XRD and AFM studies of ZnS thin films produced by electrodeposition method

The structure and morphology of ZnS thin films were investigated. ZnS thin films have been grown on an indium tin oxide glass substrate by electrodeposition method using zinc chloride and sodium thiosulfate solutions at room temperature. The X-ray diffraction patterns confirm the presence of ZnS thin films. From the AFM images, grain size decreases as the cathodic potential becomes more negative (from ?1.1 to ?1.3 V) at various deposition periods. Comparison between all the samples reveals that the intensity of the peaks increased, indicating better crystalline phase for the films deposited at ?1.1 V. These films show homogeneous and uniform distribution according to AFM images. On the other hand, XRD analysis shows that the number of ZnS peaks increased as deposition time was increased from 15 to 30 min at ?1.1 V. The AFM images show thicker films to be formed at ?1.1 V indicating more favourable condition for the formation of ZnS thin films.     

沉积电位对电沉积ZnS薄膜的影响

采用电沉积方法,在不同沉积电位条件下,在氧化锡铟(ITO)导电玻璃上沉积制备了ZnS薄膜,利用XRD、SEM和UV-VIS测试技术对在不同沉积电位所制备薄膜的晶相结构、表面微观形貌和光学性能进行了表征.研究结果表明:沉积电位在1.5 V—1.7 V范围内制备的ZnS薄膜呈非晶态,其可见光透过率从60 %降低到20 %,薄膜的光学带隙约为3.97 eV.在沉积电位为2.0 V条件下所沉积薄膜为ZnS结晶相和金属Zn混合相,薄膜透过率显著降低.     

Pulsed Laser Deposition ZnS Buffer Layers for CIGS Solar Cells

Polycrystalline ZnS films were prepared by pulsed laser deposition （PLD） on quartz glass substrates under different growth conditions at different substrate temperatures of 20, 200, 400, and 600 ℃, which is a suitable alternative to chemical bath deposited （CBD） CdS as a buffer layer in Cu（In,Ga）Se2 （CIGS） solar cells. X-ray diffraction studies indicate the films are polycrystalline with zinc-blende structure and they exhibit preferential orientation along the cubic phase β-ZnS （111） direction, which conflicts with the conclusion of wurtzite structure by Murali that the ZnS films deposited by pulse plating technique was polycrystalline with wurtzite structure. The Raman spectra of grown films show Al mode at approximately 350 cm^-1, generally observed in the cubic phase β-ZnS compounds. The planar and the cross-sectional morphology were observed by scanning electron microscopic. The dense, smooth, uniform grains are formed on the quartz glass substrates through PLD technique. The grain size of ZnS deposited by PLD is much smaller than that of CdS by conventional CBD method, which is analyzed as the main reason of detrimental cell performance. The composition of the ZnS films was also measured by X-ray fluorescence. The typical ZnS films obtained in this work are near stoichiometric and only a small amount of S-rich. The energy band gaps at different temperatures were obtained by absorption spectroscopy measurement, which increases from 3.2 eV to 3.7 eV with the increasing of the deposition temperature. ZnS has a wider energy band gap than CdS （2.4 eV）, which can enhance the blue response of the photovoltaic cells. These results show the high-quality of these substitute buffer layer materials are prepared through an all-dry technology, which can be used in the manufacture of CIGS thin film solar cells.     

A study on electrodeposited of ZnO/ZnS heterostructures

ZnO/ZnS heterostructures were synthesized by a two steps electrochemical deposition method. Firstly, ZnS layer was deposited from an aqueous solution containing Na₂S₂O₃ and ZnSO₄ onto indium-doped tin oxide (ITO) coating glass substrate at two deposition potentials. Then, ZnO nanostructures were deposited from an aqueous solution of Zn(NO₃) onto ZnS surface. The as-obtained samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), Raman and UV-visible analysis. The results indicate that the electrodeposition of ZnS layer at ?0.9 V give the best proprieties of ZnO/ZnS heterostructures. Homogeneous and uniform surface of ZnO/ZnS heterostructure was confirmed by AFM images. The XRD patterns indicates a high crystallinity of ZnO/ZnS. A high transmittance of 65% was also noted from UV-Visible spectra and band gap energy as large as 3.6?eV was found.     

Synthesis and characterization of high-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) luminescent nanocrystals

High-quality ZnS, ZnS:Mn2+, and ZnS:Mn2+/ZnS (core/shell) nanocrystals (NCs) were synthesized via a high-boiling solvent process and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electron paramagnetic resonance (EPR), X-ray photoelectron spectroscopy (XPS), and photoluminescence (PL) spectra. The monodisperse ZnS NCs (size = 8 nm), which self-assembled into several micrometer-sized domains, were achieved by adopting poly(ethylene glycol) (PEG) in the reaction process (without using a size-selection process). The obtained ZnS:Mn2+ and ZnS:Mn2+/ZnS core/shell NCs are highly crystalline and quasimonodisperse with an average particle size of 6.1 and 8.4 nm, respectively. All of the as-formed NCs can be well dispersed in hexane to form stable and clear colloidal solutions, which show strong visible emission (blue for ZnS and red-orange for ZnS:Mn2+ and ZnS:Mn2+/ZnS) under UV excitation. The growth of a ZnS shell on ZnS:Mn2+ NCs, that is, the formation of ZnS:Mn2+/ZnS core/shell NCs, resulted in a 30% enhancement in the PL intensity with respect to that of bare ZnS:Mn2+ NCs due to the elimination of the surface defects.     

An improved method for chemical bath deposition of ZnS thin films

ZnS thin films were prepared by an improved chemical bath deposition method, which the substrates were preheated before being mounted in the reaction solution. X-ray diffraction (XRD) and energy dispersive spectrometer (EDS) reveals that thin film ZnS has a cubic structure and the typical composition ratio of Zn/S is 52:48. Scanning electron microscopy (SEM) characterization shows that the surface of the sample is compact and uniform. The transmission spectrum indicates a good transmission characteristic with an average transmittance of 82.2% in the spectra range from 350 nm to 800 nm and the optical band gap is about 3.76 eV.     

In-situ investigations on the SILAR-growth of ZnS films as studied by tapping mode atomic force microscopy

Tapping mode atomic force microscopy (TM-AFM) has been successfully used for in-situ imaging of the deposition of ZnS films with the successive ionic layer adsorption and reaction (SILAR) method. The films were deposited in-situ using the commercial TM-AFM liquid cell as a flow-through reactor. The potential of TM-AFM has been used to study the growth of ZnS on different substrates up to 50 SILAR cycles. Reactants and rinsing water were alternately exchanged in the cell by a computer controlled valve system. In comparison to earlier work performed with the conventional AFM operated in contact mode, imaging artefacts introduced by lateral shear forces can be largely eliminated with TM-AFM. On glass the roughness is observed to decrease initially until typical island formation takes place at a larger number of deposition cycles. On mica island formation can be observed right from the beginning of the process and the roughness increases with increasing number of deposition cycles.     

Preparation and characterization of thin TiO2-films on gold/mica

Flat and highly (111) oriented gold and silver films were prepared by physical vapour deposition (PVD) using optimized deposition parameters. On these films, which were characterized with atomic force microscopy (AFM), scanning tunneling microscopy (STM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), titanium dioxide films were deposited by electron beam evaporation and dip coating. Dip coating from titanium tetraisopropoxide solutions resulted in films with different morphology and coverage depending on the alkoxide concentration (0.009 mol/L – 0.60 mol/L) and the post-treatment. Scanning electron microscopy (SEM) and AFM revealed that the deposited TiO₂ consists of amorphous, highly porous islands when the applied alkoxide concentration is high (0.05 mol/L – 0.6 mol/L). At higher temperatures these amorphous TiO₂ islands sintered significantly and crystallized to anatase. In contrast, transparent TiO₂ films were obtained from low concentrated alkoxide solutions (< 0.01 mol/L) which covered the whole substrate, similar to electron beam evaporated thin films. Sputter profiles with ion scattering spectroscopy (ISS) indicated that the film thickness is in the range of 2 nm when alkoxide solutions with a concentration of 9 mmol/L are used. The deposition of TiO₂ by electron beam evaporation normally resulted in significantly reduced TiO₂ films, completely oxidized ones were obtained when deposition was performed at elevated oxygen partial pressures (p(O₂) > 2 × 10^–5 mbar).     

三维SiO2欧泊模板溶剂热法制备硫化锌光子晶体

以单分散二氧化硅微球在重力场下自组装得到的三维有序欧泊(opal)为模板，采用溶剂热法在模板空隙内生长ZnS晶体，从而制备高质量的硫化锌基光子晶体. 通过X射线衍射(XRD)和Raman光谱证明ZnS晶体为闪锌矿结构且晶体质量较好，并对其生长机理进行了讨论. 通过场发射扫描电子显微镜(FESEM)和紫外-可见分光光度计对所合成的ZnS/opal复合物与ZnS反欧泊结构进行了表征，结果表明两种结构都保持了欧泊三维有序性，并且在Г-L方向(垂直于(111)方向)上出现了布拉格衍射峰，说明其具有良好的光子晶体特性.     

SBA-15模板法合成硫化锌纳米束及其光电性能

以乙基黄酸锌(ZnR2)作为单分子前驱体, SBA-15作为模板, 合成高度有序的ZnS纳米束, 并通过透射电子显微镜(TEM)、热重-差热分析(TG-DTA)、X射线衍射(XRD)、N2吸附-脱附、紫外-可见(UV-Vis)光谱、荧光光谱和扫描电子显微镜(SEM)等一系列手段对其形貌、结构及性能进行表征. 结果表明, 此阵列具有高度有序的六方介孔结构, 同时具有类似于母模板的纤维状形貌. 采用一种简单的交流电场辅助的方法把纳米束组装到电极上, 然后通过半导体表征仪器进行测试, 表征结果发现单束ZnS纳米束呈现出非线性的整流行为, 在紫外光照射下, 其电流-电压(I-V)曲线发生了很大的变化, 说明利用它们组装的纳米器件具有良好的光开关效应,并对整流及光响应机理进行了解释.     

Structure-directing coordination template effect of ethylenediamine in formations of ZnS and ZnSe nanocrystallites via solvothermal route

ZnS and ZnSe precursors (ZnS x 0.5en and ZnSe x 0.5en, en = ethylenediamine) were prepared via a solvothermal process using ethylenediamine as solvent. Phase-pure hexagonal wurtzite ZnS and ZnSe products were obtained by annealing the precursors in argon stream at temperatures above 350 degrees C. The role of ethylenediamine as a structure-directing coordination molecular template responsible for the morphologies of the annealed products was discussed. This work provided further insights into the solvent coordination molecular template (SCMT) mechanism previously proposed to explain the growth mechanism of CdE (E = S, Se, Te) nanorods in ethylenediamine (Inorg. Chem. 1999, 38, 1382). The as-prepared precursors as well as the annealed products were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared absorbance spectroscopy (IR), thermogravimetric analysis (TGA), X-ray fluorescence (XRF) analysis, and combustion analysis for C, N, H contents.     

ZnS nanosheets: Egg albumin and microwave-assisted synthesis and optical properties

ZnS nanosheets were prepared via egg albumin and microwave-assisted method. The phases, crystalline lattice structures, morphologies, chemical and optical properties were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), field-emission scanning electron microscope(FE-SEM), selected area electron diffraction (SAED), Fourier transform infrared (FTIR) spectroscopy, ultraviolet–visible (UV–Vis) spectroscopy and fluorescence(FL) spectrometer and growth mechanism of ZnS nanosheets was investigated. The results showed that all samples were pure cubic zinc blende with polycrystalline structure. The width of ZnS nanosheets with a rectangular nanostructure was in the range of 450–750 nm. The chemical interaction existed between egg albumin molecules and ZnS nanoparticles via the amide/carboxylate group. The band gap value calculated was 3.72 eV. The band at around 440 nm was attributed to the sulfur vacancies of the ZnS nanosheets. With increasing volumes of egg albumin, the photoluminescence (PL) intensity of ZnS samples firstly increased and then decreased, attributed to concentration quenching.     

Low-temperature growth and photoluminescence property of ZnS nanoribbons

At a low temperature of 450 degrees C, ZnS nanoribbons have been synthesized on Si and KCl substrates by a simple chemical vapor deposition (CVD) method with a two-temperature-zone furnace. Zinc and sulfur powders are used as sources in the different temperature zones. X-ray diffraction (XRD), selected area electron diffraction (SEAD), and transmission electron microscopy (TEM) analysis show that the ZnS nanoribbons are the wurtzite structure, and there are two types-single-crystal and bicrystal nanoribbons. Photoluminescence (PL) spectrum shows that the spectrum mainly includes two parts: a purple emission band centering at about 390 nm and a blue emission band centering at about 445 nm with a weak green shoulder around 510 nm.     

Poly(MAA-Mn) for Triple-Layer Structure Synthesis of ZnS/ZnS:Mn/SiO2 Phosphors

Methacrylic acid (MAA) was used as a manganese carrier to prepare ZnS/MAA-Mn particles, and ZnS/ZnS:Mn phosphors were formed from ZnS/MAA-Mn by ion substitution through heat treatment. After silica coating on surface by chemical precipitation method with tetraethyl orthosilicate (TEOS), ZnS/ZnS:Mn/SiO₂ phosphors were prepared successfully as a new core/shell structure compound. The thickness of layers was controlled by adjusting concentrations of manganese (II) acetate (Mn(CH₃COO)₂) and TEOS. Structure, morphology, and composition of prepared phosphors were investigated by X-ray diffraction (XRD), transmission electron microscope (TEM), and X-ray photoelectron spectroscopy (XPS), respectively. Photoluminescence (PL) properties of ZnS with different Mn²⁺ content were analyzed by PL spectrometer. PL emission intensity and PL stability were analyzed for evaluating effects of silica coating and Mn²⁺ activator doping. As a result, the structure of two layers could be observed, and optimum composition of ZnS/ZnS:Mn/SiO₂ structure was also obtained.     

Synthesis of functionalized Cu:ZnS nanosystems and its antibacterial potential

Copper doped Zinc Sulfide (Cu:ZnS) nanoparticles were synthesized as potential antibacterial agents, through a solvothermal approach using Mercaptosuccinic acid (MSA) and Sodium citrate (SC) as differential capping agents. Multiple variants of the Cu:ZnS nanoparticles were generated based on the refluxing intervals of the reactions and a choice of the capping agents. The microstructural properties and the elemental composition of the synthesized nanosystems were examined using Scanning Electron Microscopy (SEM) and powder X-ray Diffraction (XRD), along with Energy-Dispersive X-ray spectroscopy (EDX) and Microwave Plasma-Atomic Emission Spectroscopy (MP-AES). The as-synthesized nanosystems were also characterized for their surface attributes using Fourier Transform Infrared spectroscopy (FT-IR), while the optical properties were studied using UV–Vis spectroscopy. The electrostatic stability of the aqueous dispersions of Cu:ZnS was studied as a function of their solvent pH, using Photon Correlation Spectroscopy. For the assessment of the antibacterial properties of the different variants of Cu:ZnS nanosystems, the disk diffusion assay was performed against both Gram-positive and Gram-negative bacteria. The results show a promising antibacterial activity for the Cu:ZnS variants synthesized, with a prominent activity in the [email protected]:ZnS nanoparticle making them a novel class of potential antibacterial agents.     

AFM and XRD investigation of crystalline vapor-deposited C60 films

The morphological and structural properties of C(60) films deposited on quartz substrates by sublimation at 320-500 degrees C under high vacuum have been investigated using atomic force microscopy (AFM) and reflection X-ray diffraction (RXRD). The thickness of the films varied between 0.2 microm and 10 microm. AFM showed that the films consist predominantly of cubic crystals of a few micrometer in size with well-developed (111) and (100) faces. The crystallographic investigation revealed a strongly preferred [111] growth direction which is very sensitive to the deposition rate and substrate temperature. The influence of the experimental parameters on the morphology of the crystals and on the preferred orientation of the films is discussed in view of the AFM and RXRD results.     

硫化锌与硫化锌/氧化锌异质结纳米线的化学气相沉积法制备与表征

介绍一种利用石墨还原快速制备大量硫化锌纳米线的方法,并分别合成了超晶格型、双轴型、核/壳型的硫化锌/氧化锌异质结纳米线。所合成的硫化锌纳米线存在六方纤锌矿和立方闪锌矿两种晶型,纳米线长度达几十微米,直径在20-50 nm,直径均匀且产量很高。在具有双轴型的硫化锌/氧化锌异质结中,首次发现具有超结构特征的氧化锌。HRTEM分析表明,硫化锌/氧化锌超晶格异质结界面为ZB-ZnS(111)∥ZnO(0001),而核/壳型异质结界面为W-ZnS(0001)∥ZnO(0001),这三个晶面分别为各自晶体的极性面,即所合成的硫化锌/氧化锌异质结中极性面相互平行。对ZnS 和ZnS/ZnO 异质结的生长机制进行了探讨,并对硫化锌纳米线与硫化锌/氧化锌异质结的光学性质进行了分析。     

Chelating ligand-mediated synthesis of hollow ZnS microspheres and its optical properties

Monodispersed hollow ZnS microspheres have been successfully synthesized by a facile ethylenediamine tetraacetic acid (EDTA) mediated hydrothermal route. The sizes of the hollow spheres vary from 1.5 to 3.5 microm when the reaction temperature varied from 130 to 230 degrees C. The formation of these hollow spheres is attributed to the oriented aggregation of ZnS nanocrystals around the gas-liquid interface between H(2)S and water. EDTA plays important role as chelating ligand and capping reagent, which regulates the release of Zn(2+) ions for the formation of ZnS hollow spheres. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis spectroscopy, photoluminescence, and Raman spectroscopy. The obtained ZnS hollow spheres show a sharp and photostable UV emission approximately 370 nm, which is attributed to the recombination process associated with interstitial sulfur vacancy.     

CuInS_2/ZnS量子点的微波水热合成与表征——推荐一个研究型综合实验

介绍一个研究型综合实验——简易微波水热合成CuInS_2/ZnS复合量子点及其表征。实验通过Cu~(2+)、In~(3+)、Zn~(2+)和S~(2-)离子为原料,以谷胱甘肽作为稳定剂,两步微波水热合成水溶性的CuInS_2/ZnS复合量子点。用X射线衍射法和透射电镜表征它的结构和形貌,用紫外-可见光吸收、荧光光谱、荧光寿命和荧光照片等表征光学性质,并探究温度、时间、成份对荧光性质的影响。通过该实验的设计与实施培养学生科学研究的方法和思维能力。     

Surfactant-assistant and facile synthesis of hollow ZnS nanospheres

Small and monodisperse ZnS hollow nanospheres with outer diameter ranging from 60 to 70 nm and wall thickness of 15-20 nm were fabricated in a large scale by a simple surfactant polyethylene glycol (PEG) assisted method. The diameter and the wall thickness of the hollow nanospheres could be controlled by manipulating the amount of PEG and the aging time, respectively. Moreover, the wall of these hollow nanospheres is very compact. The product was characterized by X-ray power diffraction (XRD), transmission electron microscopy (TEM), UV-vis spectrum and fluorescence spectroscopy. The photocatalytic activity of as-prepared ZnS hollow nanospheres was also evaluated by using methyl orange (MO) as a model organic compound and the result revealed that their photocatalytic activity is a little lower than that of Degussa P25 TiO(2) but better than that of ZnS nanocrystals prepared by literature method. Furthermore, a rational mechanism to the formation and evolution of the products is proposed.