表面改性对VGCF分散性质的影响

针对气相生长碳纤维极易团聚及与树脂基体界面结合能力较差的难题,采用双氧水-浓硝酸二步法对VGCF进行表面改性处理。利用X射线衍射仪、热重分析仪、傅立叶红外光谱仪、紫外可见分光光度计等测试分析了改性前后VGCF的表面结构和在溶剂中的分散性,并以形状记忆聚氨酯为基体,采用溶液混合法制备了气相生长碳纤维/形状记忆聚氨酯的复合材料,测试了复合材料的力学性能。经过改性后,VGCF的石墨晶型结构几乎没有改变,VGCF表面的含氧官能团浓度得到较大提高,且其在有机溶剂中的分散性及分散稳定性也得到很大提高;在气相生长碳纤维/形状记忆聚氨酯的复合材料截面中,扫描电镜观察表明表面改性使得VGCF在基体中的分散性及与基体的界面结合能力都得到一定程度的提高;经二步法改性处理后的气相生长碳纤维比未处理气相生长碳纤维对复合材料的力学性能的增强效果更为明显。     

氨基硅油改性碳纤维/环氧树脂复合材料的耐老化性能

通过在复合树脂基体中引入氨基硅油进行改性,制备了不同氨基硅油含量的碳纤维/环氧树脂复合材料,在湿热环境下进行老化实验后,通过动态热机械分析(DMA)、热重分析(TGA)、拉伸性能测试、扫描电镜(SEM)及接触角测定等方法研究氨基硅油对于碳纤维/环氧树脂复合材料热力学性能、力学强度保持率和耐水性能的改善效果。实验结果表明,经老化实验后含氨基硅油材料的抗拉强度保持率最高提升了13.23%。当氨基硅油含量为8 wt%时,复合材料表面接触角均值大于90~o。氨基硅油对环氧树脂基体的改性可改善碳纤维/环氧树脂复合材料的耐湿热老化性能。     

聚离子液体修饰碳纳米管及其对环氧树脂力学性能的影响

为改善多壁碳纳米管(MWCNTs)在环氧树脂(EP)中的分散性和界面性质,以1-乙烯基-3-丁基咪唑六氟磷酸盐([VBIM]PF6)为单体合成聚离子液体(PIL),用于MWCNTs的表面改性.用热重分析(TG),拉曼光谱(Raman)和扫描电镜(SEM)对改性碳纳米管(PIL-CNTs)进行了表征.结果表明,PIL可吸附在MWCNTs表面且不改变MWCNTs的电子结构.与原始MWCNTs相比,PIL-CNTs在丙酮中的分散性更好.在EP中加入0.5 wt%的PIL-CNTs,以4,4'-二氨基二苯甲烷(DDM)为固化剂制备环氧树脂固化物.动态力学(DMA)研究表明,PIL-CNTs提高了EP的储能模量,玻璃化温度比纯EP和MWCNTs/EP分别提高了5.6℃和3.3℃;PILCNTs/EP的拉伸强度,弯曲强度和冲击强度较纯EP分别提高了35.2%,26.4%和45.0%.拉伸断面的SEM可看出PIL-CNTs在复合材料中的分散性和与环氧树脂基体的界面结合力均优于原始MWCNTs.     

甲基磺酸对PBO纤维的表面改性

采用甲基磺酸(MSA)溶液对PBO纤维表面进行化学改性,用单丝拔出试验测定了改性前后PBO纤维与环氧树脂基体的界面剪切强度,并通过扫描电镜(SEM)、X-射线光电子能谱(XPS)、接触角分别对处理前后纤维的表面形貌、表面组成以及表面自由能进行了表征.研究结果表明:在甲基磺酸质量分数为60%的溶液中,60℃下处理6 h的PBO纤维与环氧树脂基体的界面剪切强度比未处理的提高了81%,并且纤维表面O元素的质量分数增加了13.3%,表面自由能增加了17.3%.当溶液中甲基磺酸的质量分数、处理时间和处理温度进一步提高时,PBO纤维的皮层将遭受破坏,导致界面剪切强度下降.     

多聚磷酸/乙酸体系对PBO纤维表面改性的研究

采用多聚磷酸/乙酸体系并结合偶联剂处理方法对PBO纤维表面进行化学改性,采用扫描电镜和液滴形状法对处理前后纤维表面形态结构和纤维表面亲水性进行了表征,通过单丝拔出试验测定了改性前后PBO纤维与环氧树脂基体的界面剪切强度。利用X光电子能谱和热重分析等方法对纤维表面元素组成和热稳定性进行了分析。研究发现,多聚磷酸/乙酸体系偶联剂的方法改性后PBO纤维表面亲水性明显增强,与水的接触角从大于90°下降到42.8,°PBO纤维/环氧树脂的界面剪切强度较未处理样品提高了45%。     

多巴胺表面改性碳纤维对PVDF/CF复合材料性能的影响

对碳纤维(CF)进行去浆处理,再利用多巴胺对CF改性,得到多巴胺改性CF(DARCF),添加马来酸酐接枝聚偏氟乙烯(PVDF-g-MAH),制备了DARCF增强PVDF-g-MAH复合材料(PVDF-g-MAH/DARCF)。采用原子力显微镜(AFM)、X射线光电子能谱(XPS)和傅里叶变换红外光谱(FT-IR)对CF表面的粗糙度、结构和官能团进行表征。采用扫描电镜(SEM)、界面接触角测试和力学性能测试对复合材料的界面、力学性能进行测试。结果表明:改性之后,DARCF表面粗糙度增加,与树脂的界面结合强度提高,PVDF-g-MAH/DARCF的弯曲强度和模量比未改性的PVDF/CF分别提高了71.3%和36.9%。     

固相力化学方法回收利用废弃聚丙烯/废旧电路板的研究

采用固相力化学技术制备废旧电路板非金属材料(WPCB)改性粉体,填充废弃聚丙烯(PP),制备了高性能废旧PP/WPCB复合材料,研究了固相剪切对WPCB粒度、粒度分布以及PP/WPCB复合材料结构、流变性能和力学性能的影响。结果表明,磨盘碾磨使WPCB粉体体积粒径由282.4μm降到63.5μm,比表面积由0.06m2/g提高到0.14m2/g,粒度分布明显变窄,玻纤与环氧树脂剥离效果明显。固相力化学方法制备WPCB粉体填充废旧PP后,其分散大幅改善,加工性能明显优于未碾磨体系,复合材料力学性能优于纯PP和未经固相力化学处理的PP/WPCB复合材料,相对于纯PP拉伸强度提高14.6%,弯曲模量提高82.5%,缺口冲击强度提高11.2%。得到的材料表面色泽均一、成本低廉,具有良好工业化前景。     

聚合物在碳纤维表面的电沉积

用电沉积方法将苯乙烯-马来酸酐、乙酸乙烯酯-马来酸酐、甲基丙烯酸甲酯-马来酸酐共聚物沉积于碳纤维表面。通过实验初步证实了此过程的负离子-自由基机理,以及沉积层在纤维表面的物理粘附。由于电沉积的聚合物中间层改善了碳纤维增强塑料中纤维-基体树脂间的界面粘接作用,使原来的剪切破坏基本上发生于界面的情况转变成发生于基体本身为主。并将单向碳纤维增强环氧树脂复合材料的层间剪切强度,由原来的600kg/cm~2左右提高到1000kg/cm~2以上,经沸水浸泡100小时后的强度损失也减少了。     

超临界正丁醇对回收碳纤维复合材料的降解及表征

采用响应面分析方法设计超临界正丁醇降解废弃的碳纤维/环氧树脂(CF/EP)复合材料降解实验,用以回收碳纤维.通过Design-Expert V8.0建立环氧树脂降解率和工艺参数之间的数学模型,获得了最优工艺参数;通过图形优化研究了工艺参数对环氧树脂基体降解率的影响规律;通过场发射电子扫描显微镜、原子力显微镜、X射线光电子能谱仪、显微共焦激光拉曼光谱仪及单丝拉伸等分析最优工艺参数下回收的碳纤维的表面形貌、表面化学、石墨化程度及力学性能.结果表明,建立的数学模型拟合误差范围为±5.5%,实现了回收工艺参数的预估;单因素对环氧树脂基体降解率的影响程度为:反应温度保温时间添加剂浓度正丁醇含量;最优工艺参数为:反应温度330℃,保温时间60 min,添加剂浓度0.0538 mol/L,投料比0.024g/mL.回收的碳纤维表面无残留树脂,没有发生明显的石墨化,且表面平均粗糙度与原碳纤维相近;与原始碳纤维相比,回收的碳纤维的拉伸强度约为原碳纤维的93.58%,杨氏模量约为原碳纤维的94.87%.     

外力辅助分散作用下环氧树脂粘土纳米复合材料中粘土的微观结构与解离机理研究

采用不同分散方法(机械搅拌、高速均质搅拌和球磨分散)制备环氧树脂粘土纳米复合材料,研究了分散方法对不同有机粘土解离结构和纳米复合材料力学性能的影响,并在此基础上探讨了粘土的解离机理.结果表明,普通机械搅拌只能使小粒径粘土或大粒径粘土团聚体的外部片层解离;施加一定的外力(如高速均质搅拌)促进粘土团聚体分散,有利于粘土片层的解离;利用剪切摩擦作用较强的球磨法分散粘土,不同处理剂改性粘土的内外片层都可以充分解离,而有机改性剂中酸性质子的催化作用对粘土片层解离的影响不大,只要粒径足够小,片层解离的驱动力(基体弹性力、反应性等)能够克服其所受阻力(片层引力、层外基体粘性阻力、层内粘性引力等),粘土内外各片层将会同时向外迁移而解离.纳米复合材料的力学性能大大改善,冲击强度和弯曲强度分别提高近50%和8%;     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.