高质量CdSe量子点的水相制备与表征

以巯基丁二酸为稳定剂, 亚硒酸钠为硒源, 制备了高质量水溶性CdSe量子点. 研究了反应时间、 镉与硒的摩尔比及镉与巯基丁二酸的摩尔比等实验条件对CdSe量子点光谱性能的影响. 分别用紫外-可见光谱、 荧光光谱、 X射线粉末衍射和透射电子显微镜等对量子点进行表征. 结果表明, 采用这种方法制得的CdSe量子点为立方晶型, 量子点的荧光发射峰在518～562 nm范围内连续可调, 并且发射峰的半峰宽始终保持在35 nm左右, 荧光量子产率可达21%.     

水溶性CdTe量子点的合成及影响因素研究

本文以巯基乙酸(TGA)为稳定剂,在水相中合成了高荧光CdTe量子点.其荧光发射波长在507 ～ 628nm范围内可调,最窄半峰宽37 nm,粒径约3.4nm,量子产率达42.1％.本实验在固定前躯体配比不变的情况下,考察了前躯体中镉离子的浓度、pH及回流时间对CdTe生长的影响.并用透射电子显微镜(TEM),荧光分光光度计(FS),X射线衍射仪(XRD)等手段对制备的量子点进行了表征.结果表明:CdTe量子点的尺寸随回流时间而增长;反应的pH对量子点的荧光强度有显著影响;镉离子的浓度越大,量子点的生长速度越快,荧光强度却随之降低.     

一锅合成绿色到近红外发射的CdTe量子点

以3-巯基丙酸(MPA)为稳定剂,采用水相合成法制备了从绿色到近红外发射的CdTe量子点。系统研究了反应液pH值、镉和碲的物质的量之比及镉和3-巯基丙酸的物质的量之比等实验条件对CdTe量子点体系的发射波长和荧光量子产率的影响。在pH值为10.5,且nCd2+∶nTe2-∶nMPA=1∶0.05∶1.1的条件下,回流0.5 h,CdTe量子点体系在569 nm波长处的荧光量子产率达到30.8%;在7 h的回流时间内,制备的量子点的波长覆盖范围为525～730 nm。分别用X射线粉末衍射、透射电镜和红外光谱对CdTe量子点的晶体结构、形貌及表面基团进行表征。     

一种新型铜离子荧光探针——CdTe量子点

探讨了髙量子产率CdTe量子点作为铜离子探针的可能性,发现铜离子对碲化镉量子点的荧光有猝灭效应,且量子点溶液的荧光强度与铜离子浓度成良好的负相关线性关系.由于CdTe量子点比CdS具有更为优良的光学性质和稳定性,有望成为一种新型纳米离子探针.     

ZnS-AgInS_2量子点的制备及修饰

通过热裂解法以油胺为配体制备了ZnS-AgInS2量子点。产物荧光性质好,通过改变Zn、Ag、In元素的比例可发射从红色到蓝色的荧光,荧光量子产率可以达到15%;其晶体结构和分散性好,粒径均匀(约为4nm)。分别采用两种不同的配体取代法将油溶性ZnS-AgInS2量子点修饰为水相性,发现羧甲基聚乙二醇硫醇(CM-PEG-SH)和巯基丙酸共修饰得到的产物比经巯基乙酸修饰得到的产物具有更好的荧光性质和稳定性,前者的荧光量子产率可达到10%,且连续2个月的检测结果表明其荧光强度随着放置时间的延长而增强。考察了常见阳离子对CM-PEG-SH和巯基丙酸共修饰产物荧光性质的影响,初步探讨了其影响机理。     

川木香水热法一步合成荧光碳量子点及光学性能研究

以中药材川木香原药为碳源，采用水热法一步合成了荧光碳量子点。通过水热法实验条件优化，获得制备荧光碳量子点的最佳实验参数，通过透射电镜(TEM)对荧光碳量子点进行形貌表征，通过X射线光电子能谱分仪(XPS)对荧光碳量子点进行元素组成分析，通过荧光光谱和紫外-可见吸收光谱对荧光碳量子点进行了光学性能研究。结果表明：川木香用量1.00 g,水热反应温度180℃,水热反应时间2.0 h时，制备得到的荧光碳量子点光学性能最佳。荧光碳量子点平均粒径为5 nm,主要含有C元素和O元素，最大激发波长为360 nm,对应的发射波长为420 nm,特征吸收峰为280 nm,量子产率为12.9%。     

硫脲修饰Cd掺杂ZnO水溶性量子点的制备及表征

在非水稀溶液中以聚乙烯吡咯烷酮K-30为稳定剂,硫脲为表面修饰剂,制备Cd掺杂ZnO水溶性量子点荧光体;同时研究了基质的优化及硫脲含量对ZnO量子点发光性能的影响,Eu和Li的共掺杂对ZnO:Cd量子点发光性能的影响.采用紫外光谱、荧光发射光谱、红外光谱和透射电镜、XRD对样品进行表征.结果表明:经Cd优化基质后、Eu和Li的共掺杂使量子点荧光强度明显增强;硫脲修饰后纳米颗粒分布更加均匀、晶粒更小、荧光光谱蓝移、量子点产率增加;该样品XRD衍射峰是馒头峰.属于无定形态;红外光谱图中因硫脲引起的NH2和C-NH2伸缩振动吸收峰分别为3189.0,1088.2 cm-1,硫脲修饰的最佳浓度大约为32 mg/mL.该量子点制备方法简单易行,具有较好的稳定性及高荧光量子效率,为进一步应用于生物标记奠定基础.     

柠檬酸稳定的水溶性CdSe和CdSe/CdS量子点的荧光特性

用柠檬酸(citrate)作为稳定剂合成了尺寸分布集中、荧光性质良好的水溶性CdSe量子点。通过调节合成温度可以调控CdSe量子点的尺寸及相应的最大荧光发射波长。当温度由20 ℃增加到95 ℃时,合成的CdSe量子点的平均尺寸由2.0 nm增加到3.2 nm,相应的荧光发射峰由500 nm红移到570 nm,展现出明显的量子尺寸效应。进一步制备了CdSe/CdS核壳量子点,其荧光量子产率比CdSe增加了5～10倍。系统地研究了S/Se物质的量的比对CdSe/CdS量子点荧光特性的影响,通过XPS证实了CdSe/CdS量子点中CdS壳层的存在。利用红外光谱和核磁共振波谱表征了柠檬酸分子中的羧基和羟基氧原子与CdSe量子点表面的Cd离子的配位作用,进而揭示了柠檬酸分子对水溶性CdSe量子点溶液的稳定作用。     

硫脲修饰ZnSe:Cu量子点的水相合成及荧光特性

以3-巯基丙酸为稳定剂在水相中合成了Cu掺杂的ZnSe量子点(QDs), 并利用硫脲(CH₄N₂S)对其进行表面修饰, 制备出核壳结构的ZnSe:Cu/ZnS 量子点. 制得的量子点呈闪锌矿结构, 尺寸约为5 nm, 有较好的分散性, 其荧光发射峰在460 nm左右. 经CH₄N₂S修饰后, 量子点表面形成了宽禁带的ZnS包覆层, 将电子和空穴限域在了ZnSe:Cu 核内, 减少了表面发生非辐射复合的载流子, 显著提高了量子点的荧光强度. 与Na₂S、硫代乙酰胺(TAA)等常用硫源相比, 以CH₄N₂S为硫源制得的ZnSe:Cu/ZnS 量子点壳层厚度可控, 表面钝化效果更好, 显示出更佳的荧光效率和稳定性. ZnSe:Cu/ZnS 量子点经过紫外线照射后消除了表面的悬空键, 进一步提高了其量子产率, 最终获到了具有较好荧光性质的ZnSe:Cu/ZnS量子点.     

3-巯基异丁酸衍生物对碲化镉量子点水相合成的影响

为探索适宜制备粒径分布窄、荧光量子产率高、发光区域在红光至近红外光区段的量子点的巯基酸的条件, 我们研究了三类3-巯基异丁酸(MIBA)衍生物在以亚碲酸钠为碲源的水相法水热制备CdTe量子点中的影响. 这三类衍生物包括设计合成的主链亲水性衍生物3-巯基异丁酰甘氨酸(MIBGly)、3-巯基异丁酰-3-氨基丙酸(MIBAPA)和3-巯基异丁酰天冬氨酸(MIBAsp), 支链亲水性衍生物N-乙酰基半胱氨酸(ACys)和支链疏水性衍生物3-巯基-2-甲基丁酸(MMBA)和3-巯基-2,2-二甲基丙酸(MDMPA). 以这三类MIBA 衍生物为修饰剂时,CdTe量子点均能够保持MIBA体系较窄的荧光半峰宽. 采用亲水性的MIBA衍生物(MIBGly、MIBAPA、MIBAsp和ACys)比采用疏水性的MIBA衍生物(MMBA和MDMPA)更有利于制备发射波长较长的量子点. 采用支链亲水性的MIBA衍生物((ACys)比采用主链亲水性的MIBA衍生物(MIBGly、MIBAPA和MIBAsp)更容易获得高荧光量子产率的量子点.     

Luminescent properties of water-soluble denatured bovine serum albumin-coated CdTe quantum dots

Chemically reduced bovine serum albumin (BSA) has been used to modify the surface of water-soluble CdTe quantum dots (QDs). It is demonstrated that the denatured BSA (dBSA) can be conjugated to the surface of CdTe QDs and thereby efficiently improve the chemical stability and the photoluminescence quantum yield (PL QY) of the QDs. It is inferred that a shell-like complex structure CdTe(x)(dBSA)(1-x) will form on the surface of the CdTe "core", resulting in the enhancement of PL intensity and the blue shift of the PL peak. This study of the effects of pH and dBSA concentration on optical properties of dBSA-coated QDs suggests that, at pH 6-9, the solution of dBSA-coated CdTe QDs can keep substantial stability and fluorescent brightness, whereas further increase of pH value leads to a dramatic decrease in PL QY and chemical stability. On the other hand, too high or too low initial dBSA concentration in the QD solution results in a decrease of PL QY for dBSA-coated CdTe QDs. This study provides a new approach of preparing stable water-soluble QDs with high PL QY and controllable luminescent colors for biological labeling applications.     

Microwave-assisted Synthesis of CdTe Quantum Dots Using 3-Mercaptopropionic Acid as Both a Reducing Agent and a Stabilizer

In this paper, a facile synthetic approach to prepare CdTe quantum dots(QDs) with high luminescence via a one-pot microwave irradiation reaction route using 3-mercaptopropionic acid(MPA) as both a sodium tellurite reducer and a capping molecule was described, and the mechanism of the formation of CdTe QDs was elucidated. In this approach, CdTe QDs with six different emission wavelengths of 553, 567, 577, 595, 608 and 615 nm were obtained via changing the refluxing time and the quantum yields(QY) of these QDs were 40.6%, 55.3%, 63.6%, 43.4%, 37.4% and 29.7%, respectively. The characterization results of X-ray powder diffraction(XRD) and transmission electron microscopy(TEM) indicate that the obtained QDs have a pure cubic zinc blended structure with a spherical shape. No toxic gases were released during the preparation process, indicating that the method is relatively fast, cheap and environmentally friendly.     

表面修饰CdTe量子点的合成及其光学特性

在水相中合成高发光性能的CdTe量子点,研究以巯基乙酸(TGA)为稳定剂对CdTe表面进行修饰,制备在水中分散性良好的纳米晶,通过对CdTe量子点合成反应条件的摸索,掌握了其合成的反应规律.同时用紫外分光光度计、荧光分光光度计和透射电子显微镜对其进行了表征.结果表明,回流时间、n(Cd²⁺):n(HTe^-)、反应物浓度、TGA用量、反应体系pH值,对纳米晶的光学性质具有显著影响.回流2 h制得的CdTe纳米粒子直径约为5 nm,其发射峰窄且对称,表现出良好稳定的光学性质.     

水热法合成巯基乙胺稳定的CdTe量子点

提出了一种以水热法合成巯基乙胺稳定的CdTe量子点的简单制备路线. 在优化的反应条件下, 产物的荧光量子效率最高达到19.7%, 接近已报道的其它方法的2倍. 考察了反应条件对产物的荧光性能的影响及产物在不同pH溶液中的稳定性.     

Hydrothermal synthesis of highly luminescent CdTe quantum dots by adjusting precursors’ concentration and their conjunction with BSA as biological fluorescent probes

A study on hydrothermal synthesis of CdTe quantum dots, highly luminescent nanocrystals at a relatively lower temperature, via changing the concentration of the CdTe precursors, is described. The full width at half maximum ranged from 40 to 80 nm and quantum yield (QY) was detected to be 27.4% at room temperature. The as-prepared CdTe QDs were labeled with BSA for fluorescence probes without pretreatment. Conjunction experimental results suggested that the as-prepared CdTe QDs are suitable for the application of biotechnology.     

水溶性的高荧光CdTe/CdSeⅡ型核壳量子点的合成与表征

用L-半胱氨酸(L-cysteine)作为稳定剂,以制备的CdTe量子点为核模板,水相合成了具有近红外发光的Ⅱ型核壳CdTe/CdSe半导体量子点。实验考察了合成温度,核模板的尺寸和组分比等因素对合成高质量的CdTe/CdSe量子点的影响。用紫外-可见吸收和荧光光谱研究了合成的量子点的光学性质。在优化的合成条件下,荧光发射光谱在586～753nm范围连续可调,荧光量子产率高达68%;通过X-射线衍射(XRD),X射线光电子能谱(XPS)和透射电镜(TEM)对合成的Ⅱ型核壳CdTe/CdSe量子点进行了结构和形貌表征。     

Study on the interaction of CdTe quantum dots with coumaric acid and caffeic acid based on fluorescence reversible tune

This paper describes the synthesis of CdTe quantum dots (QDs) together capped by glutathione and thioglycolic acid (GSH and TGA) in aqueous solution. The narrow photoluminescence (fwhm ≤ 40 nm) CdTe QDs, whose emission spans most of the visible spectrum from green through red, has a quantum yield (QY) of 68% at room temperature. GSH/TGA-CdTe QDs are characterized by various experimental techniques such as optical absorption, photoluminescence and AFM measurements. Coumaric acid and caffeic acid is able to quench the fluorescence of GSH/TGA-CdTe QDs, and the fluorescence intensity is linearly proportional to the concentration of quenchers. The addition of bovine serum albumin (BSA) restores the fluorescence intensity of GSH/TGA-CdTe QDs-coumaric acid system and GSH/TGA-CdTe QDs-caffeic acid system. The fluorescence recovery was due to the interaction of BSA with coumaric acid and caffeic acid, leading to the freeing of the GSH/TGA-CdTe QDs. The fluorescence quenching mechanism of GSH/TGA-CdTe QDs was discussed. The binding constant and thermodynamics parameters of BSA-coumaric acid and BSA-caffeic acid during the binding process were calculated in the paper.     

Effect of CdS Interlayer on Properties of CdTe Based Quantum Dots

Highly luminescent thioglycolic acid-capped CdTe-based core/shell quantum dots (QDs) were synthesized through encapsulating CdTe QDs in various inorganic shells including CdS, ZnS and CdZnS. CdTe/CdS core/shell QDs exhibited a significant redshift of emission peaks (a maximum emission peak of 652 nm for the core/shell QDs and 575 nm for CdTe cores) with increasing shell thickness. In contrast, the redshift of photoluminescence (PL) peak wavelength of CdTe/ZnS QDs was less than 15 nm. The PL peak wavelengths of the core/shell QDs depended strongly on core size and shell thickness. The PL quantum yields (QYs) of the CdTe/CdS core/shell QDs are up to 67 % while that of CdTe/ZnS core/shell QDs is 45 %. A composite CdZnS shell made CdTe cores a high PL QY up to 51 % and broadly adjusted PL spectra (a maximum PL peak wavelength of 664 nm). The epitaxial growth of the shell was confirmed by X-ray powder diffraction analysis and luminescence decay experiments. Because of high PL QYs, tunable PL spectra, and low toxicity from a ZnS surface layer, CdTe/CdZnS core/shell QDs will be great potential for bioapplications.     

颜色可调的高荧光CdTe量子点的水相合成

以亚碲酸钠为碲源,硼氢化钠为还原剂,一步合成了巯基丁二酸(MSA)稳定的CdTe量子点.研究了反应液pH值、镉与碲的摩尔比及镉与巯基丁二酸的摩尔比等实验条件对CdTe量子点体系荧光量子产率的影响,并用荧光光谱、X射线粉末衍射及透射电子显微镜等对其进行了表征.结果表明,CdTe量子点具有闪锌矿结构,形貌呈球状;在pH=1...