In situ sensing of metal ion adsorption to a thiolated surface using surface plasmon resonance spectroscopy

The kinetics of the adsorption of metal ions onto a thiolated surface and the selective and quantitative sensing of metal ions were explored using surface plasmon resonance (SPR) spectroscopy. The target metal ion was an aqueous solution of Pt2+ and a thin-gold-film-coated glass substrate was modified with 1,6-hexanedithiol (HDT) as a selective sensing layer. SPR spectroscopy was used to examine the kinetics of metal ion adsorption by means of the change in SPR angle. The selectivity of the thiolated surface for Pt2+ over other divalent metal ions such as Cu2+, Ni2+, and Cd2+ was evident by the time-resolved SPR measurement. SPR angle shift, deltatheta(SPR), was found to increase logarithmically with increasing concentration of Pt2+ in the range of 1.0 x 10(-5)-1.0 mM. The rate of Pt2+ adsorption on HDT observed at both 0.1 and 1 mM Pt2+ accelerates until the surface coverage reaches approximately 17%, after which the adsorption profile follows Langmuirian behavior with the surface coverage. The experimental data indicated that heavy metal ions were adsorbed to the hydrophobic thiolated surface by a cooperative mechanism. A mixed self-assembled monolayer (SAM) composed of HDT and 11-mercaptoundecanoic acid was used to reduce the hydrophobicity of the thiol-functionalized surface. The addition of hydrophilic groups to the surface enhanced the rate of adsorption of Pt2+ onto the surface. The findings show that the adsorption of metal ions is strongly dependent upon the hydrophilicity/hydrophobicity of the surface and that the technique represents an easy method for analyzing the adsorption of metal ions to a functionalized surface by combining SPR spectroscopy with a SAM modification.     

A Sensitive Nanoporous Gold-Based Electrochemical DNA Biosensor for Escherichia coli Detection

A sensitive electrochemical DNA biosensor based on a mixed monolayer structure self-assembled at nanoporous gold (NPG) electrode surface was prepared for Escherichia coli (E. coli) detection. The NPG was fabricated on gold electrode, onto which thiolated oligonucleotides (SH-DNA) and mercaptohexanol (MCH) were covalently linked forming a mixed self-assembled monolayer (SAM). The hybridization between the SH-DNA/MCH modified biosensor and E. coli DNA was monitored with differential pulse voltammetry measurement using methylene blue (MB) as the hybridization indicator. The biosensor can detect 1 × 10^?12 M DNA target and 50 cfu/μL E. coli without any nucleic acid amplification steps. The detection limit was lowered to 50 cfu/mL after 5.0 h of incubation.     

Selective DNA detection at Zeptomole level based on coulometric measurement of gold nanoparticle-mediated electron transfer across a self-assembled monolayer

A selective DNA sensing with zeptomole detection level is developed based on coulometric measurement of gold nanoparticle (AuNPs)-mediated electron transfer (ET) across a self-assembled monolayer on the gold electrode. After immobilization of a thiolated hairpin-structured DNA probe, an alkanethiol monolayer was self-assembled on the resultant electrode to block [Fe(CN)6 ]-3-/4in a solution from accessing the electrode. In the presence of DNA target, hybridization between the DNA probe and the DNA target breaks the stem duplex of DNA probe. Consequently, stem moiety at the 3′-end of the DNA probes was removed from the electrode surface and made available for hybridization with the reporter DNA-AuNPs conjugates (reporter DNA-AuNPs). The thiolated reporter DNA matches the stem moiety at the 3′-end of the DNA probe. AuNPs were then enlarged by immersing the electrode in a growth solution containing HAuCl 4 and H2O2 after the reporter DNA-AuNPs bound onto the electrode surface. The enlarged AuNPs on the electrode restored the ET between the electrode and the [Fe(CN)6]3 -/4- , as a result, amplified signals were achieved for DNA target detection using the coulometric measurement of Fe(CN)6 3- electro-reduction by prolonging the electrolysis time. The quantities of ET on the DNA sensor increased with the increase in DNA target concentration through a linear range of 3.0 fM to 1.0 pM when electrolysis time was set to 300 s, and the detection limit was 1.0 fM. Correspondingly, thousands of DNA (zeptomole) copies were detected in 10L samples. Furthermore, the DNA sensor showed excellent differentiation ability for single-base mismatch.     

Electrochemical Quantitative Analysis of Nucleic Acids Using β‐Cyclodextrin Modified Gold Electrode

We present an electrochemical biosensor for the analysis of nucleic acids upon hybridization on the β‐cyclodextrin (β‐CD)‐modified gold electrode. The strategy is based on the following: The 5’‐ferrocene‐labeled single stranded capture probe DNA (5’‐fc‐ss‐DNA) was incorporated into the cavity of thiolated β‐CD which was immobilized on the surface of gold electrode. After hybridization of complementary target DNA, hybridized double stranded DNA (ds‐DNA) was released from the cavity of β‐CD. The difference of electrochemical properties on the modified gold electrode was characterized by cyclic voltametry and surface plasmon resonance. We successfully applied this method to the investigation of the sensor responses due to hybridization on various concentrations of applied target DNA. As a result, the label‐free electrochemical DNA sensor can detect the target DNA with a detection limit of 1.08 nM. Finally, our method does not require either hybridization indicators or other signalling molecules such as DNA intercalaters which most of electrochemical hybridization detection systems require.     

Enzyme-free surface plasmon resonance aptasensor for amplified detection of adenosine via target-triggering strand displacement cycle and Au nanoparticles

Herein, we combine the advantage of aptamer technique with the amplifying effect of an enzyme-free signal-amplification and Au nanoparticles (NPs) to design a sensitive surface plasmon resonance (SPR) aptasensor for detecting small molecules. This detection system consists of aptamer, detection probe (c-DNA1) partially hybridizing to the aptamer strand, Au NPs-linked hairpin DNA (Au-H-DNA1), and thiolated hairpin DNA (H-DNA2) previously immobilized on SPR gold chip. In the absence of target, the H-DNA1 possessing hairpin structure cannot hybridize with H-DNA2 and thereby Au NPs will not be captured on the SPR gold chip surface. Upon addition of target, the detection probe c-DNA1 is forced to dissociate from the c-DNA1/aptamer duplex by the specific recognition of the target to its aptamer. The released c-DNA1 hybridizes with Au-H-DNA1 and opens the hairpin structure, which accelerate the hybridization between Au-H-DNA1 and H-DNA2, leading to the displacement of the c-DNA1 through a branch migration process. The released c-DNA1 then hybridizes with another Au-H-DNA1 probe, and the cycle starts anew, resulting in the continuous immobilization of Au-H-DNA1 probes on the SPR chip, generating a significant change of SPR signal due to the electronic coupling interaction between the localized surface plasma of the Au NPs and the surface plasma wave. With the use of adenosine as a proof-of-principle analyte, this sensing platform can detect adenosine specifically with a detection limit as low as 0.21 pM, providing a simple, sensitive and selective protocol for small target molecules detection.     

DNA recognition interfaces: the influence of interfacial design on the efficiency and kinetics of hybridization

The effect of the surface chemistry of DNA recognition interfaces on DNA hybridization at a gold surface was investigated using both electrochemistry and the quartz crystal microbalance (QCM) technique. Different DNA recognition interfaces were prepared using a two-component self-assembled monolayer consisting of thiolated 20-mer probe single-stranded DNA (ss-DNA) containing either a 3'-mercaptopropyl or a 3'-mercaptohexyl linker group and an alcohol-terminated diluent layer with 2-, 6-, or 11-carbon length. The influence of the interfacial design on the hybridization efficiency, the affinity constant (Ka) describing hybridization, and the kinetics of hybridization was assessed. It was found that the further the DNA was above the surface defined by the diluent layer the higher the hybridization efficiency and Ka. The kinetics of DNA hybridization was assessed using both a QCM and an electrochemical approach to ascertain the influence of the interface on both the initial binding of target DNA to the surface and the formation of a complete duplex. These measurements showed that the length of the diluent layer has a large impact on the time taken to form a perfect duplex but no impact on the initial recognition of the target DNA by the immobilized probe DNA.     

Designs of Enterobacteriaceae Lac Z Gene DNA Gold Screen Printed Biosensors

This paper describes specific electrochemical enterobacteriaceae lac Z gene DNA sensors based on immobilization of a thiolated 25 base single stranded probe onto disposable screen printed gold electrodes (gold SPEs). Two configurations have been evaluated. In the first one, the capture probe was attached to the electrode surface through its ? SH moiety, while mercaptohexanol (MCH) was used as spacer for the displacement of nonspecifically adsorbed oligonucleotide molecules. The hybridization event between the probe and target DNA sequences was detected at ?0.20 V by square‐wave voltammetry (SWV), using methylene blue (MB) as electrochemical indicator. The second genosensor configuration involved modification of gold high temperature SPEs with a 3,3′‐dithiodipropionic acid di(N‐succinimidyl ester) (DTSP) self‐assembled monolayer (SAM). Moreover, 2‐aminoethanol was used as blocking agent, and further modification with avidin allowed binding of the biotinylated enterobacteriaceae lac Z gene DNA probe. An enzyme amplified detection scheme was applied, based on the coupling of streptavidin‐peroxidase to the biotinylated complementary target, after the hybridization process, and immobilization of tetrathiafulvalene (TTF) as redox mediator atop the modified electrode. The amperometric response obtained at ?0.15 V after the addition of hydrogen peroxide was used to detect the hybridization process. Experimental variables concerning sensors composition and electrochemical transduction were evaluated in both cases. A better precision and reproducibility in the fabrication process, as well as a higher sensitivity were achieved using the biotinylated probe‐based sensor configuration. A limit of detection of 0.002 ng/μL was obtained without any preconcentration step.     

Electrochemical biosensor for detection of BCR/ABL fusion gene based on hairpin locked nucleic acids probe

This communication reports on a novel biosensor to study the hybridization specificity by using thiolated hairpin locked nucleic acids (LNA) as the capture probe. The LNA probe was immobilized on the gold electrode through sulfur–Au interaction and could selectively hybridize with its target DNA. Differential pulse voltammetry (DPV) was used to monitor the hybridization reaction on the probe electrode. The decrease of the peak current of methylene blue, an electroactive indicator, was observed upon hybridization of the probe with the target DNA. The results indicated this new method has excellent specificity for single-base mismatch and complementary after hybridization, and a high sensitivity. This LNA probe has been used for assay of fusion gene in Chronic Myelogenous Leukemia (CML) of the real sample with satisfactory result.     

Electrochemical Detection of DNA Hybridization Based on the Probe Labeled with Carbon‐Nanotubes Loaded with Silver Nanoparticles

A sensitive electrochemical method for the detection of DNA hybridization based on the probe labeled with multiwall carbon‐nanotubes (MWNTs) loaded with silver nanoparticles (Ag‐MWNTs) has been developed. MWNTs were electroless‐plated with a large number of silver nanoparticles to form Ag‐MWNTs. Probe single strand DNA (ss‐DNA) with a thiol group at the 3′‐terminal labeled with Ag‐MWNTs by self‐assembled monolayer (SAM) technique was employed as an electrochemical probe. Target ss‐DNA with a thiol group was immobilized on a gold electrode by SAM technique and then hybridized with the electrochemical probe. Binding events were monitored by differential pulse voltammetric (DPV) signal of silver nanoparticles. The signal difference permitted to distinguish the match of two perfectly complementary DNA strands from the near perfect match where just three base pairs were mismatched. There was a linear relation between the peak current at +120 mV (vs. SCE) and complementary target ss‐DNA concentration over the range from 3.1×10^?14 to 1.0×10^?11 mol/L with a detection limit of 10 fmol/L of complementary target ss‐DNA. The proposed method has been successfully applied to detection of the DNA sequence related to cystic fibrosis. This work demonstrated that the MWNTs loaded with silver nanoparticles offers a great promising approach for sensitive detection of DNA hybridization.     

Hybridization detection of enzyme-labeled DNA at electrically heated electrodes

In this report we describe an electrochemical DNA hybridization sensor approach, in which signal amplification is achieved using heated electrodes together with an enzyme as DNA-label. On the surface of the heatable low temperature co-fired ceramic (LTCC) gold electrode, an immobilized thiolated capture probe was hybridized with a biotinylated target using alkaline phosphatase (SA-ALP) as reporter molecule. The enzyme label converted the redox-inactive substrate 1-naphthyl phosphate (NAP) into the redox-active 1-naphthol voltammetrically determined at the modified gold LTCC electrode. During the measurement only the electrode was heated leaving the bulk solution at ambient temperature. Elevated temperature during detection led to increased enzyme activity and enhanced analytical signals for DNA hybridization detection. The limit of detection at 53 °C electrode temperature was 1.2 nmol/L.     

Gold nanoparticles chemisorbed by a terphenyldithiol self-assembled monolayer for fabrication of a protein biosensor

In this study, improved detection of bovine serum albumin (BSA) was achieved by use of a fabricated surface plasmon resonance (SPR) biosensor. Terphenyldithiol (TPDT) was self-assembled on a gold substrate, then gold nanoparticles (Au-NPs) were chemisorbed on to the TPDT monolayer by strong bonding with the terminal thiol groups of the TPDT. The new sensor obtained was tested for immobilization of protein. The SPR results revealed much better detection of BSA by Au-NPs chemisorbed on the TPDT self-assembled monolayer (SAM) than by the bare SAM on the gold substrate.     

Dendrimer-functionalized self-assembled monolayers as a surface plasmon resonance sensor surface

We report here a multistep route for the immobilization of DNA and proteins on chemically modified gold substrates using fourth-generation NH(2)-terminated poly(amidoamine) dendrimers supported by an underlying amino undecanethiol (AUT) self-assembled monolayer (SAM). Bioactive ultrathin organic films were prepared via layer-by-layer self-assembly methods and characterized by fluorescence microscopy, variable angle spectroscopic ellipsometry, atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and attenuated total internal reflection Fourier transform infrared spectroscopy (ATR-FTIR). The thickness of the AUT SAM base layer on the gold substrates was determined to be 1.3 nm from ellipsometry. Fluorescence microscopy and AFM measurements, in combination with analyses of the XPS/ATR-FTIR spectra, confirmed the presence of the dendrimer/biopolymer molecules on the multilayer sensor surfaces. Model proteins, including streptavidin and rabbit immunoglobulin proteins, were covalently attached to the dendrimer layer using linear cross-linking reagents. Through surface plasmon resonance measurements, we found that sensor surfaces containing a dendrimer layer displayed an increased protein immobilization capacity, compared to AUT SAM sensor surfaces without dendrimer molecules. Other SPR studies also revealed that the dendrimer-based surfaces are useful for the sensitive and specific detection of DNA-DNA interactions. Significantly, the multicomponent films displayed a high level of stability during repeated regeneration and hybridization cycles, and the kinetics of the DNA-DNA hybridization process did not appear to be influenced by surface mass transport limiting effects.     

Characterization of grafting density and binding efficiency of DNA and proteins on gold surfaces

The surface grafting density of biomolecules is an important factor for quantitative assays using a wide range of biological sensors. We use a fluorescent measurement technique to characterize the immobilization density of thiolated probe DNA on gold and hybridization efficiency of target DNA as a function of oligonucleotide length and salt concentration. The results indicate the dominance of osmotic and hydration forces in different regimes of salt concentration, which was used to validate previous simulations and to optimize the performance of surface-stress based microcantilever biosensors. The difference in hybridization density between complementary and mismatched target sequences was also measured to understand the response of these sensors in base-pair mismatch detection experiments. Finally, two different techniques for immobilizing proteins on gold were considered and the surface densities obtained in both cases were compared.     

Studies on biotin–avidin indirect conjugated technology for a piezoelectric DNA sensor

Because of their high sensitivity, piezoelectric sensor techniques are extremely useful for environmental or clinical analysis. We developed a piezoelectric crystal DNA biosensor for the detection of the hybridization reaction based on the self-assembled monolayer technology and biotin–avidin system. 3,3′-Dithiopropionic acid was applied to form a self-assembled monolayer (SAM) on the gold surface of the quartz crystal. Avidin was coated on the gold electrode conjugated with 1-ethyl-3-[3-(dimethylamino)propyl]-carbodiimide (EDC) and N-hydroxysuccinimide (NHS), and then biotinylated nucleotide acids were immobilized on the gold electrode surface through the specific interaction of biotin and avidin. Our results indicated that, using this immobilization method, the piezoelectric DNA sensor shows a higher sensitivity and specificity in detecting the hybridization reaction. The sensor can be used repeatedly by electrode regeneration.     

Label-free electrochemical detection of DNA hybridization on gold electrode

A label-free electrochemical detection protocol for DNA hybridization is reported for the first time by using a gold electrode (AuE). The oxidation signal of guanine was monitored at +0.73 V by using square wave voltammetry (SWV) on self-assembled l-cysteine monolayer (SAM) modified AuE. The electrochemical determination of hybridization between an inosine substituted capture probe and native target DNA was also accomplished. 6-mer adenine probe was covalently attached to SAM via its amino link at 5^′ end. Then, 6-mer thymine-tag of the capture probe was hybridized with the adenine probe, thus left the rest of the oligonucleotide available for hybridization with the target. The dependence of the guanine signal upon the concentration of the target was observed. Probe modified AuE was also challenged with non-complementary and mismatch containing oligonucletides. Label-free detection of hybridization on AuE is greatly advantageous over the existing carbon and mercury electrode materials, because of its potential applicability to microfabrication techniques. Performance characteristics of the genosensor are described, along with future prospects.     

Comparison of different supramolecular architectures for oligonucleotide biosensing

This work describes a comparative study between two biosensing platforms that are commonly used to immobilize capture probes. These platforms refer to thiolated and biotinylated oligonucleotide strands chemisorbed on Au surfaces (DNA SAM) and bioconjugated on streptavidin (SA) monolayers (SA SAM), respectively. Both interfacial architectures were studied using surface acoustic wave (SAW) devices and surface plasmon spectroscopy (SPR). Our studies indicated that DNA SAM platforms enable higher densities of surface-confined oligonucleotide probes. However, their hybridization efficiency is lower when compared to that obtained in SA SAM platforms, thus impacting on a lower detection limit, 5 nM. Furthermore, binding of SA molecules to the biotinylated targets, in an attempt to enhance the signal in both platforms, revealed striking differences between both architectures. The SA underlayer used in the SA SAM configuration confers nonfouling characteristics to the interfacial assembly, thus precluding the nonspecific binding of SA onto the surface. The antifouling behavior of the SA DNA platform is an important feature to be considered in the amplification of hybridization events through the bioconjugation of biotinylated targets with streptavidin-based tags.     

Surface characterization and efficiency of a matrix-free and flat carboxylated gold sensor chip for surface plasmon resonance (SPR)

We report the preparation and characterization of a matrix-free carboxylated surface plasmon resonance (SPR) sensor chip with high sensing efficiency by functionalizing a bare gold thin film with a self-assembled monolayer of 16-mercaptohexadecanoic acid (SAM–MHDA chip). The self assembled monolayer surface coverage of the gold layer was carefully evaluated and the SAM was characterized by infrared reflection absorption spectroscopy, X-ray photoemission spectroscopy, atomic force microscopy, X-ray reflectivity-diffraction, and SPR experiments with bovine serum albumin. We compared the SPR signal obtained on this chip made of a dense monolayer of carboxylic acid groups with commercially available carboxylated sensor chips built on the same gold substrate, a matrix-free C1 chip, and a CM5 chip with a ~100 nm dextran hydrogel matrix (GE Healthcare). Two well-studied interaction types were tested, the binding of a biotinylated antibody (immunoglobulin G) to streptavidin and an antigen–antibody interaction. For both interactions, the well characterized densely functionalized SAM–MHDA chip gave a high signal-to-noise ratio and showed a gain in the availability of immobilized ligands for their partners injected in buffer flow. It thus compared favourably with commercially available sensor chips.     

DNA sensor based on an Escherichia coli lac Z gene probe immobilization at self-assembled monolayers-modified gold electrodes

A novel approach to construct an electrochemical DNA sensor based on immobilization of a 25 base single-stranded probe, specific to E. coli lac Z gene, onto a gold disk electrode is described. The capture probe is covalently attached using a self-assembled monolayer of 3,3′-dithiodipropionic acid di(N-succinimidyl ester) (DTSP) and mercaptohexanol (MCH) as spacer. Hybridization of the immobilized probe with the target DNA at the electrode surface was monitored by square wave voltammetry (SWV), using methylene blue (MB) as electrochemical indicator. Variables involved in the sensor performance, such as the DTSP concentration in the modification solution, the self-assembled monolayers (SAM) formation time, the DNA probe drying time atop the electrode surface and the amount of probe immobilized, were optimized.

A good stability of the single- and double-stranded oligonucleotides immobilized on the DTSP-modified electrode was demonstrated, and a target DNA detection limit of 45 nM was achieved without signal amplification. Hybridization specificity was checked with non-complementary and mismatch oligonucleotides. A single-base mismatch oligonucleotide gave a hybridization response only 7 ± 3%, higher than the signal obtained for the capture probe before hybridization. The possibility of reusing the electrochemical genosensor was also tested.     

Characterization of single- and double-stranded DNA on gold surfaces

Single- and double-stranded deoxy ribonucleic acid (DNA) molecules attached to self-assembled monolayers (SAMs) on gold surfaces were characterized by a number of optical and electronic spectroscopic techniques. The DNA-modified gold surfaces were prepared through the self-assembly of 6-mercapto-1-hexanol and 5'-C(6)H(12)SH -modified single-stranded DNA (ssDNA). Upon hybridization of the surface-bound probe ssDNA with its complimentary target, formation of double-stranded DNA (dsDNA) on the gold surface is observed and in a competing process, probe ssDNA is desorbed from the gold surface. The competition between hybridization of ssDNA with its complimentary target and ssDNA probe desorption from the gold surface has been investigated in this paper using X-ray photoelectron spectroscopy, chronocoulometry, fluorescence, and polarization modulation-infrared reflection absorption spectroscopy (PM-IRRAS). The formation of dsDNA on the surface was identified by PM-IRRAS by a dsDNA IR signature at approximately 1678 cm(-)(1) that was confirmed by density functional theory calculations of the nucleotides and the nucleotides' base pairs. The presence of dsDNA through the specific DNA hybridization was additionally confirmed by atomic force microscopy through colloidal gold nanoparticle labeling of the target ssDNA. Using these methods, strand loss was observed even for DNA hybridization performed at 25 degrees C for the DNA monolayers studied here consisting of attachment to the gold surfaces by single Au-S bonds. This finding has significant consequence for the application of SAM technology in the detection of oligonucleotide hybridization on gold surfaces.     

Voltammetric determination of DNA hybridization using methylene blue and self-assembled alkanethiol monolayer on gold electrodes

An electrochemical DNA biosensor based on the recognition of single stranded DNA (ssDNA) by hybridization detection with immobilized complementary DNA oligonucleotides is presented. DNA and oligonucleotides were covalently attached through free amines on the DNA bases using N-hydroxysulfosuccinimide (NHS) and N-(3-dimethylamino)propyl-N′-ethylcarbodiimide hydrochloride (EDC) onto a carboxylate terminated alkanethiol self-assembled monolayers (SAM) preformed on a gold electrode (AuE). Differential pulse voltammetry (DPV) was used to investigate the surface coverage and molecular orientation of the immobilized DNA molecules. The covalently immobilized probe could selectively hybridize with the target DNA to form a hybrid on the surface despite the bases being attached to the SAM. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with the target. Peak currents were found to increase in the following order: hybrid-modified AuE, mismatched hybrid-modified AuE, and the probe-modified AuE which indicates the MB signal is determined by the extent of exposed bases. Control experiments were performed using a non-complementary DNA sequence. The effect of the DNA target concentration on the hybridization signal was also studied. The interaction of MB with inosine substituted probes was investigated. Performance characteristics of the sensor are described.