A simple broadband T-shaped waveguide branch in photonic crystals

A simple broadband T-shaped waveguide branch in photonic crystals is constructed only by introducing three dielectric rods into the waveguide channels near branch region. Numerical results indicate that the bandwidth of high transmission (the total transmittance is larger than 95%) is over 415 nm centered at 1550 nm. Owing to its simple structure and broad enough bandwidth, this waveguide branch is expected to be applied to highly dense photonic integrated circuits.     

含双T形量子结构的量子波导中声学声子输运和热导

采用散射矩阵方法, 研究了含双T形量子结构的量子波导中声学声子输运和热导性质. 结果表明: 在极低温度, 双T形量子结构能增强低温热导; 相反地, 在相对较高的温度范围, 双T形量子结构能降低低温热导. 而在整个低温范围内, 增加散射区域最窄处的宽度能增强低温热导. 计算结果表明可以通过调节含双T形量子结构的量子波导结构来调控声子的输运概率和热导. 关键词： 声学声子输运 热导 量子结构     

数值模拟二维间隙表面等离子波导传输特性

利用表面等离子激元的新颖特性,设计了二维间隙表面等离子波导.以这种结构为基础通过变形和组合形成90°直角弯曲波导、T型光功率分配器和光开光,采用时域有限差分法研究了它们的传输特性.结果表明:不同于介质光波导的弯曲损耗来自于辐射泄漏,90°直角弯曲间隙表面等离子波导的能量损耗主要来自于金属中的欧姆热损耗.在间隙达到40 nm以上后,当直行段的长度适当时,弯曲段的透射率较相同长度的直波导的透射率要大.T型光功率分配器在两输出波导的间隙宽度比达到0.6及以上时,不同于传统介质波导的分光原则,能量主要沿等效折射率较小的输出臂流出.当两输入光的相位反相时,T型光开关处于输出截止的状态,当两输入光的相位同相时,T型光开关处于输出导通的状态.所有波导间隙均小于衍射极限,实现了超衍射极限传播,可用于未来了超大规模集成光路中.     

A ceramics-free waveguide for ITER ion cyclotron wave system

A ceramics-free waveguide for the high-power International Thermonuclear Experimental Reactor ion cyclotron (ITER IC) system (15-80 MHz), which is a TEM waveguide supported mechanically by T-shaped ridged waveguides, is proposed. The transmission-line theory shows that this waveguide has power handling capability of more than 3 MW, where an optimized antenna impedance is used for the ITER plasma parameters. The transmission line model used for the analysis is verified by the experiments on a one-tenth scale model     

T-shaped dielectric slot waveguides for efficient control of birefringence and polarization independent directional coupling

A novel dielectric slot waveguide supporting strongly confined field in a T-shaped low-index slot region for both TE and TM polarizations is proposed and analyzed. Numerical simulations have demonstrated that quite different birefringent modal properties are achievable with tight optical confinement in the slot by tuning key geometrical parameters of the waveguide. Based on such a slot structure, the characteristics of directional couplers are investigated and the conditions for polarization independent coupling are also given. The presented T-shaped slot waveguide might be employed in integrated photonic systems as important building blocks enabling a number of potential applications.     

Trapped modes in finite quantum waveguides

The eigenstates of an electron in an infinite quantum waveguide (e.g., a bent strip or a twisted tube) are often trapped or localized in a bounded region that prohibits the electron transmission through the waveguide at the corresponding energies. We revisit this statement for resonators with long but finite branches that we call ??finite waveguides??. Although the Laplace operator in bounded domains has no continuous spectrum and all eigenfunctions have finite L ₂ norm, the trapping of an eigenfunction can be understood as its exponential decay inside the branches. We describe a general variational formalism for detecting trapped modes in such resonators. For finite waveguides with general cylindrical branches, we obtain a sufficient condition which determines the minimal length of branches for getting a trapped eigenmode. Varying the branch lengths may switch certain eigenmodes from non-trapped to trapped or, equivalently, the waveguide state from conducting to insulating. These concepts are illustrated for several typical waveguides (L-shape, bent strip, crossing of two strips, etc.). We conclude that the well-established theory of trapping in infinite waveguides may be incomplete and require further development for applications to finite-size microscopic quantum devices.     

A Defect Effect to Light Transmission through Acute Bending Coupled Cavity Waveguide in a Two-Dimensional Photonic Crystal

Light propagation through a coupled-defect waveguide with a 63.5° bend in a two-dimensional （2D） photonic crystal is investigated. The waveguide modes are non-degenerate monopole state and dipole defect state of a square lattice for two different branches. To increaze the transmission in the bending waveguide, we propose a method to rotate the localized state by introducing a cavity. The higher coupling efficiency and transmission shift. new type defect with a sheared square rod into coupled in the bending waveguide are obtained with proper shear     

Design of tunable surface mode waveguide based on photonic crystal composite structure using organic liquid

With the method of replacing the surface layer of photonic crystal with tubes, a novel photonic crystal composite structure used as a tunable surface mode waveguide is designed. The tubes support tunable surface states. The tunable propagation capabilities of the structure are investigated by using the finite-difference time-domain. Simulation results show that the beam transmission distributions of the composite structure are sensitive to the frequency range of incident light and the surface morphology which can be modified by filling the tubes with different organic liquids. By adjusting the filler in tubes, the T-shaped, Y-shaped, and L-shaped propagations can be realized. The property can be applied to the tunable surface mode waveguide. Compared with a traditional single function photonic crystal waveguide, our designed structure not only has a small size, but also is a tunable device.     

New design of a beam-steering thermooptic multimode polymer waveguide switch

We present simulations of a Y-branch directional coupler activated using the thermooptic effect in a multimode polymer waveguide. Microheaters embedded beneath both sides of the waveguide at the Y-branch are used to generate an inhomogeneous temperature profile. Through the thermooptic effect, this temperature profile creates a refractive index profile in the channel waveguide material, which steers the beam to one of the two output branches. We determined the expected thermal profiles using finite element modeling (FEM). The transmission of a basic mode through the waveguide was then simulated using the beam propagation method (BPM). The results show that a high contrast ratio (>90%) can be achieved in response times on the order of 1 ms. Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.PACS 42.82.Et; 42.70.Jk; 42.79.Ta     

Analysis of optical coupling between air-holes photonic crystal and tapered dielectric waveguides

Two types of structures for the optical coupling between photonic crystal waveguide (PCW) with triangular air-holes lattice and tapered dielectric waveguide (TDW) are investigated. The TDWs are coupled with PCW at the input and output connections of the PCW, which can constitute a unidirectional waveguide structure. The transmission efficiencies of the input and output coupling are analyzed theoretically for different coupling structures. It is found that the coupling efficiencies vary with the width and length of coupling region. When the light transmitted from TDW to PCW, the highest transmission efficiency is 92.6%, and it is 99.6% when the light transmitted from PCW to TDW. Then the total transmission efficiency of the entire waveguide is simulated and it can reach 92.3% for one type of structure and is a little lower for the other type of structure under the chosen optimal structure parameters. Considering the current processing accuracy, the structure mentioned above should be an effective coupling manner that can be easily realized.     

Optical surface modes of photonic crystals for dual-polarization waveguide

In this study, the design of a polarization-independent (dual-polarization) waveguide is presented by utilizing surface modes of photonic crystals. The waveguide structure operates in a frequency interval that is commonly shared by both transverse-electric (TE) and transverse-magnetic (TM) polarizations. The numerical calculations based on plane wave expansion and finite-difference time-domain methods are carried out to design and demonstrate a surface mode waveguide that provides confinement and guiding for both TE and TM modes. Once the relevant modes are properly excited, the high transmission efficiency of the photonic crystal surface waveguide is ensured. The demand to have polarization-insensitive devices makes our proposed design an important component for the photonic integrated circuit applications. Finally, we also propose a broadband surface mode photonic crystal waveguide with a bandwidth value of 28% for only TE polarization.     

Optical switch effect of metal–dielectric–metal plasmonic waveguide coupled with stub structure

The transmission line theory (TLT) and the finite difference time domain (FDTD) method are applied to investigate the optical transmission characteristics of the metal–dielectric–metal (MDM) plasmonic waveguide coupled with a stub structure. The transmission rate of the FDTD simulation results demonstrates periodically variation from less than 1% to more than 92% as a function of the length of the stub, which fits well with the results of TLT. Furthermore, the transmission also performs a periodically switch distribution with the change of the refractive index of the stub from 1.0 to 2.0 gradually. Both methods are adopted for modulating the superposition phase of the interference between the reflected surface plasmon polaritons (SPPs) wave from the end of the stub and the passing SPPs wave in the waveguide, which can be interpreted as the principle mechanism for the optical switch effect of the MDM waveguide with a stub structure.     

Features of the dispersion characteristics of nonuniform plasma waveguides in a longitudinal magnetic field

We study the features of the dispersion curves and field structures of the fundamental axisymmetric mode of nonuniform layered plasma waveguides in a longitudinal magnetic field. It is shown that the presence of sharp boundaries between layers leads to the appearance of additional branches of the dispersion curves in the frequency range ω _Be < ω < ω_UH(0), where ω_Be is the electron gyrofrequency and ω_UH(0) is the upper-hybrid resonance frequency for the near-axis region of a nonuniform waveguide. The fields of eigenmodes corresponding to these branches comprise resonance structures near the sharp plasma-density variation at which the upper-hybrid resonance conditions are satisfied and plasma waves are excited. The frequency interval of such a branch is limited by the resonant frequencies of the neighboring uniform layers. It turns out that in the case of a strong magnetic field ({ie392-01}, where ω_p is the plasma frequency having the value {ie392-02} in the near-axis region of a nonuniform waveguide), the fundamental-mode field is localized in the near-axis region of a nonuniform waveguide, whereas in the opposite case {ie392-03}, the maximum wave fields are localized in either the upper-hybrid resonance region or the outer (near-boundary) layer of the waveguide if there is no resonance region. It is found that the whistler (helicon) contribution to the field structure of the fundamental axisymmetric mode is very small for narrow nonuniform waveguides (b < λ₀, where b is the waveguide radius and λ₀ is the wavelength in free space) if the plasma density on the axis is high compared with the cutoff density {ie392-04}. We present one of the possible explanations for the effect of narrowing of the plasma channel of a high-frequency whistler-range discharge with distance from a source in the increasing magnetic field. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Radiofizika, Vol. 51, No. 5, pp. 434–446, May 2008.     

Design and analysis of nano-deep corrugated waveguide grating-based dual-resonant filters in visible and infra-red regions

A theoretical analysis of nano-deep corrugated long-period waveguide gratings on a SU-8 polymer-based channel waveguide with NOA61 optical epoxy coated upper- and lower cladding is presented. The transmission spectra of the gratings show strong rejection bands both at visible (at wavelength region of 450?460 nm) and infra-red (at wavelength region of 1530?1540 nm) regions when a grating period of ?68 μm with optimized grating tooth height is considered. Phase-matching graphs are studied to find the relationship between resonance wavelength and grating period. These results show that the grating parameters significantly affect the characteristics of transmission spectra as well as the resonance wavelength of the grating. Long-period waveguide grating-based band pass filter made by use of same polymer materials are also designed and analyzed. These types of waveguide grating-based filters can widely be used for visible and infra-red wavelength sensing applications.     

一种高品质中空金属光波导

讨论了高品质中空金属光波导的工作原理及其制作工艺，制备了以金和银作为波导材料的中空波导管，并对空芯以及充入不同透明液体的液芯波导的透光特性进行了测试，结果表明：与中空介质波导相比，中空金属波导具有光传输损耗低，透过率对波导弯曲与失调不甚敏感等优点；而液芯金属波导的透光效率与透明材料的折射系数无关。文中描述了在特定波段内“中空光纤”的原理，并报道了Ｈｅ－Ｎｅ和ＣＯ２激光在中空金壁波导传输的实验结果。     

Waveguide circuits in three-dimensional photonic crystals

Waveguide circuits in three-dimensional photonic crystals with complete photonic band gaps are simulated with finite difference time domain (FDTD) simulations, and compared with measurements on microwave scale photonic crystals. The transmission through waveguide bends critically depends on the photonic crystal architecture in the bend region. We have found experimentally and theoretically, a new waveguide bend configuration consisting of overlapping rods in the bend region, that performs better than the simple waveguide bend of terminated rods, especially in the higher frequency portion of the band. Efficient beam splitters with this junction geometry are also simulated.     

Fast-response terahertz wave switch based on T-shaped photonic crystal waveguide

We design an ultra-fast terahertz wave switch based on T-shape photonic crystal waveguide. The polymer rod is added in the junction as a point defect, the refractive index of which can be varied by adjusting the external pump laser intensity. The transmission spectrum is calculated by finite-difference time-domain method, which shows that the output energy of the two output ports is closely related to the refractive index of the polymer rod. By continuous wave excitation of the guided mode, the simulation results show that the T-shaped photonic crystal waveguide can flexibly tune the power in two output ports. The tuning rate of the device is about 0.3 ns. These results provide a useful guide and a theoretical basis for the developments of terahertz wave functional components.     

Resonance and Antiresonance in Electronic Transport Process Through a T-Shaped Quantum Waveguide

By means of the transfer matrix approach, the linear conductance spectrum for electronic transport through a T-shaped quantum waveguide is calculated. The resonant peaks and the antiresonant dips in the conductance spectrum are mainly focused. The previous prediction about their positions by other theoretical approaches is checked. In addition, a function of spin filtering is suggested based on the interplay of the resonance and antiresonance in this T-shaped quantum waveguide.     

慢光在光子晶体弯折波导中的高透射传播

研究了慢光模式在SOI(silicon-on-insulator)材料光子晶体线缺陷弯折波导中的传输特性. 通过优化波导弯折处的结构参数,慢光模式在光子晶体60°与120°弯折波导中的透射率提高10倍以上,归一化透射率分别达到80%和60%以上. 为了进一步减慢光速,设计了新颖的高Q值耦合腔弯折波导结构,在归一化透射率达到75%的基础上,光波群速度低至c/170(c为真空光速). 研究结果对于增强光子晶体的慢光效应,提高光子晶体慢光器件的微型化和集成化都有一定的积 关键词： 光子晶体 慢光 弯折波导 透射率     

Unidirectional manipulation of surface plasmon polariton by dual-nanocavity in a T-shaped waveguide

A structure of two dimensional T-shaped metal-insulator-metal waveguide with dual-nanocavity is proposed. The two nanocavities located at each side of the slit on the lower metallic surface, act as band rejection filters and are capable of stopping the surface plasmon polaritons (SPPs) at the resonant wavelengths. The Fabry-Perot interferometry theory and the Finite-Difference-Time-Domain method are utilized to investigate the proposed waveguide. The numerical results demonstrate the realization of miniaturized photonic devices for effectively switching the SPPs propagation between the left and right waveguides in one direction.