Comparison of different extraction techniques for the determination of chlorinated pesticides in animal feed

The performances of Soxhlet extraction, dive-in Soxhlet extraction, microwave-assisted extraction (MAE), accelerated solvent extraction (ASE), fluidized-bed extraction (FBE), and ultrasonic extraction (UE) for the analysis of organochlorine pesticides in animal feed have been investigated. ASE and MAE provided significantly better extraction efficiency than Soxhlet extraction. The concentrations were 126.7 and 114.8%, respectively, of the values obtained by classical Soxhlet extraction, whereas the results from FBE and dive-in Soxhlet were comparable with those from the standard Soxhlet procedure. The reproducibility of FBE was the best, with RSDs ranging from 0.3 to 3.9%. Under the investigated operation conditions UE was not efficient, with the recoveries of target compounds being about 50% less than Soxhlet. Additionally, the performances of Soxhlet, dive-in Soxhlet, MAE, ASE and FBE were validated by determination of the certified reference material BCR-115. The results from the extraction techniques were in good agreement with the certified values.     

Influence of extraction methodologies on the analysis of five major volatile aromatic compounds of citronella grass (Cymbopogon nardus) and lemongrass (Cymbopogon citratus) grown in Thailand

This paper deals with the systematic comparison of extraction of major volatile aromatic compounds (VACs) of citronella grass and lemongrass by classical microhydrodistillation (MHD), as well as modern accelerated solvent extraction (ASE). Sixteen VACs were identified by GC/MS. GC-flame ionization detection was used for the quantification of five VACs (citronellal, citronellol, geraniol, citral, and eugenol) to compare the extraction efficiency of the two different methods. Linear range, LOD, and LOQ were calculated for the five VACs. Intraday and interday precisions for the analysis of VACs were determined for each sample. The extraction recovery, as calculated by a spiking experiment with known standards of VACs, by ASE and MHD ranged from 64.9 to 91.2% and 74.3 to 95.2%, respectively. The extraction efficiency of the VACs was compared for three solvents of varying polarities (hexane, dichloromethane, and methanol), seven different temperatures (ranging from 40 to 160 degrees C, with a gradual increment of 20 degrees C), five time periods (from 1 to 10 min), and three cycles (1, 2, and 3 repeated extractions). Optimum extraction yields of VACs were obtained when extractions were carried out for 7 min with dichloromethane and two extraction cycles at 120 degrees C. The results showed that the ASE technique is more efficient than MHD, as it results in improved yields and significant reduction in extraction time with automated extraction capabilities.     

RP-HPTLC densitometric determination and validation of vanillin and related phenolic compounds in accelerated solvent extract of Vanilla planifolia*

A simple, fast and sensitive RP-HPTLC method is developed for simultaneous quantitative determination of vanillin and related phenolic compounds in ethanolic extracts of Vanilla planifolia pods. In addition to this, the applicability of accelerated solvent extraction (ASE) as an alternative to microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE) and Soxhlet extraction was also explored for the rapid extraction of phenolic compounds in vanilla pods. Good separation was achieved on aluminium plates precoated with silica gel RP-18 F(254S) in the mobile phase of methanol/water/isopropanol/acetic acid (30:65:2:3, by volume). The method showed good linearity, high precision and good recovery of compounds of interest. ASE showed good extraction efficiency in less time as compared to other techniques for all the phenolic compounds. The present method would be useful for analytical research and for routine analysis of vanilla extracts for their quality control.     

Application of accelerated solvent extraction coupled with high-performance counter-current chromatography to extraction and online isolation of chemical constituents from Hypericum perforatum L

Accelerated solvent extraction (ASE) coupled with high-performance counter-current chromatography (HPCCC) was successfully used for the extraction and online isolation of five chemical constituents from the plant Hypericum perforatum L. The upper phase of the solvent system of ethyl acetate-methanol-water (5:2:5, v:v:v) was used as both the ASE solvent and the HPCCC stationary phase. Two hydrophobic compounds including 28.4 mg of hyperforin with a HPLC purity of 97.28% and 32.7 mg of adhyperforin with a HPLC purity of 97.81% were isolated. The lower phase of ethyl acetate-methanol-n-butanol-water (5:2:2.5:12, v:v:v:v) was used as both the ASE solvent and CCC stationary phase. Three hydrophilic compounds of 12.7 mg of 3,4,5-O-tricaffeoylquinic acid with a HPLC purity of 98.82%, 15.2 mg of 1,3,5-O-tricaffeoylquinic acid with a HPLC purity of 99.46% and 42.5mg of 3-O-caffeoylquinic acid with a HPLC purity of 96.90%, were obtained in a one-step extraction-separation process with less than 3h from 10.02 g of raw material of H. perforatum. The targeted compounds isolated, collected and purified by HPCCC were analyzed by high performance liquid chromatography (HPLC), the chemical structures of all five compounds above mentioned were identified by UV, MS and NMR.     

固相微萃取/加速溶剂萃取-气相色谱-质谱法分析青山绿水茶叶的挥发性成分

采用固相微萃取(SPME)和加速溶剂萃取(ASE)两种前处理方法从青山绿水茶叶(也叫苦丁茶)中提取挥发性成分,用气相色谱-质谱法(GC-MS)定性。实验结果表明:两种前处理方法共检测出91种成分,SPME检出49种,ASE检出56种,共同组分14种。青山绿水茶叶的挥发性成分主要成分有β-月桂烯、3,3,5-三甲基-1,5-庚二烯、L-柠檬烯、α-罗勒烯、β-罗勒烯、β-蒎烯、2-甲基安息香醛和5-羟甲基糠醛等物质。这两种提取方法各具优势,共同应用可以起到取长补短的作用。     

Microwave-assisted extraction and accelerated solvent extraction with ethyl acetate-cyclohexane before determination of organochlorines in fish tissue by gas chromatography with electron-capture detection

Focused open-vessel microwave-assisted extraction (FOV-MAE), closed-vessel microwave-assisted extraction (CV-MAE), and accelerated solvent extraction (ASE) were used for extraction before determination of organochlorine compounds (polychlorinated biphenyls, DDT, toxaphene, chlordane, hexachlorobenzene, hexachlorocyclohexanes, and dieldrin) in cod liver and fish fillets. Wet samples were extracted without the time-consuming step of lyophilization or other sample-drying procedures. Extractions were performed with the solvent mixture ethyl acetate-cyclohexane (1 + 1, v/v), which allowed direct use of gel-permeation chromatography without solvent exchange. For FOV-MAE, the solvent mixture removed water from the sample matrix via azeotropic distillation. The status of water removal was controlled during extraction by measuring the temperature of the distillate. After water removal, the temperature of the distillate increased and the solvent mixture became less polar. Only the pure extraction solvent allowed quantitative extraction of the organochlorine compounds. For CV-MAE, water could not be separated during the extraction. For this reason, the extraction procedure for wet fish tissue required 2 extraction steps: the first for manual removal of coextracted water, and the second for quantitative extraction of the organochlorine compounds with the pure solvent. Therefore, CV-MAE is less convenient for samples with high water content. For ASE, water in the sample was bound with Na2SO4. The reproducibility for each technique was very good (relative standard deviation was typically <10%); the slightly varying levels were attributed to deviations during sample cleanup and the generally low levels.     

加速溶剂提取凝胶渗透色谱净化气相色谱质谱快速测定玉米中多环芳烃

研究了玉米中16种多环芳烃的快速分析方法.采用加速溶剂萃取法(ASE)对玉米样品进行提取,提取溶剂为二氯甲烷,萃取池中依次加入3 g中性氧化铝吸附剂和10 g待测样品,提取的同时能够在线净化除去小分子杂质.收集的提取液进一步用凝胶渗透色谱(GPC)除去样品中大分子油脂和色素,流动相为二氯甲烷,流速为3 mL/min,收集9～13 min的流出液,提取液浓缩定容至1 mL后用GC-SIM-MS进行分析.16种 PAHs以及4种替代物在2个浓度水平添加时的平均添加回收率在55.7%～145.3%之间; RSD为1 4%～16.8%;方法检出限为0.005～0.120 ng/g.本方法简便、快速、准确,净化效果较好,满足残留分析的要求,且能应用于其它谷物样品的日常分析.     

加速溶剂萃取法快速提取黄连中的生物碱

探讨了快速溶剂萃取法（ASE）提取黄连中生物碱的可行性,并比较了该方法与回流提取法和超声提取法的优越性。以黄连中盐酸小檗碱的提取率为指标,以高效液相色谱法（HPLC）为检测方法,用正交实验对快速溶剂萃取法从黄连中提取盐酸小檗碱的工作条件进行优化。最佳仪器参数：提取溶剂为80%乙醇＋0.5%HCl,提取温度为130℃,静态提取时间为10 min,提取次数为1次。快速溶剂萃取法可作为黄连中生物碱分析测定的前处理方法。     

Identification of organic sulfur compounds in coal bitumen obtained by different extraction techniques using comprehensive two-dimensional gas chromatography coupled to time-of-flight mass spectrometric detection

The determination of organic sulfur compounds (OSC) in coal is of great interest. Technically and operationally these compounds are not easily removed and promote corrosion of equipment. Environmentally, the burning of sulfur compounds leads to the emission of SO _x gases, which are major contributors to acid rain. Health-wise, it is well known that these compounds have mutagenic and carcinogenic properties. Bitumen can be extracted from coal by different techniques, and use of gas chromatography coupled to mass spectrometric detection enables identification of compounds present in coal extracts. The OSC from three different bitumens were tentatively identified by use of three different extraction techniques: accelerated solvent extraction (ASE), ultrasonic extraction (UE), and supercritical-fluid extraction (SFE). Results obtained from one-dimensional gas chromatography (1D GC) coupled to quadrupole mass spectrometric detection (GC–qMS) and from two-dimensional gas chromatography with time-of-flight mass spectrometric detection (GC × GC–TOFMS) were compared. By use of 2D GC, a greater number of OSC were found in ASE bitumen than in SFE and UE bitumens. No OSC were identified with 1D GC–qMS, although some benzothiophenes and dibenzothiophenes were detected by use of EIM and SIM modes. GC × GC–TOFMS applied to investigation of OSC in bitumens resulted in analytical improvement, as more OSC classes and compounds were identified (thiols, sulfides, thiophenes, naphthothiophenes, benzothiophenes, and benzonaphthothiophenes). The roof-tile effect was observed for OSC and PAH in all bitumens. Several co-elutions among analytes and with matrix interferents were solved by use of GC×GC.     

Application of accelerated solvent extraction to the investigation of saikosaponins from the roots of Bupleurum falcatum

Accelerated solvent extraction (ASE) was applied to the extraction of saikosaponin a, saikosaponin c and saikosaponin d from the roots of Bupleurum falcatum. Main extraction parameters such as the extraction solvents, extraction temperature and static extraction time were investigated and optimized. The optimized procedure employed 70% methanol as extraction solvent, 120°C of extraction temperature, 10 min of static extraction time, 60% of flush volume and the extraction recoveries of the three compounds were near to 100% with one extraction cycle. The extracted samples were analyzed by HPLC with UV detector. The HPLC conditions were as follows: Hypersil ODS2 (4.6 mm×250 mm, 5 μm) column, acetonitrile and water as mobile phase, flow rate of 1.0 mL/min, UV detection wavelength of 204 nm and injection volume of 20 μL. Compared with the traditional methods including heat‐reflux extraction and ultrasonic‐assisted extraction, the proposed ASE method was more efficient and faster to be operated. The results indicated that ASE was an alternative method for extracting saikosaponins from the roots of B. falcatum.     

快速溶剂萃取柚皮中的黄酮类化合物

采用快速溶剂萃取法从柚子皮中提取出黄酮类化合物,考察了不同的提取溶剂、提取时间、提取温度、循环次数等提取条件下的提取效果,并与微波法、超声波法及索氏提取法进行了对比.结果表明,快速溶剂萃取法提取柚子皮中的黄酮类化合物,在提取溶剂用量、提取时间和提取效率等方面,均优于传统的提取方法,且自动化程度高,为进一步开发利用柚子皮的药用价值提供了参考.     

Optimization and comparison of MAE, ASE and Soxhlet extraction for the determination of HCH isomers in soil samples

The microwave-assisted extraction (MAE), accelerated solvent extraction (ASE) and Soxhlet extraction of two isomers of hexachlorocyclohexane, alpha-HCH and gamma-HCH, from a polluted landfill soil have been optimized following different experimental designs. In the case of microwave-assisted extraction, the following variables were considered: pressure, extraction time, microwave power, percentage of acetone in n-hexane mixture and solvent volume. When ASE extraction was studied the variables were pressure, temperature and extraction time. Finally, the percentage of acetone in n-hexane mixture and the extraction time were the only variables studied for Soxhlet extraction. The concentrations obtained by the three extraction techniques were, within their experimental uncertainties, in good agreement. This fact assures the possibility of using both ASE and MAE techniques in the routine determination of lindane in polluted soils and sediments.     

Determination of organochlorine pesticides and chlorobenzenes in strawberries by using accelerated solvent extraction combined with sorptive enrichment and gas chromatography/mass spectrometry

An analytical scheme for the determination of several organochlorine pesticides like hexachlorocyclohexanes (HCHs) and DDX compounds (p,p'-DDE, p,p'-DDD, and p,p'-DDT) as well as chlorobenzenes in strawberries has been developed. The procedure is based on aqueous accelerated solvent extraction (ASE) followed by solid-phase microextraction (SPME) or stir bar sorptive extraction (SBSE) and subsequent thermodesorption-gas chromatography/mass spectrometry analysis. A 65 microm polydimethylsiloxane/ divinylbenzene fiber was chosen for the SPME experiments. Significant SPME and ASE parameters were optimized using spiked water and strawberry samples. For the ASE of the organochlorine compounds, a water-acetone mixture (90 + 10, v/v) as the extraction solvent, an extraction temperature of 120 degrees C, and 2 cycles of 10 min extraction proved optimal. The developed method was evaluated with respect to precision and limits of detection (LOD). The relative standard deviations of replicate ASE-SPME determinations (n = 5) were in the range of 4-24%. LOD values between 1 and 10 microg/kg were achieved with the exception of DDT and DDE (40 microg/kg). Using SBSE, the LOD of these compounds could be improved (2 and 5 microg/kg). The main advantages of this method are the avoidance of cleanup and concentration procedures as well as the significant reduction of the required volume of organic solvents. The described method was applied to the determination of the pollutants in strawberry samples collected from different allotment gardens in a potentially polluted area, the Bitterfeld-Wolfen region (Germany).     

Accelerated solvent extraction of fluometuron from selected soils

Accelerated solvent extraction (ASE) is a recently developed extraction technique that is more rapid and produces less waste than do conventional liquid/liquid extraction methods. Optimal conditions were determined for ASE of fluometuron from 2 Weswood clay loam soils. Two solvents (acetonitrile and methanol), 2 temperatures (50 and 100 degrees C), and the number of static cycles (1, 2, and 3) were evaluated. The most efficient and reproducible extractions were obtained when methanol was combined with a 50 degrees C extraction temperature and the static cycle was repeated 3 times. These experiments indicated that existing extraction methods for fluometuron can easily be adapted for ASE.     

Determination of polycyclic aromatic hydrocarbons in marine sediments using a new ASE-SFE extraction technique

In order to determine PAHs in marine sediment samples by GC/MS(SIM) a new extraction approach of ASE-SFE was evaluated using combined accelerated solvent extraction (ASE, dynamic and static mode) and supercritical fluid extraction (SFE, dynamic mode) without further purification of the sample. The solvents used for ASE-SFE were methylene chloride and carbon dioxide. The recovery data, precision and accuracy of the whole method were evaluated statistically. The average recoveries of PAHs, based on deuterated internal standards were 77% for 2-3-ring PAHs, 85% for 4-ring PAHs, 88% for 5-ring PAHs and 97% for 6-ring PAHs. The extraction time required for the ASE-SFE technique was 30 min, which is longer than in the case of independent use of ASE and shorter compared to SFE. ASE-SFE recoveries of PAHs from SRM marine sediment are comparable for (2-3-ring, 4-ring PAHs) or higher (5-ring, 6-ring PAHs) than reported for the conventional extraction methods of ASE and SFE. Method detection limits of (MDL) were statistically estimated. MDL values obtained for 15 PAHs compounds vary between 0.06 ngg(-1) and 3.54 ngg(-1).     

Evaluation of Soxhlet extraction, accelerated solvent extraction and microwave-assisted extraction for the determination of polychlorinated biphenyls and polybrominated diphenyl ethers in soil and fish samples

Three commonly applied extraction techniques for persistent organic chemicals, Soxhlet extraction (SE), accelerated solvent extraction (ASE) and microwave-assisted extraction (MAE), were applied on soil and fish samples in order to evaluate their performances. For both PCBs and PBDEs, the two more recent developed techniques (ASE and MAE) were in general capable of producing comparable extraction results as the classical SE, and even higher extraction recoveries were obtained for some PCB congeners with large octanol-water partitioning coefficients (K_ow). This relatively uniform extraction results from ASE and MAE indicated that elevated temperature and pressure are favorable to the efficient extraction of PCBs from the solid matrices. For PBDEs, difference between the results from MAE and ASE (or SE) suggests that the MAE extraction condition needs to be carefully optimized according to the characteristics of the matrix and analyte to avoid degradation of higher brominated BDE congeners and improve the extraction yields.     

加速溶剂萃取技术在中药有效成分分析中的应用

以两种药材为研究实例,对加速溶剂萃取法（ASE）在中药材有效成分提取研究中的应用进行了简要介绍。采用正交试验法考察了提取丹参中丹酚酸B的提取条件（萃取温度、静态萃取时间、萃取溶剂以及料液比）,确定了较好的实验条件。比较了ASE、水蒸气蒸馏法、超声波提取法及索氏提取法对木香挥发油的提取效果,结果表明ASE对木香挥发油的提取效果最好。     

Extraction of Phenolic Compounds from Fresh Apple Pomace by Different Non-Conventional Techniques

Red Delicious apple pomace was produced at laboratory scale with a domestic blender and different non-conventional extraction techniques were performed to isolate phenolic compounds, such as ultrasound-assisted extraction (UAE), ultraturrax extraction (UTE), accelerated solvent extraction (ASE) and pulsed electric field (PEF) extraction pre-treatment. Total phenolic content (TPC) was determined by Folin–Ciocalteu assay. Phloridzin, the main phenolic compound in apples, was determined by chromatographic analysis Q-TOF-LC/MS. The results obtained with these techniques were compared in order to identify the most efficient method to recover polyphenols. The highest value of TPC (1062.92 ± 59.80 µg GAE/g fresh apple pomace) was obtained when UAE was performed with EtOH:H₂O (50:50, v/v), while ASE with EtOH:H₂O (30:70, v/v) at 40 °C and 50% of flush was the most efficient technique in the recovery of phloridzin. The concentration of the main phenolic compounds ranged from 385.84 to 650.56 µg/g fresh apple pomace. The obtained results confirm that apple pomace represents an interesti-ng by-product, due to the presence of phenolic compounds. In particular, phloridzin could be considered a biomarker to determine the quality of numerous apple products. Therefore, this research could be a good starting point to develop a value-added product such as a functional food or nutraceutical.     

Extraction and detection of arsenicals in seaweed via accelerated solvent extraction with ion chromatographic separation and ICP-MS detection

An accelerated solvent extraction (ASE) device was evaluated as a semi-automated means of extracting arsenicals from ribbon kelp. The effect of the experimentally controllable ASE parameters (pressure, temperature, static time, and solvent composition) on the extraction efficiencies of arsenicals from seaweed was investigated. The extraction efficiencies for ribbon kelp (approximately 72.6%) using the ASE were fairly independent (< 7%) of pressure, static time and particle size after 3 ASE extraction cycles. The optimum extraction conditions for the ribbon kelp were obtained by using a 3 mL ASE cell, 30/70 (w/w) MeOH/H2O, 500 psi (1 psi = 7 KPa), ambient temperature, 1 min heat step, 1 min static step, 90% vol. flush, and a 120 s purge. Using these conditions, two other seaweed products produced extraction efficiencies of 25.6% and 50.5%. The inorganic species present in the extract represented 62.5% and 27.8% of the extracted arsenic. The speciation results indicated that both seaweed products contained 4 different arsenosugars, DMA (dimethylarsinic acid), and As(V). One seaweed product also contained As(III). Both of these seaweed products contained an arsenosugar whose molecular weight was determined to be 408 and its structure was tentatively identified using ion chromatography-electrospray ionization-mass spectrometry/mass spectrometry (IC-ESI-MS/MS).     

Characterization of secondary volatile profiles in Nigella sativa seeds from two different origins using accelerated solvent extraction and gas chromatography-mass spectrometry

The extraction and identification of bioactive compounds from herbs is of great interest. In this study, accelerated solvent extraction (ASE) technique was used to analyze the secondary volatile profiles in Nigella sativa seeds obtained from two different origins, Egypt and Bangladesh. The main extraction parameters, including extraction temperature, pressure and static extraction time, were investigated and optimized. Identification and quantification of the major constituents in nonpolar extracts (hexane) were achieved by means of GC‐FID/GC‐MS analysis with external standards. The two seeds showed a similar variety of chemical composition; however, the secondary volatiles profile of Bangladesh seed was higher than that of the Egyptian seed. A total of 25 compounds were identified from the ASE extract under the following optimum extraction conditions: 100°C, 1500 psi and 5 min, for extraction temperature, pressure and static time, respectively. The proposed technique can be used for the characterization of N. sativa varieties or cultivars. Copyright © 2012 John Wiley & Sons, Ltd.