两亲性超支化聚合物的研究进展

两亲性超支化聚合物作为一种新型功能性材料.近年来引起了人们的广泛关注.两亲性超支化聚合物的合成丰要是利用不同亲水性的链段对超支化聚合物端基进行改性,或者首先在超支化聚合物末端产生活性位点,再利用超支化分f作为大分子引发剂引发烯类单体进行斤环聚合、原子转移自由基聚合等得到以超支化聚合物为核的两亲性超支化共聚物;这些分子由...     

含氟丙烯酸酯共聚物表面性能的稳定化研究

为提高传统含氟丙烯酸酯乳胶膜表面性能的稳定性,以γ-(甲基丙烯酰氧基)丙基三甲氧基硅烷(MPS)作为可交联单体,采用细乳液聚合法合成了MPS改性的含氟丙烯酸酯共聚物,利用DLS、TEM、IR对聚合物进行表征,研究了MPS对合成乳液的稳定性、涂膜性能和膜表面接触角稳定性的影响。结果表明,细乳液聚合法适合用于对水敏感单体的聚合,合成的纯丙烯酸酯乳胶为球形结构,平均粒径为92 nm,而氟丙乳胶和含3%MPS的含硅氟丙乳胶形成了典型的核壳结构,平均粒径分别增大至107 nm和103 nm,含硅氟丙聚合物中存在Si-O-Si的交联结构。涂膜性能测试表明,MPS的引入增加了共聚物膜的硬度、耐溶剂性和耐水性。接触角测试表明,随MPS用量的增加,乳胶膜对水的初始接触角和动态接触角随时间的降低值均呈先增大后减小的趋势,共聚体系中加入适量MPS,通过含氟链段与MPS链段的协同作用,可显著提高涂膜表面性能的稳定性。     

超支化聚(酯-胺)分子结构及固化涂层性能研究

近年来,颜德岳等基于A2型单体二丙烯酸酯及BB2′型单体二胺化合物合成了多种端胺基超支化聚(酯-胺),并对反应机理及聚合物结构进行了系统研究[1,2],结果表明,由于B与B′活性差异,反应首先生成AB2′型和B4′型中间体,进一步聚合得到可溶性产物.我们基于A3型单体三丙烯酸酯与B2型单体二胺化合物合成了端丙烯酸酯基超支化聚(酯-胺)[3,4].在这些体系中,由于官能团反应活性高,难以控制反应程度.另外,由于超支化聚合物不能直接用作结构材料,其在涂料、粘合剂等领域的应用多基于末端官能团的固化反应[5].但通常由于官能团在分子表面密集分布,部…     

核壳乳液聚合法制备含氟硅丙烯酸酯乳液

以氟醇RfCH2CH2OH和乙烯基硅氧烷VTES为原料合成的氟硅单体,与甲基丙烯酸甲酯、丙烯酸丁酯在复合乳化体系中通过核壳乳液聚合制备了稳定的氟硅共聚乳液。对氟硅单体和氟硅丙烯酸酯共聚物的结构用红外光谱进行了表征,结果表明,得到了目标单体和共聚物。共聚物的TEM形态观察发现,乳胶粒子具有明显的核壳结构,平均粒径在125 nm左右。与丙烯酸酯共聚物相比,氟硅丙烯酸酯共聚物乳胶膜的吸水率降低至8.32%,热分解温度提高了23℃,耐溶剂性与氟硅单体的含量关系不大。     

可紫外光固化的超支化聚硅氧烷合成及固化研究

同线型聚硅氧烷聚合物相比，超支化聚硅氧烷聚合物具有低粘度、高反应活性和良好的相容性等特点，其中以制备超支化的聚硅氧烷基硅氧烷和聚烷氧基硅氧烷为主．对于超支化聚硅氧烷主要是以ABx（X=2～6）（其中A为双键，B为硅氢键）型单体为原料，在氯铂酸或Pt／C的催化下，通过硅氢加成反应一步制备，最终聚合物的端基（B）为硅氢键，而双键则完全反应，此外也可通过含不同数目烷氧基硅烷的水解缩合制备超支化聚硅氧烷．     

氧负离子聚合在超支化聚合物合成中的应用

近年来,氧负离子聚合得到较快发展,单体种类已经由酯基的β位上含有供电性杂原子的甲基丙烯酸酯类扩展到环氧类、甲基丙烯酸羟酯类单体.氧负离子引发这两类单体聚合,可以得到新型结构的超支化聚合物.对氧负离子引发合成超支化聚合物的机理及其应用进行了综述.     

“活”的α-甲基苯乙烯共聚物:聚合反应新化学和材料工程新技术

高于临界聚合反应温度时,α-甲基苯乙烯(AMS)单体和其聚合物处于聚合-解聚平衡.基于AMS聚合物在受热时可裂解生成大分子链自由基的特性,提出了含AMS结构单元的共聚物是一种"活"的,可作为大分子自由基引发剂的概念,并通过实验对AMS共聚物的引发性能和应用进行了研究.首先,合成了AMS与(甲基)丙烯酸酯类单体、丙烯酸、苯乙烯和马来酸酐等的共聚物.然后以上述共聚物为大分子引发剂,在90℃引发(甲基)丙烯酸酯类单体和苯乙烯等的本体聚合、溶液聚合和乳液聚合,得到了嵌段共聚物.用ESR谱证明了AMS的共聚物在加热时能裂解生成以碳原子为中心的大分子链自由基.此外,在聚合物的熔融共混中,AMS分解产生的大分子链自由基通过偶合反应形成接枝链,原位生成相容剂.AMS共聚物还可以对碳纳米管及无机粒子进行表面原位接枝改性.AMS共聚物是一类无小分子残留的绿色自由基引发剂,可以用于低成本制备两嵌段共聚物,也可以用于聚合物的熔融共混增容.     

聚乙二醇型超支化聚酯胺的制备及表征

以M_n=250的聚乙二醇二丙烯酸酯为A_2单体(含有两个A基因的单体,其余类推),N-乙基乙二胺为B'B_2单体,利用丙烯酸酯基和胺基的迈克尔加成聚合反应,一锅法合成了表面含丙烯酸酯键、骨架含聚乙二醇(PEG)、内部含叔胺的具有三维椭球状结构的超支化聚酯胺,并研究了其聚合动力学。利用咪唑对超支化聚酯胺进行改性,并初步研究了咪唑改性的超支化聚酯胺的pH响应性和水溶性。利用核磁共振氢谱、红外光谱、凝胶渗透色谱、GPC-MALLS多角度激光散射系统表征了超支化聚酯胺的分子结构和化学组成。结果表明:聚乙二醇链段的引入能够赋予超支化聚酯胺水溶性;咪唑的引入有利于提高超支化聚酯胺的pH响应性。     

室温交联型硅丙微胶乳的合成研究Ⅲ.聚合工艺对聚合稳定性及胶膜性能的影响

采用两种聚合工艺(种子微乳液聚合法和单体预乳化法)分别合成了室温交联型有机硅改性丙烯酸酯聚合物微胶乳，研完了不同工艺条件对聚合稳定性、乳胶粒径和胶膜的结构性能的影响．     

两亲性全季铵盐超支化聚合物的设计与合成及主-客体超分子着色应用研究

采用高效的巯基-炔点击化学与Menschutkin季铵化反应,合成了一种带有1个叠氮基、2个炔基和2个季铵盐基团的AB2型季铵盐单体,通过核磁共振、红外光谱、质谱等方法对单体结构进行了确认.将所得单体进行点击聚合,得到全季铵盐超支化聚合物,并用端叠氮基的长链烷烃封端,得到核亲水-壳憎水的两亲性超支化聚季铵盐.研究所得两亲性超支化聚合物对染料的装载性能,结果表明所合成的带正电荷两亲性聚合物对多种带负电荷的水性染料装载效果好,平均相转移率高达95%.进一步将装载染料的主-客体超分子复合物用于聚合物制品着色,发现其对SBS及PMMA等聚合物有很好的着色效果,着色均匀且不掉色,着色的膜色泽鲜艳透明.     

Synthesis of water-soluble hyperbranched polymer and its application in acrylic latex

A water-soluble hyperbranched polymer (WHBP), obtained from a second generation of hyperbranched polyester and maleic anhydride, was studied. Its effects on the properties of acrylic latexes, which were based on emulsion polymerization of butyl acrylate (BA), methyl methacrylate (MMA), acrylic acid (AA) and WHBP, and latex film were discussed. The characteristics of WHBP were determined by nuclear magnetic resonance spectroscopy (NMR), Fourier transform infrared (FTIR) and gel permeation chromatography (GPC). Particle size and morphology of latex particles were confirmed by dynamic light scattering (DLS) and transmission electron microscope (TEM). The investigation showed that WHBP could be used in emulsion polymerization, and that latex of poly(BA-MMA-WHBP) was more stable than that of poly(BA-MMA-AA). The hardness of latex film increased from 2B to HB when WHBP was used.     

INVERSE EMULSION POLYMERIZATION OF ACRYLAMIDE: POLYMERIZATION KINETICS AND PROCESS DEVELOPMENT

Inverse emulsion polymerization confers the benefits of emulsion polymerization kinetics — rapid polymerization rates combined with high polymer molecular weights — on water-soluble polymers, particularly polyacrylamide and its copolymers and derivatives, and allows easy dissolution of the polymer in water by inversion of the latex. The mechanism and kinetics of the inverse emulsion polymerization of acrylamide in o-xylene containing Tetronic 1102 emulslfier and benzoyl peroxide initiator are described, particularly the formation of 10-200nm multiple emulsion droplets resulting from the particulate emulsifier, and their effect on the polymerization process     

Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using ⁶⁰Co γ-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.     

有机硅改性丙烯酸酯共聚乳液合成方法及胶膜性能的研究

用一次投料法、单体乳液滴加法和引发剂滴加法有机硅改性丙烯酸酯共聚乳液，聚合过程、胶粒形态及乳液稳定性的观测结果表明：单体乳液滴加法是合成该类乳液的最佳方法，研究了单体乳液滴加法中有机硅含量与聚合反及胶膜性能的关系，结果表明：有机硅含量在１５％以下时，聚合反应可以顺利进行，胶膜性能不仅依赖于聚合时有机硅单体的总量，而且还依赖于有机硅单体中活性硅氧烷所占的比例。     

镶嵌型乳胶粒子的合成

以苯乙烯、甲基丙烯酸甲酯、丙烯腈等单体或它们的混合物为硬单体,天然胶乳为弹性组分,经多步种子乳液聚合法制得了在天然胶乳的粒子上镶嵌硬聚合物相的互穿网络型乳胶粒子.考察了十二烷基硫酸钠、十二烷基苯磺酸钠、壬基酚聚氧乙烯醚、油酸等乳化体系,过硫酸钾、过氧化苯甲酰热引发体系及异丙苯过氧化氢-四乙烯五胺、叔丁基过氧化氢-四乙烯五胺等氧化还原引发体系对聚合反应的影响.研究了交联剂用量对互穿结合率、溶胶含量的影响及溶胀时间、硬单体组成、乳化剂种类对乳胶粒子形态的影响,确定了适宜的聚合配方和工艺条件.透射电镜观察乳粒形态结果表明,单一使用极性或非极性单体,仅得到核-壳结构乳液,而采用不同极性单体复合、溶胀、互穿,得到的是镶嵌硬聚合物型乳粒结构.     

Synthesis of polyacrylate core-shell structure latex by radiation techniques

A series of poly(butyl acrylate-co-methyl methacrylate)/poly (ethyl acrylate-co-acrylic acid) interpenetrating polymer network (IPN) was synthesized in latex form by emulsion polymerization. The multiphase morphology of the latex particles was studied after two-stage polymerization by using transimission electron microscope (TEM), the result indicated that the morphology of the particles comprises gradient shell structure, cellular structure and core-shell structure. The change of morphology might stem from emulsion polymerization by radiation initiation or chemical initiation and the weight composition of poly(EA-co-MMA) seed latex which formed the core. By radiation techniques, we successfully synthesized poly( BA-co-MMA)/poly(EA-co-AA) latex of core-shell structure having (42-8)/(46-4) weight compositions. The PA core-shell structure latex applied to textile as a water proofing coating showed higher water-pressure and easier handling than that with PA homogeneous phase structure latex.     

Structure and properties of novel fluorinated polyacrylate latex prepared with reactive surfactant

The novel fluorinated polyacrylate latex was successfully prepared by emulsion polymerization of perfluorononylene allyl ether, butyl acrylate and methyl methacrylate initiated by potassium persulfate in water and emulsified with the reactive surfactant. Films of the novel fluorinated polyacrylate latex were prepared by coating the latex directly on the clean glass sheet and allowed to dry at 80°C in the bake oven. The characteristics of the film such as hydrophobicity and glass transition temperature were studied; its structure was investigated by FTIR spectrometry and NMR. The influence of the fluorinated monomer content on the emulsion polymerization and performance of the latex were also studied. It was shown that the hydrophobicity and glass transition temperature of the latex are improved when the fluorinated monomer is introduced to copolymerize with other monomers, however, the stability of emulsion polymer and the conversion rate is decreased with the increase of its content.     

荧光探针法研究核壳结构有机硅-丙烯酸酯乳液的聚合行为

以芘为荧光探针,探讨了有机硅-丙烯酸酯核壳乳液聚合过程中,芘的第一振动峰(373 nm处)与第三振动峰(384 nm处)荧光强度的比值I1/I3与乳化剂、有机硅单体(D4)和引发剂(KPS)用量之间的关系,并结合聚合过程中探针芘的I1/I3峰值与单体转化率及乳胶粒形态演变之间的关系,研究了核壳结构有机硅-丙烯酸酯乳液的聚合行为.研究结果表明,探针芘的I1/I3峰值随乳化剂用量,D4用量,KPS用量不同发生相应的变化,随单体转化率的增加而增大.当乳化剂用量、D4用量、KPS与总单体的质量比依次为2 g、8 g、0.7%时,得到的乳液具有优良的综合性能.聚合反应过程中,当种子乳胶粒转变为核壳乳胶粒时,芘的I1/I3峰值仍呈现出明显的转变,说明有机硅-丙烯酸酯核壳乳液具有互穿聚合物网络结构.因此,荧光探针可用于研究有机硅-丙烯酸酯核壳乳液聚合反应进程.     

反相乳液共聚合制备两性丙烯酰胺共聚物的研究

采用Span80-Tween80复合乳化剂和AIBA引发剂,进行丙烯酸钠(NaAA)/丙烯酰胺(AM)/丙烯酰氧基乙基三甲基氯化铵(DAC)反相乳液共聚合.研究了聚合温度、引发剂用量、单体浓度、共聚单体中DAC和AM含量、乳化剂用量及其HLB值、水/油比和水相pH值等聚合反应工艺条件或参数对聚合反应单体转化率和聚合物特性粘度的影响,聚合物特性粘度随引发剂用量和单体浓度的增大而增大的实验结果证实了该两性丙烯酰胺共聚物反相乳液制备过程中凝胶效应的存在.傅立叶红外光谱组成分析表明了两性丙烯酰胺共聚物的成功合成,扫描电镜观测乳胶粒粒径范围在0.6~8.0μm.     

团聚纳米SiO_2在苯乙烯乳液聚合过程中的再分散过程及机理

用二氧化硅 (SiO2 )存在下的乳液聚合法制备了聚苯乙烯 (PSt) 纳米SiO2 复合材料 ,研究了苯乙烯(St)乳液聚合过程中团聚纳米SiO2 的解离与再分散过程及分散的机理 .发现商品纳米SiO2 粒子以团聚体形式存在 ,团聚体大小远超出纳米级范围 .随聚合时间的延长 ,St的转化率逐渐增加 ,而PSt SiO2 复合微胶囊的粒径逐渐减小 ,反应 12 0min后 ,转化率和复合微胶囊粒子的粒径趋于稳定 .透射电镜 (TEM)也显示PSt SiO2 复合微胶囊粒子具有海岛结构 ,而SiO2 粒子的粒径在纳米范围内 ,表明在乳液聚合过程中SiO2 团聚体被逐渐解离 ,并重新分散到纳米尺度 .红外光谱研究发现 ,在乳液聚合过程中 ,除生成PSt均聚物外 ,还在纳米SiO2 表面生成了PSt接枝共聚物 ,改善了无机纳米粒子与聚合物之间的界面相容性 .聚合过程中的反应热和剪切搅拌是团聚体被解离和重新分散的主要原因 ,而生成的聚合物起到隔离作用