丙烯酸甲酯与醋酸乙烯酯的种子乳液聚合

以过硫酸铵（ＡＰＳ） 为引发剂,合成了粒径分布较均匀的聚醋酸乙烯酯种子乳液（ＰＶＡｃ） ,然后以丙烯酸甲酯（ ＭＡ） 为第二单体和以油溶性偶氮二异丁腈（ＡＩＢＡ） 为引发剂,分别进行不溶胀与溶胀条件下的无皂种子乳液聚合,并用透射电子显微镜（ＴＥＭ） 表征了胶粒形态．表明在不溶胀条件下,胶粒形态随ＰＶＡｃ／ ＭＡ 重量比的不同而变化,当ＰＶＡｃ／ ＭＡ 为１／２ 时,形成以ＰＭＡ 为核,ＰＶＡｃ 为壳的胶粒．在溶胀条件下则得到类似互穿网络型乳胶粒．     

间规聚苯乙烯的非等温结晶及其动力学

以Ｓｔ－ＭＭＡ－ＡＡ三元无皂共聚胶粒作载体,用物理吸附和共价偶联两方法固载日本血吸虫虫卵可溶性抗原（Ｓｊ－ＳＥＡ）。探讨了胶粒性质对Ｓｊ－ＳＥＡ固载量及活性的影响,研究结果表明,胶粒表面疏水性强或胶乳表面张力大,则物理吸附量大,但致敏胶乳的效价并不一定高;胶粒表面羧基密度大,共价偶联量多,但共价偶联量太大时,致敏乳效价低;在共价偶联量较小时,致敏胶乳的效价随固载的Ｓｉ－ＳＥＡ密度增大而提高。     

微波辐照制备多孔乳胶粒

在微波辐照的条件下，通过间歇无皂种子乳液聚合，制得聚[苯乙烯－甲基丙烯酸甲酯－丙烯酸]复合乳液。将所得复合胶乳进行碱／酸分段处理，得到具有多孔结构的乳胶粒。用透射电镜对胶粒形态进行了表征，研究了不饱和酸用量、碱处理初始pH值及碱处理时间对胶粒成孔的影响。     

微波种子乳液聚合制备多孔乳胶粒

微波辐照下，通过间歇无皂种子乳液聚合制得聚(苯乙烯-甲基丙烯酸甲酯-丙烯酸)复合乳液，将所得复合乳液进行碱／酸分段处理，得到具有多孔结构的乳胶粒。用透射电镜对胶粒形态进行了表征。研究了酸处理初始pH值及酸处理时间对胶粒成孔的影响。     

离子型共聚单体用于高固含量无皂乳液聚合的研究：甲基丙烯酸异丁 …

该文采用自行合成的一种带亲水性磺酸离子基团及羟基的可共聚单体３－烯丙氧基－２－羟基丙磺酸钠（ＡＨＰＳ）用于甲基丙烯酸异丁酯／甲基丙烯酸甲酯／丙烯酸丁酯（ＩＢＭＡ／ＭＭＡ／ＢＡ）无皂乳液聚合体系。对乳胶粒粒径大小、乳液流体力学行为、共聚物的动态力学性质、拉伸行为及耐水性进行了研究,并对乳胶粒的成核机理进行了探讨。实验结果表明,带亲水性离子基团可共聚单体ＡＨＰＳ的加入可获得０．６μｍ左右的乳胶粒,乳液     

乙烯基聚硅氧烷共聚反应竞聚率的测定及其对复合粒子形态的影响

用Ｆｉｍｅｍａｎ－Ｒｏｓｓ法处理数据，测定了乙烯基聚硅氧烷（ＳＶ）与苯乙烯（ＳＴ）、甲基丙烯酸甲酯（ＭＭＡ）和甲基丙烯酸正丁酯（ｎ－ＢＭＡ）的共聚反应的竞聚率，结果为ｒＳＴ＝１．４５和ｒＳＶ＝１．０８，ｒＭＭＡ＝０．７８和ｒＳＶ＝２．０１，ｒｎ－ＢＭＡ＝０．４６和ｒＳＶ＝３．４９．以含ＳＶ的乳液作为种子进行烯类单体的乳液聚合，单体和ＳＶ共聚反应对复合粒子的形态有很大影响。     

苯乙烯—甲基丙烯酸超浓乳液的制备及聚合

超浓乳液聚合有着良好的应用前景［１，２］．但文献报道的超浓乳液研究多集中于苯乙烯体系，而对于在此基础上引入功能基单体制备超浓乳液，研究得较少［３］．本文研究了影响苯乙烯（Ｓｔ）与甲基丙烯酸（ＭＡＡ）制备（Ｓｔ－ＭＡＡ）超浓乳液稳定性的因素．探讨了其聚...     

含氢聚甲基硅氧烷/丙烯酸丁酯/羟甲基丙烯酰胺复合乳液的研究——原料配比对乳液及胶膜性能的影响

采用含氢聚甲基硅氧烷（ＰＨＭＳ）与丙烯酸酯类单体进行接枝共聚，制得兼具二者优异性能的新型ＰＨＭＳ／丙烯酸丁酯（ＢＡ）／羟甲基丙烯酰胺（ＮＭＡ）复合聚合物乳液．讨论了ＰＨＭＳ、ＮＭＡ和引发剂用量对该复合乳液的聚合反应转化率、稳定性及粘度的影响．采用透射电子显微镜和粒度测试仪对不同反应条件下制备的乳液的粒度进行了测定．同时对聚合反应的机理、产物的结构及胶膜性能作了考察．结果表明：通过乳液聚合，得到了ＰＨＭＳ／ＢＡ／ＮＭＡ共聚物，控制ＰＨＭＳ、ＮＭＡ、引发剂等用量可制得粒度和粘度适中，具有较高转化率的稳定ＰＨＭＳ／ＢＡ／ＮＭＡ复合聚合物乳液，该乳液所制得的胶膜具有优良的性能     

乙基基聚硅氧烷共聚反应竞聚率的测定及其对复合粒子形态的影响

用Ｆｉｍｅｍａｎ－Ｒｏｓｓ法处理数据，测定了乙烯基聚硅氧烷与苯乙烯，甲基丙烯酸甲酯和甲基丙烯酸正丁酯的共聚反应的竞聚率，结果为ｓｔ＝１，４５和ｒｓｖ＝１．０８，ｒＭＭＡ＝０．７８和ｒｓｖ＝２．１，ｒａ－ＢＭＡ＝０．４６和ｒｓｖ＝３．４９。以含ＳＶ的乳液作为种子进行烯类单体的乳液聚合，单体和ＳＶ共聚反应对复合粒的形态有很大影响。     

种子乳液聚合物胶粒形态及胶膜结构研究

以醋酸乙烯酯和丙烯酸丁酯为单体，用乳液聚合方法，以极性小的ＰＢＡ为种子进行了ＶＡ种子聚合，用透射电镜染色及皂液滴定方法对胶粒形态进行了表征，结果，上述聚合反应能形成ＰＢＡ／ＰＶＡ核壳结构的胶粒，而以ＰＶＡ为种子对ＰＢＡ进行聚合，则不能形成ＰＶＡ／ＰＢＡ核壳结构的胶粒，其胶粒亦具有类似ＰＢＡ／ＰＶＡ核壳结构或半包囊结构，将胶乳制成胶膜，其耐水性能测试表明成膜后胶粒基本保持了其分散阶段的形态。     

交联剂对无皂P(MMA-EA-MAA)种子聚合乳胶粒成孔的影响

采用完全无皂种子乳液聚合技术合成了粒径窄分布的P(MMA-EA-MAA)乳胶粒,通过对上述胶乳进行碱处理,制备出了具有空腔结构和多孔结构的聚合物乳胶粒,研究了交联剂的种类和用量对聚合过程、胶粒特性及胶粒结构形态的影响.结果表明,体系中加入交联剂后,单体转化率都有不同程度的提高;随交联剂用量的增加,乳胶粒粒径略有减小,交联剂用量较高时,乳胶粒粒径分布加宽;二乙烯基苯(DVB)的交联效率稍高于双甲基丙烯酸乙二醇酯(EGDMA);不加入交联剂及EGDMA用量低于0.5%时,处理后乳胶粒呈空腔结构,加入DVB及EGDMA用量高于1.0%时,处理后乳胶粒呈多孔结构,并且乳胶粒体积增量随交联剂用量的增加而减小.     

Preparation and Characterization of Polymer Core Shell Latex Particles

Stable core‐shell latex was synthesized by semicontinuous seeded emulsion polymerization with core monomers consisting of styrene (St), butyl acrylate (BA), and shell monomers consisting of methyl methacrylate (MMA), eutyl acrylate (EA), and methacrylic acid (MAA). The effects of compound emulsifier amount, mass ratio of anionic/nonionic emulsifier, and initiator amount on latex performance were investigated. By particle size analysis and transmission electron microscopy (TEM) observation, results suggest that final latex particles have clearly core shell structures.     

Morphological evolution of multistage polymer particles in the alkali post-treatment

Multistage carboxyl-containing polymer latex particles were synthesized by multistep emulsion copolymerization using methyl methacrylate (MMA), butyl acrylate (BA), methacrylic acid (MAA), ethylene glycol dimethacrylate (EGDMA) and styrene (St) as raw materials, and the latex particles with diverse morphologies including multihollow, hollow and “bowl-like” were obtained by post-treating the multistage latex particles under alkali condition. The morphological evolution of the particles in the alkali post-treatment process was characterized with electron microscopy, and effects of alkali treatment conditions including treatment temperature, time as well as initial pH on particle morphology were investigated. Results indicated that the alkali treatment temperature and initial pH were the key parameters to control the morphology of the treated particles. When the alkali treatment temperature was below 60 °C or the initial pH was lower than 8.5, the particle morphology was almost unchanged no matter how long the treatment time was prolonged. The multihollow and hollow particles could be formed as alkali treatment temperature exceeded 60 °C in the range of initial pH from 8.8 to 9.5. While the latex particles with “bowl-like” morphology were observed when the multistage latex was alkali treated at 90 °C for 3 h with initial pH 9.8. Furthermore, extending alkali treatment time was beneficial to get the swelling equilibrium of the latex particles.     

Synthesis and characteristics of poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive semi‐hollow latex particles and their application to drug carriers

In this work, the poly(methyl methacrylate‐co‐methacrylic acid)/poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite semi‐hollow latex particles was synthesized by three processes. The first process was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly (MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second process was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and crosslinking agent, N,N′‐methylenebisacrylamide, in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles with solid structure. In the third process, part of the linear poly(MMA‐MAA) core of core–shell latex particles was dissolved by ammonia to form the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles. The morphologies of the semi‐hollow latex particles show that there is a hollow zone between the linear poly(MMA‐MAA) core and the crosslinked poly(MAA‐NIPAAm) shell. The crosslinking agent and shell composition significantly influenced the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) semi‐hollow latex particles. Besides, the poly(MMA‐MAA)/poly(MAA‐NIPAAm) thermosensitive semi‐hollow latex particles were used as carriers to load with the model drug, caffeine. The processes of caffeine loaded into the semi‐hollow latex particles appeared four situations, which was different from that of solid latex particles. In addition, the phenomenon of caffeine released from the semi‐hollow latex particles was obviously different from that of solid latex particles. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3441–3451     

DESIGN AND CONTROL OF SOAP-FREE HYDROPHILIC-HYDROPHOBIC CORE-SHELL LATEX PARTICLES WITH HIGH CARBOXYL CONTENT IN THE CORE OF THE PARTICLES

Soap-free hydrophilic-hydrophobic core-shell latex particles with high carboxyl content in the core of the particles were synthesized via the seeded emulsion polymerization using methyl methacrylate(MMA),butyl acrylate(BA), methacrylic acid(MAA),styrene(St)and ethylene glycol dimethacrylate(EGDMA)as monomers,and the influences of MMA content used in the core preparation on polymerization,particle size and morphology were investigated by transmission electron microscopy,dynamic light scattering and conductometric titration.The results showed that the seeded emulsion polymerization could be carried out smoothly using "starved monomer feeding process" when MAA content in the core preparation was equal to or less than 24 wt%,and the encapsulating efficiency of the hydrophilic P(MMA-BA-MAAEGDMA) core with the hydrophobic PSt shell decreased with the increase in MAA content.When an interlayer of P(MMAMAA -St)with moderate polarity was inserted between the P(MMA-BA-MAA-EGDMA)core and the PSt shell,well designed soap-free hydrophilic-hydrophobic core-shell latex particles with 24 wt%MAA content in the core preparation were obtained.     

Synthesis and characteristics of poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles and their application as drug carriers

In this work, the poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles was synthesized by a three‐step reaction. The first step was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second step was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and N,N′‐methylenebisacrylamide in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles. In the third step, the core–shell latex particles were heated in the presence of ammonia solution to form the crosslinking poly(MAA‐NIPAAm) thermosensitive hollow latex particles. The morphologies of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were observed. The influences of crosslinking agent and shell composition on the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were, respectively, studied. Besides, the poly(MAA‐NIPAAm) thermosensitive hollow latex particles were used as carriers to load with the model drug, caffeine. The effect of various variables on the amount of caffeine loading and the efficiency of caffeine release was investigated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5203–5214     

Influence of Emulsifiers on Acrylate Latex Blends

The poly(methyl methacrylate/butyl acrylate/acrylic acid) [P(MMA/BA/AA)] and poly (styrene/butyl acrylate/acrylic acid) [P(St/BA/AA)] latexes were synthesized using the emulsifier octylphenol polyoxyethylene(10) ether (OP-10) and ammonium sulfate allyloxy nonylphenoxy poly(ethyleneoxy)(10) ether(DNS-86). The optimum amount of OP-10 and DNS-86 was 1.5% and 2.5% respectively. The P(MMA/BA/AA) and P(St/BA/AA) latex containing 1.5% OP-10 or 2.5% DNS-86 were blended pairwise. The performances of latex blends and parent latexes as a function of emulsifiers content in parent latexes were determined. The results indicated that the stability of latex blends is favorable, and particle size distribution was more uniform and thermal stability was improved after blending.     

Polar Gradient Latex Particles with Hydrophilic Core and Hydrophobic Shell Prepared via Multistep Emulsion Polymerization

Monodisperse polar gradient particles were synthesized via a three‐step emulsion polymerization using poly(butyl acrylate‐methyl methacrylate‐methacrylic acid‐ethylene glycol dimethacrylate) (P(BA‐MMA‐MAA‐EGDMA)) as core, poly(methyl methacrylate‐methacrylic acid‐styrene) (P(St‐MMA‐MAA)) as interlayer and polystyrene (PSt) as shell. The particle growth and encapsulation in each emulsion polymerization step were followed by transmission electron microscopy (TEM), dynamic light scattering (DLS) and conductometric titration. Results indicated that the feeding mode and the interlayer were essential to prepare the polar gradient latex particles with hydrophilic core and hydrophobic shell. The morphologies of the two‐layer core/interlayer and three‐layer core/interlayer/shell particles were observed in TEM micrographs, and the sequential encapsulations of the carboxyl‐containing core and the core/interlayer particles were confirmed by an increase in the particle size as well as an increase in the buried carboxyl percentage.     

Preparation of multihollow P(St-MAA) particles by sequence soap-free/soap emulsion polymerization and followed by stepwise alkali/acid posttreatment

The effects of ionic emulsifier, sodium dodecylbenzene sulfate (SDBS), on the formation of the multihollow structures in sub-micron sized polymer particles produced by alkali/acid posttreatment were investigated. The original latex particles with narrow size distribution were synthesized by a new sequence emulsifier-free/emulsifier emulsion copolymerization of styrene (St) and methacrylic acid (MAA). Results indicated that the pore size decreased and the pore number increased with the increase of SDBS amount, and the morphology of the posttreated latex particles was also significantly influenced by the introducing time of SDBS in the preparation of the original latex particles, and a suitable introducing time was 3 h of polymerization.     

The characterization of latex particles prepared by pulsed electron beam induced emulsion polymerization

The emulsion polymerization of styrene (St) and methyl methacrylate (MMA) induced by 10 MeV pulsed electron beams (PEB) was investigated. The monomer conversion of MMA and St was found to be very low so that the final prepared poly(methyl methacrylate) (P(MMA)) and polystyrene (PS) latex particles exhibit porous structures, as verified by TEM and SEM observations. The results of dynamic light scattering (DLS) and gel permeation chromatography (GPC) showed that both the particle size and the molecular weight of PS and PMMA latexes decrease with the increase of the absorbed dose. However, the molecular weights and the particle sizes of the PS and PMMA latexes change differently with the irradiation time. This work indicated that emulsion polymerization induced by high energy electron beam has an advantage over that induced by γ-ray or chemical initiators in the preparation of latex with a low molecular weight and porous structure.