介质阻挡放电低温等离子体脱硝性能研究

进行了介质阻挡放电低温等离子体脱除伴有SO₂的烟气中NO的研究,分别进行了直接等离子体脱硫脱硝和间接等离子体脱硫脱硝实验。在直接等离子体脱硫脱硝中,模拟烟气等混合气直接通入等离子体发生器,在反应器中电离分解NO以及和生成的高能电子、离子和自由基等离子体相互反应而进行脱除NO;间接等离子体脱硫脱硝中,模拟烟气连接在等离子体发生器出口与从反应器中产生出的等离子体发生氧化反应而进行脱除NO。结果表明,无论直接形式还是间接形式,脱硝效率都要比脱硫效率高,间接脱硫脱硝能够大大降低功率输入,节省能耗,具有重要的实际应用价值和意义。氨气的加入,有利于脱除效率的提升。     

脉冲介质阻挡放电条件下NO/O2/N2/Hg0体系反应动力学模拟

利用低温等离子体净化烟气中NO2和Hg是一种极具前景的技术,本文对脉冲介质阻挡放电条件下的NO/O2/N2/Hg0体系建立了反应动力学模型,对高能电子参与N2、O2和H2O电离解速率常数采用碰撞反应截面方法求取,模拟预测了活性自由基元(O、OH)、和Hg0等组分在反应器内随时间的变化规律.模拟结果表明:脉冲介质阻挡放电可以有效地脱除烟气中的NO,并促进单质汞的氧化;脉冲电源特性对脱除效率有明显的影响,电源纳秒级脉冲峰宽时间越长,电源脉冲放电频率越高, NO净化及单质汞的氧化效率越好.     

NaClO/Ca(OH)_2旋转喷雾脱硫脱硝的实验研究

在直径380 mm,高830 mm的工业旋转喷雾吸收塔模型上开展了NaClO/Ca(OH)_2混合液脱除烧结烟气中的SO_2和NO的实验研究,考察了溶液pH,模拟烟气温度,NaClO浓度,SO_2浓度,NO浓度这些操作参数对脱除效率的影响,得出最佳的实验工况为pH=10,T_g=60℃,m_s=6,并在此条件下进行了平行实验,实验结果表明脱硫、脱硝效率可分别达到98%和60%以上。     

微波辐照活性炭床同时脱除SO2和NOx实验研究

论文进行了微波辐照活性炭同时脱硫脱硝实验,研究了烟气中不同组分对脱硫脱硝效率的影响。结果表明,高浓度SO₂对脱硝有轻微抑制。NO对脱硫有一定程度的促进;烟气中O₂的加入对脱硫脱硝均有促进作用;而含湿量的增加首先会使脱硫脱硝效果提高,当含湿量增至9.1%时,脱硫脱硝效率均有下降趋势;烟气中加入CO₂后,脱硫脱硝效率均下降,在氧含量为10%时,脱硫效率下降6%,脱硝效率下降7%。BET测试表明,微波辐照活性炭后其表面积与基炭相比有少量下降。     

电子束辐照烟气脱硫脱氮反应器中的剂量分布的模拟计算

采用Monte-Carlo程序EGSnrcMP对能量为0.8MeV的电子束辐照烟气脱硫脱硝反应器中的剂量分布进行了模拟计算,将计算的结果运用MATLAB数学分析软件进行了数据处理,对能量为0.5MeV的电子束辐照烟气脱硫脱硝反应器中的剂量分布进行了模拟计算,并与文献中实验测量值进行了比较。结果表明:采用EGSnrcMP程序计算所得到的剂量与实验结果吻合。     

铁基磁流化床选择性催化还原烟气脱硝

选择性催化还原(SCR)脱硝是烟气中氮氧化物(NOx)脱除的最有效方法之一,现有SCR系统采用填充床反应器工艺,且催化剂价格较贵.本文以Fe2O3铁基催化剂为床料,以氨为脱硝剂,采用磁流化床进行选择性催化还原脱除氮氧化物实验研究,并对反应前后的床料进行EDAX元素分析和XRD分析.实验结果表明:γ-Fe2O3对加氨SCR脱硝有较强的活性,但随着温度的升高,由于γ-Fe2O3对氨的氧化也表现出较强活性,因而在250°C后,γ-Fe2O3催化剂的脱硝效率会降低;另一方面,磁流化床的良好气固接触与传质特性同时改善了γ-Fe2O3催化剂的上述两个催化活性作用,使其在250°C达到95%的最佳脱硝效率.     

利用链式反应同步氧化烟气中NO和SO2的研究

燃煤烟气中NO和SO2的氧化对于提高其脱除效率和改良脱除产物有重要意义。基于大气化学的研究成果,本文提出了利用链式反应同步氧化烟气中NO和SO2的设想。阐述了该方法的反应机理,数值实验研究了在烟气条件下该链式反应发生的可能性以及反应温度对NO和SO2氧化率的影响,提出了利用低成本的添加剂引发链式反应的方法,并分析了选择添加剂的原则。     

脉冲电晕等离子体反应器能量注入效率

脉冲电晕等离子体处理烟道废气（PPCP法）属于干法脱硫；流程简单；能同时脱硫脱硝；产物是肥料，可实现资源的循环利用；无二次污染；工程造价和运行成本低等优点。但由于脉冲电晕等离子体反应器在短脉冲电压的作用下阻抗变化的复杂性，使得脉冲能量难以有效注入反应器，导致能量注入效率低和脉冲电源关键器件的寿命缩短，因此，研究能量注入效率非常重要。     

燃煤烟气中的CO2和NO对中温烟气脱硫的作用

本文利用实验室规模的循环流化床烟气脱硫实验装置研究了200-400℃范围内的中温干法烟气脱硫过程,并通过对脱硫产物的各种分析,揭示了烟气中CO2及NO对脱硫过程的影响规律及机理。 CO2对脱硫过程有抑制作用,尤其在反应温度大于300℃后,其作用已经不可忽视;NO对脱硫过程有促进作用,但是效果随温度的升高而减小,至350℃以上基本消失,这种促进作用主要是通过生成中间产物Ca(NO3)2而减少CaCO3、CaSO3的生成量来实现的,同时NO的参与也会改善反应的气相扩散条件。     

炭黑非催化还原NO的实验研究

在石英管式炉固定床反应器上研究了程序升温条件下炭黑与NO反应的规律。实验表明:天然气炭黑比其它炭黑具有更高的脱除率、最低的起始反应温度;炭黑的起始反应温度随着NO反应气浓度增大而升高;升温速率越大,NO 的脱除率越大,起始反应温度越低;炭黑质量浓度越大,NO的脱除率越大,起始反应温度越低;反应气中氧存在可以降低炭黑-NO起始反应温度。     

电子束与烟气相互作用机制模拟分析

 电子束在烟气中穿透深度和剂量分布将直接影响废气中硫、氮氧化物的脱除效率。通过理论计算和蒙特卡罗模拟计算得到不同能量电子穿过各种厚度加速器箔窗后能量损失情况；对不同入射能量电子束在烟气中透射深度和轨迹分布进行了模拟计算。结果表明：电子束反应最佳能量为700 keV；利用产生1 m长线状束流的电子加速器进行双面照射，烟道反应室横截面最佳尺寸为1.0 m×3.5 m。     

利用甲醇氧化烟气中NO的实验研究

对利用甲醇氧化烟气中NO的反应开展了系统的实验研究。研究了反应时间、反应温度、甲醇用量比例、烟气中O2、SO2及夹带的固体颗粒对NO氧化率的影响。结果表明,在一定的条件下,甲醇能够氧化烟气中的NO;NO氧化率受反应时间和反应温度的综合影响,随着反应时间的增加,有效反应温度区域向低温方向移动,最大NO氧化率降低;随着甲醇用量比例的增加, NO氧化率增加;O2浓度增加可促进NO氧化;烟气中的SO2对反应有催化作用,可显著提高NO氧化率;烟气中固体颗粒的存在阻碍了自由基反应的进行,显著降低了NO的氧化率。     

Influence of gas flow rate and reactor length on NO removal usingpulsed power

A short duration of 100-ns pulsed power has been used to remove nitric oxide (NO) in a mixture of nitrogen, oxygen, water vapor, and NO, simulating flue gases from a power station. The effects of the gas flow rate, the reactor length, and the pulse repetition rate on the percentage of NO removal and its energy efficiency are reported. The percentage of NO removal at a fixed gas flow rate increased with increasing pulse repetition rate due to the increased energy into the discharge. At a fixed pulse rate, the removal of NO increased with decreasing gas flow rate due to the increased residence time of the gas in the discharge reactor, thus facilitating the creation of increased radicals of O and N which then decreased NO. The energy removal efficiency of NO (in mol/kWh) decreased with increasing gas flow rate and increasing removal ratio of NO. The removal of NO increased with increasing energy density (J/I), input into the discharge at different reactor length     

Formation of hydrophobic coating on PMMA surface using unipolar nanosecond-pulse DBD in atmospheric air

Dielectric barrier discharge (DBD) can modify the material surface and result in complicated physical and chemical reactions to improve the surface hydrophilicity, which is proved to be an effective method for surface modification. Compared with the traditional ac-excitation DBD, the DBD using unipolar pulses can avoid local overheat of microdischarges and can improve discharge efficiency under some conditions. In this paper, DBD excited by repetitive unipolar nanosecond generator was used to improve the hydrophobicity of Plexiglass (PMMA) surface by means of the interaction between air plasma and silicone oil. The output voltage had a rise time of 40 ns and a full width at half maximum of about 70 ns. The surface hydrophobicity of the PMMA, before and after the surface modification, was evaluated via the contact angle measurement under different experimental conditions. The values of the contact angle shown in this paper were the average of eight measured values, and the standard deviations were also calculated. The surface energy including polar and dispersion components was calculated using the measured average contact angles of distilled water and polyethyleneglycol. The results showed that, as the increase of the discharge voltage, the contact angle increased but the surface energy decreased. With the increase of treatment time, the water contact angle of the modified surface increased at the beginning, and it would reach to a maximum at 7.5 min treatment, and then decreased. The effect of pulse frequency on the modification results was different at various treatment times. In addition, the possible physical and chemical reaction among the DBD plasma, silicone oil and the PMMA surface was discussed.     

Back discharge in multipoint-plane geometry in flue gases

The paper presents investigations of back discharge occurring in air and flue gases produced by the process of burning of liquefied petroleum gas or charcoal. The discharge was generated between a multineedle electrode and plate covered with fly ash layer. The aim of this work was to determine the effects of back discharge in multineedle-to-plate electrode configuration on the fly ash layer covering the plate electrode. Level of NO_x and CO emission was also measured. It was found that the chemical composition of flue gas can be changed in the domains where the back discharge occurs, for example, additional amounts of nitrogen oxides (NO and NO₂) are produced and also carbon oxide (CO) was produced at higher discharge current.     

烧结烟气脱硫脱硝用活性炭混合钢渣复合材料的光谱学分析

钢渣是冶金工业中产生的主要固体废弃物,其产量约为每年粗钢产量的15%~20%。由于技术的局限,导致我国钢渣利用率较低,仅为年钢渣产量的10%,同时加之管理制度的不健全,导致钢渣大量露天堆放,对土地资源、地下水源,以及空气质量形成严重影响。固体废弃物再利用是资源可持续发展的重要途径之一,钢渣的主要化学成分为CaO, SiO2, Al2O3, MgO, Fe2O3, MnO, f-CaO等。面对上述问题,利用冶金固体废弃物与活性炭开发一种价格低廉且性能优越的活性炭混合钢渣复合材料,既是冶金固体废弃物的高附加值利用与资源可持续发展的重要途径之一,也是大幅降低改性活性炭生产成本与提高经济效益的重要途径之一。该研究创新性以活性炭与钢渣为研究对象,利用钢渣中含有的金属氧化物对活性炭进行改性处理制备用于烧结烟气脱硫脱硝的活性炭混合钢渣复合材料,通过搭建实验反应装置对活性炭混合钢渣复合材料的脱硫脱硝性能进行测试。利用X射线荧光光谱仪(XRF)对钢渣的化学成分进行测试与分析,比表面积及孔径测定仪(BET)对活性炭混合钢渣复合材料的孔结构进行测试与分析,傅里叶变换红外光谱仪(FTIR)对钢渣的结构组成进行测试与分析,扫描电子显微镜(SEM)对活性炭混合钢渣复合材料的微观结构进行测试与分析,以揭示活性炭与钢渣制备活性炭混合钢渣复合材料的机理,以及活性炭混合钢渣复合材料对烧结烟气脱硫脱硝的机理。结果表明:当钢渣为电炉热泼渣、钢渣与活性炭质量比为2∶4、钢渣与活性炭细度为400目时,活性炭混合钢渣复合材料具有良好的脱硫脱硝性能与合理的经济性,即脱硫效率为100%、脱硝效率为58%。活性炭混合钢渣复合材料具有的多孔结构对SO2和NO进行有作用,钢渣中Fe2O3与MnO2促使活性炭官能团进行催化还原反应提高脱硫脱硝性能,其中吸附作用是主导与前提,催化还原反应是辅助与协同。以期为高附加值的钢渣利用提供新途径,实现钢铁企业以废治废、以废增效的目的。     

������Ͳʽ�����赲�ŵ糡ǿ�͵���ƽ�����ܵķ���

The electric field strength and electron mean kinetic energy in co-axial dielectric barrier discharge (DBD) were estimated based on static electric filed model. Through the comparison of the single dielectric layer DBD with the double dielectric layer DBD, it was found the electric field strength and electron mean kinetic energy in double dielectric layer DBD are greater than that in the single dielectric layer DBD under the same electrode configuration and discharge conditions. The calculation results can successfully applied to explain the toluene degradation efficiency in double dielectric layer DBD is larger than that in the single dielectric layer DBD under the same discharge parameters.     

估算线筒式介质阻挡放电场强和电子平均动能的方法

利用静电场模型对线筒式介质阻挡放电电场强度进行了计算,并对电子平均动能进行了估算。通过对单双介质阻挡放电(DBD)的对比,发现在相同的放电条件下,双介质DBD产生的电场强度和电子平均动能比单介质DBD的要大。这就很好地解释了在相同的放电参数下,甲苯的降解效率在双介质DBD中要比单介质DBD中大。     

Improvement of NOX removal efficiency using short-widthpulsed power

Pulsed power has been used to remove nitric oxide (NO) in a mixture of nitrogen, oxygen, and water vapor simulating the flue gases from a power station stack. The effect of the pulsewidth at a fixed applied voltage on NO removal concentration was studied. The dependence of the energy efficiency of the removal of NO at a fixed applied voltage on the pulsewidth, on the removal ratio of NO and on the discharge current was investigated. This removal energy efficiency increases with decreasing pulsewidth and decreasing removal ratio of NO