交联多孔结构的Mn2 掺杂聚苯胺/石墨烯复合材料的制备及超级电容特性

采用简单的原位氧化聚合法成功制备了Mn₂ 掺杂聚苯胺/石墨烯(Mn₂ -PANI/rGO)复合物电极材料,利用傅里叶变换红外(FT-IR)光谱、X射线衍射(XRD)、扫描电镜(FESEM)和电化学测试等手段对其结构、形貌和电化学电容性能进行了分析研究。结果表明,纳米棒状的锰离子掺杂态聚苯胺均匀分散在褶皱的石墨烯中,形成交联状的多孔结构;Mn₂ -PANI/rGO复合物具有高的比电容和优良的循环稳定性,当电流密度为2A/g时,电极的放电比容量高达952 F/g, 循环1000 次后初始比电容的保持率为86.2%,这表明过渡金属和石墨烯的加入增强了其电化学性能,高的比电容和好的速率使其复合物有望在超级电容器中有广泛的应用前景。     

石墨烯/聚苯胺复合材料的制备及其电化学性能

以苯胺和氧化石墨烯(GO)为原料, 采用电化学方法制备了石墨烯/聚苯胺(GP)复合材料. 利用X射线衍射(XRD)、扫描电镜(SEM)、拉曼(Raman)光谱、X射线光电子能谱分析(XPS)对其结构、微观形貌进行了表征,并对复合材料电化学性能进行了测试. 结果表明, 复合材料保持了石墨烯的基本形貌, 聚苯胺颗粒均匀地分散在石墨烯表面, 复合材料在500 mA·g^-1的电流密度下比电容达到352 F·g^-1, 1000 mA·g^-1下比电容为315 F·g^-1, 经过1000 次的充放电循环后容量保持率达到90%, 远大于石墨烯和聚苯胺单体的比电容. 复合材料放电效率高, 电解质离子易于在电极中扩散和迁移.     

自支撑三维功能化石墨烯/聚苯胺电极材料的制备及超级电容性能

采用水热法制备了三维石墨烯(3D-G),并以十八胺(ODA)为接枝剂对部分还原的氧化石墨烯进行氨基化处理,再利用原位聚合法在氨基化石墨烯表面生长聚苯胺,制备了十八胺功能化石墨烯/聚苯胺(G-ODA/PANI).对材料进行了结构表征、电化学性能分析和材料结构的比电容贡献分析.结果显示,电极材料的电容贡献大部分体现为材料的表面电容,G-ODA/PANI电极片在1 A/g电流密度时的比电容最高可达1080 F/g,是未功能化石墨烯/聚苯胺电极材料(G/PANI)的2.57倍,且循环稳定性也有很大的提高,循环10000周后的比容量保持率为90.8%,比G/PANI高9.6%.     

功能化石墨烯/聚苯胺复合电极材料的制备和电化学性能

利用水合肼还原十八胺(ODA)接枝的氧化石墨烯(GO),得到了十八胺功能化石墨烯(ODA-G),将ODAG与聚苯胺(PANI)通过溶液共混法,制备了功能化石墨烯和聚苯胺纳米复合材料(ODA-G/PANI).采用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、热重分析(TGA)、拉曼(Raman)光谱及透射电镜(TEM),对复合材料的结构和形貌进行了表征;利用循环伏安、恒流充放电及交流阻抗谱等,对复合材料的电化学性能进行了测试.结果显示,少量ODA-G的引入为PANI的电化学氧化还原反应提供了更多的电子通道和活性位置,有利于提高PANI的赝电容.在电流密度1.0 A·g-1下,2%(w)ODA-G/PANI的比电容达到787 F·g-1,而相应的PANI仅有426 F·g-1.此外,ODA-G/PANI的循环稳定性也远高于纯PANI.     

石墨烯/钴镍双氢氧化物复合材料的制备及其超电容特性

采用氧化石墨(GO)还原法制备石墨烯(GNS),以氨水为沉淀剂,在石墨烯存在的情况下,通过Co²⁺和Ni²⁺化学共沉积的方法合成了石墨烯/钴镍双氢氧化物复合电极材料,采用红外光谱(FT-IR)、X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、比表面积测试(BET)等技术手段表征了产物的组成、结构和形貌,用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。 研究发现,石墨烯纳米片均匀分散在钴镍双氢氧化物中,改善了钴镍双氢氧化物的传导性和结构稳定性。 电化学测试表明,在1 A/g的电流密度下,复合材料比电容高达2770 F/g,且循环500次后,比电容仍能保持93.4%,呈示该复合材料具有优异的电化学性能。     

NF/rGO/Co_3O_4/NiO电极的制备及在超级电容器中的应用

以泡沫镍(NF)为集流体,在优化好的电位、时间和浓度下,将还原氧化石墨烯(rGO)、金属氧化物(Co_3O_4和NiO)直接生长在泡沫镍上,制备了NF/rGO/Co_3O_4和NF/rGO/Co_3O_4/NiO电极.运用三电极体系对电极材料进行了恒流充放电(GCD)和交流阻抗(EIS)等测试.结果表明,复合材料NF/rGO/Co_3O_4/NiO具有较高的比容量(电流密度为2 A/g时,比容量达到1188.6 F/g)和较好的循环稳定性(2000周充放电后,稳定性达到80.5%).该材料还具有较高的倍率性能,当电流密度由2 A/g增至12 A/g时,倍率性能仍能达到75.7%.     

交联多孔结构Mn~(2+)掺杂聚苯胺/石墨烯复合材料的制备及超级电容特性

采用简单的原位氧化聚合法成功制备了Mn2+掺杂聚苯胺/还原氧化石墨烯(Mn2+-PANI/r GO)复合物电极材料,利用傅里叶变换红外光谱、X射线衍射、扫描电镜和电化学测试等手段对其结构、形貌和电化学电容性能进行了分析研究。结果表明,纳米棒状的锰离子掺杂态聚苯胺均匀分散在褶皱的石墨烯中,形成交联状的多孔结构。当电流密度为2A/g时,电极的放电比容量高达952 F/g,循环1000次后初始比电容的保持率为86.2%。过渡金属和石墨烯的加入提高了电极材料的电化学性能,高的比电容和优良的循环稳定性使Mn2+-PANI/r GO复合物在超级电容器中有很好的应用前景。     

磷酸钒锂/石墨烯复合正极材料的制备及表征

通过三聚氰胺甲醛树脂(MR)中的羟基与石墨烯氧化物(GO)中的羧基发生的沉淀反应来制备功能化的氧化石墨烯前驱体,然后利用溶胶-凝胶及高温热处理方法制备磷酸钒锂/石墨烯复合材料,利用此材料制备了电池电极,并对电极材料进行了结构和电化学表征。结果表明,所得磷酸钒锂为单斜晶系结构,石墨烯堆叠程度显著降低,也有效避免了磷酸钒锂颗粒的团聚,提高了材料的电化学性能。电池的充放电曲线极化较小,在3.0~4.3 V的区间内20 C倍率仍有86 mA·h/g的可逆容量。0.1 C循环100次后容量为119.7 mA·h/g,容量保持率94%。在3.0~4.8 V的高电压区间,10 C倍率下可逆容量80 mA·h/g,0.1 C循环100次后仍有145.6 mA·h/g的可逆容量。优异的循环和倍率性能以及较低的碳含量符合锂离子正极材料实用的要求。     

NiO/还原氧化石墨烯的溶剂热合成以及作为高循环稳定性超级电容器电极材料的性能表征

通过简单的溶剂热法以及其后续热处理过程,制备了NiO纳米花和NiO/还原氧化石墨烯(rGO)复合物。在NiO/rGO复合物中,rGO作为基底生长NiO,与此同时,NiO则有效的避免了rGO的团聚。采用热重分析(TG)、场发射扫描电子显微镜(FE-SEM)和X射线衍射对样品的成分、形貌和结构进行了表征。NiO/rGO复合物(NiO和rGO的质量比为82.7∶17.3)电极呈现优异的电化学性能。在1 A/g时,初始比电容为514.9 F/g,当材料完全活化后,其比电容高达600 F/g。同时,在电流密度为10 A/g时,相比于1 A/g时的比电容保持率为83.5%。此外,该电极材料具有非常优异的循环稳定性,6000次循环后电容衰减率为7.4%。表明所制备的复合物是一种有应用价值的超级电容器电极材料。     

CuO/GNS复合材料的制备及其电化学性能

利用改进的Hummers 法制备GO,采用化学沉淀法合成CuO/GNS复合材料,用X 射线衍射(XRD)、扫描电镜(FESEM)、比表面积测试(BET)等表征了产物的组成、结构和形貌;用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。结果显示：在这种复合材料中,石墨烯作为导电骨架,有利于增加氧化铜颗粒之间的导电性和材料的机械稳定性。大电流放电表现出优异的电化学性能,在 10 A.g_-1的电流密度下复合材料的比电容仍可达 276 F.g_-1,1000 次循环后比电容仍能保持86.5%,呈示该复合材料具有优异的电化学性能。     

Graphene materials preparation methods have dramatic influence upon their capacitance

Graphene related materials are widely expected to play a major role as materials for the construction of supercapacitors. We demonstrate here that graphene oxides prepared by various well-established methods exhibit dramatically different capacitances. We exfoliated graphite oxide sonographically to graphene oxide (GO) and we reduced GO by chemical or electrochemical means to chemically reduced graphene oxide (CRGO) and electrochemically reduced graphene oxide (ERGO); in addition, graphite oxide was thermally exfoliated leading to thermally reduced graphene oxide (TRGO). We found clear dependence of weight specific capacitance upon amount of oxygen containing groups presented on the surface of these graphenes. GO exhibits the lowest and TRGO the highest values of weight specific capacitance.     

氧化石墨烯的可控还原及结构表征

采用氧化还原法, 通过控制还原时间制备了不同还原程度的石墨烯; 用红外光谱、 紫外光谱、 拉曼光谱、 X射线衍射、 热重分析、 电导率测量等多种手段系统研究了不同还原程度石墨烯的结构与性能; 采用透射电子显微镜、 扫描电子显微镜和原子力显微镜比较了氧化石墨烯和石墨烯的形貌. 结果表明, 随着还原程度的增加, 石墨烯中含氧基团减少, 紫外吸收峰逐渐红移, D带与G带的强度比增加, 热稳定性和导电性提高. 微观结构表征说明石墨烯比氧化石墨烯片的厚度增加, 褶皱增多.     

Self-assembly of graphene oxide nanosheets in t-butanol/water medium under gamma-ray radiation

Graphene oxide (GO) nanosheets dispersed in strong acidic t-butanol/water medium can be reduced and self-assembled into a self-standing graphene hydrogel under γ-ray radiation, providing a facile and economical preparation method for hydroxylalkylated graphene-based aerogel.     

石墨烯纤维材料的化学气相沉积生长方法

石墨烯纤维材料是以石墨烯为主要结构基元沿某一特定方向组装而成或由石墨烯包覆纤维状基元形成的宏观一维材料。根据组成基元的不同可将石墨烯纤维材料分为石墨烯纤维和石墨烯包覆复合纤维。石墨烯纤维材料在一维方向上充分发挥了石墨烯高强度、高导电、高导热等特点,在智能纤维与织物、柔性储能器件、便携式电子器件等领域具有广阔的应用前景。随着化学气相沉积(Chemical Vapor Deposition,CVD)制备石墨烯薄膜技术的发展,CVD技术也逐渐应用于石墨烯纤维材料的制备。利用CVD法制备石墨烯纤维可避免传统纺丝工艺中繁琐的氧化石墨烯(Graphene Oxide,GO)还原过程。同时,通过CVD法直接将石墨烯沉积至纤维表面可以保证石墨烯与纤维基底之间强的粘附作用,提高复合纤维的稳定性,同时可实现对石墨烯质量的有效调控。本文综述了石墨烯纤维材料的CVD制备方法,石墨烯纤维材料优异的力学、电学、光学性质及其在智能传感、光电器件、柔性电极等领域的应用,并展望了CVD法制备石墨烯纤维材料未来的发展方向。     

石墨烯分散液及其组装膜的性能

通过对比表面活性剂十二烷基硫酸钠(SDS)和聚乙烯醇(PVA)对石墨烯的分散能力,发现SDS可有效避免石墨烯片层之间的团聚,使得石墨烯在水溶液中分散得更加均匀.将浓度分别为0.39和0.30 mg/m L的石墨烯(G)和石墨烯片(GF)的SDS分散液旋涂在ITO电极表面制备出G膜和GF膜.透射电子显微镜和原子力显微镜观测结果表明,两类石墨烯膜均呈现出纱状透明的片状结构,同时具有石墨烯特有的褶皱.在石墨烯膜上继续进行钌配合物分子膜的自组装实验,得到G/Ru复合膜和GF/Ru复合膜.采用循环伏安法及紫外-可见吸收光谱法对石墨烯复合膜进行光电化学分析,结果表明石墨烯膜与钌配合物分子膜的复合可有效加强薄膜对太阳光的吸收.     

Toward clean and crackless polymer-assisted transfer of CVD-grown graphene and its recent advances in GFET-based biosensors

Ever since the more than decade-old discovery of the mechanical exfoliation method for graphene isolation, this miraculous 2-dimensional material is still widely used in various applications because of its exceptional electron mobility and thermal conductivity. Graphene, commonly grown on a metallic substrate using chemical vapor deposition (CVD), needs to be transferred onto dielectric substrates compatible with complementary metal oxide–semiconductor (CMOS) technology for various electronic and optical applications. However, the ultra-clean transfer of graphene with defect-free is still crucial for large-area graphene devices' efficiency. This review introduces a comprehensive and up-to-date account of the transfer of the most attention kinds of CVD-grown graphene on copper substrates. The advances and main challenges of both wet and dry transfer methods are also carefully described. Particular emphasis is also given on graphene-based BioFET devices, revising their sensing mechanism and the optimum operational conditions toward high specificity and sensitivity. The authors have been convinced that upgrading the transfer process to accomplish the cleanest graphene surface and exploiting the optimum operating conditions will undoubtedly be of considerable significance to fabricate graphene-based devices.     

Electrochemistry Investigation on the Graphene/Electrolyte Interface

In this study, the graphene/electrolyte interface was investigated in detail by the electrochemical method. The total interface capacitance was calculated from the electrochemical impedance spectroscopy (EIS) results, and its responses to different concentrations and pHs were also investigated. The minimum point of the capacitance was found to shift to right (vs. Ag/AgCl) as the concentration increased, and to left with increasing pH. As a comparison, gold/electrolyte interface was investigated in the same way, but didn’t show the similar behavior. To further explore the interface capacitance, proper models were proposed to fit the EIS results. Two constant‐phase elements (CPE) were used in the graphene‐electrolyte interface model to represent the double‐layer capacitance (CPE_dl) and the quantum capacitance (CPE_q), respectively. The CPE_q exhibited its sensitivity to concentration and pH, while CPE_dl did not. This study gives a new aspect to detect concentration and pH, and may provide a reference for the graphene‐based supercapacitor research.     

酞菁铅在石墨烯表面吸附行为的拉曼光谱研究

利用石墨烯增强拉曼散射效应可以获得与石墨烯接触的某些分子的拉曼增强信号, 并且对于不同的分子或振动模, 其拉曼增强因子不同. 根据这一特征, 本工作利用拉曼光谱技术对石墨烯表面上酞菁铅(PbPc)分子Langmuir-Blodgett (LB)膜在退火过程中吸附构型的变化进行了跟踪研究. 发现随着退火温度的升高, 石墨烯表面上PbPc分子的拉曼信号经历了一个先增强后减弱的过程, 在升华温度点附近强度达到最大, 表明PbPc发生了由直立向平躺取向的转变; 同时, 在PbPc分子升华温度点附近, 由于对称性破坏导致散射截面低的振动模出现, 并且该振动模强度随着退火温度的进一步升高而增强, 表明非平面的PbPc分子受石墨烯π-π相互作用的影响而形变加剧, 向平面结构转变; 在更高的退火温度下, 则出现一些不属于PbPc分子的拉曼振动峰, 表明PbPc分子在石墨烯表面由Pb(II)被还原成Pb(0).     

BiPO4 photocatalyst employing synergistic action of Ag/Ag3PO4 nanostructure and graphene nanosheets

Graphene-supported BiPO₄/Ag/Ag₃PO₄ photocatalyst has been fabricated by simple hydrothermal and impregnation reaction. In BiPO₄/Ag/Ag₃PO₄ based on Reduced Graphene Oxide (RGO), this network renders numerous pathways for rapid mass transport, strong adsorption and multireflection of incident light; meanwhile, the interface between BiPO₄/Ag/Ag₃PO₄ and RGO increases the active sites and electron transfer rate. BiPO₄/Ag/Ag₃PO₄ based on RGO noticeably exhibited high photocatalytic activity than that of BiPO₄/Ag/Ag₃PO₄ and P25 under visible light irradiation for cationic dye (Rhodamine B), anionic dye (methyl orange) and 4-chlorophenol (4-CP) as a neutral pollutant, which are usually difficult to be degraded over the other catalysts. This enhanced photocatalytic activity of Graphene-supported BiPO₄/Ag/Ag₃PO₄ for all pollutants could be mainly ascribed to the reinforced charge transfer from BiPO₄/Ag/Ag₃PO₄ to RGO, which suppresses the recombination of electron/hole pairs. Besides that, this photocatalyst can be used repetitively with a high photocatalytic activity and no apparent loss of activity occurs. The results reveal that the RGO nanosheets work as a photocatalyst promoter during the photocatalytic reaction, leading to an improved photocatalytic activity.     

Comparative Studies on Electrocatalytic Activities of Chemically Reduced Graphene Oxide and Electrochemically Reduced Graphene Oxide Noncovalently Functionalized with Poly(methylene blue)

This study compares the electrocatalytic activities of chemically reduced graphene oxide (crGO) and electrochemically reduced graphene oxide (erGO), which are both noncovalently functionalized with a polyaromatic dye, poly(methylene blue) (polyMB), toward the oxidation of β‐nicotinamide adenine dinucleotide (NADH). PolyMB‐crGO and polyMB‐erGO composites were obtained via electropolymerization of methylene blue on crGO and GO modified glassy carbon (GC) electrodes, respectively. Cyclic voltammetry (CV) results indicate that these two types of integrated electrodes reveal different electrocatalytic activities. PolyMB‐crGO integrated electrode possesses lower catalytic oxidation potential, suggesting higher catalytic activity. The present study is helpful for the understanding and screening of graphene‐based advanced carbon nanomaterials for potential electrochemical applications.