Electron transfer studies on cholesterol LB films assembled on thiophenol and 2-naphthalenethiol self-assembled monolayers

We have formed the cholesterol monolayer and multilayer LB films on the self-assembled monolayers of 2-naphthalenethiol (2-NT) and thiophenol (TP) and studied the electrochemical barrier properties of these composite films using cyclic voltammetry and electrochemical impedance spectroscopy. We have also characterized the cholesterol monolayer film using grazing angle FTIR, scanning tunneling microscopy (STM) and atomic force microscopy (AFM). Cholesterol has a long hydrophobic steroid chain, which makes it a suitable candidate to assemble on the hydrophobic surfaces. We find that the highly hydrophobic surface formed by the self-assembled monolayers (SAM) of 2-NT and TP act as effective platforms for the fabrication of cholesterol monolayer and multilayer films. The STM studies show that the cholesterol monolayer films on 2-NT form striped patterns with a separation of 1.0 nm between them. The area per cholesterol molecule is observed to be 0.64 nm2 with a tilt angle of about 28.96 degrees from the surface normal. The electrochemical studies show a large increase in charge transfer resistance and lowering of interfacial capacitance due to the formation of the LB film of cholesterol. We have compared the behavior of this system with that of cholesterol monolayer and multilayers formed on the self-assembled monolayer of thiophenol.     

Langmuir-Blodgett-Kuhn and self-assembled films of asymmetrically substituted poly(paraphenylene)

Asymmetrically substituted poly(paraphenylene) (PhPPP) with hydrophilic and hydrophobic side chains was investigated. The polymer behavior at the air-water interface was studied on the basis of surface pressure-area (pi-A) isotherms and compression/expansion hysteresis measurements. PhPPP can form stable monolayers with an area per repeat unit of A=0.20+/-0.02 nm2 and a collapse pressure in the range of pi=25 mN/m. Then, Langmuir-Blodgett-Kuhn (LBK) films of PhPPP were prepared by horizontally and vertically transferring the Langmuir monolayers onto hydrophilic solid substrates at pi=12 mN/m. Cross-section analysis of the AFM tapping-mode topography images of a single transferred monolayer reveals a thickness of d0=0.9+/-0.1 nm. Taking into account the obtained monolayer thickness, curve-fitting calculations of angular scan data of LB monolayers measured using surface plasmon resonance (SPR) spectroscopy lead to a value for the refractive index of n=1.78+/-0.02 at lambda=632.8 nm. Next, the spontaneous formation of a PhPPP monolayer by adsorption from solution was studied ex situ by atomic force microscopy and UV-vis spectroscopy and in situ by using SPR spectroscopy. Stable self-assembled monolayers of PhPPP can be formed on hydrophilic surfaces with a thickness similar to that of the monolayer obtained using the LB method. The characterization results confirmed the amphiphilic character and the self-assembly properties of PhPPP, as well as the possibility of preparing homogeneous monolayer and multilayer films.     

Sensitivity enhancement of SPR biosensor with silver mirror reaction on the Ag/Au film

Based on well-known silver mirror reaction the Ag film was formed on Au film modified by self-assembled monolayer (SAM) of 1,6-hexanedithiol (HDT). The sensitivity of the biosensor based on this Ag/Au film is enhanced compared to that based on Au film. When the surface plasmon resonance (SPR) biosensor based on this Ag/Au film was used to determine human IgG, the range of concentrations of human IgG that could be determined is 0.30-40.00 μg mL⁻¹. The lowest concentration (0.30 μg mL⁻¹) that could be detected was about 8 times lower than that obtained by the biosensor without modification by Ag film (2.50 μg mL⁻¹), which demonstrated that the biosensor based on Ag/Au film could make the resonant wavelength move to longer wavelength following with the sensitivity enhancement of the SPR biosensor.     

湿化学镀SPR金基底及其性能表征

建立一种由单一水相操作的表面等离子体共振法(SPR)制备金基底.即:在3-氨基丙基三甲氧基硅烷(APTMS)修饰的玻璃片上自组装一层细小的金胶纳米粒子,以此为催化模板,利用化学镀技术在纳米尺度范围内控制金膜的均匀增长,获得优异SPR信号响应所需要的金膜形貌和厚度.紫外光谱(UV-vis),透射电镜(TEM)观测表明,纳米金膜催化模板粒径约为2.5 nm.扫描电镜(SEM)观察湿化学镀SPR金基底均匀分布,粒径约为40 nm.与商品化真空镀金基底相比,湿化学镀金基底对乙醇的SPR响应强度相当,且可调控性更高.     

Novel determination of cadmium ions using an enzyme self-assembled monolayer with surface plasmon resonance

The activity of the enzyme urease is known to be inhibited by the heavy metal cadmium. The binding of cadmium to urease and the consequent changes of the enzyme structure are the basis of the surface plasmon resonance (SPR) biosensing system reported herein. To facilitate the formation of a self-assembled monolayer (SAM) of the urease on gold-coated glass SPR sensor disks, the enzyme has been modified with N-succinimidyl 3-(2-pyridyldithiol) propionate (SPDP). The urease monolayer was exposed to trace levels of cadmium ions and monitored by SPR. From circular dichroism (CD) data, it is believed that the conformation of the active nickel site of the urease changes upon binding of the cadmium ions. It is this change of the enzyme monolayer, measured by SPR, which has been related to the cadmium ion concentration in the range of 0–10 mg l⁻¹. These data are the first report of a SPR biosensor capable of detecting metal ions.     

Gold nanoparticles chemisorbed by a terphenyldithiol self-assembled monolayer for fabrication of a protein biosensor

In this study, improved detection of bovine serum albumin (BSA) was achieved by use of a fabricated surface plasmon resonance (SPR) biosensor. Terphenyldithiol (TPDT) was self-assembled on a gold substrate, then gold nanoparticles (Au-NPs) were chemisorbed on to the TPDT monolayer by strong bonding with the terminal thiol groups of the TPDT. The new sensor obtained was tested for immobilization of protein. The SPR results revealed much better detection of BSA by Au-NPs chemisorbed on the TPDT self-assembled monolayer (SAM) than by the bare SAM on the gold substrate.     

Hybridization of oligonucleotide by using DNA self-assembled monolayer

The interaction between DNA immobilized on surface and oligonucleotides at the interface is important in detection and diagnostic processes. However, it is difficult to immobilize DNA with maintaining its activity and to realize an efficient hybridization in previous methods. Here, to establish a novel DNA-functionalized surface, the DNA self-assembled monolayer (SAM) was constructed on a gold substrate using thiolated DNA composed of double-stranded (ds) and single-stranded (ss) portion. The DNA SAM was characterized by surface plasmon resonance (SPR), XPS. The hybridization of ss portion of DNA was attempted using the SAM, and in situ monitored by SPR. XPS measurement indicated that the thiolated DNA could form a stable monolayer on a gold substrate through sulfur–gold interaction. SPR measurement implied that the long axis of the DNA standing on the substrate. These results indicated formation of the DNA SAM on the substrate. Hybridization of target DNA containing a complementary sequence for the probe portion was observed by SPR. Moreover, one mismatch of oligonucleotide could be distinguished using the DNA SAM. The SPR result indicates that hybridization of target DNA and probe DNA on the DNA SAM occurs on the DNA SAM.     

Enhanced Photocurrent Generation in Self-Assembled Monolayers Formed at Plasmonic Gold Nanostructures

The effect of localized surface plasmon resonance (SPR) appearing at the surfaces of gold nanoparticles (AuPs) was successfully applied for the enhancement of photocurrents from porphyrin ( Po ) immobilized on AuPs. The electrode consisting of AuPs with different sizes (∼15 or ∼35 nm) was prepared using the AuP film formed at the liquid/liquid interface, and then Po was self-assembled on the gold surface. The SPR effect for the AuP film was verified from the attenuated total reflection SPR and absorption measurements. Photocurrents from the modified electrodes were compared with the corresponding planar electrode. Appreciable enhancement of photocurrents was observed.     

Interactions of doxorubicin with self-assembled monolayer-modified electrodes: electrochemical, surface plasmon resonance (SPR), and gravimetric studies

We present the results on the partitioning of doxorubicin (DOX), a potent anticancer drug, through the model membrane system, self-assembled monolayers (SAMs) on gold electrodes. The monolayers were formed from alkanethiols of comparable length with different ω-terminal groups facing the aqueous electrolyte: the hydrophobic -CH(3) groups for the case of dodecanethiol SAMs or hydrophilic -OH groups of mercaptoundecanol SAMs. The electrochemical experiments combined with the surface plasmon resonance (SPR) and gravimetric studies show that doxorubicin is likely adsorbed onto the surface of hydrophilic monolayer, while for the case of the hydrophobic one the drug mostly penetrates the monolayer moiety. The adsorption of the drug hinders further penetration of doxorubicin into the monolayer moiety.     

Enzyme-encapsulated silica monolayers for rapid functionalization of a gold surface

We report a simple and rapid method for the deposition of amorphous silica onto a gold surface. The method is based on the ability of lysozyme to mediate the formation of silica nanoparticles. A monolayer of lysozyme is deposited via non-specific binding to gold. The lysozyme then mediates the self-assembled formation of a silica monolayer. The silica formation described herein occurs on a surface plasmon resonance (SPR) gold surface and is characterized by SPR spectroscopy. The silica layer significantly increases the surface area compared to the gold substrate and is directly compatible with a detection system. The maximum surface concentration of lysozyme was found to be a monolayer of 2.6 ng/mm(2) which allowed the deposition of a silica layer of a further 2 ng/mm(2). For additional surface functionalization, the silica was also demonstrated to be a suitable matrix for immobilization of biomolecules. The encapsulation of organophosphate hydrolase (OPH) was demonstrated as a model system. The silica forms at ambient conditions in a reaction that allows the encapsulation of enzymes directly during silica formation. OPH was successfully encapsulated within the silica particles and a detection limit for the substrate, paraoxon, using the surface-encapsulated enzyme was found to be 20 microM.     

Surface characterization and efficiency of a matrix-free and flat carboxylated gold sensor chip for surface plasmon resonance (SPR)

We report the preparation and characterization of a matrix-free carboxylated surface plasmon resonance (SPR) sensor chip with high sensing efficiency by functionalizing a bare gold thin film with a self-assembled monolayer of 16-mercaptohexadecanoic acid (SAM–MHDA chip). The self assembled monolayer surface coverage of the gold layer was carefully evaluated and the SAM was characterized by infrared reflection absorption spectroscopy, X-ray photoemission spectroscopy, atomic force microscopy, X-ray reflectivity-diffraction, and SPR experiments with bovine serum albumin. We compared the SPR signal obtained on this chip made of a dense monolayer of carboxylic acid groups with commercially available carboxylated sensor chips built on the same gold substrate, a matrix-free C1 chip, and a CM5 chip with a ~100 nm dextran hydrogel matrix (GE Healthcare). Two well-studied interaction types were tested, the binding of a biotinylated antibody (immunoglobulin G) to streptavidin and an antigen–antibody interaction. For both interactions, the well characterized densely functionalized SAM–MHDA chip gave a high signal-to-noise ratio and showed a gain in the availability of immobilized ligands for their partners injected in buffer flow. It thus compared favourably with commercially available sensor chips.     

Electrochemically controlled assembly and logic gates operations of gold nanoparticle arrays

The reversible assembly of β-cyclodextrin-functionalized gold NPs (β-CD Au NPs) is studied on mixed self-assembled monolayer (SAM), formed by coadsorption of redox-active ferrocenylalkylthiols and n-alkanethiols on gold surfaces. The surface coverage and spatial distribution of the β-CD Au NPs monolayer on the gold substrate are tuned by the self-assembled monolayer composition. The binding and release of β-CD Au NPs to and from the SAMs modified surface are followed by surface plasmon resonance (SPR) spectroscopy. The redox state of the tethered ferrocene in binary SAMs controls the formation of the supramolecular interaction between ferrocene moieties and β-CD-capped Au NPs. As a result, the potential-induced uptake and release of β-CD Au NPs to and from the surface is accomplished. The competitive binding of β-CD Au NPs with guest molecules in solution shifted the equilibrium of the complexation-decomplexation process involving the supramolecular interaction with the Fc-functionalized surface. The dual controlled assembly of β-CD Au NPs on the surface enabled to use two stimuli as inputs for logic gate activation; the coupling between the localized surface plasmon, associated with the Au NP, and the surface plasmon wave, associated with the thin metal surface, is implemented as readout signal for "AND" logic gate operations.     

Silver hierarchical bowl-like array: synthesis, superhydrophobicity, and optical properties

We present a facile synthetic route to a silver bowl-like array film with hierarchical structures on glass substrate using the colloidal monolayer as a template. In these special hierarchical structures, microstructures were provided by a colloidal template of polystyrene latex spheres and nanostructures resulting from the thermal decomposition of silver acetate. These structures were chemically modified with 1-hexadecanethiol, and a corresponding self-assembled monolayer (SAM) was formed on their surfaces. Due to the lotus leaf-like morphology with hierarchical micro/nanostructures, the film displayed an extraordinary superhydrophobicity after chemical modification. Water contact angle and sliding angle were 169 degrees and 3 degrees (the weight of water droplets: 3 mg), respectively. Additionally, its optical property has also been investigated. This structure could be used in microfluidic devices, optical devices, and biological science.     

Oriented binding of the His6-tagged carboxyl-tail of the L-type Ca2+ channel alpha1-subunit to a new NTA-functionalized self-assembled monolayer

Oriented stable binding of functional proteins on surfaces is of fundamental interest for receptor/ligand studies in atomic force microscopy (AFM) and surface plasmon resonance (SPR) experiments. Here we have chosen the His6-tagged carboxyl-tail (C-tail) of the alpha1c-subunit of the L-type Ca2+ channel and calmodulin (CaM) as its cognitive partner as a model system to develop a new functional surface. Covalently attached self-assembled monolayers on ultraflat gold containing NTA-thiols to which the His6-tagged C-tail was bound and thiols with triethylene-glycol groups as matrix-thiols represented the system of choice. The topography of this surface was characterized using AFM; its ability to bind C-tail proteins oriented and stable was confirmed by SPR measurements and by complementary force spectroscopy experiments with a CaM4-construct covalently attached to the tip. The developed anchoring strategy can now be used to study receptor/ligand interactions in general applying force spectroscopy and SPR on His6-tagged proteins oriented immobilized onto this new NTA-functionalized self-assembled monolayer.     

Surface plasmon resonance and electrochemistry characterization of layer-by-layer self-assembled DNA and Zr4+ thin films, and their interaction with cytochrome c

Through electrostatic layer-by-layer (LbL) assembly, negatively charged calf thymus double stranded DNA (CTds-DNA), and positively charged Zr⁴⁺ ions were alternately deposited on gold substrate modified with chemisorbed cysteamine. Thus-prepared three-dimensional DNA networks were characterized by surface plasmon resonance (SPR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS). SPR spectroscopy indicates that the effective thickness of DNA monolayer in the (DNA/Zr⁴⁺)₁ bilayer was 1.5 ± 0.1 nm, which corresponds to the surface coverage of 79% of its full packed monolayer. At the same time, a linear increase of film thickness with increasing number of layers was also confirmed by SPR characterizations. The data of XPS and IR-RAS show that Zr⁴⁺ ions interact with both the phosphate groups and nitrogenous bases of DNA and load into the framework of DNA. Furthermore, the interactions between this composite film and heme protein cytochrome c (Cyt c) were investigated by SPR spectroscopy and electrochemistry. Compared with the adsorption of Cyt c on DNA monolayer, this composite multilayer film can obviously enhance the amount of immobilized Cyt c confirmed by SPR reflectivity-incident angle (R-θ) curves. Cyclic voltammetry (CV) indicates the Cyt c adsorbed on the composite film is electroactive, and the enhancement of peak current in CV indirectly verifies the increase of the amount of immobilized Cyt c.     

介孔SiO_2薄膜增敏SERS基底在消逝波激励下的特性表征

采用溶胶-凝胶分子模板法在50 nm厚金膜表面制备约40 nm厚介孔二氧化硅(MPS)薄膜,然后在MPS薄膜表面静电自组装金纳米粒子(GNP)单层膜,形成的多层膜结构用作表面增强拉曼散射(SERS)基底.利用扫描电镜观测到MPS薄膜具有表面开口多孔结构,有助于小分子向薄膜内快速扩散.基于时域有限差分(FDTD)方法对电场分布的仿真结果指出,在表面等离子体共振(SPR)条件下分布于金膜与GNP之间的消逝场显著增强.由于空间重叠,该增强场能够高效激发MPS内富集的小分子拉曼信号,产生的拉曼信号还可免受金属作用的干扰.利用Kretschmann结构和尼罗蓝(NB)拉曼活性分子测试了Au/MPS/GNP基底在785 nm激发波长下的SERS效果,并与Au/GNP基底进行了比较.结果表明,在SPR条件下,Au/MPS/GNP基底能够导致较强的定向和背向拉曼信号,而且在586 cm-1处的背向拉曼信号强度是Au/GNP基底的40倍,这归功于MPS薄膜.进一步测试表明背向拉曼信号强度与NB浓度成正相关.这意味着Au/MPS/GNP基底具有良好的半定量检测本领.     

Self-assembly to monolayer graphene film with high electrical conductivity

Monolayer chemically converted graphene (CCG) nanosheets can be homogeneously self-assembled onto silicon wafer modified by 3-aminopropyl triethoxysilane (APTES) to form very thin graphene film. The CCG film was characterized by FT-IR, XRD, SEM, TEM and AFM. Results show that CCG sheets formed monolayer film after assembled onto silicon wafer and there is a very tight chemical bond between sheets and wafer. Furthermore, the electrical measurements revealed that the monolayer graphene film has an excellent electrical conductivity.     

H2S-induced reorganization of mixed monolayer of carboxylic derivatives on silver surface

The structure of self-assembled monolayers ofp-terphenyl-4-carboxylic acid and the mixed monolayers of this acid with n-hexadecanoic acid on silver surface were studied by reflection-IR spectroscopy, near-edge X-ray absorption fine structure (NEXAFS) measurement, X-ray photoemission electron microscopy (X-PEEM), and atomic force microscopy. Exposure of the p-terphenyl-4-carboxylate monolayer to H2S vapor resulted in reorganization of the film structure into clusters of the corresponding free acids, in tens of nanometer dimension. Exposure of the mixed monolayer to H2S resulted in reorganization of the mixed monolayer film into phase-separated clusters of respective component molecules. The saturated aliphatic acid formed clusters of submicrometer size, whereas the p-terphenyl-4-carboxylic acid formed clusters of tens of nanometer size, presumably due to different surface mobility and/or intermolecular interaction of the two types of molecule. Restoration of the monolayer film from the clusters, driven by the reaction between the free acid molecules and the basic surface sites, proceeded at different speeds for the two types of molecules. The saturated acid monolayer was restored much faster than the p-terphenyl-4-carboxylic acid monolayer. A domain-separated monolayer in several micrometers scale was obtained. The process was imaged by tapping mode atomic force microscopy.     

Surface stress, kinetics, and structure of alkanethiol self-assembled monolayers

The surface stress induced during the formation of alkanethiol self-assembled monolayers (SAMs) on gold from the vapor phase was measured using a micromechanical cantilever-based chemical sensor. Simultaneous in situ thickness measurements were carried out using ellipsometry. Ex situ scanning tunneling microscopy was performed in air to ascertain the final monolayer structure. The evolution of the surface stress induced during coverage-dependent structural phase transitions reveals features not apparent in average ellipsometric thickness measurements. These results show that both the kinetics of SAM formation and the resulting SAM structure are strongly influenced both by the surface structure of the underlying gold substrate and by the impingement rate of the alkanethiol onto the gold surface. In particular, the adsorption onto gold surfaces having large, flat grains produces high-quality self-assembled monolayers. An induced compressive surface stress of 15.9 +/- 0.6 N/m results when a c(4x2) dodecanethiol SAM forms on gold. However, the SAMs formed on small-grained gold are incomplete and an induced surface stress of only 0.51 +/- 0.02 N/m results. The progression to a fully formed SAM whose alkyl chains adopt a vertical (standing-up) orientation is clearly inhibited in the case of a small-grained gold substrate and is promoted in the case of a large-grained gold substrate.     

Fabrication of Carbon Nanotube Thin Films for Flexible Transistors by Using a Cross-Linked Amine Polymer

Owing to their remarkable properties, single-walled carbon nanotube thin-film transistors (SWCNT-TFTs) are expected to be used in various flexible electronics applications. To fabricate SWCNT channel layers for TFTs, solution-based film formation on a self-assembled monolayer (SAM) covered with amino groups is commonly used. However, this method uses highly oxidized surfaces, which is not suitable for flexible polymeric substrates. In this work, a solution-based SWCNT film fabrication using methoxycarbonyl polyallylamine (Moc-PAA) is reported. The NH₂-terminated surface of the cross-linked Moc-PAA layer enables the formation of highly dense and uniform SWCNT networks on both rigid and flexible substrates. TFTs that use the fabricated SWCNT thin film exhibited excellent performance with small variations. The presented simple method to access SWCNT thin film accelerates the realization of flexible nanoelectronics.