考虑弥散效应的多孔介质中超绝热燃烧的数值模拟

研究多孔介质内往复流动下的超绝热燃烧。一维模型包括气体输运、多孔介质固体的辐射、导热和气固两相间的对流换热。通过数值计算研究超绝热燃烧的形成、以及弥散效应、当量比和多孔介质材料本身对超绝热燃烧特性的影响。计算结果的有效性通过实验进行了验证并取得了相同的趋势。结果表明,组分弥散效应对气体温度分布和反应热影响很小;同一工况下,不考虑气体混合物的热弥散效应,会导致过高的气体温度计算值。同时,计算结果表明小孔径的多孔介质更有利于贫可燃极限的扩展,对30 ppi的多孔介质燃烧器,得到了当量比为0．092的可燃极限。     

双层多孔介质内预混燃烧的实验和二维数值模拟

对双层多孔介质燃烧器内丙烷/空气预混燃烧进行实验和数值研究.实验对多孔介质燃烧器内固体温度场分布进行测量分析;数值计算利用商业软件FLUENT6.2,通过添加用户自定义标量方程和用户自定义函数,对有壁面散热的双层多孔介质内预混燃烧进行了二维模拟,并与实验结果进行了比较.结果表明,双层多孔介质燃烧器具有良好的稳定燃烧范围和较低的污染物排放;壁面散热对多孔介质燃烧的影响不可忽视.     

微细多孔介质中对流换热实验研究

本文对空气流过烧结微细多孔介质内部的对流换热进行了实验研究。实验段为烧结多孔介质,颗粒的平均直径为0．2 mm。通过“单吹法”的实验方法进行瞬态实验,并用两种不同的数据处理方法得到了多孔介质内部对流换热系数。数据处理方法1利用局部非热平衡能量方程,结合实验数据,数值求得了多孔介质内部对流换热系数。方法2利用实验数据直接求得内部对流换热系数。研究表明:用数据处理方法1得到的多孔介质内部对流换热系与用方法2得到的结果相差在10％以内,与已有结果基本吻合。     

前沿领域综述–多孔介质强制对流换热研究进展

多孔介质的强制对流换热主要涉及渗流、对流换热、热弥散和热辐射等方面的内容, 文中对这个几个方面的国内外研究进展和发展趋势进行了逐一综述. 同时对主要理论模型、实验研究和经验关联式进行了分类整理, 总结了它们的特点、适用范围和局限性, 并对主要研究成果进行了对比分析, 指出了将来进一步研究的方向和难点所在. 而且通过简化计算得到高温多孔介质冷却过程何时需要考虑辐射换热. 所有这些对多孔介质的理论研究和工程应用都具有指导性的意义. 关键词： 多孔介质 对流换热 渗流 热弥散     

颗粒有序堆积多孔介质对流换热实验研究

本文采用"瞬态单吹反问题研究方法"对颗粒有序堆积多孔介质内的强制对流换热进行了实验研究。详细研究了颗粒堆积方式变化对多孔介质内对流换热的影响,并对均匀与非均匀颗粒堆积多孔介质内的对流换热特性进行了对比分析。研究表明:通过对颗粒进行合理有序堆积,可以使相应多孔介质内的压降显著降低,其综合换热效率明显提高;通过拟合获得了颗粒有序堆积多孔介质内的宏观流动换热实验关联式,其形式与传统经验公式(Ergun公式和Wakao公式)一致,但部分模型参数值远低于传统经验公式。     

双层多孔介质内甲烷富燃制氢过程的研究

采用一维双温度体积平均模型和详细的甲烷化学反应机理GRI 3.0,对双层泡沫陶瓷多孔介质内甲烷富燃燃烧过程进行数值模拟,研究在双层多孔介质交界面附近稳定燃烧时的火焰稳定传播范围、火焰温度和组分分布及氢气的产量和能量转换效率.结果表明,双层多孔介质燃烧器能有效拓宽甲烷在空气中的富燃极限;在当量比大于1.6时,燃烧产物中氢气含量较多,氢气产生分为甲烷部分氧化和水煤气反应两个阶段;当量比在1.6～1,8之间时,能量转换效率较大,最大值约为46%.     

三维有序排列多孔介质对流换热的数值研究

利用CFD软件数值研究了颗粒三维有序堆积多孔介质的对流换热问题. 采用颗粒直径分别为14 mm,9.4 mm和7 mm的球形颗粒有序排列构成多孔介质骨架,在多孔骨架的上方有一恒热流密度的铜板. 采用流固耦合的方法研究了槽通道内温度分布和局部对流换热系数的分布以及对流换热的影响因素. 研究结果表明:热渗透的厚度和温度边界层的厚度在流动方向上逐渐增大,并且随流量的增加而减小;当骨架的导热系数比较高时,对流换热随颗粒直径的减小而略有增大;对流换热系数随聚丙烯酰胺溶液浓度的增大而减小,黏性耗散减弱了对流换热. 关键词： 多孔介质 温度场 局部对流换热系数 数值模拟     

微细多孔介质中对流换热研究

本文对空气、氦气和二氧化碳流过微细多孔介质内部的对流换热进行了实验研究和数值模拟。实验段为烧结多孔介质,颗粒的平均直径为40～225μm,通过单吹法的实验方法进行瞬态实验,得到了多孔介质内部对流换热系数。数值模拟了气体流过微细多孔结构内部的对流换热的非稳态过程,得到多孔介质内部对流换热系数。数值结果与实验结果基本一致,并与已有结果基本吻合。     

粘性耗散及变物性对多孔介质中对流换热的影响研究

本文通过理论分析、数值模拟与实验研究的综合,研究了粘性耗散及变物性对多孔介质中对流换热的影响。发现：用理想的等热流边界条件可以较好地数值模拟等热流边界条件下多孔介质中的对流换热;在实际可实现的参数条件下,粘性耗散对多孔介质中对流换热的影响不大;油的变物性对换热的影响很大—热流密度越高,对流换热越强。     

流体在烧结多孔槽道中对流换热的实验研究

本文对空气和水流过烧结青铜颗粒水平多孔槽道表面上的对流换热进行了实验研究。结果表明:与空槽道表面换热相比,实验段充满烧结多孔介质后,水流过实验段的平均对流换热系数可提高7～9倍,空气可提高3～30倍;烧结多孔结构的强化换热能力大于非烧结的堆积床;直径的增大能提高水在多孔结构内的换热能力,但对空气而言在实验流量范围内无明显作用。     

单只水平浓缩煤粉燃烧器在1MW燃烧试验台上的试验研究

单只水平浓缩煤粉燃烧器在１ＭＷ燃烧试验台上的试验研究孙绍增，吴少华，李争起，杨明新，王新雷，陈力哲，庞丽君，邢春礼，朱彤，孙恩召，秦裕琨（哈尔滨工业大学动力工程系哈尔滨１５０００１）关键词：水平浓淡燃烧，煤粉燃烧器，稳燃，低ＮＯ_ｘ一、引言电力工业对?..     

An experimental realization of an unstrained, planar diffusion flame

A unique burner was constructed to experimentally realize a one-dimensional unstrained planar non-premixed flame, previously considered only in idealized theoretical models. One reactant, the fuel mixture in the current experiments, is supplied through a porous plug at the bottom of the combustion chamber and flows vertically up towards the horizontal flame. The crux of the design is the introduction of the oxidizer from above in such a way that its diffusion against the upward product flow is essentially one-dimensional, i.e., uniform over the burner cross-section. This feature was implemented by introducing the oxidizer into the burner chamber from the top through an array of 625 closely spaced hypodermic needles, and allowing the hot products to escape vertically up through the space between the needles. Due to the injection of oxidizer through discrete tubes, a three-dimensional “injection layer” exists below the exit plane of the oxidizer supply tubes. Experimental evidence suggests that this layer is thin and that oxidizer is supplied to the flame by 1-D counterdiffusion, producing a nearly unstrained flame. To characterize the burner, flame position measurements were conducted for different compositions and flowrates of H₂–CO₂ and O₂–CO₂ mixtures. The measured flame locations are compared to an idealized one-dimensional model in which only diffusion of oxidizer against the product flow is considered. The potential of the new burner is demonstrated by a study of cellular structures forming near the extinction limit. Consistent with previous investigations, cellular instabilities are shown to become more prevalent as the initial mixture strength and/or the Damköhler number are decreased. As the extinction limit is approached, the number of cells was observed to decrease progressively.     

Stabilized,flat iron flames on a hot counterflow burner

Metal powder combustion has traditionally been studied to mitigate the risk of industrial accidents and to determine the contributions of metals as additives to the performance of energetic materials. Recently, there has been growing interest in exploring the potential of metal powders as recyclable, zero-carbon energy carriers as an alternative to the hydrocarbons known to contribute to climate change. The present work introduces, for the first time, a stabilized flat iron flame. The counterflow burner used in this work is comprised of an inverted ceramic nozzle which sits above, and is aligned axially with, a lower nozzle producing a laminar flow of particles suspended in an oxidizing gas. A stabilized methane flame sits inside the top nozzle and the hot combustion products impinge upon the two-phase flow from the bottom nozzle, creating a stagnation plane. Spherical iron powder, with 90% of the particles less than 2.5 µm in size, is pre-loaded into a piston and dispersed using mixtures of 30% and 40% oxygen balanced in argon. Flame speeds are measured using particle image velocimetry (PIV), while flame temperatures are determined using multicolour pyrometry. It is found that flame speeds range between 30 cm/s and 45 cm/s for both oxidizing mixtures. Despite having fuel loadings below stoichiometric concentrations, the observed particle combustion temperatures are close to the adiabatic flame temperature of the stoichiometric mixture, indicating combustion in the diffusion-controlled regime for these small particles. Finally, the independence of the flame speeds with respect to oxygen concentration suggests flame propagation in the discrete regime.     

Influence of Burner Geometry on Heat Transfer Characteristics of Methane/Air Flame Impinging on Flat Surface

An experimental study has been conducted to find the heat transfer characteristics of methane/air flames impinging normally to a flat surface using different burner geometries. The burners used were of nozzle, tube, and orifice type each with a diameter of 10 mm. Due to different exit velocity profiles, the flame structures were different in each case. Because of nearly flat velocity profile, the flame spread was more in case of orifice and nozzle burners as compared to tube burner. Effects of varying the value of Reynolds number (600–2500), equivalence ratio (0.8–1.5) and dimensionless separation distance (0.7–8) on heat transfer characteristics on the flat plate have been investigated for the tube burner. Different flame shapes were observed for different impingement conditions. It has been observed that the heat transfer characteristics were intimately related to flame shapes. Heat transfer characteristics were discussed for the cases when the flame inner reaction cone was far away, just touched, and was intercepted by the plate. Negative heat fluxes at the stagnation point were observed when the inner reaction cone was intercepted by the plate due to impingement of cool un-burnt mixture directly on the surface. Different heat transfer characteristics were observed for different burner geometries with similar operating conditions. In case of tube burner, the maximum heat flux is around the stagnation point and decay is faster in the radial direction. In case of nozzle and orifice burner, the heat transfer distribution is more uniform over the surface.     

渐变型多孔介质中燃气燃烧特性试验研究

试验研究预混燃气在渐变型多孔介质(GVPM)中的燃烧特性,包括在渐变型多孔介质中的温度场、火焰移动、CO和NOx生成、燃烧稳定性及多孔介质孔径结构对燃烧特性的影响规律。研究结果与几种均匀型多孔介质(HPM)中的燃烧特性进行比较,发现渐变型多孔介质中的燃烧有如下优点:均匀的温度分布、较低污染物排放、高燃烧速率、高稳定性、宽燃烧极限和较大的负荷调节范围。     

Flame stabilization with a tubular flame

A new technique to stabilize a flame in a high-velocity stream with use of a tubular flame has been proposed. To elucidate the validity of this technique, an experiment has been conducted by mounting a tubular flame burner on the nozzle. Flame stability limits and temperature distributions around the burner port have been determined, and experiments have been extended to the ducted combustion to measure pressure fluctuations and to analyze the burned gases. Results show that the tubular flame can successfully stabilize the main flame up to 130 m/s, which is the upper limit of the present supply facility. The main flame is well anchored at the exit of the nozzle, and the tubular flame efficiently supplies heat and radicals to the main flame. In the ducted combustion, the pressure fluctuations are reduced significantly. The exhaust gas analyses, however, indicate that an almost chemical equilibrium condition can be achieved at 50 m/s, but not at 90 and 130 m/s. Since the energy input relative to the main flame is just 6.1% at 130 m/s, the present tubular burner is not enough to burn all the unburned gas completely at high velocities, although the main flame can be anchored. The slit length and/or the slit width of the tubular flame burner should be larger to overcome this shortage. From the above results, it is concluded that the tubular flame has a potential for stabilizing a flame in a high-speed stream.     

材料性质和燃料特性对浸没在多孔介质中的液体燃料燃烧特性影响

本文研究了浸没在沙、钢珠和氟石等不同材料的多孔介质床中的液体燃料的燃烧特性.探讨了燃料性质对火焰特性、床层温度分布、离表面最近测点处蒸气区的下边界到达时间以及燃料消耗的影响.实验结果揭示了浸没在多孔床中的液体燃料燃烧的特殊规律.     

Characteristic regimes of premixed gas combustion in high-porosity micro-fibrous porous media

Dynamical behaviour of the premixed flame propagating in the inert high-porosity micro-fibrous porous media has been studied numerically. Effects of mixture filtration velocity, equivalence ratio and burner transverse size on the flame structure have been investigated and the regions of existence of different combustion regimes have been determined. It was found that the influence of the hydrodynamic instability on the flame dynamics is significant in the case of the moderate and high filtration velocities and this effect is negligible at the low velocities. At the moderate filtration velocities the effect of hydrodynamic instability manifests in the flame front deformation and in particular in the flame inclination. It was found that the flame can be stabilized within the whole interval of the filtration gas velocity, whereas in the ordinary porous media the standing wave is settled only at fixed value of gas filtration velocity. This finding is in line with recent experimental results on combustion in micro-fibrous porous media (Yang et al., Combust. Sci. Tech. 181 (2009), 1–16). Possible physical interpretation of the flame anchoring effect may be given on the base of present numerical analysis. At the high filtration velocities the hydrodynamic instability manifests itself in periodical appearance of the moving wrinkles on the flame front surface which forms non stationary high temperature trailing spots behind the leading part of the flame front. Such dynamics may be associated with splitting wave structures which were revealed in previous experiments (Yang et al., Combust. Sci. Tech. 181 (2009), 1–16).     

热氧喷嘴水煤浆扩散火焰辐射光谱特性研究

火焰的辐射光谱可为燃烧诊断提供诸多信息,因此目前对简单的气态火焰自由基辐射特性已进行了大量研究,而关于非均相火焰的辐射光谱特性研究则相对较少。采用改进的热氧喷嘴技术在敞开空间下直接点燃水煤浆,并利用光纤光谱仪和紫外成像系统,着重对甲烷和水煤浆火焰的辐射光谱及OH*的二维分布特性进行研究。结果表明：与甲烷火焰的光谱辐射相比,水煤浆火焰不仅存在OH*,CH*和C₂*特征辐射,还产生了Na*,Li*,K*和H*的发射谱线,并出现了连续的黑体辐射,这些光谱辐射特征可作为水煤浆气化或燃烧的标志,也可作为水煤浆是否点燃的判据;通入水煤浆后,OH*强度明显下降,而CH*和C₂*强度增大。对比甲烷火焰OH*二维分布,水煤浆火焰OH*峰值强度明显下降,化学反应区域面积显著减小;沿着火焰传播方向,甲烷和水煤浆火焰轴向的OH*强度均呈先增大后减小的趋势;甲烷火焰径向的OH*在反应核心区出现了双峰形态分布,而水煤浆火焰OH*径向始终呈单峰分布。随着氧碳当量比增大,水煤浆火焰OH*的存在范围扩大,说明氧气的增加促进了OH*的产生;随水煤浆流量提高,OH*的反应核心区域缩小,峰值强度明显下降,CH*,C₂*,Na*,Li*,K*和H*的强度显著增强,连续的黑体辐射强度也明显增大,这些辐射光谱的变化可用于表征操作负荷的变化。