H2在K0-MWCNTs上储存和吸附/脱附特性研究

利用高压容积法辅以卸压升温脱附排水法, 测定金属K修饰多壁碳纳米管对H₂的吸附储存容量. 结果表明, 在室温(25 ℃), 7.25 MPa实验条件下, x%K⁰-MWCNTs (x%＝30%～35%, 质量百分数)对H₂的吸附储存容量可达3.80 wt%(质量百分数), 是相同条件下单纯MWCNTs氢吸附储量的2.5倍; 室温下卸至常压的脱附氢量为3.36 wt%(占总吸附氢量的～88%), 后续升温至673 K的脱附氢量为0.41 wt%(占总吸附氢量的～11%). 利用LRS和H₂-TPD-GC/MS等谱学方法对H₂/K⁰-MWCNTs吸附体系的表征研究表明, H₂在K⁰-MWCNTs上吸附存在非解离 (即分子态)和解离(即原子态)两种吸附态; 在≤723 K温度下, H₂/K⁰-MWCNTs体系的脱附产物几乎全为H₂气; 723 K以上高温脱附产物不仅含H₂, 也含有CH₄, C₂H₄和C₂H₂等C₁/C₂-烃.     

Effect of titanium based complex catalyst and carbon nanotubes on hydrogen storage performance of magnesium

Mg (MgH₂)-based composites, using carbon nanotubes (CNTs) and pre-synthesized titanium based complex (TCat) as the catalysts, were prepared by high energy ball milling technique. The use of both catalysts demonstrated markedly improved the hydrogen storage performance, e.g. a significant increase of hydrogen release rate and decrease of desorption temperature. The synthesized composites can absorb almost 6 wt% of hydrogen within 3 min at 200 °C and desorb 6 wt% hydrogen in 10 min at 310 °C. The influence of CNTs and TCat on desorption temperature was also investigated by using temperature programmed desorption (TPD). The TPD results reveal that the peak desorption temperature and the onset temperature can be lowered by 109 °C and 155 °C, respectively, compared to the non-catalyzed MgH₂. The reaction enthalpy and entropy of hydrogen desorption for the synthesized MgH₂-based composites are calculated by the van’t Hoff analysis to be 73.1 kJ/mol H₂ and 130.2 J/mol H₂ K, respectively.     

Pre-Eutectic Densification of Calcium Carbonate Doped with Lithium Carbonate

Pressureless sintering of CaCO₃ was carried out, with Li₂CO₃ (from 0.5 to 8 wt%) as an additive, under different pressures of CO₂. Densification occurs between 600 and 700°C. Sintering above the eutectic temperature (T>662°C) leads to the decomposition of calcium carbonate and the materials become expanded. At 620° under 1 kPa of CO₂, a relative density of 96% is reached. Li₂CO₃ enhances the densification process and grain growth of calcium carbonate. CO₂ pressure slows down densification and grain growth kinetics. These results are explained by the influence of carbonate and calcium ion vacancies on the sintering mechanisms. This revised version was published online in August 2006 with corrections to the Cover Date.     

Enhanced electrochemical performance of submicron LiCoO<Subscript>2</Subscript> synthesized by polymer pyrolysis method

Submicron LiCoO₂ was synthesized by a polymer pyrolysis method using LiOH and Co(NO₃)₂ as the precursor compounds. Experimental results demonstrated that the powders calcined at 800 °C for 12 h appear as well-crystallized, uniform submicron particles with diameter of about 200 nm. As a result, the as-prepared LiCoO₂ electrode displayed excellent electrochemical properties, with an initial discharge capacity of 145.5 mAh/g and capacity retention of 86.1% after 50 cycles when cycled at 50 mA/g between 3.5 and 4.25 V. When cycled between 3.5 and 4.5 V, the discharge capacity increased to 177.9 mAh/g with capacity retention of 85.6% after 50 cycles.     

Carbon nanostructures in an ammonium medium

The reaction of fullerene C₆₀, single- and multi-walled carbon nanotubes (SWNTs and MWNTs, respectively), as well as a mixture of these carbon nanomaterials with 8–10 wt% of ammonium chloride (reaction promoter) with ammonia as a source of hydrogen and nitrogen, at an initial ammonium pressure of 0.6–0.8 MPa in the temperature range 20–550°C was studied. The reaction at 450°C is accompanied by hydrogenation and nitrogenation of the fullerite matrix, and at 500°C decomposition of the fullerene carcass occurs. Physicochemical properties of the hydride-nitride phases formed by the reaction were studied. Single- and multiwalled nanotubes were shown to be stable in an ammonium medium at 20–450°C, while at 500°C their ends are opened.     

Nanocrystalline nickel cobalt hydroxides/ultrastable Y zeolite composite for electrochemical capacitors

A novel nanocomposite of Co(OH)₂−Ni(OH)₂ and ultrastable Y molecular sieves was synthesized by an improved chemical precipitation method for electrochemical capacitors. The Co(OH)₂−Ni(OH)₂/ultrastable Y zeolite (USY) composite and its microstructure were characterized by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. Electrochemical characterization was performed by cyclic voltammetry and galvanostatic charge–discharge measurements. The results show that Co(OH)₂−Ni(OH)₂/USY microstructure applied for the electrochemical energy storage has displayed superior capacitive performance. The effect of heat treatment conditions on specific capacitance properties was also systemically explored. Upon annealing at 250 °C, the maximum specific capacitance was up to 479 F/g (or 1,710 F/g after correcting for the weight percent of Co(OH)₂−Ni(OH)₂ phase). Annealing temperatures higher than 250 °C may cause the hydroxide to form oxide phase and decrease the surface activity of the oxide, thereby leading to a decline of the specific capacitance.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Ni0.8Co0.15Al0.05C2O4@Graphene的合成及电化学性能研究

过渡金属氧化物/石墨烯复合材料具有优异的电化学性能被广泛应用在锂离子电池中。本文以硫酸镍、硫酸钴、硫酸铝、草酸为原料按一定的物质的量比配制成溶液,在120°C的条件下水热反应12小时,得到多元过渡金属氧化物前驱体Ni_0.8Co_0.15Al_0.05C₂O₄(NCA-C₂O₄);该前驱体经聚烯丙基胺盐酸盐修饰后,与氧化石墨烯进行复合并还原得到石墨烯包覆的多元过渡金属氧化物/石墨烯负极材料Ni_0.8Co_0.15Al_0.05C₂O₄@Graphene(NCA-C₂O₄@G)。对材料的结构、形貌和电化学性质进行了表征。扫描电镜测试结果显示样品粒度均一,具有两端不规则长方体形貌。电化学性能测试结果表明：石墨烯包覆后的NCA-C₂O₄@G充放电容量高于前驱体NCA-C₂O₄,NCA-C₂O₄@G复合材料在0.1C电流密度 (1C=1000 mAh/g)下首次放电比容量为1956 mA h/g;经过0.1C、0.2C、0.5C、1C、2C高倍率循环后,当测试电流密度恢复至100 mA/g时,复合材料比容量可迅速回升至720 mA h/g,并在随后50次循环中比容量保持稳定,显示出良好的循环稳定性和倍率性能。     

Dry Potassium-Based Sorbents for CO<Subscript>2</Subscript> Capture

Dry potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, CaO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property of various sorbents were measured in the presence of H₂O in a fixed bed reactor, during multiple cycles at various temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–400 °C). The KAlI30, KCaI30, and KMgI30 sorbents formed new structures such as KAl(CO₃)₂(OH)₂, K₂Ca(CO₃)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely convert to the original K₂CO₃ phase at temperatures below 200 °C, during the CO₂ absorption process in the presence of 9 vol.% H₂O. In the case of KACI30, KTiI30, and KZrI30, only a KHCO₃ crystal structure was formed during CO₂ absorption. The formation of active species, K₂CO₃·1.5H₂O, by the pretreatment with water vapor and the formation of the KHCO₃ crystal structure after CO₂ absorption are important factors for absorption and regeneration, respectively, even at low temperatures (130–150 °C). In particular, the KTiI30 sorbent showed excellent characteristics with respect to CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (87 mg CO₂/g sorbent) without the pretreatment with water vapor, unlike KACI30, and a fast and complete regeneration at a low temperature condition (1 atm, 150 °C). In addition, the higher total CO₂ capture capacity of KMgI30 (178.6 mg CO₂/g sorbent) than that of the theoretical value (95 mg CO₂/g sorbent) was explained through the contribution of the absorption ability of MgO support. In this review, we introduce the CO₂ capture capacities and regeneration properties of several potassium-based sorbents, the changes in the physical properties of the sorbents before/after CO₂ absorption, and the role of water vapor and its effects on CO₂ absorption.     

The Preparation and Characterization of La Doped TiO2 Nanotubes and Their Photocatalytic Activity

La-doped TiO₂ nanotubes (La/TiO₂ NTs) were prepared by the combination of sol-gel process with hydrothermal treatment. The prepared samples were characterized by using transmission electron microscopy, x-ray diffraction, x-ray photoelectron spectra, and ultraviolet-visible spectra. The photocatalytic performance of La/TiO₂ NTs was studied by testing the degradation rate of methyl orange under ultraviolet (UV) irradiation. The results indicated La/TiO₂ NTs calcined at 300°C consisted of anatase as the unique phase. The absorption spectra of the La/TiO₂ NTs showed a stronger absorption in the UV range and a slight red shift in the band gap transition than that of pure TiO₂ nanotubes. The photocatalytic performance of TiO₂ NTs could be improved by the doping of lanthanum ions, which is ascribed to several beneficial effects the formation of Ti-O-La bond and charge imbalance, existing of oxygen defects and Ti³⁺ species, stronger absorption in the UV range and a slight red shift in the band gap transition, as well as higher equilibrium dark adsorption of methyl orange. 0.75 wt% La/TiO₂ NTs had the best catalytic activity.     

共聚物模板辅助合成高倍率性能多孔Li2FeSiO4@C/CNTs纳米复合正极材料

通过溶胶-凝胶法制备了Li₂FeSiO₄@C/CNTs(LFS@C/CNTs)纳米复合材料,其中三嵌段共聚物P123用作结构导向剂和碳源,碳纳米管作为导电线提高材料的导电性。LFS@C/CNTs不仅具有海绵状纳米孔,能够与电解液充分接触改善锂离子的传输路径,同时由非晶碳和碳纳米管构成的三维桥联导电网络利于电子的快速传递,提高了材料大电流充放电能力和循环稳定性。复合后的LFS@C/CNTs的高倍率性能相比LFS@C明显提高, 当CNTs的掺量为4%,电压窗口为1.5~4.5 V,0.1C电流密度下放电比容量为182 mAh·g^-1。在10C经70次循环后该材料的放电比容量能保持在117 mAh·g^-1,是LFS@C放电比容量(55 mAh·g^-1)的两倍。     

The effect of annealing temperatures on surface properties,hydroxyapatite growth and cell behaviors of TiO2 nanotubes

Well‐ordered TiO₂ nanotubes were prepared by the electrochemical anodization of titanium in an ethylene glycol electrolyte containing 1 wt% NH₄F and 10 wt% H₂O at 20 V for 20 min, followed by annealing. The surface morphology and crystal structure of the samples were examined as a function of the annealing temperature by field emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD), respectively. Crystallization of the nanotubes to the anatase phase occurred at 450 °C, while rutile formation was observed at 600 °C. Disintegration of the nanotubes was observed at 600 °C and the structure vanished completely at 750 °C. Electrochemical corrosion studies showed that the annealed nanotubes exhibited higher corrosion resistance than the as‐formed nanotubes. The growth of hydroxyapatite on the different TiO₂ nanotubes was also investigated by soaking them in simulated body fluid (SBF). The results indicated that the tubes annealed to a mixture of anatase and rutile was clearly more efficient than that in their amorphous or plain anatase state. The in vitro cell response in terms of cell morphology and proliferation was evaluated using osteoblast cells. The highest cell activity was observed on the TiO₂ nanotubes annealed at 600 °C. Copyright © 2010 John Wiley & Sons, Ltd.     

共聚物模板辅助合成高倍率性能多孔Li2FeSiO4@C/CNTs纳米复合正极材料

通过溶胶-凝胶法制备了Li₂FeSiO₄@C/CNTs(LFS@C/CNTs)纳米复合材料,其中三嵌段共聚物P123用作结构导向剂和碳源,碳纳米管作为导电线提高材料的导电性。LFS@C/CNTs不仅具有海绵状纳米孔,能够与电解液充分接触改善锂离子的传输路径,同时由非晶碳和碳纳米管构成的三维桥联导电网络利于电子的快速传递,提高了材料大电流充放电能力和循环稳定性。复合后的LFS@C/CNTs的高倍率性能相比LFS@C明显提高, 当CNTs的掺量为4%,电压窗口为1.5~4.5 V,0.1C电流密度下放电比容量为182 mAh·g^-1。在10C经70次循环后该材料的放电比容量能保持在117 mAh·g^-1,是LFS@C放电比容量(55 mAh·g^-1)的两倍。     

The effect of nanolayer AlF<Subscript>3</Subscript> coating on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cycle life in high temperature for lithium secondary batteries

The surface of the spinel LiMn₂O₄ was coated with AlF₃ by a chemical process to improve its electrochemical performance at high temperatures. The morphology and structure of the original and AlF₃-coated LiMn₂O₄ samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM). All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. It was found that the surfaces of the original LiMn₂O₄ samples were covered with a nanolayer AlF₃ after the treatment. The charge/discharge of the materials were carried at 220 mA/g in the range of 3.0 and 4.4 V at 55°C. While the original LiMn₂O₄ showed 17.8% capacity loss in 50 cycles at 55°C, the AlF₃-coated LiMn₂O₄ (118.1 mA h/g) showed only 3.4% loss of the initial capacity (122.3 mA h/g) at 55°C. It is obvious that the improvement in cycling performance of the coated-LiMn₂O₄ electrode at 55°C is attributed to the presence of AlF₃ on the surface of LiMn₂O₄. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 817–819. The article is published in the original     

Hydrogen production from water decomposition by redox of Fe2O3 modified with single- or double-metal additives

Iron oxide modified with single- or double-metal additives (Cr, Ni, Zr, Ag, Mo, Mo-Cr, Mo-Ni, Mo-Zr and Mo-Ag), which can store and supply pure hydrogen by reduction of iron oxide with hydrogen and subsequent oxidation of reduced iron oxide with steam (Fe₃O₄ (initial Fe₂O₃)+4H₂↔3Fe+4H₂O), were prepared by impregnation. Effects of various metal additives in the samples on hydrogen production were investigated by the above-repeated redox. All the samples with Mo additive exhibited a better redox performance than those without Mo, and the Mo-Zr additive in iron oxide was the best effective one enhancing hydrogen production from water decomposition. For Fe₂O₃-Mo-Zr, the average H₂ production temperature could be significantly decreased to 276 °C, the average H₂ formation rate could be increased to 360.9-461.1 μmol min⁻¹ Fe-g⁻¹ at operating temperature of 300 °C and the average storage capacity was up to 4.73 wt% in four cycles, an amount close to the IEA target.     

Addition of TiO2 nanowires in different polymorphs for dye-sensitized solar cells

TiO₂ (B) and TiO₂ anatase nanowires were prepared at 150 °C for 120 h by a hydrothermal method followed by calcination in air at 400 °C for 2 h and at 700 °C for 2 h for TiO₂ (B) and TiO₂ anatase, respectively. Although dye-sensitized solar cells (DSC) with fully nanowire electrodes showed a rather low light-to-electricity conversion efficiency of 1.33 % for TiO₂ (B) and 2.42% for TiO₂ anatase, 10 wt % nanowire-dispersed electrodes in a P-25 TiO₂-nanoparticle matrix demonstrated improved efficiency of 6.17 % for TiO₂ (B) and 6.53% for TiO₂ anatase, these exceeding that of pure P-25 electrodes in this work (η=5.59%). The dominant mechanisms of the improvement at 10 wt% for the two different polymorphs are thought to be different, i.e., a light-scattering and film-thickness increment for the TiO₂ (B) system, whereas there is an improved conduction path through the matrix for the TiO₂ anatase system.      

稀土元素对R-Y-Ni系A2B7型无镁储氢合金微观结构和电化学性能的影响

采用真空电弧熔炼及退火处理制备R-Y-Ni系A_2B_7型R0.3Y0.7Ni3.25Mn0.15Al0.1(R=Y,La,Pr,Ce,Nd,Gd,Sm)储氢合金,系统研究稀土元素R对合金微观组织与结构、储氢和电化学性能的影响。XRD和SEM-EDS分析表明,合金退火组织由Ce2Ni7型主相、PuNi3型及少量Ca Cu5型相组成,Ce2Ni7型主相的晶格常数a、c及晶胞体积V均随稀土R原子半径的减小而依次降低。该合金均具有明显的吸放氢平台,常温下最大吸氢容量为1.17%~1.48%(w/w),吸氢平台压Peq为0.037~0.194 MPa。电化学分析表明,退火合金电极的电化学活化性能优良,R=La合金具有最高的放电容量(389.2 mAh·g-1)和较佳的容量保持率(充放电循环100次后的S100=85.7%),其中合金微观组织的不均匀性及稀土元素的电化学腐蚀是影响电极循环稳定性的主要原因。合金电极的高倍率放电性能(电流密度为900 m A·g-1)HRD900=71.05%~86.94%,其电极反应动力学控制步骤主要由氢原子在合金体相中的扩散速率所控制。     

High activity of novel Pd/TiO2 nanotube catalysts for methanol electro-oxidation

Electro-oxidation of methanol in sulfuric acid solution was studied using palladium well-dispersed on titanium nanotubes, in relation to methanol oxidation processes in the direct oxidation methanol fuel cell. Pd dispersed on titania nanotubes, which leads to high surface area substrates, showed excellent catalytic activities compared to those of pure Pd and Pd-TiO₂ nanoparticles. TEM results show a narrow distribution of TiO₂ nanoparticles whose particle size is about 10 nm, and uniform nano-sized TiO₂ nanotubes with 10 nm in diameters are seen from HRTEM . A homogeneous structure in the composite nanomaterials is indicated by XRD analysis. The composite electrode activities were measured by cyclic voltammetry (CV) and at 25 °C it was found that 3 wt% Pd in titania nanotubes had the best activity for methanol oxidation.     

Evaluation of polymeric nanocomposites for the detection of toxic gas analytes

Four different metal oxide nanoparticles, copper oxide (CuO), aluminum oxide (Al₂O₃), nickel oxide (NiO), and titanium dioxide (TiO₂), were added to poly (2,5-dimethyl aniline) (P25DMA) during synthesis to create different polymer nanocomposites. These polymer nanocomposites were evaluated as potential sensing materials for six different gas analytes (acetaldehyde, acetone, benzene, ethanol, formaldehyde, and methanol). It was found that CuO did not incorporate into the P25DMA and only a small percentage of Al₂O₃ was incorporated. However, both NiO and TiO₂ were incorporated into the P25DMA at the same concentration as during the synthesis step. Overall, the type of metal oxide significantly affected the morphology of the sensing material and the amount of each analyte sorbed. For example, P25DMA doped with 5 wt% Al₂O₃ had high selectivity towards ethanol, whereas P25DMA doped with 20 wt% TiO₂ sorbed the most ethanol. However, P25DMA doped with 20 wt% TiO₂ also sorbed a high amount of formaldehyde, making P25DMA doped with 20 wt% TiO₂ less selective than P25DMA doped with 5 wt% Al₂O₃ towards ethanol with respect to formaldehyde.     

Effect of Cu content on structure,hydrogen storage properties and electrode performance of LaNi4.1-x Co0.6Mn0.3Cu x alloys

The effect of Cu content on structure, hydrogen storage, and electrochemical properties of LaNi_4.1-x Co_0.6Mn_0.3Cu _x alloys has been investigated. For sample, A, B, C, and D are used to represent alloys (x?=?0, 0.15, 0.3, and 0.45), respectively. The results indicate that the four alloys are all single-phase alloy with LaNi₅ phase of CaCu₅ hexagonal structure, the hydrogen storage capacities of the alloy are about 1.49 wt% (A), 1.48 wt% (B), 1.43 wt% (C), and 1.25 wt% (D) at 303 K. With the increase of Cu content (x) from A to D, hydrogen desorption plateau pressure and pressure hysteresis decrease. Alloy electrode A shows better activation property and higher capacity (334.44 mAh/g). The addition of Cu improves the cyclic stability of the alloy electrodes when x?=?0?~?0.45. However, their self-discharge properties and high-rate dischargeability (HRD) decrease with the increase of x. Further, electrochemical kinetics and electrochemical impedance spectroscopy (EIS) analysis show that the reaction of alloy electrode is controlled by charge transfer step, and the adding of Cu benefits the electrode properties in alkaline solution.