反式-/顺式-1,4-聚异戊二烯共混体系的结晶动力学

采用差示扫描量热(DSC)法对反式-/顺式-1,4-聚异戊二烯共混体系的等温及非等温结晶动力学进行了研究,分别采用Avrami方程和莫志深法对其动力学参数进行了解析.研究结果表明,在反式-/顺式-1,4-聚异戊二烯共混体系的等温及非等温结晶过程中,顺式-1,4-聚异戊二烯(CPI)组分的存在会降低反式-1,4-聚异戊二烯(TPI)组分的结晶速率;在等温结晶过程中,CPI组分会提高TPI组分自身的结晶度;而非等温结晶过程中,CPI则提高了共混物中β晶型的相对含量.     

水性聚氨酯/功能化石墨烯纳米复合材料的非等温结晶动力学

采用差示扫描量热法DSC研究了水性聚氨酯/功能化石墨烯(WPU/FGNs)纳米复合材料的非等温结晶行为,分别采用Ozawa方程、莫志深方程研究复合材料的非等温结晶动力学,并通过Kissinger方程计算了结晶过程中的活化能。 结果表明,石墨烯在复合材料的结晶过程中起到异相成核剂的作用,提高了复合材料的结晶起始温度、峰值温度和结晶速率;增加石墨烯的质量分数,复合材料的结晶维数增加;石墨烯增加至0.3%,复合材料的活化能从-47.74 kJ/mol降低至-53.60 kJ/mol,继续增加石墨烯至1.0%,复合材料的活化能增加至-41.74 kJ/mol。     

不同分子量聚L-乳酸的非等温结晶动力学研究

采用DSC方法研究了不同分子量聚乳酸在不同降温速率下的结晶过程,利用Ozawa方程和Kissinger方程研究了其非等温结晶动力学。结果表明,随着降温速率的增大和分子量增加,结晶峰向低温偏移,且峰形趋于平缓。求得分子量为2.6×104的聚乳酸的Ozawa指数m接近3,以异相成核的三维球晶生长为主,而分子量为14.3×104和19.2×104的聚乳酸的Ozawa指数m接近4,以均相成核的三维球晶生长为主,结晶活化能分别为-165.8kJ/mol、-82.1kJ/mol和-75.4kJ/mol。建立的"铰链"模型解释了不同分子量聚乳酸结晶活化能的显著差异,得到了聚乳酸分子量与结晶活化能的关系。     

PA13N的合成和非等温结晶动力学研究

采用DSC方法研究了PA13N在不同降温速率下的结晶过程,并利用Avrami方程研究了其非等温结晶动力学。在非等温结晶过程中,随着降温速率的增大,结晶温度向低温偏移。综合利用Avrami方程得到Avrami指数为1.35~1.88和结晶速率常数Zc≈1;并求得其结晶活化能为-58.42kJ/mol。结果表明,PA13N的结晶能力小于其他脂肪族尼龙。     

聚2-吡咯烷酮的非等温结晶动力学

用差示量热扫描热分析仪(DSC)测试了不同降温速率下聚2-吡咯烷酮(PPD)样品的温度-热焓曲线,样品黏均分子量为2.2×10~4,熔点为272℃。采用Jeziorny法、Ozawa法和莫志深法分析了PPD的非等温结晶动力学。结果表明,在给定降温速率范围内,Ozawa法不适用于描述PPD的非等温结晶动力学过程,Jeziorny法只适用于描述PPD的主结晶阶段,而莫志深法能很好地描述整个结晶过程。Jeziorny法处理结果表明,PPD主结晶阶段的Avrami指数(n)为1.68~1.78,晶体生长为准二维生长。莫志深法处理结果表明,在单位结晶时间里达到某一相对结晶度所需的降温速率随相对结晶度的增加而增大。用Kissinger方程求得PPD的非等温结晶活化能为-31.9kJ/mol。     

电子辐照对聚反式1,4-丁二烯晶型转变的影响

由于晶体结构对高分子性能有较大影响,因此研究其晶体结构具有重要意义．目前,已发现聚反式１,４－丁二烯（ＰＴＢＤ）存在两种晶型结构［１］,分别为单斜相和六方相,在低温下主要为单斜相,高温下主要为六方相．在一定温度下,单斜相和六方相可发生可逆的相转变［２］．本文以透射电镜为主要手段,在电子射线辐照下,研究单斜相向六方相的转变过程,不仅摄得样品的单斜相和六方相电子衍射谱,而且还拍摄到两相共存的电子衍射谱．１　ＰＴＢＤ的晶型转变Ｆｉｇ．１　ＤＳＣｔｈｅｒｍａｌｇｒａｍｏｆＰＴＢＤＳｃａｎｒａｔｅ：１０℃…     

苯乙烯-丙烯等规立构嵌段共聚物(iPS-b-iPP)的非等温结晶动力学的研究

用DSC法研究了苯乙烯-丙烯等规立构嵌段共聚物的非等温结晶动力学。结果表明:冷却速率在5～20℃/min范围内,共聚物的非等温结晶动力学参数能很好地符合Avrami动力学方程,非等温结晶速率常数与冷却速率有关,动力学结晶能力则同时受到冷却速率和共聚物组成比的影响。文中还讨论了在非等温结晶条件下共聚物的结晶成核和生长方式与共聚物组成和结构的关系。联合Avrami方程和Ozawa方程推导的非等温结晶动力学方程较好地描述了iPS-b-iPP嵌段共聚物的非等温结晶动力学过程。     

聚乙交酯非等温结晶行为研究

利用差示量热扫描热分析仪(DSC)测得了不同降温速率下聚乙交酯(PGA)的非等温结晶的温度-热焓曲线。分别通过Ozawa法、Jeziorny法和莫志深法对PGA的非等温结晶机理进行了分析。Ozawa法结果表明:在给定的温度范围内,Ozawa法并不适用于描述PGA的非等温结晶行为;Jeziorny法结果表明:不同降温速率下,PGA结晶过程的Avrami指数(n)接近4,PGA非等温结晶为均相成核、晶粒三维增长的过程;莫志深法结果表明:Avrami指数与Ozawa指数的比值(a)基本无变化,动力学参数f(T)随降温速率增加逐渐增大,即在更快的降温速率下,PGA结晶更充分,可获得更高的结晶度。通过Kissinger方程计算得到的PGA结晶扩散活化能为-66.9kJ/mol。     

低密度聚乙烯/乙丙烯三元共聚(LDPE/EPO)共混体系的结晶动力学

用DSC方法研究了LDPE/EPO共混体系的等温及非等温结晶动力学,对LDPE/EPO共混体系的等温结晶动力学研究表明,共混物是三维生长的异相成核,共混物在各个结晶温度下的结晶过程都是以方式K_g(Ⅱ)进行的.采用联系Avrami方程和Ozawa方程导出的新非等温结晶动力学方程,处理了LDPE/EPO共混体系,得到了非等温结晶过程的一些基本参数,新方程很好地描述了此共混体系的非等温结晶动力学过程.     

杜仲胶与合成反式-1,4-聚异戊二烯等温结晶行为的对比研究

首先通过红外光谱(IR)、核磁共振(1 H-NMR)和凝胶渗透色谱(GPC)对所选用的杜仲胶(EUG)和合成反式-1,4-聚异戊二烯(TPI)进行了微观结构分析,进而采用差示扫描量热法(DSC)和偏光显微镜(POM)对EUG和TPI的等温结晶行为进行了对比研究,重点讨论了二者链化学组成和微观结构的不同对二者等温结晶行为的影响。Avrami方程分析DSC数据结果及POM观察结果显示,EUG和TPI的成核方式和生长机理各不相同。EUG主要为均相成核,而TPI则为异相成核。EUG的等温结晶行为对温度有着更高的敏感性。EUG的结晶活化能(147.2kJ/mol)大于TPI的(114.8kJ/mol)。在37℃下熔体等温结晶,EUG所得主要为β球晶,而TPI为α和β两种球晶并存,且TPI中引发剂残渣等灰分的异相成核作用导致很早就发生了球晶间的相互碰撞。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.