Temperature dependence of oxygen reduction activity at Nafion-coated bulk Pt and Pt/carbon black catalysts

Oxygen reduction reaction (ORR) activity and H(2)O(2) formation at Nafion-coated film electrodes of bulk-Pt and Pt nanoparticles dispersed on carbon black (Pt/CB) were investigated in 0.1 M HClO(4) solution at 30 to 110 degrees C by using a channel flow double electrode method. We have found that the apparent rate constants k(app) (per real Pt active surface area) for the ORR at bulk-Pt (with and without Nafion-coating) and Nafion-coated Pt/CB (19.3 and 46.7 wt % Pt, d(Pt) = 2.6 to 2.7 nm) thin-film electrodes were in beautiful agreement with each other in the operation conditions of polymer electrolyte fuel cells (PEFCs), i.e., 30-110 degrees C and ca. 0.7 to 0.8 V vs RHE. The H(2)O(2) yield was 0.6-1.0% at 0.7-0.8 V on all Nafion-coated Pt/CB and bulk-Pt and irrespective of Pt-loading level and temperature. Nafion coating was pointed out to be a major factor for the H(2)O(2) formation on Pt catalysts modifying the surface property, because H(2)O(2) production was not detected at the bulk-Pt electrode without Nafion coating.     

Oxygen reduction activity of carbon-supported Pt-M (M = V, Ni, Cr, Co, and Fe) alloys prepared by nanocapsule method

Monodispersed Pt and Pt-M (M = V, Cr, Fe, Co, and Ni) alloy nanoparticles supported on carbon black (denoted as Pt/CB and Pt-M/CB) were prepared by the simultaneous reduction of platinum acetylacetonate and the second metal acetylacetonate within nanocapsules formed in diphenyl ether in the presence of carbon black. For the Pt/CBs, the average Pt diameters measured by scanning transmission electron microscopy (STEM) or X-ray diffraction (XRD) ranged from 2.0 to 2.5 nm, regardless of the catalyst-loading level from 10 to 55 wt % on CB. The alloy composition was found to be well-controlled to the projected value among the supported particles. The activities for the oxygen reduction reaction (ORR) at Nafion-coated catalysts in O2-saturated 0.1 M HClO4 solution were evaluated by using a channel flow electrode (CFE) cell at 30 degrees C. The area-specific ORR activities at Pt-M/CB were found to be 1.3 to 1.8 times higher than that at Pt/CB. The ORR activity increased in the order Pt/CB < Pt-Ni/CB < Pt-Fe/CB < Pt-Co/CB < Pt-V/CB < Pt-Cr/CB.     

以金属有机骨架为前驱体的高活性氧还原非贵金属催化剂制备

The development of a non‐precious metal electrocatalyst (NPME) with a performance superior to commercial Pt/C for the oxygen reduction reaction (ORR) is important for the commercialization of fuel cells. We report the synthesis of a NPME by heat‐treating Co‐based metal organic frameworks (ZIF‐67) with a small average size of 44 nm. The electrocatalyst pyrolyzed at 600 °C showed the best performance and the performance was enhanced when it was supported on BP 2000. The resulting electrocatalyst was composed of 10 nm Co nanoparticles coated by 3–12 layers of N doped graphite layers which as a whole was embedded in a carbon matrix. The ORR performance of the electrocatalyst was tested by rotating disk electrode tests in O2‐saturated 0.1 mol/L KOH under ambient conditions. The electrocatalyst (1.0 mg/cm2) showed an onset potential of 1.017 V (vs. RHE) and a half‐wave potential of 0.857 V (vs. RHE), which showed it was as good as the commer‐cial Pt/C (20μgPt/cm2). Furthermore, the electrocatalyst possessed much better stability and re‐sistance to methanol crossover than Pt/C.     

Pt（111）电极上O2与OHad的吸脱附及氧还原反应动力学

研究了Pt（111）电极在0．1mol／LHClO4溶液中O2吸附与OHad脱附及氧还原反应的动力学．研究发现OHad的可逆吸脱附速率很快;在氧还原的动力学或动力学与传质混合控制区,恒电位下氧还原的电流随反应时间缓慢衰减,在转速较大,扫速较慢的情形下正向扫描过程中氧还原的电流总是明显低于逆向扫描的电流;Pt／0．1mol／LHClO4从无O2切换到O2饱和时,其开路电位迅速从0．9V增加到1．0V．结果表明,Pt（111）电极上O2解离生成OHad速率很快,ORR过程中OHad会在表面缓慢积累,氧还原反应的动力学主要由反应 OHad＋H^＋＋e→←H2O的平衡热力学决定．     

Fe-N-modified multi-walled carbon nanotubes for oxygen reduction reaction in acid

We report a facile synthesis of Fe-N-C catalysts based on the surface functionalization of multi-walled carbon nanotubes (MWCNTs), which show high activity and stability for oxygen reduction reaction (ORR) in acid. Fe-N-MWCNT catalysts, whose ORR mass activities could vary by 3-4 times depending on the choice of Fe precursors, were found to have considerably higher ORR mass activity and higher stability than N-modified MWCNTs (N-MWCNTs). The Fe-N-MWCNT catalyst with a dominant Fe-N(x) moiety (with x ≈ 4) and a surface Fe/C ratio of ～0.004 exhibits the highest ORR mass activity in acid (～0.7 mA mg(-1)(Fe-N-MWCNT) at 0.8 V vs. RHE), where the lower mass activity of other Fe-N-MWCNT catalysts can be attributed to lower Fe/C ratios and Fe-N(x) moieties (with x smaller than 4) as revealed from X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS) spectroscopy. Moreover, the enhanced stability of Fe-N-MWCNTs in comparison to N-MWCNTs can be attributed to less H(2)O(2) production during ORR as determined from rotating ring disk electrode (RRDE) measurements, and higher activity for H(2)O(2) electro-reduction by rotating disk electrode (RDE) measurements. The large surface Fe/C ratio and Fe-N(x) moiety corresponding to high ORR activity and stability of Fe-N-MWCNTs demonstrate that surface functionalization can be very helpful to graft active catalytic sites onto carbon nanostructures, and to provide insights into the ORR mechanism of non-noble metal catalysts (NNMCs) for proton exchange membrane fuel cells (PEMFCs).     

Stable confinement of Fe/Fe_3C in Fe,N-codoped carbon nanotube towards robust zinc-air batteries

Catalytic oxygen reduction reaction(ORR) and oxygen evolution reaction(OER) have garnered great attention as the key character in metal-air batteries.Herein,we developed a superior nonprecious bifunctional oxygen electrocatalyst,fabricated through spatial confinement of Fe/Fe_3 C nanocrystals in pyridinic N and Fe-Nx rich carbon nanotubes(Fe/Fe_3 C-N-CNTs).During ORR,the resultant electrocatalyst exhibits positive onset pote ntial of 1.0 V(vs.RHE),large half-wave potentials of 0.88 V(vs.RHE),which is more positive than Pt/C(0.98 V and 0.83 V,respectively).Remarkably,Fe/Fe_3 C-N-CNTs exhibits outstanding durability and great methanol tolerance,exceeding Pt/C and most reported nonprecious metal-based oxygen reduction electrocatalysts.Moreover,Fe/Fe_3 C-N-CNTs show a markedly low potential at j=10 mA/cm~2,small Tafel slopes and extremely high stability for OER.Impressively,the Fe/Fe_3 C-N-CNTs-based Zn-air batteries demonstrate high power density of 183 mW/cm~2 and robust charge/discharge stability.It is revealed that the spatial confinement effect can impede the aggregation and corrosion of Fe/Fe_3 C nanocrystals.Meanwhile,Fe/Fe_3 C and Fe-Nx play synergistic effect on boosting the ORR/OER activity,which provides an important guideline for construction of inexpensive nonprecious metal-carbon hybrid nanomaterials.     

A first principles study of oxygen reduction reaction on a Pt(111) surface modified by a subsurface transition metal M (M = Ni, Co, or Fe)

We have performed first-principle density functional theory calculations to investigate how a subsurface transition metal M (M = Ni, Co, or Fe) affects the energetics and mechanisms of oxygen reduction reaction (ORR) on the outermost Pt mono-surface layer of Pt/M(111) surfaces. In this work, we found that the subsurface Ni, Co, and Fe could down-shift the d-band center of the Pt surface layer and thus weaken the binding of chemical species to the Pt/M(111) surface. Moreover, the subsurface Ni, Co, and Fe could modify the heat of reaction and activation energy of various elementary reactions of ORR on these Pt/M(111) surfaces. Our DFT results revealed that, due to the influence of the subsurface Ni, Co, and Fe, ORR would adopt a hydrogen peroxide dissociation mechanism with an activation energy of 0.15 eV on Pt/Ni(111), 0.17 eV on Pt/Co(111), and 0.16 eV on Pt/Fe(111) surface, respectively, for their rate-determining O2 protonation reaction. In contrast, ORR would follow a peroxyl dissociation mechanism on a pure Pt(111) surface with an activation energy of 0.79 eV for its rate-determining O protonation reaction. Thus, our theoretical study explained why the subsurface Ni, Co, and Fe could lead to multi-fold enhancement in catalytic activity for ORR on the Pt mono-surface layer of Pt/M(111) surfaces.     

B,N Co-Doped Three-Dimensional Carbon Aerogels with Excellent Electrochemical Performance for the Oxygen Reduction Reaction

Herein, an ordinary and mass-production approach is reported to synthesize boron (B) and nitrogen (N) co-doped three-dimensional (3D) carbon aerogels (CA) by using glucose and borax as the raw materials by a simple hydrothermal method and then carbonization in NH₃ atmosphere. The porous material (BN-CA-900) possesses a large specific surface area (1032 m² g⁻¹) and high contents of doped pyridinic N and graphitic N. The onset potential (0.91 V vs. reversible hydrogen electrode, RHE), half-wave potential (0.77 V vs. RHE), and current density (5.70 mA cm⁻² at 0.2 V vs. RHE) of BN-CA-900 for ORR are similar to those of commercial Pt/C, indicating that BN-CA-900 has a comparable catalytic activity with Pt/C in alkaline media. The number of electron transfer is 3.86–3.99 and the yield of hydrogen peroxide is less than 6.8 %. BN-CA-900 also presents decent catalytic performance in acidic medium. Moreover, the stability and methanol tolerance of BN-CA-900 are superior to commercial Pt/C in both alkaline and acidic media. The prepared BN-CA-900 is a promising candidate that may be applied in other areas, such as the adsorption of pollution, porous conductive electrodes, and lithium-ion batteries.     

Electro-oxidation of carbon monoxide on well-ordered Pt(111)/Sn surface alloys

The electro-oxidation of CO on model platinum-tin alloy catalysts has been studied by ex-situ electrochemical measurements following the preparation of the Pt(111)/Sn(2x2) and Pt(111)/Sn(radical3 x radical3)R30 degrees surfaces. A surface redox couple, which is associated with the adsorption/desorption of hydroxide on the Sn sites, is observed at 0.28 V(RHE)/0.15 V(RHE) in H(2)SO(4) electrolyte on both surfaces. Evidence that it is associated with the adsorption of OH comes from ex-situ photoemission measurements, which indicate that the Sn atoms are in a metallic state at potentials below 0.15 V(RHE) and an oxidized state at potentials above 0.28 V(RHE). Specific adsorption of sulfate anions is not associated with the surface process since there is no evidence from photoemission of sulfate adsorption, and the same surface couple is observed in the HClO(4) electrolyte. CO is adsorbed from solution at 300 K, with saturation coverages of 0.37 +/- 0.05 and 0.2 +/- 0.05 ML, respectively. The adsorbed CO is oxidatively stripped at the potential coincident with the adsorption of hydroxide on the tin sites, viz., 0.28 V(RHE). This strong promotional effect is unambiguously associated with the bifunctional mechanism. The Sn-induced activation of water, and promotion of CO electro-oxidation, is sustained as long as the alloy structure remains intact, in the potential range below 0.5 V(RHE). The results are discussed in the light of the requirements for CO-tolerant platinum-based electrodes in hydrogen fuel cell anode catalysts and catalysts for direct methanol electro-oxidation.     

Electrocatalytic reduction of oxygen at electrodes coated with a bimetallic cobalt(II)/platinum(II) porphyrin

Edge plane pyrolytic graphite (EPG) electrodes coated with 5-(4-pyridyl)-10,15,20-tris(3-methoxy-4-hydroxyphenyl)porphyrin and its Pt(II) and Co(II)/Pt(II) analogs undergo an electrochemical-chemical-electrochemical (ECE) reaction when anodically scanned in 1.0 M HClO4. The new redox couple formed from this anodic conditioning of the coated electrode is dependent on the pH of the solution. Roughened EPG electrodes coated with the Co(II)/Pt(II) bimetallic porphyrin show a catalytic shift of 500 mV for the reduction of O2 when compared to the reduction of O2 at a bare EPG electrode. An additional catalytic shift of ca. 100 mV is observed for O2 reduction at an EPG electrode coated with the Co(II)/Pt(II) porphyrin which has been oxidized in 1.0 M HClO4. In addition to the added electrocatalysis a significant percentage of O2 reduced at the oxidized Co(II)/Pt(II) EPG electrode is converted to H2O as determined by rotating disk electrode measurements.     

Carbon black supported PtCu nanoparticles derived from mix-phased Cu precursor for high-performanced oxygen reduction reaction in acid medium

Alloying high-cost Pt with transition metals has been considered as an effective route to synthesize the electrocatalysts with low Pt loading and excellent activity towards oxygen reduction reaction (ORR) under acid solution. The galvanic replacement method, as featured with efficiency and simplicity, is widely reported to produce Pt-based bimetallic alloys and thereby declare the significance of reductive transition metal precursor on the enhancement of ORR performance. Herein, mix-phased Cu−Cu₂O precursor was applied to prepare carbon black supported highly dispersed PtCu alloy nanoparticles (PtCu/C). The proper Cu−Cu₂O ratios can exactly facilitate the generation of small sized PtCu alloy nanoparticles with regulated bimetallic content. Meanwhile, the Cu₂O phase is revealed to benefit the electron transfer from Pt to Cu and thus improve the intrinsic activity of Pt active sites. And the metallic Cu can favor the promotion of electrochemical active surface area. Consequently, the as-prepared PtCu/C behaves impressive ORR activity with half-wave potential of 0.88 V (vs. RHE) and mass activity of 0.49 A cm⁻² mg_Pt⁻¹ at 0.8 V, which is 9.8 times of commercial Pt/C catalysts. Our work will offer helpful advices for the development and regulation of novel Pt-based alloy materials towards diverse electrocatalysis.     

CoPy/C催化剂应用碱性介质氧还原催化的电化学性能

利用碳黑（Vulcan XC-72R）中加入硫酸钴和吡啶（Py）作为催化剂前驱体,经溶剂分散热处理构建了一类新型的高效氧还原CoPy/C复合催化剂.并运用循环伏安法（CV）和旋转圆盘电极（RDE）技术研究了不同Co含量的CoPy/C催化剂在碱性介质中对氧还原的电催化活性.结果表明:Co的存在对氧的催化剂活性位的形成有重要影响,800℃下所制备的10%Co30%Py/C（质量分数）复合催化剂表现出最佳的氧还原催化活性.以其制备的气体扩散电极在3.0 mol·L^-1KOH电解质溶液（O₂气氛）中0.014 V（相对于标准氧电极（RHE））即可产生明显的氧还原电流.同40%Py/C相比,10%Co30%Py/C催化氧还原的起峰电位正移了71 mV,同时表现出明显的极限扩散电流.在-0.16 V时电流密度达到最大值,电流密度为1.0 mA·cm^-2,半波电位在-0.07 V.透射电镜分析表明所制备的碳黑载吡啶钴（10%Co30%Py/C）催化剂平均粒径为20 nm.     

氧还原和析氧反应的双功能电催化剂--氮磷共掺碳负载四氧化三钴

金属-空气电池具备诸多优势,譬如绿色环保、能量转化率高、启动快速、能量密度高、使用寿命和干态存储时间长等.与燃料电池相比,金属-空气电池结构简单,放电电压平稳,成本低,但依然存在一些制约发展的问题,如阴极催化剂.阴极催化剂在金属-空气电池中发挥催化氧还原反应(oxygen reduction reaction, ORR)和析氧反应(oxygen evolution reac-tion, OER)的关键作用.铂及其合金常用作 ORR的单功能催化剂,而钌和铱等是目前 OER催化效率最高的,但 ORR活性很低,因此需要开发出一种廉价而又具备双功能催化作用的催化剂.单异原子掺杂的碳基催化剂的研究集中在 ORR催化性能上,而多异原子共掺碳最近有研究表明具有双催化氧的性质,如氮磷共掺碳.在这些氮磷共掺的碳架中,氮磷共掺物起着 OER催化作用,掺氮物为 ORR催化的活性位点,而掺磷物起着强化作用.异原子掺杂负载的钴基催化剂(如掺氮还原氧化石墨烯载 Co3O4)是近年来双功能催化剂研究的另一个热点.钴基催化剂有着催化 ORR和 OER的多价价态,然而其本身导电性能差,这一缺陷可通过杂化石墨化碳来弥补,石墨化碳有着优良的导电性能.据我们所知,目前仍没有关于氮磷共掺碳负载的 Co3O4双催化氧的研究.我们合成了氮磷共掺碳(NPC)负载的 Co3O4(Co3O4/NPC),并首次探索了其氧还原和析氧性能. Co3O4/NPC合成分两步进行.首先通过三聚氰胺与植酸之间的酯化或缩聚覆盖在导电炭黑颗粒表面,在保护气氛下焙烧得到 NPC,然后经溶剂热反应以及空气中氧化合成 Co3O4/NPC.催化剂的性能综合考虑了催化活性和稳定性两方面.采用线性扫描伏安法评估了 OER和 ORR的催化活性.对于 OER, Co3O4/NPC的起始电势是0.54 V (以饱和甘汞电极为参比电极),在0.80 V时电流密度达到21.95 mA/cm2,均优于 Co3O4/C和 NPC. Co3O4/NPC的高效 OER催化可归因于氮磷共掺物与 Co3O4之间的协同作用.对于 ORR, Co3O4/NPC的催化效率与商用 Pt/C相近,它们的扩散极限电流密度分别为–4.49和–4.76 mA/cm2(E =–0.80 V).在 ORR过程中, Co3O4起到主要的催化作用.采用计时电流(电流-时间)法评估了催化剂的稳定性.经6 h测定,对于 OER, Co3O4/NPC剩46%电流;而对于 ORR,剩95%电流.整体而言, Co3O4/NPC在 OER和 ORR中都表现出高的催化效率以及良好的稳定性.     

Pd/Pt二元合金电极的制备及氧还原性能

本文利用欠电位沉积亚单层的Cu及Pt置换取代Cu的方法, 制备了具有不同表面元素组成的Pd/Pt二元合金电极(用Pd/Ptx表示, x指欠电位沉积Cu-Pt置换取代Cu过程的次数),并对其表面元素组成、氧还原性能进行了表征. 在控制欠电位沉积Cu的下限电位恒定(0.34 V)的前提下, 表面Pt/Pd的元素组成比通过重复欠电位沉积Cu及Pt置换取代Cu的次数(1~5次)来可控地调变. 光电子能谱(XPS) 以及红外光谱实验表明,Pd/Ptx电极表层区的Pt：Pd元素组成比随着Pt沉积次数增加而增加, 对Pd/Pt4电极, 在电极表层区约2~3 nm内的Pt/Pd的原子比大约是1:4,而最表层裸露Pd原子的比例仍在20%以上。循环伏安结果显示, 随着Pt沉积次数的增加(1-5次), Pd/Ptx电极表面越不易被氧化。氧还原测试结果显示随着Pt沉积次数的增加(1~4次), Pd/Ptx二元金属电极的氧还原活性依次增加, 经过第3次沉积后其氧还原活性已优于纯Pt,而经4次以上沉积,其氧还原活性基本不变。在其它反应条件相同条件的前提下, Pd/Pt4电极上氧还原的半波电位与纯Pt相比右移约25 mV。结合本文与文献的实验结果,我们初步认为Pd/Ptx二元金属体系氧还原性能改善主要源自表层Pd原子导致其邻近的Pt原子上含氧物种吸附能的降低.     

氢钼青铜对铂催化氧还原反应的促进作用

采用循环伏安法在玻碳电极上和硫酸溶液中电沉积制备出铂催化剂(Pt)及铂-氢钼青铜复合催化剂(Pt-HxMoO3), 用旋转圆盘电极研究并比较了它们对硫酸溶液中氧还原反应的催化活性. 研究结果表明, HxMoO3能明显地提高Pt对氧还原反应的电催化活性. 通过对静态电极上氧还原的峰电流与扫描速度的关系以及旋转圆盘电极上氧还原电流与旋转速度的关系的分析发现, HxMoO3提高了铂电极氧还原反应电荷传递步骤的传递系数, 因此加快了氧还原的动力学过程.     

Self-assembly and heterogeneous electron transfer properties of metallo-octacarboxyphthalocyanine complexes on gold electrode

Electrochemical properties of redox-active self-assembled molecular films of novel metallo-octacarboxyphthalocyanine (MOCPc, M = Fe, Co and Mn) complexes integrated with cysteamine (Cys) monolayer on gold electrodes via amide bonds were investigated. X-Ray photoelectron spectroscopy confirmed the appearance of the various elements in their expected chemical environment upon immobilization of these species. The heterogeneous electron transfer properties of the Au-Cys-MOCPc molecular films using an outer-sphere ([Fe(CN)(6)](4-)/[Fe(CN)(6)](3-)) redox probe were studied using cyclic voltammetry and electrochemical impedance spectroscopy. The electron transfer rate constant (k(app)) depends markedly on the central metal of the metallophthalocyanine cores (k(app): Co > Mn > Fe). A strong pH dependence of the electron transport of the Au-Cys-MOCPc molecular films was found. The surface pK(a) values of the MOCPc complexes were essentially the same (ca. 7.5). The differences in the electron transports and ionization constants are discussed. The electrodes are sensitive to the electrooxidation of epinephrine in physiological pH conditions, peak potential (E(p)/V vs. Ag|AgCl, saturated KCl) decreasing as FeOCPc (0.20 V) < MnOCPc (0.26 V) < CoOCPc (0.34 V).     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

电沉积制备的PtNi纳米粒子用于氧还原反应:成核和生长机理

质子交换膜燃料电池(PEMFCs)电堆中阴极Pt基催化剂的高用量造成其成本居高不下,成为阻碍燃料电池汽车商业化推进的重要原因,因此开发低Pt、高活性的Pt基催化剂势在必行.Pt合金催化剂能够有效地降低Pt用量,并通过对合金颗粒的元素比例、晶面、粒径等实行精确调控,显著提升氧还原(ORR)催化活性.然而,目前常用的制备方法由于原料与制备成本高昂、过程复杂大都难以适应规模化生产需求.电化学方法通过控制施加的电流或电位控制晶体生长.在水体系中该方法已得到验证,但由于Pt化合物的热力学标准电极电位与过渡金属元素之间相差较大,且对于过渡金属来说,电负性大多小于铂,因此还原电位通常负于析氢电位,使得二者难以实现共沉积.有机体系中电位窗口比水体系大得多,Pt与电位较负的过渡金属可实现共沉积,采用小分子有机溶剂也可避免溶剂清洗问题,具有应用潜力.本文提出了一种简单的一步电沉积方法,选择易溶于水的N,N-二甲基甲酰胺(DMF)作为溶剂,将碳载体滴涂到玻碳电极上作为工作电极,通过电化学方法直接将Pt-Ni合金沉积到碳载体上,并利用物化表征与密度泛函理论(DFT)理论计算来探究共沉积机理.透射电镜表征结果表明,在不同的沉积电位下均可得到分散均匀、粒径适当的催化剂;且随着电位值降低,催化剂颗粒分散得更均匀,颗粒粒径不断减小.元素分布和晶面结果表明,铂镍元素均匀分布于颗粒中.所有样品均表现出优异的ORR性能,最高的面积比活性达到商业催化剂的6.85倍.将材料表征、电化学表征与DFT计算结合,建立起了铂镍合金生长过程的模型,并发现了有机体系中独特的成核-生长机理.将体系中的DMF换成超纯水,用同样的方法进行沉积,得到的催化剂颗粒团聚严重,说明DMF的使用能够避免颗粒团聚.在单独铂的体系中沉积发现,负载量极小,表明体系中镍前驱体的添加对于催化剂的沉积过程起到重要作用.电化学表征结果表明,在所选用的DMF有机体系中,镍的还原电位与铂的十分接近,但还原动力学更慢,趋向于先形成吸附原子后快速还原.由此可以推测,在二者合金的形成过程中,镍在碳载体表面的缓慢还原而形成的吸附原子能够成为铂还原的活性位点,从而降低了铂还原成核所需的能量,使得载体上的成核位点大大增加,这与DFT模拟结果一致.DFT建立了碳上镍的位点和铂的位点,分别在上面进行铂的还原,发现镍位点上比铂位点上更容易实现铂沉积.本文提出了铂镍共沉积的机理:在过电位(即还原能量)下,铂的还原动力学较镍稍快,于是铂先还原形成晶核,但难以达到生长的临界半径,于是单独铂体系中的沉积负载量很少.载体上还原的镍为铂还原提供了大量的活性位点,促进了铂还原,并与镍共沉积.Pt-Ni表面则进一步促进了铂的沉积和颗粒的生长.综上,本文提出了一种用于制备铂合金催化剂的有机电沉积体系,实现了单分散的碳载铂镍合金催化剂的一步制备.随后,本文将材料表征、电化学表征与DFT计算相结合,建立起了有机体系中铂镍合金成核-生长过程的机理模型.     

Amino-metalloporphyrin polymers derived Fe single atom catalysts for highly efficient oxygen reduction reaction

Recently, nitrogen-doped porous carbon supported single atom catalysts(SACs) have become one of the most promising alternatives to precious metal catalysts in oxygen reduction reaction(ORR) due to their outstanding performance, especially those derived from porphyrin-based materials. However, most of them involve other metal residuals, which would cause the tedious pre-and/or post-treatment, even mislead the mechanistic investigations and active-site identification. Herein, we report a precursor-dilution strategy to synthesize Fe SACs through the Schiff-based reaction via co-polycondensation of amino-metalloporphyrin, followed by pyrolysis at high temperature. Systematic characterization results provide the compelling evidence of the dominant presence of atomically dispersed Fe-Nxspecies. Our catalyst shows superior ORR performance with positive half-wave potential(E_(1/2)=0.85 V vs. RHE) in alkaline condition and moderate activity(E_(1/2)=0.68 V vs. RHE) under the acidic condition, excellent methanol tolerance and good long-term stability. All the results indicate Fe SACs would be a promising candidate for replacing the precious Pt in metal-air batteries and fuel cells.     

电沉积制备的PtNi纳米粒子用于氧还原反应:成核和生长机理

质子交换膜燃料电池(PEMFCs)电堆中阴极Pt基催化剂的高用量造成其成本居高不下,成为阻碍燃料电池汽车商业化推进的重要原因,因此开发低Pt、高活性的Pt基催化剂势在必行.Pt合金催化剂能够有效地降低Pt用量,并通过对合金颗粒的元素比例、晶面、粒径等实行精确调控,显著提升氧还原(ORR)催化活性.然而,目前常用的制备方法由于原料与制备成本高昂、过程复杂大都难以适应规模化生产需求.电化学方法通过控制施加的电流或电位控制晶体生长.在水体系中该方法已得到验证,但由于Pt化合物的热力学标准电极电位与过渡金属元素之间相差较大,且对于过渡金属来说,电负性大多小于铂,因此还原电位通常负于析氢电位,使得二者难以实现共沉积.有机体系中电位窗口比水体系大得多,Pt与电位较负的过渡金属可实现共沉积,采用小分子有机溶剂也可避免溶剂清洗问题,具有应用潜力.本文提出了一种简单的一步电沉积方法,选择易溶于水的N,N-二甲基甲酰胺(DMF)作为溶剂,将碳载体滴涂到玻碳电极上作为工作电极,通过电化学方法直接将Pt-Ni合金沉积到碳载体上,并利用物化表征与密度泛函理论(DFT)理论计算来探究共沉积机理.透射电镜表征结果表明,在不同的沉积电位下均可得到分散均匀、粒径适当的催化剂;且随着电位值降低,催化剂颗粒分散得更均匀,颗粒粒径不断减小.元素分布和晶面结果表明,铂镍元素均匀分布于颗粒中.所有样品均表现出优异的ORR性能,最高的面积比活性达到商业催化剂的6.85倍.将材料表征、电化学表征与DFT计算结合,建立起了铂镍合金生长过程的模型,并发现了有机体系中独特的成核-生长机理.将体系中的DMF换成超纯水,用同样的方法进行沉积,得到的催化剂颗粒团聚严重,说明DMF的使用能够避免颗粒团聚.在单独铂的体系中沉积发现,负载量极小,表明体系中镍前驱体的添加对于催化剂的沉积过程起到重要作用.电化学表征结果表明,在所选用的DMF有机体系中,镍的还原电位与铂的十分接近,但还原动力学更慢,趋向于先形成吸附原子后快速还原.由此可以推测,在二者合金的形成过程中,镍在碳载体表面的缓慢还原而形成的吸附原子能够成为铂还原的活性位点,从而降低了铂还原成核所需的能量,使得载体上的成核位点大大增加,这与DFT模拟结果一致.DFT建立了碳上镍的位点和铂的位点,分别在上面进行铂的还原,发现镍位点上比铂位点上更容易实现铂沉积.本文提出了铂镍共沉积的机理:在过电位(即还原能量)下,铂的还原动力学较镍稍快,于是铂先还原形成晶核,但难以达到生长的临界半径,于是单独铂体系中的沉积负载量很少.载体上还原的镍为铂还原提供了大量的活性位点,促进了铂还原,并与镍共沉积.Pt-Ni表面则进一步促进了铂的沉积和颗粒的生长.综上,本文提出了一种用于制备铂合金催化剂的有机电沉积体系,实现了单分散的碳载铂镍合金催化剂的一步制备.随后,本文将材料表征、电化学表征与DFT计算相结合,建立起了有机体系中铂镍合金成核-生长过程的机理模型.