ZrO2在Cu-ZnO-ZrO2甲醇水蒸汽重整制氢催化剂中的作用

通过对一系列Cu-ZnO-ZrO2甲醇水蒸汽重整(SRM)催化剂的XRD、TEM和BET表征及催化性能测定,研究催化剂中ZrO2对催化剂粒径、比表面以及对SRM反应性能的影响.结果表明,ZrO2的加入,使催化剂的粒径从15 nm降至10 nm（其中CuO和ZnO的平均粒径分别从7.7和10.4 nm降至3.9和8.7 nm）,BET比表面从60 m2•g－1增至78 m2•g－1.随着催化剂含ZrO2量不同,甲醇的转化率和H2、CO2的选择性均产生变化,当催化剂中Zr含量为24.0％(w),反应温度为220 ℃,水、醇摩尔比为1.3时,甲醇的转化率达到51.6％, H2和CO2的选择性达到100％(CO和CH4在产物气体中的体积分数小于10－4),这一结果对甲醇燃料电池甲醇重整器的应用具有重要的意义.     

金属壁载PdZn/Al2O3/FeCrAl催化剂上甲醇水蒸气重整制氢

研究了金属壁载PdZn/Al2O3/FeCrAl催化剂在不锈钢平板式微型制氢反应器中对甲醇水蒸气重整制氢的催化性能.结果表明,在反应温度为350℃,甲醇GHSV=1·6L/(g·h),水/醇摩尔比为1·2时,甲醇转化率可达100%,H2选择性达99%以上,出口CO含量低于0·5%,同时催化剂具有很好的稳定性.     

CuO-ZnO-ZrO_2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整(SRM)反应进行程序升温脱附(TPD)和程序升温表面反应(TPSR)研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4%、0.37%和0.17%时,甲酸根中间态的分解产物为CO、CO2和H2.     

甲醇水蒸气重整制氢CuO/CeO2-ZrO2/SiC整体催化剂的研究

采用浸渍法和溶胶凝胶法制备了CuO/CeO2-ZrO2/SiC整体催化剂,并将其用于甲醇水蒸气重整制氢反应中。结果表明,与CuO/CeO2-ZrO2颗粒催化剂相比,CuO/CeO2-ZrO2/SiC整体催化剂催化活性较好,产氢速率较快且重整气中CO体积分数较低。进一步探究了涂层涂覆量和CuO负载量对催化性能的影响,结果表明,当CeO2-ZrO2复合氧化物涂层涂覆量在15%±1%,CuO负载量为5%±1%时,催化性能较好;当反应温度为340℃,水醇物质的量比为1. 2,甲醇水蒸气气体空速为4840 h-1时,甲醇转化率为86. 0%,产氢速率为1490. 0 L/(m3·s),重整气中CO体积分数为1. 55%。最后通过单因素实验法探究了甲醇水蒸气气体空速、水醇物质的量比和反应温度对反应的影响。结果表明,随着气体空速变大,甲醇转化率下降,产氢速率上升,重整气中CO体积分数下降。随着水醇物质的量比增加,甲醇转化率先上升后下降,产氢速率先上升后下降,重整气中CO体积分数下降。随着反应温度的升高,甲醇转化率、产氢速率和重整气中CO体积分数均上升。     

铬助剂对Cu/ZrO_2/CNTs-NH_2催化剂催化CO_2加氢合成甲醇性能的影响

采用并流共沉淀方法制备了一系列不同铬含量的Cu/ZrO2/CNTs-NH2催化剂,在固定床反应器上考察铬对催化剂催化CO2加氢合成甲醇反应性能的影响.当铬含量为1%(w),反应温度为260°C,压力为3.0MPa,原料气组成为V(H2):V(CO2):V(N2)=69:23:8,空速为3600 mL·h-1·g-1时,催化剂的促进效果最显著,甲醇收率达7.78%.氮吸附、粉末X射线衍射(XRD)、氢气程序升温脱附(H2-TPR)、X射线光电子能谱(XPS)、二氧化碳程序升温脱附(CO2-TPD)、差热分析(DTA)以及扫描电子显微镜(SEM)等表征结果表明,随着铬含量的增加,铜颗粒的粒径减小,催化剂的比表面积增大.铬的加入一方面提高了铜的分散性,抑制了ZrO2的相变和活性组分的烧结;另一方面提高了CO2的吸附量并促进CO2由弱吸附向强吸附转化,从而提高甲醇的收率;但是当铬含量大于1%时,催化剂表面Cu、Zr的总含量明显下降,降低了CO2的吸附量并且形成了超强CO2吸附物种,抑制了CO2及其中间产物的转化,从而降低了甲醇收率.     

Zn0.2Zr0.8Ox固溶体催化剂的制备及其催化甲醇合成性能

以Zn(NO3)2·6H2O、Zr(NO3)4·5H2O为原料,Na2CO3为沉淀剂,采用并流共沉淀法制备了一系列不同Zn/Zr摩尔比的双金属氧化物催化剂,其结构经XRD、BET、Raman光谱、TEM和H2-TPR表征。结果表明:Zn0.2Zr0.8Ox催化剂为固溶体结构,比表面积最大达46.2 m^2·g^-1,还原性能良好。以催化CO2加氢合成甲醇为目标反应,对不同Zn/Zr摩尔比的催化剂进行性能测试,并考察了反应温度和反应时间对Zn0.2Zr0.8Ox催化剂性能的影响。结果表明:反应温度250℃、空速GHSV为12000 mL·g^-1h^-1、反应压力2 MPa和H2/CO2(体积比)=3/1时,Zn0.2Zr0.8Ox固溶体催化剂催化活性最高,二氧化碳转化率达到了3.5%、甲醇选择性高达75.4%,甲醇收率达到2.6%,且催化剂能够稳定运行100 h而不失活。     

球磨时间对浆态床CO甲烷化Ni-Al_2O_3催化剂性能的影响

结合行星式球磨机,采用低温固相法制备Ni-Al_2O_3催化剂,考察了球磨时间对Ni-Al_2O_3催化剂晶相结构(XRD)、还原特征(H2-TPR)、孔道结构(BET)、粒径分布(PSD)、表面形貌(SEM)和浆态床CO甲烷化性能的影响.结果表明,球磨时间为60 min,催化剂(CT-60)平均粒径最小,为141 nm;比表面积最大,为329 m2/g.随球磨时间延长,Ni-Al_2O_3催化剂的甲烷化性能(CO转化率、CH_4选择性和CH_4收率)均先增加后减少.其中,球磨时间为60 min制备的催化剂(CT-60)甲烷化性能最佳,其CO转化率、CH_4选择性和CH_4收率分别达87.9%、8 6.8%和74.3%.结合催化剂表征可知,CT-60优异的性能与其具有较小的颗粒尺寸(141 nm)和较大的比表面积(329 m2·g-1)有很大的关联.即,催化剂颗粒尺寸越小,比表面积越大,其性能越好.     

CuO-ZnO-ZrO2催化甲醇水蒸汽重整反应机理和中间态

应用质谱在线技术,对CuO-ZnO-ZrO2催化甲醇水蒸汽重整（SRM）反应进行程序升温脱附（TPD）和程序升温表面反应（TPSR）研究.结果表明:在反应态催化剂表面,甲醇以分子吸附态形式存在,甲醇水蒸汽重整反应经历甲酸根中间物种.分别用CuO、CuO-ZnO、CuO-ZnO-ZrO2作催化剂,甲醇在气流中的摩尔分数分别高于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO2和H2;而甲醇在气流中的摩尔分数分别低于5.4％、0.37％和0.17％时,甲酸根中间态的分解产物为CO、CO2和H2.     

湿混法制备甲醇氧化重整制氢CuZnAlZr催化剂

用简易湿混法制备了用于甲醇氧化重整制氢的CuZnAlZr催化剂,与共沉淀法制备的催化剂比较,结果表明,湿混法制备的催化剂具有相当的中高温活性和略低的低温活性,有较高的CO2选择性。XRD、TPR、TG-DSC等表征结果显示,湿混法制备的催化剂中铜组分易于向表面迁移和富集,并可能与氧化铝作用生成铜铝复合氧化物,具有了更高的Cu分散度和Cu0比表面浓度。湿混法制备的催化剂对甲醇氧化重整反应有较好的稳定性,经100 h的连续反应,在275 ℃时甲醇转化率在90％以上,重整气中氢气体积分数大于60％,CO2选择性接近99％。     

水凝胶法制备Ni/ZrO2催化剂及催化CO2加氢甲烷化性能

采用水凝胶法制备出一系列Ni/ZrO2催化剂,使用X射线衍射(XRD),比表面积(BET)测试,透射电子显微镜(TEM)和氢气程序升温还原(H2-TPR)对其结构进行了表征,并考察了在CO2加氢甲烷化反应中的催化活性.研究结果表明,经过450℃焙烧的催化剂中ZrO2呈无定形结构,NiO均匀分散在ZrO2表面上;在400℃时H2还原过程中,部分无定形ZrO2转变为四方晶相结构并使Ni再次分散,Ni与ZrO2之间的电子作用抑制了Ni晶粒的生长和ZrO2晶型的转变;与无定形ZrO2和四方相ZrO2产生电子作用的NiO对催化剂活性起决定性作用,当Ni/Zr摩尔比为0.707时,催化剂活性最高.在H2/CO2体积比为4,空速为1×104h-1,压力为0.5 MPa,反应温度为200℃时,CO2转化率达到27%以上,当反应温度上升至280~320℃时,CO2转化率达到99%以上,CH4选择性大于92%.     

Syntheses of 2-hydroperoxy-and 2-hydroxy-2H-imidazoles

Oxidation of fully substituted imidazoles 1 by singlet oxygen gives in good yield fully substituted 2-hydroperoxy-2H-imidazoles 2 . Reduction of 2 by triphenylphosphine leads to 2-hydroxy-2H-irnidazoles 3 . Limitations of the methods are reported.     

Crystal Structures of [Bu2Sn(O2PPh2)2], [Ph2Sn(O2PPh2)2], and [PhClSn(O2PPh2)OMe]2. Raman Spectra of [Ph2Sn(O2PPh2)2] and [PhClSn(O2PPh2)OMe]2

[(n‐Bu)₂Sn(O₂PPh₂)₂] ( 1 ), and [Ph₂Sn(O₂PPh₂)₂] ( 2 ) have been synthesized by the reactions of R₂SnCl₂ (R=n‐Bu, Ph) with HO₂PPh₂ in Methanol. From the reaction of Ph₂SnCl₂ with diphenylphosphinic acid a third product [PhClSn(O₂PPh₂)OMe]₂ ( 3 ) could be isolated. X‐ray diffraction studies show 1 to crystallize in the monoclinic space group P2₁/c with a = 1303.7(1) pm, b = 2286.9(2) pm, c = 1063.1(1) pm, β = 94.383(6)°, and Z = 4. 2 crystallizes triclinic in the space group , the cell parameters being a = 1293.2(2) pm, b = 1478.5(4) pm, c = 1507.2(3) pm, α = 98.86(3)°, β = 109.63(2)°, γ = 114.88(2)°, and Z = 2. Both compounds form arrays of eight‐membered rings (SnOPO)₂ linked at the tin atoms to form chains of infinite length. The dimer 3 consists of a like ring, in which the tin atoms are bridged by methoxo groups. It crystallizes triclinic in space group with a = 946.4(1) pm, b = 963.7(1) pm, c = 1174.2(1) pm, α = 82.495(6)°, β = 66.451(6)°, γ = 74.922(6)°, and Z = 1 for the dimer. The Raman spectra of 2 and 3 are given and discussed.     

Electrochemical study of (NEt4)2Cl2FeS2MoS2 and (NEt4)2Cl2FeS2MoS2FeCl2

Summary The ability of [MoS₄]^2–, anions to be used as ligands for transition metal ions has been widely demonstrated, especially with Fe²⁺. The present study has been restricted to linear complexes such as (NEt₄)₂ [Cl₂FeS₂MoS₂] and (NEt₄)₂[Cl₂FeS₂MoS₂FeCl₂]. Their electrochemical properties are described: upon electrochemical reduction, these compounds yield MoS₂, as a black precipitate, and an iron complex in solution, assumed to be [SFeCl₂]^2–. The electrochemical reduction goes through two electron transfers, coupled with the breakdown of the molecular skeleton: a DISPl and an ECE mechanism. Depending on the solvent, the following equilibrium may be observed: [Cl₄Fe₂MoS₄]^2–[Cl₂FeMoS₄]^2–+FeCl₂. The equilibrium constant, K_D, was evaluated by differential pulse polarography. K_D is tightly related to the donor number of the solvent.     

Photocycloaddition of 2-Cyanocycloalk-2-Enones to 2, 3-Dimethylbut-2-Ene

Irradiation of 5,5-dimethyl-6-oxocyclohex- l-ene- l-carbonitrile ( 1 ) in the presence of 2,3-dimethylbut-2-ene afforded 3,3,4,4,7,7-hexamethyl-3,4,4a,5,6,7-hexahydroindeno[1,7-c,d]-],2-oxazole (3) in nearly quantitative yield. In contrast, 4,4-dimethyl-5-oxo-cyclopent-l-ene-l-carbonitrile ( 2 ) under the same conditions reacted not to a tricyclic isoxazole but to a 2:1 mixture of 3,3,6,6,7,7-hexamethyl-2-oxo-bicyclo[3.2.0]heptane-l-carbonitrile ( 4 ) and trans-3,3-dimethyl-2-oxo-5-(2,3-dimethylbut-3-en-2-yl)cyclopentane-l-carbonitrile ( 5 ), respectively.     

Thermal decomposition of Me3SnO2PCl2, Me2Sn(O2PCl2)2 and Ph3SnO2PCl2

TG and DTA studies on Me₃SnO₂PCl₂, Me₂Sn(O₂PCl₂)₂ and Ph₃SnO₂PCl₂ were carried out under dynamic argon atmosphere. The results show that the decomposition proceeds in different stages leading to the formation of Sn₃(PO₄)₂ as a stable product. This compound was characterized by IR spectroscopy. Decomposition schemes involving reductive elimination reactions were proposed.     

Efficient C2 functionalisation of 2H-2-imidazolines

Alkylation and oxidation of 2H-2-imidazolines, followed by regioselective deprotection, thionation and microwave-assisted Liebeskind-Srogl reaction, efficiently led to 2-aryl-2-imidazolines as new analogues of p53-hdm2 interaction inhibitors (Nutlins).