炭/多壁碳纳米管复合材料的制备与超级电容性能

结合环糊精包覆和热处理技术制备了炭/多壁碳纳米管(C/MWCNTs)复合材料, 并研究其应用于超级电容器的性能.利用扫描电子显微镜、透射电子显微镜、X射线衍射和拉曼光谱等技术对C/MWCNTs复合材料的形貌及结构进行分析.采用循环伏安和恒流充放电等电化学测试方法研究其电容特性.结果表明, C/MWCNTs复合材料具有良好的电化学性能, 远优于相应的炭及MWCNTs样品.在1 A/g电流密度下, 比电容可达到145 F/g, 循环3000次后, 容量无明显衰减.     

MnO_2/C复合材料的电化学电容特性研究

应用乙炔黑直接还原高锰酸钾制备MnO2/C复合材料.样品结构及性能由XRD和SEM表征.研究了MnO2/C电极(正极)在不同电解液中的法拉第"准电容行为",及其循环伏安、交流阻抗与恒电流充放电等性能.实验表明,MnO2/C复合材料具有良好的电化学电容特性.在1 mol/L的KOH电解液中和电流密度为5 mA/cm2下,MnO2/C复合材料的比电容量可达258 F/g,并表现出良好的循环性能.     

废旧锂离子电池基石墨烯/聚苯胺复合材料制备及其电化学性能研究

以废旧手机锂离子电池回收的负极石墨粉制备的氧化石墨烯(GO)和苯胺单体为原料,利用GO活化H_2O_2产生的·OH为氧化剂,采用原位复合法制备了不同质量比的石墨烯/聚苯胺复合材料,通过FTIR、XRD和SEM对其进行了表征,并利用循环伏安、交流阻抗、恒电流充放电等对其电化学性能进行测试。结果表明,该类石墨烯/聚苯胺复合材料具有良好的电化学性能,当电流密度为100mA/g时,质量比为1∶10制备的石墨烯/聚苯胺复合材料(rGO/PANI-10)的比电容达到481F/g,较石墨烯比容量(161F/g)提高了199%,较聚苯胺比容量(351F/g)提高了37%;在500mA/g电流密度下,rGO/PANI-10充放电循环1000圈后,电容保持率为77%,表现出较好的循环稳定性。     

CuO/石墨烯纳米片复合材料的制备及其电化学性能

利用改进的Hummers法制备氧化石墨,再通过化学沉淀法合成CuO/石墨烯纳米片(GNS)复合材料。经X射线衍射(XRD)、场发射扫描电镜(FESEM)、比表面积测试(BET)等表征了产物的组成、结构和形貌;通过循环伏安和恒电流充放电对复合材料的电化学性能进行了研究。在这种复合材料中,石墨烯作为导电骨架有利于增加CuO颗粒之间的导电性和材料的机械稳定性。复合材料在大电流放电中表现出优异的电化学性能,在10A/g的电流密度下,CuO/GNS-2的比电容可达276F/g,经1000次循环后比电容仍能保持86.5%,显示该复合材料具有优异的电化学性能。     

褐煤基多孔炭/CoNi_2S_4复合材料的制备及电容特性研究

以宝清褐煤为原料,使用KOH溶液萃取、活化后制得煤基多孔炭,并利用简单的水热法将褐煤基多孔碳与CoNi_2S_4复合,制备复合电容电极材料。考察了不同碳添加量对褐煤基多孔碳/CoNi_2S_4复合材料电化学性能的影响,结果表明,碳添加量过高或过低都不利于复合材料比电容的提升,而碳添加量为37%的褐煤基多孔碳/CoNi_2S_4复合材料具有较高的比电容和良好的循环性能,该复合电极在4 A/g电流密度下,比电容达到1318.2 F/g,在4000次充放电循环后电容保持率为80.9%。     

聚苯胺纳米刺/掺氮空心碳球复合材料的制备及电容性能

以掺氮空心碳球（N-HCS）为骨架,通过化学氧化聚合法制备了聚苯胺纳米刺/掺氮空心碳球复合材料（PANI/N-HCS）,采用扫描电子显微镜、透射电子显微镜和红外光谱仪等对样品的形貌、结构等进行了表征. 采用循环伏安、计时电位和交流阻抗等方法在1 mol/L H₂SO₄水溶液中考察了材料的电化学性能. 结果表明,PANI/N-HCS具有良好的电化学性能,在0.5 A/g电流密度下,PANI/N-HCS的比电容达346 F/g;当电流密度为20 A/g时,PANI/N-HCS比电容值为228 F/g,电容保持率为66%;在5 A/g电流密度下,经1000次充放电循环后,电容保持率为76%.     

快速混合法制备超级电容器用聚苯胺-活性炭复合材料

采用快速混合法制备聚苯胺-活性炭复合材料。通过扫描电镜、红外光谱等手段表征材料的形貌结构,通过恒流充放电、循环伏安和交流阻抗等技术测试了材料的电容特性。研究结果表明:制备的纯聚苯胺具有纳米纤维结构,但存在团聚问题;活性炭的加入抑制了纳米纤维之间的团聚,修饰了多孔形貌,降低了电荷传递阻抗,材料的功率特性得以改善,循环性能表现良好。当活性炭的用量为20%时,复合材料的比电容达371F/g,1 000次循环的比电容保持率为66.6%;电流密度由0.2A/g增加至1.5A/g,比电容下降小于5F/g。     

MnO2电沉积直立碳纳米管制备超级电容器

以直立碳纳米管为基底,以pH=6.0的0.1 mol/L Na2SO4为底液,采用电化学沉积法在0.2 mol/L Mn(CH3COO)2溶液中制备了直立碳纳米管与MnO2复合材料. SEM测试结果表明,复合材料表面呈现多孔状结构. 通过循环伏安、恒流充放电、交流阻抗等电化学方法对复合材料修饰电极进行电容性质测试. 结果表明,在1 mol/L KCl溶液中,0～0.6 V(vs.Ag/AgCl参比)电位窗口内此复合材料表现出优良的超电容性能. 直立碳纳米管电极的比电容为16 F/g,在碳纳米管表面沉积上MnO2修饰层后,复合材料电极的比电容增大至330 F/g,比电容量大幅提升近20倍. 同时扫描200圈后,直立碳纳米管与MnO2复合材料的循环伏安曲线变化很小,具有相当好的循环寿命和电容稳定性能.     

石墨烯/钴镍双氢氧化物复合材料的制备及其超电容特性

采用氧化石墨(GO)还原法制备石墨烯(GNS),以氨水为沉淀剂,在石墨烯存在的情况下,通过Co²⁺和Ni²⁺化学共沉积的方法合成了石墨烯/钴镍双氢氧化物复合电极材料,采用红外光谱(FT-IR)、X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、比表面积测试(BET)等技术手段表征了产物的组成、结构和形貌,用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。 研究发现,石墨烯纳米片均匀分散在钴镍双氢氧化物中,改善了钴镍双氢氧化物的传导性和结构稳定性。 电化学测试表明,在1 A/g的电流密度下,复合材料比电容高达2770 F/g,且循环500次后,比电容仍能保持93.4%,呈示该复合材料具有优异的电化学性能。     

MnO2电沉积直立碳纳米管制备超级电容器的研究

以直立碳纳米管为基底,以pH=6.0的0.1mol/L Na2SO4 为底液,采用电化学沉积法在0.2 mol/L Mn(CH3COO)2溶液中制备了直立碳纳米管与二氧化锰复合材料。SEM测试结果表明复合材料表面呈现多孔状结构。通过循环伏安,恒流充放电,交流阻抗等电化学方法对复合材料修饰电极进行电容性质测试。实验结果表明,在1mol/L KCl 溶液中,0-0.6V(vs. 银/氯化银参比)电位窗口内此复合材料表现出优良的超电容性能。直立碳纳米管电极的比电容为16 F/g,在碳纳米管表面沉积上二氧化锰修饰层后,此复合材料电极的比电容增大至330 F/g,比电容量大幅提升近20倍。同时扫描200圈后,直立碳纳米管与二氧化锰复合材料的循环伏安曲线变化很小,说明其具有相当好的循环寿命和电容稳定性能。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).