离子液体电解质种类对活性炭电极超级电容器电化学性能的影响

本文将经水蒸气二次活化的椰壳活性炭（W-AC）作为电极材料,选择1-乙基-3甲基咪唑四氟硼酸盐（[EMIM]BF₄）作为电解质,结果表明W-AC电极的比电容量远高于未活化的椰壳活性炭（R-AC）.使用循环伏安、恒电流充放电、交流阻抗等方法研究了不同种类离子液体电解质对超级电容器电化学性能的影响.不同阴阳离子组成的离子液体作为电解质,直接影响超级电容器的电化学性能. 研究表明,由EMIM⁺和BMIM⁺阳离子与BF₄^-、TFSI^-阴离子构成的离子液体电解质较适用于W-AC电极. 其中在[EMIM]BF₄电解质中,单片电极的比电容量可高达153 F·g^-1;在1-丁基-3-甲基-咪唑四氟硼酸盐（[BMIM]BF₄）电解质中电位窗可达3.5V,能量密度可高达57 Wh·kg^-1.本研究对于构筑高性能超级电容器离子液体的选择提供参考,以满足不同应用领域需求.     

Au@SiO2膜/Ti电极吸附吡啶的表面增强拉曼光谱研究

基于壳层隔绝纳米粒子增强拉曼光谱技术,合成了Au@SiO₂纳米粒子,并对其进行了相关表征. 结果表明,包裹的二氧化硅层连续、致密,Au@SiO₂膜/Ti电极上可获得金属钛电极上吸附吡啶分子的高质量表面增强拉曼光谱（SERS）信号. 通过Pt、Ni电极的测试,证实该信号源于吸附在基底表面的吡啶分子. 此外,Au@SiO₂膜/Ti电极上吸附吡啶分子的现场SERS光谱研究表明,在-0.1 V ~ -0.6 V电位区间,吡啶分子平躺吸附,从-0.6 V起吸附的吡啶分子由平躺逐转变为垂直,而当电位为-1.2 V时,电极表面析氢,吡啶脱附.     

离子液体对木瓜蛋白酶催化特性的影响

研究了以1-丁基-3-甲基咪唑、四乙基铵及N-乙基吡啶为阳离子, 配以多种阴离子(H₂PO₄^-, ClO₄^-, HSO₄^-, CH₃COO^-, Cl^-, Br^-, NO₃^-, SCN^-, BF₄^-, PF₆^-)的离子液体对木瓜蛋白酶催化N-苯甲酰-L-精氨酸乙酯(BAEE)水解的活性及热稳定性的影响. 通过分析含离子液体体系中木瓜蛋白酶的水解活性和热力学失活参数, 发现该酶活性及稳定性与离子液体的Kosmotropicity性质无关. 因此, 离子的Hofmeister效应并不适合解释离子液体对木瓜蛋白酶催化特性的影响规律. 当以BF₄^-为阴离子, 改变阳离子结构时, 仅[BMIm][BF₄]可提高酶活性, 其它含官能团的咪唑类离子液体则降低酶活性, 但大部分离子液体明显提高木瓜蛋白酶的热稳定性. 在所研究的离子液体中, 基于PF₆^-或BF₄^-阴离子的离子液体可提高木瓜蛋白酶的活性及其热稳定性. 在含[BMIm][PF₆]介质中, 木瓜蛋白酶的水解活性最高; 在含[HOEtMIm][BF₄]介质中其热稳定性最好.     

离子液体中硫氰根在铂电极上吸附行为的SERS研究

利用表面增强拉曼光谱(SERS)研究了室温离子液体1-丁基-3-甲基咪唑氟硼酸盐([BMIM]BF4)中SCN-在Pt电极表面的吸附行为. 研究结果表明, 离子液体中SCN-在较宽的电位范围内吸附在Pt电极上, 且SCN-的吸附方式随着电位区间的变化而变化, 在不同的电位区间内检测到了不同的Stark位移: -0.9~0.4 V约为34 cm-1/V, 对应于S端吸附; -1.6~-1.2 V约为40 cm-1/V, 该区间以N端吸附为主, 中间电位区间为吸附方式的转变区, 且Pt电极在离子液体[BMIM]BF4中的零电荷电位约为-1.1 V(vs. Pt ).     

离子液体中铜纳米粒子膜的电沉积制备及表面增强拉曼光谱

采用恒电位方法研究了室温离子液体1-丁基-3-甲基咪唑氟硼酸盐([BMIM]BF₄)中氧化铟锡(ITO)电极表面Cu的沉积过程. 结果表明, Cu²⁺在ITO表面经中间产物Cu⁺还原为Cu. 采用XRD和SEM对不同电位下沉积层的组成和结构进行了考察. 结果表明, 表面组成和结构与沉积电位有关. 在较正电位下沉积所得为Cu/Cu₂O的混合纳米粒子; 在较负电位下为Cu纳米粒子. 随着沉积电位逐渐变负, 其形貌经历了花状、 棒状向球形纳米粒子转变的过程, 且所得沉积膜逐渐变得致密, 其中Cu纳米粒子膜表现出较强的表面增强拉曼散射(SERS)活性, 并且SERS信号均一.     

1-烷基-3-甲基咪唑系列室温离子液体表面张力的研究

合成了系列1-烷基-3-甲基咪唑四氟硼酸盐([C_2～7mim]BF₄)及六氟磷酸盐([C_4～7mim]PF₆)室温离子液体, 并通过核磁氢谱、红外光谱、质谱等手段对其进行了结构表征; 采用Wilhelmy白金板法, 在293～338 K范围内测定了离子液体的表面张力, 测试结果显示, 同类离子液体表面张力γ随温度的升高而线性下降, 同种离子液体的表面张力呈现出较宽的变化范围, 如293 K下, 表面张力值从[C₂mim]BF₄的50.4 mJ/m²到[C₇mim]BF₄的36.1 mJ/m². 最后对离子液体的表面性能进行了讨论.     

反气相色谱法表征离子液体1-己基-3-甲基咪唑四氟硼酸盐的热力学参数

采用反气相色谱法(IGC)表征了离子液体(IL)1-己基-3-甲基咪唑四氟硼酸盐([HMIM]BF₄)在343.15~373.15 K温度范围内的热力学参数.使用了一系列不同化学结构的探针分子测定[HMIM]BF₄与溶剂之间的相互作用力.根据探针分子的保留时间计算得到探针分子与[HMIM]BF₄之间的Flory-Huggins相互作用参数、摩尔吸附焓、无限稀释摩尔混合焓、摩尔蒸发焓、无限稀释活度系数以及[HMIM]BF₄的溶解度参数.结果表明,n-C₆、n-C₇、n-C₈、n-C₉、乙醚、四氢呋喃、苯、环己烷为[HMIM]BF₄的不良溶剂;甲苯、间二甲苯、甲醇、乙醇、二氯甲烷、四氯化碳、氯仿、丙酮、乙酸乙酯、乙酸甲酯为[HMIM]BF₄的良溶剂.运用外推法得到了[HMIM]BF₄在室温(298.15K)时的溶解度参数为23.70 (J·^-3)^0.5.实验结果证明反气相色谱法是一种简便准确的获得离子液体热力学参数的方法.获得的热力学参数体现了这种离子液体与探针分子之间的相互作用力.本研究为离子液体的进一步应用提供了参考.     

碱性体系中金电极表面硫氰根离子的宽带和频光谱研究

本文使用宽带和频光谱研究不同电位下碱性溶液中多晶金电极表面硫氰根离子（SCN^-）的吸附行为. 在-1.1 V ~ 0.2 V（vs. SCE）,C-N伸缩振动的Stark斜率的变化表明,随着电位正移,SCN^-在金电极表面从N端吸附变为S端吸附. 在较正电位下,C-N伸缩振动具有Fano线型. 这是因为金的费米能级随电位的正移而降低,和频过程中金的电子跃迁方式从带内跃迁（sp→sp）变为带间跃迁（d→sp）,造成金基底与表面吸附SCN^-和频信号的相对相位改变. 实验表明,通过研究和频光谱线型随电位的变化可以获取电极表面电子能级相对位置的信息.     

离子液体型表面活性剂研究

以1-甲基咪唑为原料, 制备了6个常规离子液体: 1-正丁基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[bmim][BF₄]及[bmim][PF₆])、1-正己基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[hmim][BF₄]及[hmim][PF₆])、1-正十六烷基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[C₁₆mim][BF₄]及[C₁₆mim][PF₆])和4个功能化离子液体: 1-(2-羟乙基)-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[2-hemim][BF₄]及[2-hemim][PF₆])、1-乙氧羰基甲基-3-甲基咪唑四氟硼酸盐及六氟磷酸盐(简称[eocmmim][BF₄]及[eocmmim][PF₆]). 研究了这两类离子液体的一些物理性能, 旨在挖掘离子液体在香料香精化妆品工业中的应用价值. 分别检测了它们与一般溶剂的互溶性, 并测定了它们的表面张力和发泡性能, 实验结果表明, 仅[C₁₆mim][BF₄]和[C₁₆mim][PF₆]具有发泡性能, 发泡力分别为68和120 mm.     

TiO2电极表面氰基吡啶吸附的电化学SERS光谱

采用基于核壳纳米粒子的壳层隔绝纳米粒子增强拉曼(SHINERS)以及Au纳米粒子增强技术, 对比研究了4-氰基吡啶(4-CNPy)在TiO2表面的吸附行为. 结果表明, 采用2种技术所获得的光谱存在明显的差别. 利用前者得到了4-CNPy在TiO2电极上随电极电位变化的吸附方式. 在电位为0时, 分子以吡啶环上的N垂直吸附; 随电位负移, 部分分子变为倾斜吸附, 且在电位为-1.0 V时倾斜角度变大. 在正电位区间, 分子始终以吡啶环上的N垂直吸附. 而采用Au纳米粒子滴加在TiO2电极上的方式, 则得到吸附在TiO2, Au及TiO2/Au复合结构上的总光谱信息.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).