草酸淀粉酯制备及其性能研究

本文以草酸和玉米淀粉为原料,通过改变原料的摩尔比反应制备了不同取代度(0.1到0.9)的草酸淀粉酯,采用滴定法测定产物的取代度,利用红外光谱和核磁共振表征产物(取代度为0.41)的化学结构,产物中含有羰基的结果表明成功制备了草酸淀粉酯.详细考察了草酸淀粉酯的物理化学性质,利用粘度测定、热重分析、广角X衍射(WXRD)以及湿度吸收等研究不同取代度的草酸淀粉酯的分子量、热稳定性,结晶形态以及吸水性能.结果说明,与玉米淀粉相比,草酸淀粉酯的吸水率随着取代度的提高而增加,其分子量、热稳定性以及结晶性能则呈下降趋势.     

醋酸酯淀粉高取代度的测定

淀粉的乙酰化改性是扩大其应用的一个重要手段。测定醋酸酯淀粉取代度 (DegreeofSubstitution ,简称DS)的方法通常有酸碱滴定法、紫外法、核磁共振法及衰减全反射法[1 ] 等 ,后 3种方法需建立标准曲线 ,要求有一系列取代度的样品 ,实验操作较困难。所以实验室更多采用酸碱滴定法。实验室多采用乙醇为溶剂进行醋酸酯淀粉高取代度的测定[1～3] 。这种方法的缺点是皂化时间需 48～ 72h ,并且高取代度醋酸酯淀粉的溶解性不理想。本文对酸碱滴定法测定醋酸酯淀粉高取代度溶剂选择进行了探讨 ,以期建立一种快速、准确地测定醋酸酯淀粉高取代度的…     

“一锅法”均相合成热塑性纤维素丙酸酯接枝聚乳酸共聚物

纤维素重复单元的羟基上引入足够数量的柔性分子链,有可能在破坏纤维素分子链间氢键的同时起到内增塑作用,从而赋予纤维素熔融流动性.由纤维素酯化反应得到的一些短链取代的纤维素酯[如纤维素醋酸酯(CA)、纤维素丙酸酯(CP)等]具有热塑性,但需要在外加大量增塑剂条件下才能熔融加工[1].接枝共聚合是改变纤维素物理化学性质的另一种有效方法[2～4]。     

高取代度玉米醋酸酯淀粉的制备与表征

高取代度玉米醋酸酯淀粉的制备与表征;取代度;醋酸酯淀粉;玻璃化转变温度;结晶度     

高取代度魔芋葡甘聚糖醋酸酯的制备及其热塑性和流变性研究

以魔芋葡甘聚糖(KGM)为原料,浓硫酸为催化剂,乙酸酐为改性剂,制备了KGM醋酸酯.研究了反应条件对KGM醋酸酯取代度(DS)的影响,KGM醋酸酯制备的最佳反应条件是乙醇∶水量比5∶5,反应时间2h,反应温度75℃,催化剂浓硫酸的浓度0.1mol/L,KGM与乙酸酐的量比5∶40(g/mL),取代度高达2.93,其分子量与KGM相比,则明显降低.运用傅立叶红外光谱仪(FTIR)、X射线衍射仪(XRD)、扫描电镜(SEM)、热重分析仪(TGA)、示差扫描量热仪(DSC)和旋转流变仪对KGM和高取代度KGM醋酸酯进行了表征.结果表明,KGM醋酸酯的羰基(CO)特征吸收峰较KGM明显增强,其表观形貌大部分为疏松絮状,KGM及其醋酸酯均为非晶态结构.与KGM相比,KGM醋酸酯的热稳定性下降,分解温度(Td)由KGM的261.10℃降低至KGM醋酸酯的204.56℃,KGM醋酸酯出现了明显的玻璃化转变,其玻璃化转变温度(Tg)为128.49℃.KGM醋酸酯是典型的黏弹性材料,其弹性比率占21.27%,其剪切黏度η对温度变化非常敏感,可通过温度的改变来调节KGM醋酸酯的加工流动性.KGM醋酸酯具有较好的热塑性.     

干法制备阳离子淀粉(I):反应效率的研究

在碱催化剂BZ-1存在下,以N-(2,3-环氧丙基)三甲基氯化铵(GTA)为阳离子化试剂,干法制备了高取代度季铵型阳离子淀粉.考察了碱催化剂BZ-1、水含量、反应温度和反应时间对取代度和反应效率的影响.当淀粉用量为5.5g,GTA用量为3g时,最佳反应条件为:碱催化剂BZ-1 0.8g、反应温度60℃、反应时间4h、反应体系含水量24%,取代度可达0.56,反应效率为88%.     

药物控释载体醋酸酯淀粉的消化性能研究

采用生物体外(in-vitro)消化模型模拟人体消化道环境，对不同取代度的醋酸酯化木薯淀粉的消化速率进行了研究；用微生物酶对醋酸酯化木薯淀粉进行生物降解并测定各个样品的抗消化淀粉含量。结果表明醋酸酯化会增大淀粉颗粒的消化速率，但随取代度的提高消化速率呈下降趋势。同样随取代度的提高，醋酸酯化也会降低淀粉糊的消化速率。醋酸酯淀粉卡抗消化淀粉含量低于原淀粉，且取代度越高含量越低。醋酸酯化会破坏和抑制淀粉中抗消化淀粉的形成。     

高直链淀粉乙酸酯的均相合成及其静电纺丝

离子液体1-烯丙基-3-甲基咪唑氯盐(amimCl)可以有效地溶解高直链淀粉.以amimCl为均相反应介质,在无外加催化剂的存在下一步合成了取代度范围较宽的高直链淀粉乙酸酯.考察了反应时间和酰化试剂用量对酰化程度的影响.不同取代度的酰化淀粉在水、丙酮和DMAc等溶剂中表现出不同的溶解性.进一步对高直链淀粉乙酸酯溶液进行静电纺丝,制备出了由直径在数十至数百纳米、表面光滑、连续的纳米纤维组成的超细纤维多孔膜.     

干法制备阳离子淀粉（Ⅰ）：反应效率的研究

在碱催化剂BZ-1存在下,以N-（2,3-环氧丙基）三甲基氯化铵（GTA）为阳离子化试剂,干法制备了高取代度季铵型阳离子淀粉。考察了碱催化剂BZ-1、水含量、反应温度和反应时间对取代度和反应效率的影响。当淀粉用量为5.5g,GTA用量为3g时,最佳反应条件为：碱催化剂BZ-10.8g、反应温度60℃、反应时间4h、反应体系含水量24%,取代度可达0.56,反应效率为88%.     

乙酰化淀粉/DL-丙交酯接枝共聚物的合成及降解性能研究

用醋酸乙烯酯和玉米淀粉反应制备出了不同取代度乙酰化淀粉，再用乙酰化淀粉同DL－丙交酯接枝共聚合成乙酰化淀粉／DL－丙交酯接枝共聚物。研究了原料配比，淀粉取代度对接枝反应单体转化率（C％），接枝率（G％）接枝效率（GE％）和接枝支链数均分子量（Mn)的影响，结果表明在给定的试验条件下接枝共聚反应的C％，G％，GE％和Mn可分别达到40％，225％，80％和1．4万。接枝共聚物在磷酸缓冲溶液和户外土壤掩埋降解实验表明，在160天内样品失重率分别为71％和60％，表明合成的乙酰化淀粉／DL－丙交酯接枝共聚物具有很好的降解性能。     

乙酸促进邻甲基苯磺酸铜选择性催化醇和酚的四氢吡喃化反应

室温无溶剂条件下, 乙酸能有效促进邻甲基苯磺酸铜催化一系列醇或酚和3,4-2H-二氢吡喃反应, 生成相应的四氢吡喃醚. 在乙酸存在条件下, 体系的催化性能有显著提高, 邻甲基苯磺酸铜用量仅需0.3 mol%(占醇或酚的摩尔分数)就能使反应在较短时间内完成. 反应结束后, 邻甲基苯磺酸铜经简单相分离可多次重复使用, 催化活性无明显下降. 产物结构经IR, 1H NMR, 元素分析进行表征.     

A preliminary study of a colorimetric method for anisole determination

The colour reaction between anisole, concentrated sulphuric acid and formaldehyde has been studied in glacial acetic acid as solvent The reaction can be used for the quantitative colorimetric analysis of anisole in mixtures with acetic acid and with benzene.     

Preparation and utilization of perillyl acetate

Perillyl acetate is a fragrance compound that was prepared by the reaction of β-pinenoxide with acetic anhydride and using acetic acid as an acid catalyst. Several selected catalysts were tested (homogenous: phosphoric acid, boric acid, acetic acid, and citric acid; heterogeneous: zeolite USY, SSA, and montmorillonite K-10) and the reaction conditions optimized for this reaction. The yield 78.7 % of perillyl acetate was obtained. Mayol (4-isopropylcyclohexylmethanol), a valuable fragrance compound, was further obtained by a two-step synthesis from perillyl acetate. Firstly, perillyl acetate was saponified to perillyl alcohol. The yield of alcohol was 94.4 %. The last step of the entire preparation was the hydrogenation of perillyl alcohol to Mayol. The yield of the desired product of this reaction was 94.6 %.     

平头pH电极-流动注射联用技术快速滴定食醋中醋酸的方法研究

采用一种具有平头结构的pH电极作为流动注射分析(FIA)的检测器,构建了流动注射自动化酸度滴定系统.优化了样品进样量、流速、载液浓度和反应管长度等参数.用NaOH溶液作为载液,在4.639×10-4～0.212 mol·L-1范围内醋酸浓度的对数与FIA峰的峰面积成正比,该方法的相对标准偏差(RSD)小于0.5%.采用...     

Characterization of moisture-sensitive raw materials with simple spectroscopic techniques

The quality of raw materials used in a synthetic process needs to be properly controlled in order to ensure optimal reaction conversion and desired quality of the resulting product. For air and water sensitive raw materials, quantitative analysis can be a challenging task. Spectroscopic techniques possess advantages of simple operation, fast analysis, low consumable costs and high sample throughput for the analysis of reactive raw materials. Three case studies utilizing spectroscopic analysis for air and water sensitive materials are discussed. First, FT-IR spectroscopy was utilized to determine the amount of residual acetic acid in acetic anhydride key raw material. Acetic anhydride was used in a methylenation reaction where the presence of residual acetic acid could quench a base used in the reaction, leading to incomplete conversion. A simple, one-frequency calibration method was developed to quantify acetic acid in acetic anhydride (2-35 wt.%). Next, a novel near infrared reflectance spectroscopy (NIRS) method was used to determine the concentration of diisobutyl aluminum hydride (DIBAL-H) in toluene. DIBAL-H is a highly reactive and moisture-sensitive reagent used as a key raw material for the reduction of an active intermediate. A calibration method based on one-frequency was also developed to determine the concentration of DIBAL-H in toluene (0-1.5 mole/L). Finally, a NIRS method based on partial least squares regression (PLS) was developed to quantify p-toluenesulfonic acid in p-toluenesulfonic anhydride, which is not amenable to chromatographic analysis.     

疏水双功能介孔固体酸的合成及其在乙酸乙酯酯化反应中的应用

通过水热合成法一步合成了具有不同疏水基团－CH₃ 、－(CH₃)₂ 和－(CH₃)₃的双功能介孔固体酸SBA-15-SO₃H－(CH₃)_x催化剂。通过X射线粉末衍射(XRD)、N₂吸脱附、元素分析等方法对催化剂进行了表征,并在乙酸乙酯酯化反应中进行催化性能评价。结果表明,随着疏水前驱体中甲基数的增加,样品的疏水性增强。SBA-15-SO₃H-(CH₃)_x催化剂的催化活性随着疏水性的增强而提高,而具有较强疏水性的材料SBA-15-SO₃H-(CH₃)₃在反应中具有较高的催化性能。以SBA-15-SO₃H-(CH₃)₃为催化剂,酯化反应的最优条件为：温度为120℃,乙酸与乙醇摩尔比为4∶1,催化剂质量分数为1 %,反应时间为1h。在此条件下,乙醇的转化率和乙酸乙酯的选择性分别为93%和100%。     

磷钨酸催化合成乙酸戊酯

以磷钨酸为催化剂,冰醋酸和戊醇为原料,催化合成了乙酸戊酯.探讨了催化剂用量、醇酸比、反应时间等对酯化反应的影响.研究结果表明:取冰醋酸40mL,正戊醇25mL,磷钨酸2.0g,反应时间为2h时,酯的产率大于80%.     

Oxidation of 4-Nitrotoluene by Ozone in Acetic Anhydride in the Presence of Manganese Sulfate

The reaction of 4-nitrotoluene oxidation with ozone in acetic anhydride in the presence of MnSO₄and sulfuric acid was studied. The main reaction product is 4-nitrobenzyl acetate, the yield of which is 63.2%. Based on an analysis of the experimental data, a mechanism of the catalytic ozonation of 4-nitrotoluene in acetic anhydride was proposed.     

Graft Copolymerization of (Dimethylamino)Ethyl Methacrylate onto Chitosan Initiated by Ceric Ammonium Nitrate

Abstract

(Dimethylamino)ethyl methacrylate (DMAEMA) was grafted onto chitosan using ceric ammonium nitrate as initiator in acetic acid solution. The effects of reaction variables on the grafting percentage and efficiency percentage were investigated, including the amounts of monomer and initiator, reaction time and reaction temperature. The grafted copolymers were confirmed by FTIR, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of TGA and DSC indicated the improvement of thermal stability for chitosan‐g‐poly(PDMAEMA). Solubility test revealed the improved hydrophilicity of grafted chitosan in aqueous acetic acid solution, and its swelled behavior in mixtures of glacial acetic acid and anhydrous ethanol (the ratios of 1:1 and 1:2, v/v). The grafted copolymer possessed amphiphilic structure and exhibited properties of polymeric surfactant.     

Head-to-head vinyl chloride–vinyl acetate copolymer

Addition chlorination of cis-1,4-polybutadiene in the presence of acetic acid as a cosolvent resulted in the formation of head-to-head vinyl chloride–vinyl acetate copolymer. Chlorine analysis, IR, and NMR spectra of the chlorinated polybutadiene indicated that reaction was primarily double bond addition; there was little evidence for substitutive chlorination. Acetate was incorporated by nucleophilic participation of the acetic acid cosolvent. The extent of incorporation of the acetate group in the polymer chain was a function of the acetic acid concentration. Both the glass transition temperatures and the densities of the chloroacetylated polymers decreased as the degree of acetylation increased.