氮-硫共掺杂二氧化钛光催化剂的制备及其可见光催化活性

采用研磨煅烧法,以硫脲(TU)作为氮源和硫源,H2TiO3(HT)为TiO2的前驱体,制备了不同TU/HT比例的N,S共掺杂TiO2光催化剂(NS/TiO2);利用X射线衍射仪、透射电镜、X射线光电子能谱仪、拉曼光谱仪、紫外-可见吸收光谱仪等分析了NS/TiO2的晶体结构、显微形貌、典型元素的化学状态以及光谱性质;利用BET法测定了NS/TiO2的比表面积,同时测定了其在可见光照下催化降解罗丹明B的活性.结果表明,当TU/HT质量比为0.5时,NS/TiO2的光催化活性最佳,光照70min时的罗丹明B降解率为44.4%.氮元素以NH3形式吸附在TiO2表面,硫元素以S6+形式存在,部分S6+取代Ti 4+的位置.与此同时N,S共掺杂使得TiO2的禁带宽度减小,可见光催化活性提高.     

N掺杂富含(001)晶面TiO_2纳米片的制备及N掺杂浓度对可见光催化活性的影响(英文)

采用水热法制备了富含(001)晶面的锐钛矿型TiO2纳米片,并通过改变热处理过程中NH3流速制备不同N掺杂浓度的TiO2纳米片.运用X射线衍射、场发射扫描电镜、高分辨率透射电子显微镜、紫外-可见漫反射光谱、X射线光电子能谱和荧光光谱对光催化剂进行了结构和性能表征,并以罗丹明B为目标降解物,考察了N掺杂浓度对TiO2纳米片可见光催化活性的影响.结果表明,NH3流速为40ml/min时制备的N掺杂TiO2纳米片具有最低的光生电子-空穴复合速率,最高的OH产生能力并表现出最高的光催化活性.同时,讨论了N掺杂浓度对TiO纳米片可见光催化活性影响的机理.     

新型N-TiO2的固相法制备及其光催化性能

以纳米管钛酸为前驱体,以NH4HCO3为N源,先机械研磨使二者混合均匀,再在Ar保护下,于不同温度焙烧4h制得N掺杂TiO2 (N-TiO2),并采用X射线粉末衍射、X射线光电子能谱、紫外-可见吸收光谱、透射电镜及N2吸附-脱附对样品进行了表征.结果显示,N以间隙掺杂方式进入TiO2晶格内.在热处理过程中,生成中间体(...     

N、F共掺杂TiO2可见光响应光催化剂的酸催化水解法制备及表征

采用酸催化水解法由TiCl4、NH4F混合液合成N、F共掺杂可见光响应TiO2光催化剂(TONF). 以苯酚为模型物, 考察了催化剂在可见光区、紫外光区的催化活性. 采用X射线光电子能谱(XPS)、紫外-可见漫反射光谱(DRS)、X射线衍射(XRD)、扫描电子显微镜(SEM)及低温氮物理吸附对光催化剂的晶相结构、光谱特征和表面结构等进行表征. 结果表明, 适量的N、F共掺杂TONF催化剂表现出较高的可见光催化活性. N、F共掺杂可显著提高TiO2分散性能, 促进锐钛矿相的形成, 抑制其向金红石相转变, 提高相转变温度. N掺杂可提高TiO2在可见光区的吸收; F掺杂可使TiO2能隙变窄.     

钛基表面N掺杂TiO_2纳米管电极的光电催化性能

利用电化学阳极氧化法和浸渍法制备出N掺杂TiO2纳米管电极。采用扫描电子显微镜(SEM)、紫外-可见/漫反射吸收光谱(UV-Vis/DRS)技术对其进行表征。考察了该电极对甲基橙的光电催化活性,结果表明:N掺杂前后TiO2纳米管形貌相似,管径约90nm,N掺杂后TiO2对波长大于400nm的光吸收明显提高,并且吸收边界发生红移。氨水浓度为1.5mol/L时,制备的N掺杂TiO2纳米管电极对甲基橙的光电催化活性最高。对N掺杂机理进行了探讨。     

碳修饰二氧化钛纳米管的制备及其光催化性能研究

本文以钛酸丁酯为前躯体,蔗糖为碳源,采用溶胶-凝胶法和水热法相结合的方法制备了不同含量碳修饰的TiO2纳米管光催化剂(C/TiO2NTs)。通过元素分析(EA)、X射线衍射(XRD)、透射电镜(TEM)、N2吸附-脱附和紫外-可见漫反射吸收光谱(UV-vis-DRS)等手段对所制备的催化剂进行了表征分析。研究了C/TiO2NTs在紫外光及模拟日光条件下光催化降解甲基橙溶液的活性,并讨论了焙烧温度和碳含量对催化性能的影响。结果表明:碳修饰催化剂中的TiO2为锐钛矿型,碳修饰后使TiO2光催化剂的禁带宽度变窄,在可见光区吸收增强,可有效提高TiO2在紫外和可见光下的光催化活性,而且当焙烧温度为400℃,碳含量为0.90wt.%时,其光催化活性最好。     

C-N共掺杂纳米TiO2的制备及其光催化制氢活性

采用TiCN粉末在空气气氛中不同温度下焙烧制得C-N共掺杂的纳米TiO2光催化剂. 利用X射线衍射(XRD)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)以及X射线光电子能谱(XPS)等手段对其进行了表征. XRD和XPS结果表明, TiCN中的C和N元素可以被O取代得到C-N共掺杂的TiO2. DRS结果表明, 所制得的C-N共掺杂的TiO2在可见光区域比P25表现出更强的光吸收性能. 以Na2S-Na2SO3体系为牺牲剂, 分别考察了不同温度下焙烧得到的C-N共掺杂的TiO2光催化分解水产氢的活性. 结果表明, 550 ℃焙烧得到的C-N共掺杂的TiO2在紫外光照射下具有最高的光解水产氢活性,产氢速率为41.1 μmol·h-1, 大于P25的光解水产氢活性(26.2 μmol·h-1). 在紫外-可见光照射下, 光解水产氢速率仅为0.2 μmol·h-1, 这可能是由于C-N掺杂引起的可见光范围的吸收对光催化分解水产氢活性的贡献较小.     

Sm2O3掺杂TiO2光催化剂的制备和性能

 采用溶胶-凝胶法制备了Sm2O3掺杂TiO2光催化剂,通过X射线衍射、程序升温脱附和漫反射紫外-可见光谱等手段对催化剂进行了表征,并以苯酚为光催化降解反应模型化合物考察了光催化剂的活性,测定了苯酚在TiO2和Sm2O3掺杂TiO2光催化剂上的吸附常数. 结果表明,Sm2O3掺杂TiO2光催化剂具有较强的紫外光吸收性能. Sm2O3掺杂使TiO2粒径减小,比表面积增大,同时导致氧脱附温度提高及脱氧量增大. Sm2O3掺杂有利于反应底物在催化剂表面的吸附,Sm2O3的最佳掺入量为Sm/Ti摩尔比=0.8%.     

反应磁控溅射法制备的氮掺杂TiO2光催化膜的氮化学态和光催化活性

 采用中频交流磁控溅射法,以O2/N2混和气为反应气体,在铝片上沉积了氮掺杂TiO2膜. 利用原子力显微镜、紫外-可见光谱、X射线衍射和X射线光电子能谱等手段研究了掺杂膜的表面形貌、光吸收性能、物相组成以及膜样品中氮的化学态,并通过苯甲酰胺的光催化降解实验对光催化剂活性进行了评价. 结果表明,所得掺杂膜仅能够被紫外光所激发,反应气的配比对膜的形貌和TiO2的锐钛矿/金红石相比率均有影响,而氮在膜中以掺杂N3-、表面吸附N2和固溶N2的形式存在. 随着N3-掺入量的增加,掺杂膜的光催化活性显著提高,在反应气体组成为N2/(O2+N2)=80%(体积分数)时,掺杂N3-量为0.594%,苯甲酰胺光催化降解效果最好,其活性约为纯TiO2膜的1.5倍.     

Li+共掺杂对Er3+-Yb3+∶TiO2紫外、可见和红外发光同步增强研究

采用溶胶-凝胶(Sol-gel)法制备了Li+共掺杂的Er3+-Yb3+∶TiO2粉末。976 nm激光激发下在波长350~1700 nm范围内观察到了紫外、蓝色、绿色和红色上转换发光和红外下转换发光。随着Li+共掺杂浓度由0增大到20mol%,Er3+-Yb3+∶TiO2的紫外、可见和红外发光强度同步增强。低Li+共掺杂浓度引起的Li+固溶以及高Li+共掺杂浓度引起的相变过程相继破坏了Er3+的晶体场对称性,导致紫外、可见和红外发光显著增强。结果表明共掺杂Li+是一种提高Er3+掺杂材料发光性能的有效方法。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.