The effect of nanolayer AlF<Subscript>3</Subscript> coating on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> cycle life in high temperature for lithium secondary batteries

The surface of the spinel LiMn₂O₄ was coated with AlF₃ by a chemical process to improve its electrochemical performance at high temperatures. The morphology and structure of the original and AlF₃-coated LiMn₂O₄ samples were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM). All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns. It was found that the surfaces of the original LiMn₂O₄ samples were covered with a nanolayer AlF₃ after the treatment. The charge/discharge of the materials were carried at 220 mA/g in the range of 3.0 and 4.4 V at 55°C. While the original LiMn₂O₄ showed 17.8% capacity loss in 50 cycles at 55°C, the AlF₃-coated LiMn₂O₄ (118.1 mA h/g) showed only 3.4% loss of the initial capacity (122.3 mA h/g) at 55°C. It is obvious that the improvement in cycling performance of the coated-LiMn₂O₄ electrode at 55°C is attributed to the presence of AlF₃ on the surface of LiMn₂O₄. Published in Russian in Elektrokhimiya, 2009, Vol. 45, No. 7, pp. 817–819. The article is published in the original     

Low Temperature Synthesis of Nano-Sized Lithium Manganese Oxide Powder by the Sol-Gel Process Using PVA

Lithium manganese oxide (LiMn₂O₄) powder with spinel structure has been synthesized by a sol-gel method using an aqueous solution of metal nitrates containing polyvinyl alcohol (PVA). The role of PVA and the calcination conditions for the formation of LiMn₂O₄ have been studied. Homogeneity and reactivity of the precursor powder are enhanced with an increase in the amount of PVA in the starting solution. When the amount of PVA is low, an impurity phase-Mn₂O₃ is formed at low temperature. On the other hand, when the vinyl alcohol monomer unit of PVA to metal ion ratio is 2 : 1 in the starting solution, only spinel phase is formed at 180°C and organic-free LiMn₂O₄ powder is obtained at as low as 400°C. Nanosized LiMn₂O₄ particles with a narrow size distribution have been successfully prepared by this technique. This method with proper amount of PVA results in much lower calcination temperature and shorter calcination time for producing the single spinel phase in comparison with the conventional solid state reaction and other solution techniques.     

Synthesis and characterization of submicron size particles of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> by microemulsion route

Among the various positive electrode materials investigated for Li-ion batteries, spinel LiMn₂O₄ is one of the most important materials. Small particles of the active materials facilitate high-rate capability due to large surface to mass ratio and small diffusion path length. The present work involves the synthesis of submicron size particles of LiMn₂O₄ in a quaternary microemulsion medium. The precursor obtained from the reaction is heated at different temperatures in the range from 400 to 900 °C. The samples heated at 800 and 900 °C are found to possess pure spinel phase with particle size <200 nm, as evidenced from XRD, SEM, and TEM studies. The electrochemical characterization studies provide discharge capacity values of about 100 mAh g⁻¹ at C/5 rate, and there is a moderate decrease in capacity by increasing the rate of charge–discharge cycling. Studies also include charge–discharge cycling and ac impedance studies in temperature range from −10 to 40 °C. Impedance data are analyzed with the help of an equivalent circuit and a nonlinear least squares fitting program. From temperature dependence of charge-transfer resistance, a value of 0.62 eV is obtained for the activation energy of Mn³⁺/Mn⁴⁺ redox process, which accompanies the intercalation/deintercalation of the Li⁺ ion in LiMn₂O₄.     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

Physical properties and electrochemical performance of LiMn2O4 cathode materials prepared by a precipitation method

LiMn₂O₄ powder for lithium-ion batteries was prepared by a precipitation method, and the effects of calcination temperature on the physical properties and electrochemical performance of the samples were investigated by various methods. The results of X-ray diffraction (XRD) showed that the lattice parameter (a) and the unit cell volume (v) decrease with the increasing calcination temperature, and the LiMn₂O₄ sample calcined at 750°C has smaller particle size and higher crystallinity than other samples. The results of the electrochemical experiments showed that the sample calcined at 750°C has larger peak currents, higher initial capacity, and better cycling capability, because of its lower charge-transfer resistance and larger diffusion coefficient of Li⁺ ions than those of other samples.     

PVP-Assisted ZrO2 coating on LiMn2O4 spinel cathode nanoparticles prepared by MnO2 nanowire templates

LiMn₂O₄ spinel nanorods prepared from nanowire MnO₂ templates were capped with polyvinyl pyrrolidone (PVP) and coated with ZrC₂O₄ precursors in aqueous solution. Upon annealing at 600 °C in air, an amorphous ZrO₂ nanoscale coating layer was obtained on the spinel nanoparticles with a particle size of <100 nm that formed from the splitting of the original spinel nanorods. The electrochemical cycling results clearly showed that nanoscale ZrO₂ coating significantly improved the rate capability and cycle life at 65 °C in spite of very high surface area of the spinel nanoparticles.     

尖晶石型LiMn2-xInxO4(x=0，0.01，0.02，0.05)的合成及电化学性能研究

以醋酸锰、氢氧化锂和三氧化二铟为原料,以柠檬酸为配位剂,采用溶胶-凝胶法制备了掺杂In的尖晶石LiMn2-xInxO4(x=0,0.01,0.02,0.05),采用XRD、SEM对目标材料进行了结构和形貌表征,采用恒流充放电、循环伏安(CV)以及交流阻抗(EIS)谱测试对材料进行了电化学性能表征,考察了不同In掺杂量对材料性能的影响。结果表明,当In掺杂量为1%时,LiMn1.99In0.01O4样品具有纯的尖晶石锰酸锂结构,在0.5C和3.4～4.35 V电压范围条件下,LiMn1.99In0.01O4的初始放电容量为119.9 mAh.g-1,经过1C 30次,2C 30次,再0.5C 5次循环后,其放电容量保持率为84.9%,显示了良好的电化学性能。掺杂1%的In的样品比未掺杂的样品具有更优的高温循环稳定性能。     

LiMn2O4 nanorods as a super-fast cathode material for aqueous rechargeable lithium batteries

LiMn₂O₄ nanorods were prepared by a facile hydrothermal method in combination with traditional solid-state reactions and characterized by X-ray diffraction analysis. Their electrochemical behavior was tested by cyclic voltammetry and repeated charge/discharge cycling. Results show that the reversible intercalation/deintercalation of Li-ions into/from LiMn₂O₄ cathode can yield up to 110 mAh/g at 4.5 C, and still retains 88% at the very large charge rate of 90 C with well-defined charge and discharge plateaus. It presents very high power density, up to 14.5 kW/kg, and very excellent cycling behavior, 94% capacity retention after 1200 cycles. It is thus a competitor for LiFePO₄.     

石墨烯/尖晶石LiMn2O4纳米复合材料制备及电化学性能

采用溶胶凝胶法和还原氧化石墨法制备尖晶石LiMn2O4纳米晶和石墨烯纳米片,并采用冷冻干燥法制备了石墨烯/尖晶石LiMn2O4纳米复合材料,利用XRD、SEM、AFM等对其结构及表面形貌进行表征;利用CV、充放电、EIS研究纳米复合材料的电化学性能和电极过程动力学特征。结果表明:纳米LiMn2O4电极材料及其石墨烯掺杂纳米复合材料的放电比容量分别为107.16 mAh.g-1,124.30 mAh.g-1,循环100周后,对应容量保持率为74.31%和96.66%,石墨烯可显著改善尖晶石LiMn2O4电极材料的电化学性能,归结于其良好的导电性。纳米复合材料EIS上感抗的产生与半导体尖晶石LiMn2O4不均匀地分布在石墨烯膜表面所造成局域浓差有关,并提出了感抗产生的模型。     

LiCoO2对LiMn2O4改性过程的研究

在LiCoO2、LiMn2O4、LiNiO2这三种锂离子电池正极材料中,尖晶石LiMn2O4由于具有价廉、对环境友好、使用安全的显著优点,被普遍认为是最有希望的新型正极材料。但该材料在高温下较快的容量衰减制约了其规模应用[1~3]。为改善LiMn2O4的高温性能,各国学者普遍采用掺杂法,即在制备L     

A novel method to fabricate lithium-ion polymer batteries based on LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/NG electrodes

A novel method to fabricate lithium-ion polymer batteries (LiPBs) has been developed. The LiPBs was fabricated without microporous polyolefin separators, taking spinel lithium manganese oxide (LiMn₂O₄) and natural graphite (NG) as the electrodes. The thicknesses of the cathodes and the anodes are 190 and 110 μm, respectively. The NG anode was coated with a microporous composite polymer film (20 μm thick) which composed of polymer and ultrafine particles. The coating process was effective and simple to be used in practical application, and ensured the composite polymer film to act as a good separator in the LiPB. The LiPBs assembled with the coated NG anodes and pristine LiMn₂O₄ cathodes presented better electrochemical performances than liquid lithium-ion battery counterparts, proving that the microporous composite polymer film can improve the performance of the coated NG anode. In this paper, the spinel LiMn₂O₄/(coated)NG-based LiPBs exhibited high rate capability, compliant temperature reliability, and significantly, excellent cycling performance under the elevated temperature (55°C).     

锂离子电池正极材料LiMn2O4的低热固相合成与性能表征

锂离子电池具有比能量高、环境污染小等优点,广泛应用于手提电话、便携式电脑、摄像机等设备中。其正极材料的研究是锂离子电池的研究重点。层状结构的LiCoO2、LiNiO2和尖晶石结构的LiMn2O4是仅有的三种能在3.5V以上电位可嵌入Li的正极材料[1~3]。目前市售的锂离子电池主要采用LiCoO2作正极材料,但由于Co资源缺乏和价格相对昂贵,而锰资源丰富,价格低廉且无毒,对环境友好,因此世界各国都在大力进行以LiMn2O4为正极材料的锂离子电池的实用化研究。LiMn2O4传统的制备方法是高温固相反应合成法[4~7],但由于Mn的变价多,与Li形成贫Li或…     

Ge4+、Sn4+掺杂尖晶石LiMn2O4的合成与电化学表征

使用Ge⁴⁺、Sn⁴⁺作为掺杂离子, 通过高温固相法制备四价阳离子掺杂改性的尖晶石LiMn₂O₄材料. X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明, Ge⁴⁺离子取代尖晶石中Mn⁴⁺离子形成了LiMn_2-xGe_xO₄ (x=0.02,0.04, 0.06)固溶体; 而Sn⁴⁺离子则以SnO₂的形式存在于尖晶石LiMn₂O₄的颗粒表面. Ge⁴⁺离子掺入到尖晶石LiMn₂O₄材料中, 抑制了锂离子在尖晶石中的有序化排列, 提高了尖晶石LiMn₂O₄的结构稳定性; 而在尖晶石颗粒表面的SnO₂可以减少电解液中酸的含量, 抑制酸对LiMn₂O₄活性材料的侵蚀. 恒电流充放电测试表明, 两种离子改性后材料的容量保持率均有较大幅度的提升, 有利于促进尖晶石型LiMn₂O₄锂离子电池正极材料的商业化生产.     

Synthesis and electrochemical properties of spinel LiMn2O4 prepared by the rheological phase method

Pure-phase and well-crystallized spinel LiMn₂O₄ powders were successfully synthesized by a simple rheological phase method. The thermal behavior and structure properties of the powders prepared by the rheological phase method compared with the solid-state reaction were investigated by thermogravimetry, powder X-ray diffraction , scanning electron microscopy and transmission electron microscopy. According to the results of the electrochemical tests, it is obvious that the sample resulting from the rheological phase method shows higher discharge capacity and better cycling stability than one formed in the solid-state reaction. The cyclic voltammogram and columbic efficiency curves also confirm that the product by the rheological phase method has a good cycling performance due to its fine cubic spinel structure and morphology.     

Effects of Metal Ion Sources on Synthesis and Electrochemical Performance of Spinel LiMn2O4 Using Tartaric Acid Gel Process

The effect of lithium and manganese ions on the synthesis, phase purity, and electrochemical properties of tartaric acid gel processed lithium manganese oxide spinel were investigated. The poor bonding between both lithium and manganese ions with tartaric acid was shown by the FT-IR analysis when lithium nitrate and/or manganese nitrate were used as sources. Li₂MnO₃ and Mn₂O₃ impurities formed in addition to lithium manganese oxides when nitrate salts were used as the sources. When acetate salts were used as sources for the lithium and manganese ions, single-phase LiMn₂O₄ was obtained. These results indicate that homogeneous bonding between acetate salt and tartaric acid was formed. The capacity of single-phase LiMn₂O₄ calcined at 500°C was 117 mAh/g which was much higher than those containing Mn₂O₃ and Li₂MnO₃ impurity compounds. Thus, sources of lithium and manganese ions play an important role in the synthesis and electrochemical behaviors of lithium manganese oxide spinel.     

Synthesis and electrochemical characteristics of oxysulfide spinel material for lithium secondary batteries

Oxysulfide spinel LiMn₂O_3.98S_0.02 powders with monodispersed, and highly homogeneous particles were synthesized by a sol-gel method using an aqueous solution of metal acetates and sulfide containing glycolic acid as a chelating agent. The oxysulfide spinel, LiMn₂O_3.98S_0.02 electrode initially delivers 80 mAh g⁻¹, steadily increases during cycling, and reaches 99 mAh g⁻¹ at the 20th cycle. The substitution of a small amount S for O in LiMn₂O₄ spinel helps to maintain structural integrity during cycling, which then overcomes the Jahn–Teller distortion in the spinel Mn phase in the 3 V region.     

KCl熔盐法制备LiMn2O4

采用熔盐法合成了LiMn₂O₄。熔盐的使用可以使原来固相反应的高温焙烧时间缩短。合成获得的材料结晶良好，颗粒大小在数百个纳米左右，有较明显的团聚现象。该材料的初始容量为113 mAh·g^-1，循环性能优良，前100次的容量平均衰减率在0.05%左右；倍率性能亦非常优秀，8 C放电时的容量为1 C放电容量的93%以上。熔盐的用量在4倍于Li⁺以上时，对材料的结构形貌和性能都没有明显影响。     

Preparation of compact Al2O3 film on metal for oxidation resistance by polyvinylpyrrolidone

Oxidation resistance of metal at high temperature can be improved by an environmentally friendly solution deposition approach. Stable precursor solution with high oxide concentration, favorable viscosity and low surface tension was prepared using aluminum sec-butoxide (ASB) and polyvinylpyrrolidone (PVP) as starting raw materials. Alumina sol-gel films were deposited onto metal by spin-coating followed by heat treatment. When PVP was added according to an amount of 50 mg/mL into a sol with an ASB/H₂O molar ratio of 1:35, the as-obtained sol exhibited favorable gelation time and viscosity. The surface tension of the alumina sol with PVP was examined to be lower by 32% than the sol (ASB:H₂O = 1:100) without PVP. TG-DTA analyses show the densification of the alumina gel film with PVP was progressed within a wide temperature range from 200 to 650 °C. Crack-free Al₂O₃ film with a thickness up to 1.5 μm was successfully produced on metallic substrate by three spin-coating cycles. SEM and XRD analyses revealed the gel film transformed into compact α-Al₂O₃ material after calcined at 1,000 °C for 0.5 h. The weight gained by the samples during firing at 1,000 °C indicated that the Al₂O₃ coating film could reduce the rate of oxidation by ∼81%. The hardness of the Al₂O₃ film coated metal was higher by 260% than the uncoated metal that was calcined at 1,000 °C for 0.5 h. It was confirmed by adhesion test that both the alumina/PVP hybrid film and the as-produced α-Al₂O₃ coating film had strong adhesion.     

ZrO2- and Li2ZrO3-stabilized spinel and layered electrodes for lithium batteries

Strategies for countering the solubility of LiMn₂O₄ (spinel) electrodes at 50 °C and for suppressing the reactivity of layered LiMO₂ (M=Co, Ni, Mn, Li) electrodes at high potentials are discussed. Surface treatment of LiMn₂O₄ with colloidal zirconia (ZrO₂) dramatically improves the cycling stability of the spinel electrode at 50 °C in Li/LiMn₂O₄ cells. ZrO₂-coated LiMn_0.5Ni_0.5O₂ electrodes provide a superior capacity and cycling stability to uncoated electrodes when charged to a high potential (4.6 V vs Li⁰). The use of Li₂ZrO₃, which is structurally more compatible with spinel and layered electrodes than ZrO₂ and which can act as a Li⁺-ion conductor, has been evaluated in composite 0.03Li₂ZrO₃ · 0.97LiMn_0.5Ni_0.5O₂ electrodes; glassy Li_xZrO_2 + x/2 (0<x⩽2) products can be produced from colloidal ZrO₂ for surface coatings.     

Preparation of spherical spinel LiMn2O4 cathode material for lithium ion batteries

A novel process is proposed for synthesis of spinel LiMn₂O₄ with spherical particles from the inexpensive materials MnSO₄, NH₄HCO₃, and NH₃H₂O. The successful preparation started with carefully controlled crystallization of MnCO₃, leading to particles of spherical shape and high tap density. Thermal decomposition of MnCO₃ was investigated by both DTA and TG analysis and XRD analysis of products. A precursor of product, spherical Mn₂O₃, was then obtained by heating MnCO₃. A mixture of Mn₂O₃ and Li₂CO₃ was then sintered to produce LiMn₂O₄ with retention of spherical particle shape. It was found that if lithium was in stoichiometric excess of 5% in the calcination of spinel LiMn₂O₄, the product had the largest initial specific capacity. In this way spherical particles of spinel LiMn₂O₄ were of excellent fluidity and dispersivity, and had a tap density as high as 1.9 g cm^–3 and an initial discharge capacity reaching 125 mAh g^–1. When surface-doped with cobalt in a 0.01 Co/Mn mole ratio, although the initial discharge capacity decreased to 118 mAh g^–1, the 100th cycle capacity retention reached 92.4% at 25°C. Even at 55°C the initial discharge capacity reached 113 mAh g^–1 and the 50th cycle capacity retention was in excess of 83.8%.