Selective Voltammetric Detection of Uric Acid in the Presence of Ascorbic Acid at Well‐Aligned Carbon Nanotube Electrode

The voltammetric behaviors of uric acid (UA) and L ‐ascorbic acid (L ‐AA) were studied at well‐aligned carbon nanotube electrode. Compared to glassy carbon, carbon nanotube electrode catalyzes oxidation of UA and L ‐AA, reducing the overpotentials by about 0.028 V and 0.416 V, respectively. Based on its differential catalytic function toward the oxidation of UA and L ‐AA, the carbon nanotube electrode resolved the overlapping voltammetric response of UA and L ‐AA into two well‐defined voltammetric peaks in applying both cyclic voltammetry (CV) and differential pulse voltammetry (DPV), which can be used for a selective determination of UA in the presence of L ‐AA. The peak current obtained from DPV was linearly dependent on the UA concentration in the range of 0.2 μM to 80 μM with a correlation coefficient of 0.997. The detection limit (3δ) for UA was found to be 0.1 μM. Finally, the carbon nanotube electrode was successfully demonstrated as a electrochemical sensor to the determination of UA in human urine samples by simple dilution without further pretreatment.     

Selective Simultaneous Determination of Paracetamol and Uric Acid Using a Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotube/Chitosan Composite

A multiwalled carbon nanotube/chitosan modified glassy carbon electrode (MWCNTs‐CHT/GCE) has been used for simultaneous determination of paracetamol (PAR) and uric acid (UA). The measurements were carried out using differential pulse voltammetry (DPV), cyclic voltammetry (CV) and chronoamperometry (CA). DPV measurements showed a linear relationship between oxidation peak current and concentration of PAR and UA in phosphate buffer (pH 7) over the concentration range 2 µM to 250 µM, and 10 µM to 400 µM, respectively. The analytical performance of this sensor has been evaluated for detection of PAR and UA in human serum and human urine with satisfactory results.     

Bioanalytical Application of the Ordered Mesoporous Carbon Modified Electrodes

An ordered mesoporous carbon modified electrode (OMCE) was prepared by film forming method. The electrochemical behavior of the OMCE was evaluated in connection with the electrochemistry of some electroactive biospecies, such as ascorbic acid (AA), acetaminophenol (AP), cysteine (CySH), dopamine (DA), epinephrine (EP), uric acid (UA), β‐nicotinamide adenine dinucleotide (reduced disodium salt hydrate, NADH), and hydrogen peroxide (H₂O₂) with cyclic voltammetry. Compared with the conventional carbon nanotubes (CNT) and graphite powder (GP) modified electrodes, the OMCE provided the best electrochemical reactivities in all cases associated with decreased over potential, better‐defined peak shape, and higher sensitivity. In addition, the OMC, CNT, and GP modified electrodes were employed as sensitive sensors for H₂O₂ and NADH quantification and as stable platforms for the fabrication of glucose and ethanol biosensors on which the enzymes were immobilized.     

Ordered Mesoporous Carbon Paste Electrodes for Electrochemical Sensing and Biosensing

Surface renewable ordered mesoporous carbon paste electrodes (OMCPE) were prepared by mechanical mixing ordered mesoporous carbon (OMC) and mineral oil. Electrochemical behavior of the composite electrode was evaluated and compared with the conventional graphite paste (GPE) and carbon nanotubes paste (CNTPE) electrodes. The OMCPE provided improved electron transfer kinetics and catalytic capabilities in connection with oxidation and/or reduction of different redox systems, such as ferricyanide and some biological species, e. g. ascorbic acid (AA), uric acid (UA), β‐nicotinamide adenine dinucleotide (NADH), dopamine (DA), epinephrine (EP), acetaminophenol (AP) and hydrogen peroxide. The substantial decrease in the over voltage of the hydrogen peroxide oxidation along with the facile incorporation of glucose oxidase (GOD) into the composite matrix allowed us successfully to fabricate a sensitive and selective glucose biosensor. A linear response up to 15 mM glucose was obtained for the OMCPE modified with 10% GOD (w/w) with a detection limit of 0.072 mM. In addition, we also successfully applied the OMCPE to the anodic stripping voltammetric analysis of heavy metal ions with improved sensitivities in comparison with CNTPE and GPE. The excellent experimental results implicate that the new developed paste electrode holds great promise in the design of electrochemical devices, such as sensors and biosensors.     

Application of a Carbon‐Paste Electrode Modified with 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one and Carbon Nanotubes for Voltammetric Determination of Levodopa in the Presence of Uric Acid and Folic Acid

A carbon‐paste electrode modified with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one and carbon nanotubes was used for the sensitive voltammetric determination of levodopa (LD). The electrochemical response characteristics of the modified electrode toward LD, uric acid (UA) and folic acid (FA) were investigated. The results showed an efficient catalytic activity of the electrode for the electrooxidation of LD, which leads to lowering its overpotential by more than 320 mV. The modified electrode exhibits an efficient electron mediating behavior together with well‐separated oxidation peaks for LD, UA and FA. Also, the modified electrode was used for determination of LD in some real samples.     

Glassy Carbon Electrodes Modified with Multiwall Carbon Nanotubes Dispersed in Polylysine

We report the analytical performance of glassy carbon electrodes (GCE) modified with a dispersion of multiwall carbon nanotubes (MWCNT) in polylysine (Plys) (GCE/MWCNT‐Plys). The resulting electrodes show an excellent electrocatalytic activity towards different bioanalytes like ascorbic acid, uric acid and hydrogen peroxide, with important decrease in their oxidation overvoltages. The dispersion of 1.0 mg/mL MWCNT in 1.0 mg/mL polylysine is highly stable, since after 2 weeks the sensitivity for hydrogen peroxide at GCE modified with this dispersion remained in a 90% of the original value. The MWCNT‐Plys layer immobilized on glassy carbon electrodes has been also used as a platform to build supramolecular architectures by self‐assembling of polyelectrolytes based on the polycationic nature of the polylysine used to disperse the nanotubes. The self‐assembling of glucose oxidase has allowed us to obtain a supramolecular multistructure for glucose biosensing. The influence of glucose oxidase concentration and adsorption time as well as the effect of using polylysine or MWCNT‐Plys as polycationic layers for further adsorption of GOx is also evaluated.     

Construction of a Highly Selective and Sensitive Dopamine Enzyme-free Biosensor Based on Carbon Nanomaterials

A selective and sensitive electrochemical enzyme-free sensor for dopamine (DA) was prepared, containing carbon nanomaterials, gold nanoparticles (GNPs) and room-temperature ionic liquid of 1-butyl-3-methylimidazolium tetrafluor (BmimBF₄). The peaks of DA, ascorbic acid (AA) and uric acid (UA) can be well separated by optimization of pH condition and carbon nanomaterials.Multi-walled carbon nanotubes (MWCNTs), single-walled carbon nanotubes (SWCNTs), single-walled carbon nanohorns (SWCNHs), carboxylated graphene (C-GR), were chosen to compare the affection to DA detection. The catalytic effect was SWCNTs>MWCNTs>C-GR≈SWCNHs. It showed carbon nanotube materials with electron acceleration channels play the key role in catalytic performance. The pH condition also influenced detection, all the redox peak potentials of DA, UA, and AA had a negative shift as the pH changed from low to high, but the amplitude of the shift was different. At pH 1, the three anodic peaks are separated ca.0.24 V and 0.20 V. Under optimum conditions linear calibration graphs were obtained over the DA concentration range 0.2 to 20 μM.The modified electrode was applied for the assay of spiked DA in blood serum and human urine.This work studied the influence of carbon nanomaterials on DA detection and provided a simple approach to selectively detect dopamine in the presence of AA and UA.     

Monodispersed Gold Nanoparticles Decorated Carbon Nanotubes as an Enhanced Sensing Platform for Nanomolar Detection of Tramadol

A promising composite‐modified glassy carbon electrode is fabricated by electrodeposition of mono‐dispersed gold nanoparticles onto carbon nanotubes (AuNPs/CNTs/GCE). The electroanalysis of Tramadol (TRA) was achieved by different electrochemical techniques. The effect of different parameters including pH, concentration and potential scan on the oxidation current signal of TRA was investigated. Large excess of ascorbic acid (AA) and uric acid (UA) with a maximum molar ratio of 1/1000 and 1/100, respectively, did not interfere with the response of TRA. The detection limit with high sensitivity is 68 nM. TRA was successfully determined in pharmaceutical dosage forms, without any pretreatment of the samples.     

Selective detection of dopamine in the presence of ascorbic acid and uric acid by a carbon nanotubes-ionic liquid gel modified electrode

The electrochemistry of dopamine (DA) was studied by cyclic voltammetry at a glassy carbon electrode modified by a gel containing multi-walled carbon nanotubes (MWNTs) and room-temperature ionic liquid of 1-octyl-3-methylimidazolium hexafluorophosphate (OMIMPF₆). The thickness of gel on the surface of the electrode has to be controlled carefully because the charging currents increase with the modified layer being thicker. The anodic peaks of DA, ascorbic acid (AA) and uric acid (UA) in their mixture can be well separated since the peak potential of AA is shifted to more negative values, while that of UA is shifted to more positive values due to the modified electrode. At pH 7.08 the three peaks are separated ca. 0.20 and 0.15 V, respectively; hence DA can be determined in the presence of UA and more than 100 times excess of AA. Under optimum conditions linear calibration graphs were obtained over the DA concentration range 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ M. The detection limit of the current technique was found to be 1.0 × 10⁻⁷ M based on the signal-to-noise ratio of 3. The modified electrode has been successfully applied for the assay of DA in human blood serum. This work provides a simple and easy approach to selectively detect dopamine in the presence of ascorbic acid and uric acid.     

Quantification of methyldopa in pharmaceuticals using a glassy carbon electrode modified with carbon nanotubes

The quantification of methyldopa in pharmaceuticals has been carried out using a glassy carbon electrode(GCE) modified with multi-walled carbon nanotubes(MWCNTs). Methyldopa exhibited a quasi-reversible response with a peak potential separation of 473 m V on a bare GCE. However, the cyclic voltammetric behaviour of methyldopa was improved with the increase of the amount of MWCNTs. It was also shown that the electrocatalytic activity of the electrode towards the response of methyldopa was higher with larger amount of film on the surface. The results showed that the peak current was proportional to the concentration of methyldopa with a linear dynamic range of 0.005–0.388 mmol/L and a detection limit of 1.0 nmol/L was obtained using square wave voltammetry. The experimental data showed that the detection limit of methyldopa and peak separation from interfering compounds such as ascorbic acid(AA) and uric acid(UA) were improved using the proposed procedure. The method was successfully applied for the determination of methyldopa in pharmaceuticals.     

多壁碳纳米管表面熊果酸印迹聚合物的制备及固相萃取

以聚乙烯醇修饰的多壁碳纳米管(MWCNTs)为基材,熊果酸(UA)为模板分子,甲基丙烯酸(MAA)为功能单体,乙二醇二甲基丙烯酸酯(EGDMA)为交联剂,采用表面印迹技术在碳纳米管表面合成对熊果酸具有良好选择性的分子印迹聚合物( MWCNTs-MIPs).讨论了不同摩尔比例的功能单体与模板分子合成印迹聚合物的效果,得出...     

Selective Electrochemical Determination of Uric Acid in the Presence of Ascorbic Acid Using a Carbon Paste Electrode Modified with β‐Cyclodextrin

Uric acid (UA) was determined in the presence of ascorbic acid (AA) by using a carbon paste electrode modified superficially by a β‐cyclodextrin film (CPE/β‐CD). The surface carbon paste electrode was prepared applying a 30 cycles potential program and using a 1 M HClO₄+0.01 M β‐CD electrolytic solution. The UA and AA solutions were used to evaluate the electrode selectivity and sensitivity by cyclic voltammetric and amperometric methods. In these experiments the detection limit for UA was (4.6±0.01)×10^?6 M and the RSD calculated from the amperometric curves was 10%. From the data obtained it was possible to quantify UA in the urine and saliva samples. Selective detection of UA was improved by formation of an inclusion complex between β‐CD and UA. The results show that the CPE/β‐CD is a good candidate due to its selectivity and sensitivity in the UA determination in complex samples like the biological fluids.     

Quantification of Quercetin Using Glassy Carbon Electrodes Modified with Multiwalled Carbon Nanotubes Dispersed in Polyethylenimine and Polyacrylic Acid

This work reports the highly sensitive detection of quercetin using glassy carbon electrodes modified with multiwall carbon nanotubes (MWCNT) dispersed in polyethylenimine and poly(acrylic acid). The adsorptive stripping with square wave voltammetric transduction allowed the detection of 7.5 nM quercetin after 1.0 min accumulation at open circuit potential. The amperometric detection at 0.150 V is reported as an easier and simpler alternative to determine quercetin, with detection limits of 0.2 µM. The careful selection of the working conditions also made possible the detection of submicromolar levels of quercetin in the presence of excess of rutin. The proposed methodology was successfully used to quantify quercetin in onion samples.     

Electrocatalytic Oxidation of Glucose at Carbon Nanotubes Supported PtRu Nanoparticles and Its Detection

PtRu nanoparticles were supported on multiwall carbon nanotubes (MWNTs), which were further fabricated as an electrode for nonenzymatic glucose sensing. Transmission electron microscope and X‐ray diffraction patterns were used for characterization of the PtRu nanoparticles on MWNTs. Cyclic voltammetry and chronopotentiometry were applied to investigate the performance of the PtRu/MWNTs nanocomposite electrode for nonenzymatic oxidation of glucose. The PtRu/MWNTs electrode shows high electrocatalytic activity towards the oxidation of glucose in 0.1 M NaOH solution and thus can be used to selectively detect glucose. Under the optimal potential (+0.55 V vs. Ag/AgCl), the biosensor effectively performs a selective electrochemical analysis of glucose in the presence of common interferents, such as ascorbic acid (AA), dopamine (DP) and uric acid (UA). Wide linear calibration ranging from 1 mM to 15 mM, high sensitivity of 28.26 μA cm^?2 mM^?1, low detection limit of 2.5×10^?5 M, and fast response time of 10 s were achieved for the detection of glucose at the PtRu/MWNTs electrode.     

Selective and Simultaneous Voltammetric Determination of Glutathione,Uric Acid and Penicillamine by a Modified Carbon Nanotube Paste Electrode

In this paper, the use of a carbon paste electrode (CPE) modified by (E)‐3‐((2‐(2,4‐dinitrophenyl)hydrazono)methyl)benzene‐1,2‐diol (DHB) and carbon nanotubes (CNTs) for the determination of glutathione (GSH), uric acid (UA) and penicillamine (PA) is described. Initially, cyclic voltammetry was used to investigate the redox properties of the modified electrode in phosphate buffer. Next, the electrocatalytic oxidation of GSH via EC′ mechanism at the modified electrode was described. At the optimum pH of 7.0, the oxidation of GSH occurs at a potential that is 530 mV less positive than that of an unmodified carbon paste electrode. The values of the diffusion coefficient (D=2.5×10^?6 cm² s^?1) and the catalytic rate constant (k=1.7×10³ M^?1 s^?1) were calculated for GSH, using chronoamperometry. Based on differential pulse voltammetry, the oxidation of GSH exhibited a dynamic range between 0.4 and 700.0 µM and a detection limit (3σ) of 70.0 nM. Also, simultaneous determination of GSH, UA and PA was described at the modified electrode. Finally, this method was used for the determination of these substances in synthetic solutions and blood serum samples.     

Aptasensor for Thrombin Based on Carbon Nanotubes‐Methylene Blue Composites

The amperometric and EQCM aptasensors based on DNA aptamers immobilized by avidin‐biotin method or by electrostatic adsorption onto multiwalled carbon nanotube layer contained methylene blue (MB) have been developed and examined for thrombin detection in buffer and in spiked blood serum. The presence of MB increases the binding capacity of the surface layer and enhances the range of thrombin concentrations to be determined. This results in significant improvement of analytical characteristics of thrombin detection. The EQCM aptasensors allowed us to detect 0.3–100 nM and amperometric aptasensors 10–1000 nM of thrombin.     

Simultaneous Determination of Ascorbic Acid,Dopamine and Uric Acid at Pt Nanoparticles Decorated Multiwall Carbon Nanotubes Modified GCE

A modified electrode was fabricated by electrochemically deposition of Pt nanoparticles on the multiwall carbon nanotube covered glassy carbon electrode (Pt nanoparticles decorated MWCNT/GCE). A higher catalytic activity was obtained to electrocatalytic oxidation of ascorbic acid, dopamine, and uric acid due to the enhanced peak current and well‐defined peak separations compared with both, bare and MWCNT/GCE. The electrode surfaces were characterized by scanning electron microscopy (SEM), X‐ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS). Individual and simultaneous determination of AA, DA, and UA were studied by differential pulse voltammetry. The detection limits were individually calculated for ascorbic acid, dopamine, and uric acid as being 1.9×10^?5 M, 2.78×10^?8 M, and 3.2×10^?8 M, respectively. In simultaneous determination, LODs were calculated for AA, DA, and UA, as of 2×10^?5 M, 4.83×10^?8 M, and 3.5×10^?7 M, respectively.     

聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰的玻碳电极同时检测尿酸、黄嘌呤与次黄嘌呤

采用滴涂法得到多壁碳纳米管(MWCNTs)修饰的玻碳电极(GCE),通过电沉积方法将3-氨基-5-巯基-1,2,4-三唑(TA)沉积在MWCNTs/GCE表面,制备了聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰电极(p TA/MWCNTs/GCE)。采用循环伏安法(CV)和示差脉冲伏安法(DPV),研究了尿酸(UA)、黄嘌呤(XA)和次黄嘌呤(HX)在该修饰电极上的电化学行为。结果表明,该修饰电极对UA、XA和HX均有较好的电催化活性作用,能实现对3种物质的同时测定。UA、XA和HX在该修饰电极上的线性范围分别为9.0~739.0、2.0~259.0、1.0~353.0μmol/L;检出限分别为0.67、0.17、0.33μmol/L。该修饰电极已成功用于尿液和血清实际样品中UA、XA和HX的同时测定,回收率为98.8%~105.5%。     

Comparative study of multi walled carbon nanotubes-based electrodes in micellar media and their application to micellar electrokinetic capillary chromatography

This work reports on a comparative study of the electrochemical performance of carbon nanotubes-based electrodes in micellar media and their application for amperometric detection in micellar electrokinetic capillary chromatography (MEKC) separations. These electrodes were prepared in two different ways: immobilization of a layer of carbon nanotubes dispersed in polyethylenimine (PEI), ethanol or Nafion onto glassy carbon electrodes or preparation of paste electrodes using mineral oil as binder. Scanning electron microscopy (SEM) was employed for surface morphology characterization while cyclic voltammetry of background electrolyte was used for capacitance estimation. The amperometric responses to hydrogen peroxide, amitrol, diuron and 2,3-diclorophenol (2,3CP) in the presence and in the absence of sodium dodecylsulphate (SDS) were studied by flow injection analysis (FIA), demonstrating that the electrocatalytic activity, background current and electroanalytical performance were strongly dependent on the electrodes preparation procedure. Glassy carbon electrodes modified with carbon nanotubes dispersed in PEI (GC/(CNT/PEI)) displayed the most adequate performance in micellar media, maintaining good electrocatalytic properties combined with acceptable background currents and resistance to passivation. The advantages of using GC/(CNT/PEI) as detectors in capillary electrophoresis were illustrated for the MEKC separations of phenolic pollutants (phenol, 3-chlorophenol, 2,3-dichlorophenol and 4-nitrophenol) and herbicides (amitrol, asulam, diuron, fenuron, monuron and chlortoluron).     

Determination of Ascorbic Acid in the Presence of Uric Acid and Folic Acid by a Nanostructured Electrochemical Sensor Based on a TiO2 Nanoparticle Carbon Paste Electrode

A carbon paste electrode (CPE), modified with novel hydroquinone/TiO₂ nanoparticles, was designed and used for simultaneous determination of ascorbic acid (AA), uric acid (UA) and folic acid (FA). The magnitude of the peak current for modified TiO₂-nanoparticle CPE (MTNCPE) increased sharply in the presence of ascorbic acid and was proportional to its concentration. A dynamic range of 1.0–1400.0 μM, with the detection limit of 6.4 × 10^?7 M for AA, was obtained using the DPV technique (pH = 7.0). The prepared electrode was successfully applied for the determination of AA, UA, and FA in real samples.