发电性能, 有望成为热磁发电候选材料.     

Synthetic Co50Pt50/Ru/CoFe hard–soft trilayer in spin valves

The influence of deposition power and seedlayer on the properties of hard magnet Co₅₀Pt₅₀ was studied. Co₅₀Pt₅₀(/Co₉₀Fe₁₀)/Ru/Co₉₀Fe₁₀ trilayer was used as pining/pinned layer in spin valves. The influences of different hard layer, soft layer and free layer on exchange bias, interlayer coupling, and magnetoresistance (MR) ratio were studied. Weak antiferromagnetic interlayer coupling was obtained by adjusting the thickness of hard and soft layers. MR of a spin valve with structure Cr2/CoFe0.5/CoPt4/CoFe0.5/Ru0.8/CoFe2.2/Cu2.05/CoFe2.6/Cu1.1/Ta1 reached 10.68% (unit in nm), which is comparable to those of IrMn-based synthetic spin valves. The increment of the coercivity of the free layer is mainly due to the static magnetic interaction between the hard layer and the free layer.     

Annealing effect of NiO/Co90Fe10 thin films: From bilayer to nanocomposite

Exchange-biased bilayers are widely used in the pinned layers of spintronic devices. While magnetic field annealing (MFA) was routinely engaged during the fabrication of these devices, the annealing effect of NiO/CoFe bilayers is not yet reported. In this paper, the transition from NiO/Co₉₀Fe₁₀ bilayer to nanocomposite single layer was observed through rapid thermal annealing at different temperatures under magnetic field. The as-deposited and low-temperature (<623 K) annealed samples had rock salt (NiO) and face center cubic (Co₉₀Fe₁₀) structures. On the other hand, annealing at 623 K and 673 K resulted in nanocomposite single layers composed of oxides (matrix) and alloys (precipitate), due to grain boundary oxidization and strong interdiffusion in the NiO/CoFe and CoFe/SiO₂ interfaces. The structural transition was accompanied by the reduction of grain sizes, re-ordering of crystallites, incensement of roughness, and reduction of Ni²⁺. When measured at room temperature, the bilayers exhibited soft magnetism with small room-temperature coercivity. The nanocomposite layers exhibited an enhanced coercivity due to the changes in the magnetization reversal mechanism by pinning from the oxides. At 10 K, the increased antiferromagnetic anisotropy in the NiO resulted in enhanced coercivity and exchange bias in the bilayers. The nanocomposites exhibited weaker exchange bias compared with the bilayers due to frustrated interfacial spins. This investigation on how the magnetic properties of exchange-biased bilayers are influenced by magnetic RTA provides insights into controlling the magnetization reversal properties of thin films.     

Planar Hall effect and magnetoresistance in Ni81Fe19 and Co square shaped thin films

Ni₈₁Fe₁₉ and Co thin films have been fabricated and their transport properties have been investigated for potential applications in ultra sensitive magnetic field sensors. The Ni₈₁Fe₁₉ films exhibit an anisotropic magnetoresistance (AMR) of 2.5% with a coercivity 2.5 Oe and the Co films exhibit an AMR of 0.7% with coercivity 11 Oe. Large planar Hall effect magnetoresistance values at room temperature are reported for both cases. An unbalanced Wheatstone bridge model is proposed to describe quantitatively the observed experimental Planar Hall Effect data.     

Demonstration of ultra-high-resolution MFM images using Co90Fe10-coated CNT probes

We demonstrate ultra-high-resolution magnetic force microscopy images of perpendicular magnetic storage media using carbon nanotube probes coated by ferromagnetic Co₉₀Fe₁₀ films (20, 30, 40, and 50 nm). By optimizing ferromagnetic film thickness (effective tip diameter), we obtained best magnetic domain image with an 40 nm-Co₉₀Fe₁₀-coated tip (50 nm tip diameter) about a lateral detect density of 1200 k flux per inch on perpendicular magnetic storage medium, one of the highest resolutions in MFM imaging reported for this material system and structure. The observed dependence of tip dimension on signal contrast and image resolution was successfully explained by a theoretical analysis indicating that the signal contrast, along with the physical probe-tip dimension, should be taken into account to design magnetic probes tips for high-resolution magnetic force microscopy.     

Solvothermal one-step synthesis of MWCNTs/Ni0.5Zn0.5Fe2O4 magnetic composites

A magnetic multi-walled carbon nanotubes-based (MWCNTs-based) composite, MWCNTs/Ni_0.5Zn_0.5Fe₂O₄, was synthesized via a facile solvothermal approach. The composites were characterized by X-ray diffraction analysis, transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), and vibrating sample magnetometry. The results confirmed that MWCNTs and Ni_0.5Zn_0.5Fe₂O₄ coexisted in the composites. The TEM and HRTEM results showed a thick layer of Ni_0.5Zn_0.5Fe₂O₄ was intimately connected to the surface of MWCNTs. The saturation magnetization value of the composites was 45.8 emu/g. Furthermore, the probable synthesis mechanism of the magnetic composites was also investigated based on the experimental results.     

Magnetization modification by superconductivity in Nb/Ni80Fe20/Nb trilayers

We present experimental evidences for magnetization modification by superconductivity in a series of Nb/Ni₈₀Fe₂₀/Nb trilayers. By monitoring the magnetization in a zero field as a function of temperature, we observed an irreversibility in magnetization between the cooling and warming branches just above the superconducting transition temperature T_c. These results suggest that the magnetization of the ferromagnetic Ni₈₀Fe₂₀ layer is reduced by the mutual interactions between the ferromagnet and superconductor. Moreover, this effect diminishes with increasing thickness of the Ni₈₀Fe₂₀ layer, which indicates that the interaction between the superconducting and magnetic layers occurs mainly at the vicinity of the interfaces.     

Giant magneto-impedance effect of magnetron sputtered Ni80Fe20/SiO2/Cu composite wires

In this work, Ni₈₀Fe₂₀/Cu and Ni₈₀Fe₂₀/SiO₂/Cu composite wires of Cu core 100 μm in diameter and coated with a layer of Ni₈₀Fe₂₀ were produced by RF magnetron sputtering. In order to obtain a uniform coating, the wires were spun during sputtering. The influences of the magnetic coating and insulator thickness on the GMI effect of the composite wires were investigated. The results showed that the film thickness has a significant effect on the magnitude and the optimum frequency of the GMI effect. After the addition of an insulator layer, the MI ratio of the composite wires was observed to change with varying thickness of the insulator layer. This observed trend was attributed to the interaction between the conductive layer and the high-permeability magnetic coating.     

Mössbauer effect investigations of Co83Fe17/Au/Co/Au multilayers

[Co₈₃Fe₁₇/Au/Co/Au]_N sputter deposited multilayers displaying a giant magnetoresistance have been investigated. Complementary magnetic measurements were conducted in order to characterize a spin reorientation transition in Co₈₃Fe₁₇ layers sandwiched between Au spacers. The transition from a perpendicular magnetic anisotropy to easy-plane one takes place at the thickness of about 1 nm.     

Saturation magnetic moment at 0°K of PrY2Fe5O12 and NdY2Fe5O12 garnets

The higher saturation magnetic moment of PrY₂Fe₅O₁₂ as compared to NdY₂Fe₅O₁₂ is explained with the aid of magnetic moments obtained from Direc's theory and a definition distinguishing ionicity from valency.