一种紧凑的、可调的、基于缺陷共振的光开关

采用平面波展开法(PWM)和时域有限差分(FDTD)法,研究光在含点缺陷的光子晶体波导中的传输特性.计算结果表明,通过引入两共振腔(点缺陷),处于共振频率附近的光波将被完全反射回光子晶体波导.由于共振频率随点缺陷的折射率的变化而改变,这种现象可用来设计可调光开关. 关键词： 光子晶体波导 缺陷共振 光开关 透射率     

GaP波导型发射器产生频率可调谐太赫兹脉冲

报道了利用脉宽可调的光子晶体光纤飞秒激光放大器抽运矩形波导结构的GaP晶体太赫兹(THz) 发射器产生频率可调谐的超快THz脉冲.非线性晶体中光整流过程产生的THz辐射频率随抽运光脉冲宽度而 变化. GaP波导THz发射器可通过波导的几何尺寸来控制色散,以达到增加有效作用长度和提高输出功率的目的. 不同横截面尺寸的波导型发射器的THz辐射峰值频率随相位匹配条件的改变而改变,加以脉宽调节技术, 可以在大频谱范围获得频谱精细可调的THz脉冲.实验中在1 mm×0.7 mm的波导型THz发射器中获得了 频率可调谐的THz脉冲.提出实现THz辐射频率大范围调谐的GaP波导型阵列发射器的实施方案.     

喇叭型开口光子晶体波导的传输谱研究

设计一种喇叭型开口二维光子晶体波导,利用时域有限差分法计算波导传输谱图。模拟结果表明：通过改变开口处光子晶体椭圆点缺陷的结构,传输谱图中将出现相应变化的缺陷模,可用于实现频率可调的窄带光子晶体滤波器。     

Low group velocity in a photonic crystal coupled-cavity waveguide

A two-dimensional photonic crystal coupled-cavity waveguide is designed and optimized, the transmission spectrum is calculated by using the finite-difference time-domain method, and the group velocity of c/1856 is obtained. To our knowledge, this value of group velocity is the lowest group velocity in a photonic crystal waveguide calculated from its transmission spectrum so far. The result is confirmed by the photonic band structure calculated by using the plane wave expansion method, and it is found that the photonic crystal waveguide modes in a photonic band structure are in accordance with those in the transmission spectrum by using the finite-difference time-domain method. The mechanism of slow light in the coupled-cavity waveguide of photonic crystal is analysed.     

基于磁光子晶体的磁控可调谐太赫兹滤波器和开关

本文研究了铁氧体磁性材料应用于太赫兹波导器件的可行性. 利用铁氧体磁性材料的磁导率随外磁场改变而变化的性质,设计出了一种新颖的磁控连续可调谐太赫兹滤波器和开关. 利用平面波展开法(plane wave expansion,PWE)和时域有限差分法(finite difference time domain,FDTD)计算了二维磁光子晶体中外磁场变化对带隙位置和宽度的影响,结果显示应用该结构实现的滤波器和开关具有良好的性能. 关键词： 磁光子晶体 铁氧体 太赫兹     

基于光子晶体马赫-曾德尔干涉仪的太赫兹开关及强度调制器

通过对二维正方晶格光子晶体线缺陷模色散曲线慢光特性的研究, 利用外电场对液晶分子取向的调控作用, 在填充液晶的正方晶格波导的马赫-曾德尔干涉仪结构中实现了开关和强度调制等功能. 利用平面波展开法计算了光子晶体波导的线缺陷模, 分析了液晶折射率的变化对缺陷模的影响. 计算表明, 液晶折射率仅改变了0.1, 线缺陷模有效折射率改变达0.168, 该特性可以更为有效地实现对相位的控制, 进而实现高消光比开关和强度调制功能, 这种高效的相位调节器件在集成光系统中将有很好的应用前景.     

Proposal for a New Dense Wavelength Division Multiplexing Filter Based on Two-Dimensional Photonic Crystal Ring Resonator

Abstract

A new optical filter design based on a two-dimensional photonic crystal ring resonator structure with an N-channel model is proposed in this article. This study also shows that modifying the scatter radius and the waveguide width can significantly improve the performance of the original structure, which can solve the mode mismatch problem for output waveguide. Here, an example of a 16-channel photonic crystal ring resonator is provided; wavelength spacing of 1.6 nm and a high quality factor Q of 6,000 were achieved. The optical filter would be a potential key component in the application of dense wavelength division multiplexer devices.     

基于二维光子晶体点缺陷可调谐光功率分配器

在二维矩形阵列结构硅光子晶体中去除中间一排硅柱形成线波导,在线波导右侧引入点缺陷。利用时域有限差分法(FDTD)模拟仿真以及数值分析研究线波导中光耦合特性,计算出两个通道的分光比,发现改变光子晶体的温度可以明显改变这两个通道的光功率比。基于此结构,提出了一种新的光功率分配器,可以获得大范围的光功率比值,从1∶1～90∶1都可以通过改变光子晶体的温度来实现,并且当温度从0℃～200℃就可以实现这一功能,最后设计了一款三通道可调谐光功率分配器,通过调节两个点缺陷区域内温度来实现光功率的分配。     

二维光子晶体线缺陷结构的光谱辐射特性

光子晶体的禁带特性是该新兴材料的最根本特征。本文运用平面波展开法(PWE)计算了一种正方晶格Si光子晶体材料的禁带特性,并基于该材料设计出一种红外波段的线缺陷光子晶体波导结构。运用时域有限差分法(FDTD)研究了线缺陷二维光子晶体波导宽度对通频带、电场强度及透射能量的影响,研究结果为二维光子晶体波导器件的开发和利用提供了理论支撑。     

A photonic crystal side-coupled waveguide based on a high-quality-factor resonator array

Based on the present coupled mode theory of the photonic crystal resonator array in this paper,we propose a novel side-coupled waveguide to achieve highly efficient coupling of photonic crystal devices.It is found that the coupling efficiency is sensitive to the interval,the total number and the quality factor of the resonator.Considering the coupling efficiency and the coupling region,we select five resonators with an interval of six lattice periods.By optimizing the structure parameters of the waveguide and resonator,the quality factors of the resonator can be modulated and the coupling efficiency of the side-coupled waveguide reaches 95.47% in theory.Compared with other coupling methods,the side-coupled waveguide can realize efficient coupling with a compact structure,a high level of integration and a low degree of operational difficulties.     

A photonic crystal side-coupled waveguide based on a high-quality-factor resonator array

Based on the present coupled mode theory of the photonic crystal resonator array in this paper, we propose a novel side-coupled waveguide to achieve highly efficient coupling of photonic crystal devices. It is found that the coupling efficiency is sensitive to the interval, the total number and the quality factor of the resonator. Considering the coupling efficiency and the coupling region, we select five resonators with an interval of six lattice periods. By optimizing the structure parameters of the waveguide and resonator, the quality factors of the resonator can be modulated and the coupling efficiency of the side-coupled waveguide reaches 95.47% in theory. Compared with other coupling methods, the side-coupled waveguide can realize efficient coupling with a compact structure, a high level of integration and a low degree of operational difficulties.     

聚焦离子束研制半导体材料光子晶体

介绍了利用聚焦离子束设备在多种半导体材料上成功研制的近红外波段二维光子晶体，给出了相关微加工结果，发现微加工的尺寸和理论设计尺寸相吻合；测试了所加工的无源光子晶体光子带隙和有源光子晶体的发光谱. 实验证明聚焦离子束可以研制二维光子晶体及相关光子晶体器件. 关键词： 聚焦离子束 半导体材料 光子晶体     

二维点缺陷正方光子晶体的微腔结构

通过平面波展开法对由Al₂O₃介质棒在空气背景介质中构成含有点缺陷的二维正方光子晶体微腔结构进行研究,计算得出缺陷态能带以及缺陷态模场分布。缺陷模对应的电磁波波长为470~476nm。对该微腔结构的品质因数的求解,得出缺陷态光谱曲线。在光谱曲线中,随着传输波长的增大,将产生几个峰值,并且在475nm处的波动最为明显,反映出在475nm附近的电磁波段在缺陷处的光强较大。进一步利用全矢量等效折射率法研究该结构缺陷模频率的稳定性,得出等效折射率的变化曲线。从等效折射率变化曲线可以看出,当传输波长达到475nm时,该结构已经达到稳定传输的区域。含缺陷模的二维光子晶体微腔结构在光子晶体发光二极管以及高阈值半导体激光器等方面有着重要的应用价值。     

利用耦合波导列提高光子晶体波导辐射

将耦合波导列应用于光子晶体单模波导,提出一种提高光辐射的光子晶体结构. 基于时域有限差分方法的理论研究表明,当将耦合波导列附加到单模光子晶体波导出口端的适当位置,使出射光分成若干强弱不一的光束,这些光束在传播空间通过干涉形成一定程度的汇聚,大大提高了光子晶体波导在水平方向的光辐射效率. 另外,当耦合波导列的行数大于某固定值(2N=8)时,辐射质量基本保持不变,由此可获得最紧凑的器件结构. 这种类型光子晶体在近场光学和集成光学等诸多方面有潜在的应用价值. 关键词： 光子晶体波导 光辐射 波导列 耦合波导     

Low power Electro-optical filter: Constructed using silicon nanobeam resonator and PIN junction

In this paper, a high tunable Electro-optical filter is designed and simulated with low electric power consumption. A silicon nanobeam resonator based on one-dimensional photonic crystal in the form of Fabry–Perot structure, silicon-on-insulator waveguide, is proposed with a PIN junction. In designing nanobeam resonator, “deterministic design method” is used to achieve the high quality factor and high-transmission rate. Tuning of the resonant wavelength in the output channel of the filter is achieved by manipulating the refractive index of the active area by using the free-carrier dispersion effect. The output wavelengths of designed device can be tuned for the telecom-friendly 1.55 µm range. The device shows a wavelength shift higher than 3 nm for a power consumption of only 0.9 mW. Finally, the simulation results show that the provided device can be considered as a narrowband and tunable Electro-optical filter that is suitable for DWDM communication system.     

Electromagnetic modes in semi-infinite photonic crystals

In a real photonic crystal, there exist three modes: propagation mode, evanescence mode and surface mode. Using ideal modal, semi-infinite photonic crystals, we study their effects on the transmission spectrum of photonic crystals, respectively. Because there exists only one air–crystal interface in a semi-infinite photonic crystal, no multiple reflection occurs and no evanescent modes and backward-propagating modes exist in this structure. The effects of the evanescence modes are studied by comparing the transmission spectrum of a finite-thickness photonic crystal slab and that of a semi-infinite photonic crystal. In addition, the effects of the backward-propagating modes are investigated using a coated semi-infinite photonic crystal structure. Finally, we study the effects of the surface modes, and find that the transmission spectrum of a semi-infinite photonic crystal is strongly dependent on its termination.     

Optical surface modes of photonic crystals for dual-polarization waveguide

In this study, the design of a polarization-independent (dual-polarization) waveguide is presented by utilizing surface modes of photonic crystals. The waveguide structure operates in a frequency interval that is commonly shared by both transverse-electric (TE) and transverse-magnetic (TM) polarizations. The numerical calculations based on plane wave expansion and finite-difference time-domain methods are carried out to design and demonstrate a surface mode waveguide that provides confinement and guiding for both TE and TM modes. Once the relevant modes are properly excited, the high transmission efficiency of the photonic crystal surface waveguide is ensured. The demand to have polarization-insensitive devices makes our proposed design an important component for the photonic integrated circuit applications. Finally, we also propose a broadband surface mode photonic crystal waveguide with a bandwidth value of 28% for only TE polarization.     

光子晶体波导耦合的波分复用研究

两平行光子晶体单模波导的相互耦合组成一个耦合结构。两本征模的色散曲线相交并出现简并,简并模之间的耦合作用使模式的分布发生了改变。由于耦合的作用,各个波长的光波会在不同的波导中传输。在简并点处两本征模发生解耦合,光波会沿着原来的方向传输。将两个不同耦合长度的光子晶体波导耦合结构集成在一起,就可以组成一个三波长的光子晶体波分复用器。     

光控二维光子晶体光开关

提出了一种调节液晶光子晶体光子带隙的方法。二维三角介质柱形光子晶体位于2块熔凝石英片之间,在介质柱之间填充各向同性排列的液晶,受偏振紫外光照射后,光诱导液晶分子定向排列,通过光诱导液晶分子取向改变液晶的折射率。数值模拟结果表明：通过外界光场控制所填充的向列相液晶分子的方向可以对这种二维三角形介质柱光子晶体的禁带结构进行调节。该可调光子晶体可控制波导中TM模和TE模的选择性传输,因而可应用于制作全光光开关。     

The study of electro-optical sensor based on slotted photonic crystal waveguide

A compact and sensitive electro-optical sensor based on slotted photonic crystal waveguide (S-PhCW) is demonstrated. The electro-optical sensor can be realized in photonic crystal (PhC) slabs of silicon in Silicon-on-Insulator (SOI). Nonlinear optical polymer is used as infiltration. By applying three-dimensional finite difference time domain (3D-FDTD), the sensitivity and quality factor of electro-optical sensor with different slotted waveguide width are calculated. In addition, sensitivity and the optical properties such as transmission spectrum and field distributions are compared between electro-optical sensor based on line defect photonic crystal waveguide (W1-PhCW) and that based on slotted photonic crystal waveguide (S-PhCW). Simulation results demonstrate that, compared with electro-optical sensor based on line defect photonic crystal waveguide, the sensitivity and quality factor is improved by 30 times and 6.6 times respectively in sensor based on slotted photonic crystal waveguide. Besides, the proposed PhC sensor devices have the advantage of a compact structure with the potential for monolithic integration with optical-to-electrical on-chip conversion and detection.