Radium removal from aqueous solutions by adsorption on non-treated and chemically modified biomass by-product

The adsorption efficiency of a biomass by-product (olive cake) regarding the removal of radium (²²⁶Ra) from aqueous solutions has been investigated prior and after its chemical treatment. The chemical treatment of the biomass by-product included phosphorylation and MnO₂-coating. The separation/removal efficiency has been studied as a function of pH, salinity (NaCl) and calcium ion concentration (Ca²⁺) in solution. Evaluation of the experimental data shows clearly that the phosphorylated biomass by-product presents the highest adsorption capacity and efficiency followed by the MnO₂-coated material and the non-treated biomass by-product. However, regarding the effect of salinity and the presence of competitive cations (e.g. Ca²⁺) on the adsorption/removal efficiency, the MnO₂-coated material shows the lowest decline in efficiency (only 2 % of the relative adsorption efficiency) followed by the non-treated and the phosphorylated biomass by-product. The results of the present study indicate that depending on the physicochemical characteristics of the radium-contaminated water, all three types of the biomass by-product could be effectively used for the treatment of radium-contaminated waters. Nevertheless, the MnO₂-coated material is expected to be the most effective adsorbent and an alternative to MnO₂ resins for the treatment of environmentally relevant waters.     

U(VI) adsorption by biochar fiber–MnO2 composites

The removal of U(VI) by biochar fibers from aqueous solutions has been investigated prior and after MnO₂ surface-deposition. The removal efficiency has been studied as a function of pH, U(VI) concentration, ionic strength, temperature and contact time. The fibers morphology and surface complexes were analyzed by SEM–EDX and FTIR, respectively. Evaluation of the experimental data indicates that the composite presents extraordinary adsorption capacity (q_max = 3.8 mmol g⁻¹, 904 mg g⁻¹), which is attributed to the formation of inner-sphere surface complexes, and that the adsorption reaction is a relatively fast, endothermic and entropy-driven process.

     

基于医用纱布负载的二氧化锰纳米颗粒用于亚甲蓝染料的去除

以医用纱布(medical gauze,MG)同时作为模板和还原剂,通过原位氧化还原反应,简便地制备了MG负载的MnO₂纳米颗粒(MnO₂ NPs/MG),并对其形貌、成分进行表征。结果表明,MnO₂ NPs均匀地分散于MG纤维表面。结合MnO₂纳米材料的吸附性能和MG复合材料的操作便捷性,将MnO₂ NPs/MG进一步应用于亚甲蓝染料的去除。结果表明,在中性条件下,通过简单的浸泡搅拌,MnO₂ NPs/MG对亚甲蓝的去除率可达85.09%,并且可以通过增大吸附材料用量与染料初始浓度的比例提高去除率。等温吸附和动力学研究证明,MnO₂ NPs/MG对亚甲蓝的吸附符合Langmuir吸附等温模型和拟二级动力学模型。     

基于医用纱布负载的二氧化锰纳米颗粒用于亚甲蓝染料的去除

以医用纱布（medical gauze,MG）同时作为模板和还原剂,通过原位氧化还原反应,简便地制备了MG负载的MnO₂纳米颗粒（MnO₂ NPs/MG）,并对其形貌、成分进行表征。结果表明,MnO₂ NPs均匀地分散于MG纤维表面。结合MnO₂纳米材料的吸附性能和MG复合材料的操作便捷性,将MnO₂ NPs/MG进一步应用于亚甲蓝染料的去除。结果表明,在中性条件下,通过简单的浸泡搅拌,MnO₂ NPs/MG对亚甲蓝的去除率可达85.09%,并且可以通过增大吸附材料用量与染料初始浓度的比例提高去除率。等温吸附和动力学研究证明,MnO₂ NPs/MG对亚甲蓝的吸附符合Langmuir吸附等温模型和拟二级动力学模型。     

Sorption of americium from low-level liquid wastes by nanocrystalline MnO2

Nanocrystalline MnO₂, synthesized by alcoholic hydrolysis of KMnO₄, has been studied as a sorbent for removal of americium from low level liquid waste solutions. The synthesized MnO₂ was found to have BET surface area of 230 m² g^?1. Am(III) was found to be sorbed by MnO₂ quantitatively within 15 min at pH 5. The sorption was found to be more than 90 % at as low a pH as 1.2 and reached to near 100 % at all pH values above pH 3.0 There was no effect of ionic strength (0.01–1.0 M NaCl, CaCl₂) on the sorption suggesting the sorption following inner sphere complexation mechanism at all the pH values. Adsorption isotherm studies were carried out using Eu(III) as a chemical analogue of Am(III). These studies showed the isotherm data to follow Langmuir adsorption isotherm.     

Removal of Carbon Disulfide from Gas Streams Using Dielectric Barrier Discharge Plasma Coupled with MnO2 Catalysis System

The removal of gaseous carbon disulfide (CS₂) via dielectric barrier discharge (DBD) combined with MnO₂ catalysis has been investigated. CS₂ removal and energy yield (EY) had been examined as a function of catalyzer position in DBD reactor, initial CS₂ concentration, input power, and gas residence time. The results showed that DBD combined with MnO₂ catalyst can improve the CS₂ energy and removal efficiency, and MnO₂ catalyst placed in afterglow area can enhance the CS₂ removal efficiency by about 10 % as compared with DBD treatment only. When increasing initial CS₂ concentration and flow rate, a higher EY is obtained. The possible CS₂ removal pathways by DBD combined with MnO₂ were proposed based on the product identification by FT-IR.     

Photogenic MnO2/Ag metal nanocomposites and their dye adsorbing activities

• Manganese dioxide/silver (MnO₂/Ag) nanoparticles were fabricated by using KMnO₄-NaBH₄ redox reaction at room temperature. The optical and structural properties of MnO₂/Ag were determined using UV–visible and Fourier transform infrared spectroscopies. The morphology was established with scanning and transmission electron microcopies, and X-ray diffraction. MnO₂/Ag showed excellent adsorbing activity to the removal of Congo red. The various kinetic models were used to determine the rate of dye removal. Congo red adsorption onto MnO₂Ag proceeds through the pseudo-second-order kinetic model. Langmuir adsorption capacity (Q⁰_max = 97.1 mg/g), and sorption intensity (n = 1.6) were estimated with Langmuir and Freundlich adsorption isotherm models for 250 mg/L Congo red. Elovich model suggest the adsorption of Congo red with the MnO₂Ag proceeds through the film diffusion. The positive values of enthalpy changes (ΔH⁰), entropy changes (ΔS⁰), and negative Gibbs free energy changes (ΔG⁰) showed that the Congo red adsorption process was endothermic, spontaneous, and chemisorption process followed with physical mechanism. The results showed that the removal efficiency decreases from 98% to 89% after the six consecutive experiments.

     

Adsorption of uranium from aqueous solution by graphene oxide nanosheets supported on sepiolite

Adsorptive behavior of uranium from aqueous solution on graphene oxide supported on sepiolite composites (GO@sepiolite composites) as a function of pH, ionic strength, temperature and initial uranium concentration was carried out by the batch techniques. GO@sepiolite composites was synthesized and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and potentiometric acid–base titration. According to XRD patterns and SEM images, the graphene oxide nanosheets were grafted on sepiolite surface successfully. The macroscopic results showed that the adsorption of uranium on GO@sepiolite composites was significantly depended on pH, whereas no effect of ionic strength on uranium adsorption at high pH and high ionic strength conditions was observed. The uptake equilibrium is best described by Langmuir adsorption isotherm, and the maximum adsorption capacity (Q_e) of GO@sepiolite composites at pH 5.0 and T = 298 K were calculated to be 161.29 mg/g. Thermodynamic results indicated that the adsorption of uranium on GO@sepiolite composites is the spontaneous and exothermic process.     

Adsorption of hexavalent uranium on biomass by-product

The effectiveness of the uranium removal by olive cake from aqueous solutions has been demonstrated in batch type experiments under normal atmospheric conditions. The adsorption capacity has been evaluated by using both Langmuir and Freundlich isotherms. The optimum pH regarding for uranium adsorption on olive cake is 7.5. The amount of adsorbed uranium is governed by the amount of active sites on the biomass surface indicating an inner sphere complexation. The adsorption of uranium on olive cake is an endothermic and entropy-driven process and does not depend on the ionic strength of the solution.     

Zirconium removal from uranium/hydrogen carbonate solutions by adsorption on managanese dioxide

In order to determine the best conditions for removing⁹⁵Zr from uranium/hydrogen carbonate solutions, the adsorption behavior of fission product⁹⁵Zr on hydrated MnO₂ as a function of HCO ₃ ^– ion molarity has been studied both in the presence and absence of uranium. Batch experiments showed that the maximum⁹⁵Zr uptake occurred at low HCO ₃ ^– concentration, both in uranium-free and uranium (at a constant molarity of 0.02) containing solutions, the relative⁹⁵Zr uptake being lower when uranium was present in the solution. Conversely, when the HCO ₃ ^– concentration augmented beyond 0.10M, the⁹⁵Zr uptake was higher for the uranium containing solution. Concerning this last case, the maximum⁹⁵Zr uptake was found at a 0.06M HCO ₃ ^– concentration. However at this HCO ₃ ^– concentration, uranium was observed to precipitate and thus, a HCO ₃ ^– concentration of 0.12M was chosen to perform the dynamic⁹⁵Zr removal by MnO₂ from uranium/hydrogen carbonate solutions. Under these conditions, the⁹⁵Zr removal reached 99%.     

Uranium removal from aqueous solutions by wood powder and wheat straw

The influence of initial uranium concentration, solution pH, contact time and adsorbent mass was investigated for removal of uranium from aqueous solutions by pine wood powder and wheat straw using a batch technique. The maximum removal efficiency of uranium achieved at pH 8 and 7 for pine wood powder and wheat straw, respectively. Langmuir and Freundlich adsorption isotherms and three kinetic models of adsorption including; Elovich, Lagergren pseudo-first and Lagergren pseudo-second order were used to describe the adsorption mechanisms. The uranium sorption onto wood and wheat straw powders followed a Freundlich isotherm. The kinetic studies showed that the data fitted very well to the pseudo-second order model in the studied concentration range of uranium for both adsorbents. Uranium desorption from loaded adsorbents also studied using batch techniques as a function of desorptive reagent, desorption time and desorptive reagent concentration. The results of the experiment indicated that the optimum desorption efficiency of uranium for wood powder and wheat straw occurred in 5 min shaking time, using 1.5 M HNO₃ and 2 M Na₂CO₃ solutions, respectively.     

The Removal of Victoria Blue from Aqueous Solution by Adsorption on a Low-Cost Material

The use of perlite for the removal of victoria blue from aqueous solution at different concentration, ionic strength, pH and temperature has been investigated. Adsorption process is attained to the equilibrium within 1 h. It is found that the adsorption capacity of perlite samples for the removal of victoria blue increased by increasing pH and temperature, and decreased by expansion and ionic strength. The adsorption isotherms are described by means of the Langmuir and Freundlich isotherms. The adsorption isotherm was measured experimentally at different conditions, and the experimental data were correlated reasonably well by the adsorption isotherm of the Langmuir, and the isotherm parameters (Q _m and K) have been calculated for perlite samples as well. It is concluded that victoria blue is physically adsorbed onto the perlite. The removal efficiency (P) and dimensionless seperation factor (R) have shown that perlite can be used for removal of victoria blue from aqueous solutions, but unexpanded perlite is more effective.     

Adsorption of polyallylamine to lignocellulosic fibres: effect of adsorption conditions on localisation of adsorbed polyelectrolyte and mechanical properties of resulting paper sheets

Cationic polyallylamine (PAH), was adsorbed onto lignocellulosic fibres, and a fluorescent label on the polyelectrolyte enabled its location to be shown by confocal fluorescence microscopy. The adsorption time and ionic strength were varied to study their effect on the localisation of the adsorbed PAH. The microscopy showed that a long adsorption time, 24 h, and a high ionic strength, 10⁻¹ M NaCl + 5 × 10⁻³ M NaHCO₃ or higher, resulted in the adsorption of polyallylamine throughout the fibre walls. Shorter adsorption times and/or lower ionic strength resulted in adsorption only to the fibre exterior. By preparing sheets from fibres with polyelectrolyte adsorbed either to the exterior parts or into the fibre cell wall and testing their mechanical behaviour, a link was established between the localisation of adsorbed polyelectrolyte and the mechanical properties. Adsorption to the fibre exterior led to an increase in tensile strength and strain at break. The creep deformation at 90%RH was also slightly reduced by the adsorption of low molecular weight PAH (15 kDa). When polyallylamine was adsorbed throughout the wall of the lignocellulosic fibres, the mechanical properties were not however improved and the creep deformation at 90%RH actually increased somewhat.     

In situ synthesis of MnO<Subscript>2</Subscript>-loaded biocomposite based on microcrystalline cellulose for Pb<Superscript>2+</Superscript> removal from wastewater

We fabricated a new MnO₂-loaded biocomposite based on microcrystalline cellulose (MCC–MnO₂) by an in situ synthesis method and investigated its adsorption behavior and mechanism for Pb²⁺ removal from aqueous medium. As-prepared MCC–MnO₂ was characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) analyses. The effects of pH value, initial Pb²⁺ concentration, contact time, and solution temperature on the uptake of Pb²⁺ onto MCC–MnO₂ were investigated using a batch system. Adsorption equilibrium could be achieved in 3 h for various studied initial concentrations, and a pseudo-second-order model could fit the adsorption behavior well. The equilibrium data could be well described by the Langmuir isotherm model, and the maximum monolayer adsorption capacity of MCC–MnO₂ (with 7.98% MnO₂ loading) for Pb²⁺ was estimated to be 247.5 mg/g at 313 K. Thermodynamic studies indicated a spontaneous and endothermic adsorption process. X-ray photoelectron spectroscopy (XPS) was used to analyze the adsorption mechanism, revealing that the chemical speciation of Pb²⁺ on MCC–MnO₂ was similar to the compound PbO. Moreover, no variations in the valence of Mn were observed after adsorbing Pb²⁺. The regeneration study showed that the adsorption capacity retained about 89.6% of its initial value at the fifth sequential regeneration cycle, indicating that this material is an efficient and renewable hybrid adsorbent for Pb²⁺ removal.     

Influence of Surface Coating on Fluoride Removal by Magnetite

Al(OH)₃- and ZrO(OH)₂-coated magnetites were prepared and used for fluoride removal from aqueous samples. The influence of pH, sorbent mass, and ions such as chloride, sulfate, and phosphate on the removal of fluoride was characterized. The sorption process was highly pH dependent, and the optimal sorption was obtained from pH 4 to 5 for ZrO(OH)₂- and pH 4 to 7 for Al(OH)₃-coated magnetites. The sorption isotherm was well described by the Langmuir equation for the sorbents. The maximum adsorption capacity of ZrO(OH)₂-coated magnetite (57.47?mg-F?g^?1-sorbent) was higher than for Al(OH)₃-coated magnetite (23.87?mg-F?g^?1-sorbent). The ion-exchange reaction occurred in 5?min and more than 99% of fluoride was removed from solution. When the ZrO(OH)₂-coated magnetite was used, the presence of foreign ions negatively affected the fluoride removal. The prepared sorbents showed an excellent performance for the removal of fluoride in water samples.     

Extrapolation studies on adsorption of thorium and uranium at different solution compositions on soil sediments

Study on adsorption of thorium and uranium radionuclides by a soil sediment as a function of ionic composition of Ca, Mg and Na has been carried out. Experimentally determined slopes represents an average of adsorption on soil sediments having different relative affinities for thorium, uranium, calcium and magnesium. Both thorium and uranium were found to be adsorbed to ion-exchange sites together with calcium and magnesium cations as effective competitors An extrapolated equation for the distribution coefficientK _d was formed for both radionuclides thorium and uranium at the specified site where the soil sediments were sampled. The combined cation concentration of both calcium and magnesium in solution correlates linearly with the measuredK _d ^Th,U values.     

Preparation,characterization and application of a CTAB-modified nanoclay for the adsorption of an herbicide from aqueous solutions: Kinetic and equilibrium studies

In this study, surfactant-modified pillared montmorillonites (MMT) were prepared using cetyltrimethylammonium bromide (CTAB) by the intercalation method and used as adsorbent to remove bentazon from aqueous solutions. The main compositions of MMT and CTAB/MMT were characterized by Fourier transform–infrared spectroscopy (FT–IR), X-ray diffraction (XRD), scanning electron micrography (SEM) and energy dispersive X-ray (EDX) spectroscopy. The removal efficiency of bentazon was studied as a function of adsorbent dosage, pH, initial bentazon concentration and ionic strength (sodium carbonate, sodium bicarbonate, sodium sulfate and sodium chloride). The removal efficiency of bentazon by CTAB/MMT was more than that of MMT in similar conditions. By increasing adsorbent dosage and initial bentazon concentration, the removal efficiency was increased and declined, respectively. The results showed that the maximum adsorption of organo-modified montmorillonite was obtained at pH 3. The maximum adsorption capacity was estimated to be 500 mg/g at pH 3 and room temperature. The study of the adsorption kinetic model revealed that the pseudo-second order model was the best applicable one to describe the adsorption of bentazon onto CTAB/MMT. Adsorption data were analyzed by both Langmuir and Freundlich adsorption isotherms and the results showed that it was better described by the Langmuir model. The adsorption capacities of the samples were found to increase with Na₂CO₃ anion saturation, while they decreased in the presence of NaHCO₃, Na₂SO₄ and NaCl.     

Preparation of carbon coated Fe3O4 nanoparticles for magnetic separation of uranium

Uranium(VI) was removed from aqueous solutions using carbon coated Fe₃O₄ nanoparticles (Fe₃O₄@C). Batch experiments were conducted to study the effects of initial pH, shaking time and temperature on uranium sorption efficiency. It was found that the maximum adsorption capacity of the Fe₃O₄@C toward uranium(VI) was ∼120.20 mg g⁻¹ when the initial uranium(VI) concentration was 100 mg L⁻¹, displaying a high efficiency for the removal of uranium(VI) ions. Kinetics of the uranium(VI) removal is found to follow pseudo-second-order rate equation. In addition, the uranium(VI)-loaded Fe₃O₄@C nanoparticles can be recovered easily from aqueous solution by magnetic separation and regenerated by acid treatment. Present study suggested that magnetic Fe₃O₄@C composite particles can be used as an effective and recyclable adsorbent for the removal of uranium(VI) from aqueous solutions.     

Preparation and Pb (II) adsorption in aqueous of 2D/2D g‐C3N4/MnO2 composite

A novel g‐C₃N₄/MnO₂ composite was prepared by in situ deposition of MnO₂ on graphitic carbon nitride (g‐C₃N₄) nanosheets, and its adsorption properties were evaluated for removal of Pb (II) in aqueous. Fourier transform‐infrared, spectrometer scanning electron microscopy and transmission electron microscopy characterization showed the g‐C₃N₄/MnO₂ composite had a two‐dimensional/two‐dimensional (2D/2D) structure with ample active sites. The Brunauer–Emmett–Teller specific surface area of g‐C₃N₄/MnO₂ composites (234.9 m²/g) was 13.5 times larger than that of g‐C₃N₄ (17.37 m²/g), providing better conditions for adsorption. The adsorption kinetic data were better fitted with the pseudo‐second‐order model. The Langmuir model was more suitable for describing the experimental equilibrium data of g‐C₃N₄/MnO₂, and the maximum adsorption capacity was 204.1 mg/g for Pb (II). The adsorption of g‐C₃N₄/MnO₂ composite for Pb (II) was an endothermic and spontaneous process, and reached adsorption equilibrium rapidly within initial 150 min. This composite was an excellent adsorbent because of its higher adsorption capacity and facile preparation progress.     

<Superscript>99m</Superscript>Tc production via the (<Emphasis Type="Italic">γ, n</Emphasis>) reaction on natural Mo

In this paper, cheap liquorice residue was used to prepare activated carbon (AC), thioacetamide (TAA) was used to modify the AC, and the adsorption experiments were conducted in the simulated acid radioactive wastewater with low uranium concentration to study the adsorption behavior and mechanism for uranium by TAA modified AC (TAA–AC). The removal efficiency by TAA–AC was 92.1–98.2% from the 1 mg L^?1 uranium solution at pH 2–6. The adsorption equilibrium data were well fitted by Dubinin–Radushkevich model, and the maximum adsorption capacity was estimated to be 340 mg g^?1. TAA–AC showed an enhanced selectivity for uranium in the presence of competitive ions. Furthermore, the adsorption experiments were conducted in the actual acid radioactive wastewater with low uranium concentration from an in situ leach uranium mine. The high adsorption rate (98.3%) and selectivity (K_d?=?3.78×10⁴ mL g^?1) for uranium were observed in the actual acid radioactive wastewater, and the adsorption rate was found to maintain 96.2% over six cycles of adsorption–desorption.