Cost‐Effective,High‐Performance Porous‐Organic‐Polymer Conductors Functionalized with Sulfonic Acid Groups by Direct Postsynthetic Substitution

We demonstrate the facile microwave‐assisted synthesis of a porous organic framework 1 and the sulfonated solid ( 1S ) through postsubstitution. Remarkably, the conductivity of 1S showed an approximately 300‐fold enhancement at 30 °C as compared to that of 1 , and reached 7.72×10⁻² S cm⁻¹ at 80 °C and 90 % relative humidity. The superprotonic conductivity exceeds that observed for any conductive porous organic polymer reported to date. This material, which is cost‐effective and scalable for mass production, also revealed long‐term performance over more than 3 months without conductivity decay.     

Hydrogen‐Bonded Organic Frameworks (HOFs): A New Class of Porous Crystalline Proton‐Conducting Materials

Two porous hydrogen‐bonded organic frameworks (HOFs) based on arene sulfonates and guanidinium ions are reported. As a result of the presence of ionic backbones appended with protonic source, the compounds exhibit ultra‐high proton conduction values (σ) 0.75× 10^?2 S cm^?1 and 1.8×10^?2 S cm^?1 under humidified conditions. Also, they have very low activation energy values and the highest proton conductivity at ambient conditions (low humidity and at moderate temperature) among porous crystalline materials, such as metal–organic frameworks (MOFs) and covalent organic frameworks (COFs). These values are not only comparable to the conventionally used proton exchange membranes, such as Nafion used in fuel cell technologies, but is also the highest value reported in organic‐based porous architectures. Notably, this report inaugurates the usage of crystalline hydrogen‐bonded porous organic frameworks as solid‐state proton conducting materials.     

A Three‐Dimensional Porous Organic Semiconductor Based on Fully sp2‐Hybridized Graphitic Polymer

Dimensionality plays an important role in the charge transport properties of organic semiconductors. Although three‐dimensional semiconductors, such as Si, are common in inorganic materials, imparting electrical conductivity to covalent three‐dimensional organic polymers is challenging. Now, the synthesis of a three‐dimensional π‐conjugated porous organic polymer (3D p‐POP) using catalyst‐free Diels–Alder cycloaddition polymerization followed by acid‐promoted aromatization is presented. With a surface area of 801 m² g^?1, full conjugation throughout the carbon backbone, and an electrical conductivity of 6(2)×10^?4 S cm^?1 upon treatment with I₂ vapor, the 3D p‐POP is the first member of a new class of permanently porous 3D organic semiconductors.     

Water‐Stable Homochiral Cluster Organic Frameworks Built by Two Kinds of Large Tetrahedral Cluster Units

Compared with metal organic frameworks (MOFs), the proton conductivity of cluster organic frameworks has been less studied. Herein, two supertetrahedral cluster organic frameworks (SCOFs) have been made that show two‐fold interpenetrated networks built by trivalent lanthanide tetrahedral clusters and monovalent cuprous T₃‐supertetrahedral clusters. The structure analysis, second harmonic generation signals, and solid‐state circular dichroism spectroscopy consistently reveal the chirality of these SCOFs. Remarkably, the water‐stable SCOFs show a high proton conductivity value of 1.4×10^?3 S cm^?1 at 80 °C and 95 % RH (relative humidity).     

Single Lithium‐Ion Conducting Polymer Electrolytes Based on a Super‐Delocalized Polyanion

A novel single lithium‐ion (Li‐ion) conducting polymer electrolyte is presented that is composed of the lithium salt of a polyanion, poly[(4‐styrenesulfonyl)(trifluoromethyl(S‐trifluoromethylsulfonylimino)sulfonyl)imide] (PSsTFSI^?), and high‐molecular‐weight poly(ethylene oxide) (PEO). The neat LiPSsTFSI ionomer displays a low glass‐transition temperature (44.3 °C; that is, strongly plasticizing effect). The complex of LiPSsTFSI/PEO exhibits a high Li‐ion transference number (t_Li⁺=0.91) and is thermally stable up to 300 °C. Meanwhile, it exhibits a Li‐ion conductivity as high as 1.35×10^?4 S cm^?1 at 90 °C, which is comparable to that for the classic ambipolar LiTFSI/PEO SPEs at the same temperature. These outstanding properties of the LiPSsTFSI/PEO blended polymer electrolyte would make it promising as solid polymer electrolytes for Li batteries.     

Electrical Properties of Sm‐doped Ceria (SDC) and SDC Carbonate Composite

This study prepared a dense Sm‐doped ceria (SDC) and an SDC carbonate composite (abbreviated as SDC‐C). The latter was prepared by immersing porous SDC with a formula of (Ce_0.8Sm_0.2)O_1.9 and a relative density of approximately 65‐70% into a molten mixture of carbonates containing 1:1 molar ratio of Li₂CO₃ and Na₂CO₃ at 500 °C. The relative density of the SDC‐C was close to 100%. In addition, SDC oxide without carbonates, which also has a relative density of close to 100%, was heat treated at 1600 °C. At 500 °C, the electrical conductivity and ionic transference number (t_i) of the SDC oxide were 1.79(5) × 10^?3 S·cm^?1 and 0.99(2), respectively, such that electronic conduction could be disregarded. Increasing the temperature caused a gradual decrease in the t_i of SDC. Following the addition of carbonates to SDC, the electrical conductivity reached 1.23(9) × 10^?1 S·cm^?1 at 500 °C. After 14 days (340 h), the electrical conductivity of the SDC‐C at 490 °C, leveled off at about 6 × 10^?2 S·cm^?1. SDC‐C could be used as a potential electrolyte in solid oxide fuel cells (SOFCs) at temperatures below 500 °C.     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

Polystyrene Sulfonate Threaded through a Metal–Organic Framework Membrane for Fast and Selective Lithium‐Ion Separation

Extraction of lithium ions from salt‐lake brines is very important to produce lithium compounds. Herein, we report a new approach to construct polystyrene sulfonate (PSS) threaded HKUST‐1 metal–organic framework (MOF) membranes through an in situ confinement conversion process. The resulting membrane PSS@HKUST‐1‐6.7, with unique anchored three‐dimensional sulfonate networks, shows a very high Li⁺ conductivity of 5.53×10^?4 S cm^?1 at 25 °C, 1.89×10^?3 S cm^?1 at 70 °C, and Li⁺ flux of 6.75 mol m^?2 h^?1, which are five orders higher than that of the pristine HKUST‐1 membrane. Attributed to the different size sieving effects and the affinity differences of the Li⁺, Na⁺, K⁺, and Mg²⁺ ions to the sulfonate groups, the PSS@HKUST‐1‐6.7 membrane exhibits ideal selectivities of 78, 99, and 10296 for Li⁺/Na⁺, Li⁺/K⁺, Li⁺/Mg²⁺ and real binary ion selectivities of 35, 67, and 1815, respectively, the highest ever reported among ionic conductors and Li⁺ extraction membranes.     

Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

Polymer electrolyte membranes based on p‐toluenesulfonic acid doped poly(1‐vinyl‐1,2,4‐triazole): Synthesis,thermal and proton conductivity properties

Throughout this work, the synthesis, thermal as well as proton conducting properties of acid doped heterocyclic polymer were studied under anhydrous conditions. In this context, poly(1‐vinyl‐1,2,4‐triazole), PVTri was produced by free radical polymerization of 1‐vinyl‐1,2,4‐triazole with a high yield. The structure of the homopolymer was proved by FTIR and solid state ¹³C CP‐MAS NMR spectroscopy. The polymer was doped with p‐toluenesulfonic acid at various molar ratios, x = 0.5, 1, 1.5, 2, with respect to polymer repeating unit. The proton transfer from p‐toluenesulfonic acid to the triazole rings was proved with FTIR spectroscopy. Thermogravimetry analysis showed that the samples are thermally stable up to ～250 °C. Differential scanning calorimetry results illustrated that the materials are homogeneous and the dopant strongly affects the glass transition temperature of the host polymer. Cyclic voltammetry results showed that the electrochemical stability domain extends over 3 V. The proton conductivity of these materials increased with dopant concentration and the temperature. Charge transport relaxation times were derived via complex electrical modulus formalism (M*). The temperature dependence of conductivity relaxation times showed that the proton conductivity occurs via structure diffusion. In the anhydrous state, the proton conductivity of PVTri1PTSA and PVTri2PTSA was measured as 8 × 10^?4 S/cm at 150 °C and 0.012 S/cm at 110 °C, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1016–1021, 2010     

pH‐Dependent Proton Conducting Behavior in a Metal–Organic Framework Material

A porous metal–organic framework (MOF), [Ni₂(dobdc)(H₂O)₂]?6 H₂O (Ni₂(dobdc) or Ni‐MOF‐74; dobdc^4?=2,5‐dioxido‐1,4‐benzenedicarboxylate) with hexagonal channels was synthesized using a microwave‐assisted solvothermal reaction. Soaking Ni₂(dobdc) in sulfuric acid solutions at different pH values afforded new proton‐conducting frameworks, H⁺@Ni₂(dobdc). At pH 1.8, the acidified MOF shows proton conductivity of 2.2×10^?2 S cm^?1 at 80 °C and 95 % relative humidity (RH), approaching the highest values reported for MOFs. Proton conduction occurs via the Grotthuss mechanism with a significantly low activation energy as compared to other proton‐conducting MOFs. Protonated water clusters within the pores of H⁺@Ni₂(dobdc) play an important role in the conduction process.     

Phosphoric acid‐doped imidazolium ionomers with enhanced stability for anhydrous proton‐exchange membrane applications

Phosphoric acid‐doped crosslinked proton‐conducting membranes with high anhydrous proton conductivity, and good chemical stability in phosphoric acid were synthesized and characterized. The synthetic procedure of the acid‐doped composite membranes mainly involves the in situ crosslinking of polymerizable monomer oils (styrene and acrylonitrile) and vinylimidazole, and followed by the sulfonation of pendant imidazole groups with butanesultone, and further doped with phosphoric acid. The resultant phosphoric acid‐doped composite electrolyte membranes are flexible and show high thermal stability and high‐proton conductivity up to the order of 10^?2 S cm^?1 at 160 °C under anhydrous conditions. The phosphoric acid uptake, swelling degree, and proton conductivity of the composite membranes increase with the vinylimidazole content. The resultant composite membranes also show good oxidative stability in Fenton's reagent (at 70 °C), and quite good chemical stability in phosphoric acid (at 160 °C). The properties of the prepared electrolyte membranes indicate their promising prospects in anhydrous proton‐exchange membrane applications. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013 , 51, 1311–1317     

Guest‐Assisted Proton Conduction in the Sulfonic Mesoporous MIL‐101 MOF

Post‐synthesis modification of MIL‐101(Cr)‐NO₂ was explored in order to decorate the organic backbone by propyl‐sulfonic groups, with the aim to incorporate mobile and acidic protons for solid‐state proton electrolyte applications. The resulting solid switched from insulating towards proton superconductive behavior under humidity, while the conductivity recorded at 363 K and 95 % relative humidity reached 4.8×10^?3 S cm^?1. Propitiously, the impregnation of the material by strong acidic molecules (H₂SO₄) further boosted the proton conductivity performances up to the remarkable σ value of 1.3×10^?1 S cm^?1 at 363 K/95 % RH, which reaches the performances of the best proton conductive MOF reported so far.     

Preparation of porous polyimide/in‐situ reduced graphene oxide composite films for electromagnetic interference shielding

Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m^?1 and excellent specific shielding efficiency value of 693 dB cm² g^?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and characterization of anion‐exchange membranes derived from poly(vinylbenzyl chloride‐co‐styrene) and intercalated montmorillonite

In this paper, three organic intercalating agents containing cations [hexadecyl trimethyl ammonium bromide (CTAB), poly(acrylamide‐co‐diallyldimethylammonium chloride), and quaternized polyethyleneimine] are used to prepare intercalated montmorillonites (MMT) by ion‐exchange method. Then the modified MMTs are doped with vinylbenzyl chloride and styrene copolymer [poly(vinylbenzyl chloride‐co‐styrene)] for fabricating composite anion‐exchange membranes (AEM). Fourier transform infrared, X‐raydiffraction, thermogravimetric analysis, scanning electron microscopy, and Mastersizer laser particle size analyzer are employed to characterize the structure and morphology of MMTs and AEMs. The successful intercalation of MMTs is approved, and the MMT intercalated by CTAB shows an interlayer distance of 2.31 nm. The properties of the composite membranes including water uptake, mechanical property, and ionic conductivity are investigated. Among all the AEMs, the composite membrane containing MMT sheets with CTAB demonstrates better compositive performances. It presents an ionic conductivity of 2.09 × 10^?2 S cm^?1 at 80°C and good alkaline solution stability. Copyright © 2016 John Wiley & Sons, Ltd.     

Novel polymer electrolytes prepared by copolymerization of ionic liquid monomers

Ionic liquid monomer couples were prepared by the neutralization of 1‐vinylimidazole with vinylsulfonic acid or 3‐sulfopropyl acrylate. These ionic liquid monomer couples were viscous liquid at room temperature and showed low glass transition temperature (Tg) at ?83 °C and ?73 °C, respectively. These monomer couples were copolymerized to prepare ion conductive polymer matrix. Thus prepared ionic liquid copolymers had no carrier ions, and they showed very low ionic conductivity of below 10^?9 S cm^?1. Equimolar amount of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) to imidazolium salt unit was then added to generate carrier ions in the ionic liquid copolymers. Poly(vinylimidazolium‐co‐vinylsulfonate) containing equimolar LiTFSI showed the ionic conductivity of 4 × 10^?8 S cm^?1 at 30 °C. Advanced copolymer, poly(vinylimidazolium‐co‐3‐sulfopropyl acrylate) which has flexible spacer between the anionic charge and polymer main chain, showed the ionic conductivity of about 10^?6 S cm^?1 at 30 °C, which is 100 times higher than that of copolymer without spacer. Even an excess amount of LiTFSI was added, the ionic conductivity of the copolymer kept this conductivity. This tendency is completely different from the typical polyether systems. Copyright © 2002 John Wiley & Sons, Ltd.     

Allyl ethers as combined plasticizing and crosslinkable side groups in polycarbonate‐based polymer electrolytes for solid‐state Li batteries

Allyl ether‐functional polycarbonates, synthesized by organocatalytic ring‐opening polymerization of the six‐membered cyclic carbonate monomer 2‐allyloxymethyl‐2‐ethyltrimethylene carbonate, were used to prepare non‐polyether polymer electrolytes. UV‐crosslinking of the allyl side groups provided mechanically stable electrolytes with improved molecular flexibility—T_g below ?20 °C—and higher ionic conductivity—up to 4.3 × 10^?7 S/cm at 25 °C and 5.2 × 10^?6 S/cm at 60 °C—due to the plasticizing properties of the allyl ether side groups. The electrolyte function was additionally demonstrated in thin‐film Li battery cells. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2128–2135     

Polycarboxylate‐Templated Coordination Polymers: Role of Templates for Superprotonic Conductivities of up to 10−1 S cm−1

Three coordination polymers (CPs) have been synthesized based on a [Co(bpy)(H₂O)₄]²⁺ chain (bpy=4,4′‐bipyridine) by a template approach. The frameworks are neutralized by different templated polycarboxylate anions (furan di‐carboxylate (fdc) in Co‐fdc, benzene tri‐carboxylate (btc) in Co‐tri and benzene tetra‐carboxylate (btec) in Co‐tetra). These templates with different degrees of protonation and ionic carrier concentration played significant role on crystal packing as well as formation of well‐directed H‐bonded networks which made these CPs perform well in proton conduction (PC). The PC value reaches to 1.49×10^?1 S cm^?1 under 80 °C and 98 % relative humidity (R.H.) for Co‐tri, which is the highest among CPs/MOFs/COFs and is an example of conductivity in the order of 10^?1 S cm^?1. Co‐tri and Co‐tetra are excellent proton conductors at mild temperature (40 °C) and 98 % R.H. (conductivities up to 2.92×10^?2 and 1.38×10^?2 S cm^?1, respectively).     

Solvent‐Vapor‐Induced Reversible Single‐Crystal‐to‐Single‐Crystal Transformation of a Triphosphaazatriangulene‐Based Metal–Organic Framework

A triphosphaazatriangulene (H₃L) was synthesized through an intramolecular triple phospha‐Friedel–Crafts reaction. The H₃L triangulene contains three phosphinate groups and an extended π‐conjugated framework, which enables the stimuli‐responsive reversible transformation of [Cu(HL)(DMSO)?(MeOH)]_n, a 3D‐MOF that exhibits reversible sorption characteristics, into (H₃L?0.5 [Cu₂(OH)₄?6 H₂O] ?4 H₂O), a 1D‐columnar assembled proton‐conducting material. The hydrophilic nature of the latter resulted in a proton conductivity of 5.5×10^?3 S cm^?1 at 95 % relative humidity and 60 °C.     

Superprotonic Conductivity of a UiO‐66 Framework Functionalized with Sulfonic Acid Groups by Facile Postsynthetic Oxidation

Facile postsynthetic oxidation of the thiol‐laced UiO‐66‐type framework UiO‐66(SH)₂ enabled the generation of UiO‐66(SO₃H)₂ with sulfonic acid groups covalently linked to the backbone of the system. The oxidized material exhibited a superprotonic conductivity of 8.4×10^?2 S cm^?1 at 80 °C and 90 % relative humidity, and long‐term stability of the conductivity was observed. This level of conductivity exceeds that of any proton‐conducting MOF reported to date and is equivalent to the conductivity of the most effective known electrolyte, Nafion.