新型聚芳醚酮与热致性液晶高聚物共混物流变性能和力学性能的研究

 本文研究了新型聚芳醚酮与热致性液晶高聚物(PEK-C/LCP)共混物的流变性能及力学性能。结果表明:由于LCP的加入,PEK-C的熔体粘度降低;随着剪切速率的增加,共混物熔体流动活化能从223.5KJ/mol降为102.2KJ/mol。共混物的玻璃化转变温度从纯PEK-C的218℃降为199℃;除模量增加外,其它力学性能均有所下降。同时利用SEM观察了共混物冲击断面形貌,未发现有LCP微纤维生成。     

PEK-C/PPS共混体系的相容性和结晶行为

结晶-非晶高聚物共混体系的相容性和结晶行为的研究已有许多报道。本工作研究了含酞侧基聚芳醚酮(PEK-C)与聚苯硫醚(PPS)共混物的相容性和结晶行为。 PEK-C为徐州工程塑料厂产品,未作封端处理,η?p/c=0.70;PPS为日本东丽产品。两者用双螺杆挤出机在320～350℃制成共混物。仪器为Perkin-Elmer DSC-7型差示扫描量热仪,升温速率10℃/min;DDV-Ⅱ-EA型全自动动态粘弹谱仪和理学D/max-ⅡBX-射线衍射仪。     

聚苯硫醚/尼龙6共混物界面对结晶行为的影响

高分子作为材料时 ,其力学性能受其结晶形态的影响 ,而其结晶形态与其结晶行为有关 .结晶性聚合物共混物中结晶组分由于第二组分存在 ,改变了结晶组分在熔体时的化学与物理环境 .因此 ,其结晶组分的结晶行为不仅取决于两组分在熔体时的相容性 ,而且与第二组分是否起到异相晶核作用和 /或两组分间界面是否诱导成核作用有关 ,从而影响共混物中结晶组分的结晶行为 ,导致共混物力学性能的改变[1～ 4] .在ＰＰＳ/ＰＡ6共混物中 ,由于ＰＰＳ的熔点和熔体结晶温度都比ＰＡ6的高 ,共混物熔体降温结晶ＰＰＳ是在ＰＡ6熔体存在下发生结晶 ,而ＰＡ6是在…     

酞侧基聚芳醚砜和聚芳醚酮的相容性

本文报道注射级酞侧基聚芳醚砜(PES-C)和聚芳醚酮(PEK-C)共混试样的玻璃化转变行为和部分力学性能的研究结果。并讨论共混工艺对相容性的影响。 PES-C和PEK-C树脂均由中国科学院长春应用化学研究所徐州工程塑料厂合成,在三氯甲烷中的比浓粘度ηsp/c(20℃)分别为0.45和0.47。将粉状树脂在GH-100Q高速搅拌器内按配方混合,并在烘箱内干燥后,用SHJ-30双螺杆挤出机在320～350℃(物料温度)挤出造粒。     

聚醚酰亚胺/酚酞型聚醚醚酮共混体系相容性的稀溶液粘度法研究

<正> 近年来,有关高性能树脂聚酰亚胺共混物的研究日益引起人们的关注。已经发现许多种分子结构不同的聚酰亚胺之间,聚酰亚胺与聚苯并咪唑,或聚醚醚酮能形成完全相容的共混体系,从而扩大了高性能树脂聚酰亚胺的应用范围。 酚酞型聚醚醚酮(PEK-C)是由我所研究开发出的一种新型的聚醚醚酮类高性能树脂,它具有良好的可溶性,优异的机械强度和加工流动性,已广泛应用于结构材料及复合材料的制备。为进一步扩大该树脂的应用范围,本实验室在PEK-C共混物的研究做了大量的工作。本工作研究了聚醚酰亚胺(PEI)/PEK-C共混体系的相容性。PEI和PEK-C的分子结构如下:     

PA6/HIPS/PP-g-(GMA-co-St)反应共混体系的研究

通过扫描电镜、热分析、熔体流动速率、熔融扭矩和力学性能等测试方法研究了甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(GMA-co-St)]对PA6/HIPS共混物的熔融流变性能、结晶行为、相形态和力学性能的影响.结果表明,在熔融共混过程中,PP-g-(GMA-co-St)中的环氧基与PA6的端氨基原位生成的接枝共聚物有效地降低了共混物的界面张力,提高了共混物的界面粘着力,使共聚物的流动速率降低,熔融扭矩提高;PA6分子链的规整性降低,结晶完善性变差.在PP-g-(GMA-co-St)的质量分数为10%时,共混物分散相的尺寸明显减少,力学性能得到较大提高;其中冲击强度超过纯PA6,达到HIPS水平.通过反应共混,制备了力学性能均衡的PA6/HIPS/PP-g-(GMA-co-St)共混物合金.     

POE-g-PMAH反应性增容PA1010/PP共混物的性能研究

乙烯-辛烯共聚物-g-聚马来酸酐(POE-g-PMAH)作为反应性增容剂,采用熔体共混的方法制备了PA1010/PP共混物,通过扫描电镜(SEM)、力学性能、傅立叶变换红外光谱(FTIR)和示差扫描量热(DSC)测试,研究了POE-g-PMAH对PA1010/PP共混物的增容作用.结果表明,POE-g-PMAH的加入可以减小共混物的相区尺寸,当PA1010/PP/POE-g-PMAH=70/30/15时,分散相尺寸小而均匀;FTIR结果表明接枝在POE上的马来酸酐基团和PA1010在熔融共混期间发生了化学反应;DSC研究结果表明共混体系中PA1010和PP的结晶温度和结晶度随POE-g-PMAH的加入而降低,表明POE-g-PMAH的增容作用对PA1010和PP的结晶有抑制作用.力学性能测试结果表明随着POE-g-PMAH的增加,共混物的冲击强度逐渐增加,当POE-g-PMAH含量增加到15%时,干态冲击强度达到21.13 kJ/m2,是不加增容剂的3.1倍,而拉伸和弯曲强度可以保持较高水平.POE-g-PMAH的增容机理在于其支链中的马来酸酐能与PA1010中的胺基(NH2—)发生化学反应,而主链POE与PP有较好的亲和性,从而降低界面张力,减少相区尺寸,大幅度提高力学性能.     

PP-g-(GMA-co-St)对PA6/PC共混物的反应增容作用

用红外、扫描电镜、熔体流动速率和力学性能等测试方法,研究了甲基丙烯酸缩水甘油酯(GMA)和苯乙烯(St)多单体熔融接枝聚丙烯[PP-g-(GMA-co-St)]对PA6/PC共混物的反应增容作用.研究结果表明,在熔融共混过程中,PP-g-(GMA-co-St)中的环氧基与PA6的端氨基及PC的端羟基原位生成的接枝共聚物有效地降低了共混物相间的界面张力,明显提高了共混物相界面的粘着力.少量的PP-g-(GMA-co-St)就能使PA6和PC的相容性得到显著改善.当PP-g-(GMA-co-St)的质量分数为10%时,共混物分散相的相区尺寸细化到0.2μm,其力学性能也有较大提高.PA6/PC/PP-g-(GMA-co-St)共混物的力学性能均衡,达到了弹性体增韧体系难以达到的效果.即使PP-g-(GMA-co-St)组分含量为20%时,共混物仍能保持较好的力学性能,特别是在共混物的韧性得以提高的同时,其强度和伸长率也提高.     

相分离对聚偏氟乙烯/聚甲基丙烯酸甲酯共混物的力学与耐紫外老化性能的影响

采用熔融共混法制备聚偏氟乙烯/聚甲基丙烯酸甲酯( PVDF/PMMA)共混物,考察其力学性能、耐紫外老化性能、熔体动态流变、结晶与热分解行为.PMMA含量(wPMMA)为10 wt％时,共混物形成均相结构,力学与耐老化性能最好.wPMMA≥20 wt％时,PMMA形成球状聚集体,共混物力学性能与耐候性显著降低.PMMA的存在可提高PVDF的结晶度,降低熔融温度,但不改变PVDF晶体结构.     

物理老化对PEK-C、PES-C及其复合材料的玻璃化转变热焓松弛特征的影响

本文用DSC技术研究了物理老化对PEK-C、PES-C及其共混物和复合材料玻璃化转变的影响.老化时间(t)延长,玻璃化转变温度(T_g)、热焓松弛峰温(T_(max))、峰高(△C_(pmax))和热焓(△H)提高;△H与lgt成线性关系.碳黑或碳纤维对PES-C的物理老化行为无影响,而反应性乙炔端基砜(ATS)固化物能限制PEK-C和PES-C在T_g以下温度的物理老化过程.利用物理老化能更为方便地判断多相体系的相容性,结果表明PEK-C/PSF为相容体系,而PEK-C/PES-C相容性较差.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.