PVP-PdCl2-CuCl2/SiO2-PEG600催化芳氯化物水相脱氯研究

PVP(聚乙烯吡咯烷酮)负载双金属催化剂催化芳香氯化物脱氯已有报道[1～3];利用双金属的协同作用,可以大大提高催化剂的脱氯活性和选择性[4]. 但是,这些研究多是在有机相中进行的,催化剂在水相中则会降低甚至失去活性,且难以回收和重复利用. 然而,难溶于水的有毒芳香氯化物,常存在于工业或生活排放的废水中. 由于治理环境的需要,研究芳香氯化物催化水相脱氯,则是极具挑战性的课题. 本文把起相转移作用的聚乙二醇(PEG)键合到硅胶上作为固相载体,制成双负载双金属水相脱氯催化剂PVP-PdCl2-CuCl2/SiO2-PEG600,成功地用于难溶于水的芳香氯化物的水相脱氯. 研究结果表明,这种催化剂对于芳香氯化物有良好的催化脱氯性能,使用中便于分离并能重复利用. 同时,用IR,TEM和XPS等手段对催化剂进行了表征,探讨了催化剂中各组分在催化脱氯中的作用.     

Au-CuO／TiO2催化剂用于CO2中微量H2的脱除

用沉积沉淀法制备了Au-CuO/TiO2催化剂和Au/TiO2催化剂,考察了沉淀温度、沉淀pH、焙烧温度和Cu/Au摩尔比等制备工艺条件对Au-CuO/TiO2催化剂性能的影响,确定了适宜的催化剂制备工艺条件.结果表明,Au-CuO/TiO2催化剂对CO2中微量H2的脱除具有较好的活性和稳定性.还考察了还原和H2S中毒处理先后的顺序对催化剂H2脱除活性的影响.结果表明,Au/TiO2催化剂基本上不受处理顺序的影响,而H2S处理顺序对Au-CuO/TiO2催化剂的性能有较为明显的影响,这说明还原后的Au-CuO/TiO2催化剂形成了Au-Cu合金。     

Preparation, Characterization and Catalytic Properties of S2O2-8/ZrO2 Supported by Tungsten Carbide

A WC-supported S2O2-8/ZrO2(PSZ) catalyst was prepared and characterized by means of XRD, BET, FTIR and XPS. The isomerization of n-pentane over the catalyst was investigated as well. The results show that the skeletal isomerization and the crack of n-pentane proceed simultaneously on WC-supported S2O2-8/ZrO2 catalyst. The addition of tungsten carbide showed a significant enhancement in the activity and stability of the catalyst for n-pentane isomerization. The catalyst showed evidently a better activity than S2O2-8/ZrO2 supported by Pt and WO3. The results can be interpreted by the existence of the tungsten oxycarbide compound(WCxOy) with carbidic, oxide and acidic sites.     

Preparation, Characterization and Catalytic Properties of S2O8^2-／ZrO2 Supported by Tungsten Carbide

A WC-supported S2O8^2-/ZrO2(PSZ) catalyst was prepared and characterized by means of XRD, BET, FTIR and XPS. The isomerization of n-pentane over the catalyst was investigated as well. The results show that the skeletal isomerization and the crack of n-pentane proceed simultaneously on WC-supported S2O8^2-/ZrO2 catalyst. The addition of tungsten carbide showed a significant enhancement in the activity and stability of the catalyst for n-pentane isomerization. The catalyst showed evidently a better activity than S2O8^2-/ZrO2 supported by Pt and WO3. The results can be interpreted by the existence of the tungsten oxycarbide compound(WCxOy) with carbidic, oxide and acidic sites.     

Kinetics of the oxygenation of unsaturated organics with singlet oxygen generated from H2O2 by a heterogeneous molybdenum catalyst

A heterogeneous catalyst containing MoO42- exchanged on layered double hydroxides (Mo-LDHs) is used to produce 1O2 from H2O2, and with this dark 1O2, unsaturated hydrocarbons are oxidized in allylic peroxides. The oxidation kinetics are studied in detail and are compared with the kinetics of oxidation by 1O2, formed from H2O2 by a homogeneous catalyst. A model is proposed for the heterogeneously catalyzed 1O2 generation and peroxide formation. The model divides the reaction suspension in two compartments: (1) the intralamellar and intragranular zones of the LDH catalyst; (2) the bulk solution. The 2-compartment model correctly predicts the oxidant efficiency and peroxide yield for a series of olefin peroxidation reactions. 1O2 is generated at a high rate by the heterogeneous catalyst, but somewhat more 1O2 is lost by quenching with the heterogeneous catalyst than using the homogeneous catalyst. Quenching occurs mainly as a result of collision with the LDH hydroxyl surface, as is evidenced by using LDH supports containing strong 1O2 deactivators such as Ni2+. A total of 15 organic substrates were peroxidized on a preparative scale using the best Mo-LDH catalyst under optimal conditions.     

Palladium-catalyzed N-arylation of 2-aminothiazoles

A method for the Pd-catalyzed coupling of 2-aminothiazole derivatives with aryl bromides and triflates is described. Significantly, for this class of nucleophiles, the coupling exhibits a broad substrate scope and proceeds with a reasonable catalyst loading. Furthermore, an interesting effect of acetic acid as an additive is uncovered that facilitates catalyst activation.     

一种TiO2修饰的Pd/Al2O3选择性加氢用催化剂的研究

 研制了一种用TiO2修饰的Pd/Al2O3(Pd/Al2O3-TiO2)选择性加氢催化剂,并采用N2吸附,XRD,SEM,FT-IR,TPD和TPR等手段对催化剂进行了表征,考察了催化剂的催化性能. 结果表明,Pd/Al2O3-TiO2催化剂具有较小的比表面积; 低的表面酸性,且以弱酸中心为主; TiO2在Al2O3表面呈高度分散,并集中于载体到一定的深度; 用含钛溶液浸渍次数以1次为佳. 载体中TiO2的添加使得PdO更易于被还原. 用这种复合氧化物作载体制备的催化剂表现出更高的加氢活性和选择性,优于单纯以Al2O3作载体的催化剂.     

费托合成中Co/ZrO2/SiO2催化剂的失活行为

 采用等体积分步浸渍法制备了费托合成用Co/ZrO2/SiO2催化剂,并用XRD,TPR和N2-吸附等手段对催化剂进行了表征. 考察了催化剂在费托反应过程中的结构变化和失活行为. 结果表明,反应过程中硅酸钴物种的生成是催化剂失活的主要原因,且硅酸钴的生成与产物水的分压有关; 晶粒长大也可能是催化剂失活的原因之一.     

用于苯选择加氢制环己烯的非晶态合金Ru-La-B/ZrO2催化剂的失活与再生

 研究了在中试装置上经长期运转后的非晶态合金Ru-La-B/ZrO2催化剂的失活原因与再生方法. 结果表明: 催化剂失活不是由微孔堵塞、比表面积减小、晶粒长大或催化剂中毒而引起的,而是由于在长期运转过程中催化剂吸附了反应浆液中的Zn2+ 和反应器壁引入的Fe2+ , 通过酸洗的方法可以使催化剂的活性和选择性基本恢复.     

SO4−2/SnO2–catalyzed cyclocondensation for the synthesis of fully functionalized pyridines

An efficient and promising synthetic approach to assemble skeletons of multifunctionalized pyridine derivatives in presence of recyclable heterogeneous sulfated tin oxide (STO) catalyst has been evolved. The STO catalyst was used as a promoter for the cyclocondensation process in ethanol at 70°C. Overall performance of this catalyst was attributed to the cooperative contribution of its Lewis and Brønsted-Lowry acidic sites. Nanosized STO catalyst was synthesized by using sol-gel process and characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), ¹H-NMR, and scanning electron microscopy (SEM). This catalyst tolerates most of the substrates, and protocol shows precious capabilities consist of high yields, operational simplicity, less reaction time, and eco-friendly conditions. The newly synthesized heterogeneous catalyst was easily separated and reused. All the reactions are carried out for subsequent cycles without significant loss of catalytic activity and with good proficiency.     

高岭土负载SO42-/ZrO2-TiO2催化剂的制备及其在缩酮合成中的应用

以经H2SO4处理焙烧的高岭土为载体,制备了以其负载的SO2-4/ZrO2-TiO2固体酸催化剂。 用FT-IR、XRD和NH3-TPD等测试技术表征了催化剂的微观结构及酸强度,考察了对环己酮乙二醇缩酮反应的催化活性及稳定性。 结果表明,酸化处理使高岭土表面酸量增加,但酸强度变化不大,而其负载SO2-4/ZrO2-TiO2后,经500 ℃焙烧3 h其酸量及酸强度显著升高。 环己酮用量为0.2 mol、乙二醇0.24 mol、催化剂1.2 g、带水剂环己烷15 mL,回流反应70 min后,缩酮收率可达96.8%,催化剂重复使用5次收率保持在90%以上。     

Catalytic Performance of Amorphous Ti/SiO2 in the Gas-Phase Epoxidation of Propylene with H2O2

The epoxidation of propylene with dilute H₂O₂ aqueous solution over titanium silicalite-1 (TS-1) zeolite catalyst is a green chemical reaction for propylene oxide (PO) production. Carrying out the reaction in gas-phase can get rid of problems caused by using methanol solvent. This paper reports an attempt of using non-zeolite catalyst for the gas-phase epoxidation. Amorphous Ti/SiO₂, obtained by grafting amorphous SiO₂ with TCl₄ in ethanol solvent in a chemical liquid-phase deposition (CLD) process, has been used as the catalyst. Results show that the CLD Ti/SiO₂ with appropriate Si/Ti molar ratio is an active catalyst for gas-phase epoxidation, achieving 9.8 % propylene conversion and 66.9 % PO selectivity with 40.3 % H₂O₂ utilization, which indicates that this amorphous Ti/SiO₂ catalyst deserves extensive studies in the future.     

Ethylene polymerization with porous polystyrene spheres supported Cp2ZrCl2 catalyst

A catalyst with porous polystyrene beads supported Cp₂ZrCl₂ was prepared and tested for ethylene polymerization with methylaluminoxane as a cocatalyst. By comparison, the porous supported catalyst maintained higher activity and produced polyethylene with better morphology than its corresponding solid supported catalyst. The differences between activities of the catalysts and morphologies of the products were reasonably explained by the fragmentation processes of support as frequently observed with the inorganic supported Ziegler–Natta catalysts. Investigation into the distribution of polystyrene in the polyethylene revealed the fact that the porous polystyrene supported catalyst had undergone fragmentation during polymerization. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3313–3319, 2003     

Pt含量及活化温度对固体超强酸催化剂异构化性能的影响

本文制备了固体超强酸Pt- S2O82-/ZrO2-Al2O3催化剂,采用XRD、TPR、TG-DTA 、FT-IR等表征手段对催化剂进行了表征,并在高压微反－色谱联合装置上,考察了Pt质量分数和活化温度对催化剂正戊烷异构化性能的影响. 结果表明,Pt能使催化剂的还原温度降低;增强载体表面氢气的溢流效应,提高酸强度;Pt质量分数0.10%、活化温度300℃的催化剂异构化活性最高,在反应温度220℃、压力2.0MPa、氢烃摩尔比4:1、质量空速1.0h-1时,异戊烷产率达62.3%. 在100h内异戊烷收率可稳定在55%左右,选择性在98.0％以上.     

CeO2/TiO2 Monolith Catalyst for the Selective Catalytic Reduction of NOx with NH3: Influence of H2O and SO2

The influences of H₂O and SO₂ on CeO₂/TiO₂ monolith catalyst for the selective catalytic reduction(SCR) of NO_x with NH₃ were investigated. In the absence of SO₂, H₂O inhibited the SCR activity, which might be ascribed to the competitive adsorption of H₂O and reactants such as NH₃ and/or NO_x. SO₂ could promote the SCR activity of CeO₂/TiO₂ monolith catalyst in the absence of H₂O, while in the presence of H₂O it speeded the deactivation. During the SCR reaction in SO₂-containing gases, Ce(III) sulfate species formed on the catalyst surface, resulting in the enhancement of Brønsted acidity. This played a significant role in the enhanced SCR activity. However, in the presence of both H₂O and SO₂, a large amount of ammonium-sulfate salts formed on the catalyst surface, which resulted in the blocking of catalyst pores and deactivated the catalyst. In addition, the NO_x conversion was more sensitive to gas hourly space velocity in the presence of H₂O than in the absence of H₂O. The relatively high space velocity would result in a higher formation rate of ammonium-sulfate salts on per unit catalyst in the presence of H₂O and SO₂, which caused obvious deactivation of Ce/TiO₂ monolith catalyst.     

柠檬酸对Ni2P/TiO2-Al2O3催化剂加氢脱硫性能的影响

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,以柠檬酸(CA)为络合剂采用浸渍法制备了Ni2P负载的TiO2-Al2O3复合载体催化剂,并用X射线衍射(XRD)、N2吸附比表面积测定、H2程序升温氢还原(H2-TPR)、程序升温氧化(TPO)、X射线光电子能谱(XPS)技术对催化剂的结构和性质进行了表征,考察了CA/Ni摩尔比对在Ni2P/TiO2-Al2O3催化剂上进行的二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响.结果表明:适量的CA可以丰富催化剂的孔道,提高催化剂的比表面积.当n(CA)/n(Ni)=2:1时,催化剂的比表面积达到126.75m2·g-1,与不加CA时相比,提高了57.05m2·g-1.调节n(CA)/n(Ni)能够改善活性相的分布,改变活性相的种类;引入CA使Ni和P前驱体的还原温度明显降低,促进活性相Ni2P的生成,一定程度上能够抑制催化剂表面炭的形成和沉积,提高其稳定性.n(CA)/n(Ni)=2:1时,催化剂具有最好的加氢脱硫活性,在360°C,3.0MPa,氢油比为500(V/V),液时体积空速为2.0h-1的条件下,二苯并噻吩转化率为99.5%,可将模拟油中硫含量由2%(w)降低到0.01%(w).     

Cr2O3在铜基甲醇合成催化剂中的作用

研究了三组份Cu－ZnO－Al_2O_3催化剂添加Cr_2O_3后．铬在催化剂中的存在形式，助催作用本质及其与甲醇含成催化活性的关联。结果表明：在ZnO－Cr_2O_3催化剂中，铬以Cr~(3 )和ZnCr_2O_4形式存在于ZnO晶格中，Cu-ZnO-Al_2O_3-Cr_2O_3催化剂的催化活性与CR~(3 )在ZnO晶格中诱导出来的正一价缺位和催化剂的其它顺磁性物种的ESR强度能很好地关联，在活性测试中，以含1％Cr（原子比）的Cu-ZnO-Al_2O_3-Cr_2O_3的催化活性最高。     

SnCl2/nano SiO2：A green and reusable heterogeneous catalyst for the synthesis of polyfunctionalized 4H-pyrans

A highly efficient and general method for the synthesis of polyfunctionalized 4H-pyrans is established through a one-pot multicomponent cyclocondensation of aromatic aldehydes with CH acids, malononitrile and ethyl acetoacetate using nano silica supported tin (Ⅱ) chloride as a catalyst. In this method SnCl2/nano SiO2 was used as green and reusable catalyst. Excellent yields, short reaction times, simple workup, and inexpensiveness and commercially availability of the catalyst are the advantages of this method.     

由Mg(nBu)2制备的MgCl2载体催化剂的烯烃聚合动力学

讨论了催化剂ＣＤ，ＣＭ和ＣＤ－Ａ的乙烯和丙烯聚合动力学曲线，只有催化剂ＣＤ在丙烯聚合时加入外给电子体其动力学曲线为上升－衰减型，其它均为衰减型，催化剂ＣＤ丙烯聚合活性高于催化剂ＣＭ。丙烯聚合时加入外给电子体使总活性中心浓度降低，但等规中心浓度反应增加。同种载体制备的催化剂ＣＤ和ＣＤ－Ａ载钛过程中加入内给电子体，可使其聚合活性增加，在一定范围内，随Ａｌ／Ｔｉ增加，在一定范围内，随Ａｌ／Ｔｉ增加，催化     

Vanadium-based Ziegler-Natta catalyst supported on MgCl2(THF)2 for ethylene polymerization

A supported magnesium-vanadium-aluminium catalyst was prepared by depositing –with the use of a milling technique–VOCl₃ on the MgCl₂(THF)₂ support and subsequent activation with diethylaluminium chloride. Catalytic activity of the obtained system for ethylene polymerization was evaluated as a function of Mg/V and Al/V ratios as well as catalyst ageing time and polymerization temperature. High concentrations of THF in the catalytic system and considerable excess of an organoaluminium co-catalyst were found to have no deactivating action on vanadium active sites. The catalyst obtained is stable and its activity for ethylene polymerization is high. It yields polyethylene with higher molecular weight and higher melting point than offered by the materials produced with the use of a corresponding unsupported vanadium catalyst or a titanium-based system on the same magnesium support. Kinetic investigations confirmed stability of this catalyst irrespective of its concentration in the polymerization medium or of monomer concentration. Moreover, analysis of the kinetic findings revealed that over 80% of vanadium employed forms active polymerization sites.