A versatile sonication-assisted deposition–reduction method for preparing supported metal catalysts for catalytic applications

This work aims to develop a rapid and efficient strategy for preparing supported metal catalysts for catalytic applications. The sonication-assisted reduction–precipitation method was employed to prepare the heterogeneous mono- and bi-metallic catalysts for photocatalytic degradation of methyl orange (MO) and preferential oxidation (PROX) of CO in H₂-rich gas. In general, there are three advantages for the sonication-assisted method as compared with the conventional methods, including high dispersion of metal nanoparticles on the catalyst support, the much higher deposition efficiency (DE) than those of the deposition–precipitation (DP) and co-precipitation (CP) methods, and the very fast preparation, which only lasts 10–20 s for the deposition. In the AuPd/TiO₂ catalysts series, the AuPd(3:1)/TiO₂ catalyst is the most active for MO photocatalytic degradation; while for PROX reaction, Ru/TiO₂, Au–Cu/SBA-15 and Pt/γ-Al₂O₃ catalysts are very active, and the last one showed high stability in the lifetime test. The structural characterization revealed that in the AuPd(3:1)/TiO₂ catalyst, Au–Pd alloy particles were formed and a high percentage of Au atoms was located at the surface. Therefore, this sonication-assisted method is efficient and rapid in the preparation of supported metal catalysts with obvious structural characteristics for various catalytic applications.     

The preparation and characterization of nanoparticle TiO2/Ti films and their photocatalytic activity

Nanoparticle TiO₂/Ti films were prepared by a sol–gel process using Ti(OBu)₄ as raw material, the as-prepared film samples were also characterized by TG-DTA, XRD, TEM, SEM, XPS, DRS, PL, SPS and EFISPS testing techniques. TiO₂ nanoparticles experienced two processes of phase transition, i.e. amorphous to anatase and anatase to rutile at the calcining temperature range from 450 to 700 °C. TiO₂ nanoparticles calcined at 600 °C had similar composition, structure, morphology and particle size with the internationally commercial P-25 TiO₂ particles. Thus, the conclusion that 600 °C might be the most appropriate calcining temperature during the preparation process of nanoparticle TiO₂/Ti film photocatalysts could be made by considering the main factors such as the properties of TiO₂ nanoparticles, the adhesion of nanoparticle TiO₂ film to Ti substrate, the effects of calcining temperature on Ti substrate and the surface characteristics and morphology of nanoparticle TiO₂/Ti film for the practice view. The Ti element mainly existed on the nanoparticle TiO₂/Ti(3) film calcined at 600 °C as the chemical state of Ti⁴⁺, while O element mainly existed as three kinds of chemical states, i.e. crystal lattice oxygen, hydroxyl oxygen and adsorbed oxygen with increasing band energy. Its photoluminescence (PL) spectra with a peak at about 380 nm could be observed using 260 nm excitation, possibly resulting from the electron transition from the bottom of conduction band to the top of valence band. The PL peak position was nearly the same as the onset of its diffuse reflection spectra (DRS) and surface photovoltage spectroscopy (SPS), demonstrating that the effects of the quantum size on optical property were greater than that of the Coulomb and surface polarization. The PL spectra with two peaks related to the anatase and rutile, respectively, could be observed using the excited wavelength of 310 nm. Weak PL spectra could be observed using the excited wavelength of 450 nm, resulting from surface states. In addition, during the experimental process of the photocatalytic degradation phenol, the photocatalytic activity of nanoparticle TiO₂/Ti film with three layers calcined at 600 °C was the highest.     

A comparative DFT study of adsorption and catalytic performance of Au nanoparticles at anatase and brookite TiO2 surfaces

We have compared the adsorption properties of small Au_n (n = 1–8) nanoparticles on the defect-free (stoichiometric) and defective (partially reduced) brookite TiO₂(210) and anatase TiO₂(101) surfaces using density functional theory calculations. The interaction between Au atoms and anatase TiO₂(101) was determined to be quite weak and small Au_n particles grown at defects (O vacancies) prefer extended 2D structures. By contrast, dispersion and 3D configurations appear to be favored at brookite TiO₂(210) for Au_n nanoparticles due to their strong interaction. Calculations of CO oxidation at Au_n (n = 6–8) particles supported at defective brookite TiO₂(210) show that occurrence of protruding low-coordinated Au atoms is essential for favorable CO adsorption and subsequent reaction with O₂. In particular, the configuration of the Au_n nanoparticles can determine the energetics in the formation of active Au atoms, and their mobility also affects the reaction between CO and O₂ (or O).     

Characterization and relative sonocatalytic efficiencies of a new MWCNT and CdS modified TiO2 catalysts and their application in the sonocatalytic degradation of rhodamine B

TiO₂ nanoparticles modified with MWCNTs and CdS were synthesized by the sol–gel method followed by solvothermal treatment at low temperature. The chemical composition and surface structure of the CdS/CNT–TiO₂ composites were investigated by X-ray diffraction, specific surface area measurements, energy-dispersive X-ray spectroscopy, transmission electron microscopy, and scanning electron microscopy. Then a series of sonocatalytic degradation experiments were carried out under ultrasonic irradiation in the presence of CNT/TiO₂ and the CdS/CNT–TiO₂ composites. It was found that RhB was quickly and effectively degraded under different ultrasonic conditions. As expected, the nanosized CdS/CNT–TiO₂ photocatalyst showed enhanced activity compared with the non CdS treated CNT/TiO₂ material in the sonocatalytic degradation of RhB. The sonocatalyst CCTb with 34.68% contents of Ti heat treated at 500 °C for 1 h showed the highest sonocatalytic activity. The synergistic effect of the greater surface area and catalytic activities of the composite catalysts was examined in terms of their strong adsorption ability and interphase interaction by comparing the effects of different amounts of MWCNTs and CdS in the catalysts and their roles. The mechanism of sonocatalytic degradation over the CdS/CNT modified TiO₂ composites under different ultrasonic conditions was also discussed.     

An X-ray photoelectron spectroscopy investigation of a novel Pd–Pt colloid catalyst

A Bi-promoted charcoal-supported Pd–Pt oxidation catalyst prepared from colloidal NOct₄Cl-stabilized Pd–Pt nanoparticles was investigated by means of X-ray photoelectron spectroscopy (XPS). Pd 3d, Pt 4f, Bi 4f, C 1s and O 1s spectra of the colloid, the supported colloid catalyst and a conventional charcoal-supported Pd–Pt/Bi coimpregnation catalyst (Degussa, CEF 196 RA/W) were measured. Both catalysts were explored unused (as-prepared) and after deactivation in the heterogeneous catalytic oxidation of glucose to gluconic acid. The spectra are analyzed to elucidate the higher starting activity of the Pd–Pt/Bi/C colloid catalyst, especially the role of the promotor Bi and the mechanisms leading to catalyst deactivation. The higher starting activity of the colloid catalyst is explained by the presence of completely reduced Pd and Pt, threevalent Bi and a smaller particle size in contrast to the conventional catalyst which contains partly oxidized Pd and a non-unique chemical state of Bi. The deactivation of both catalysts is suggested to be due to metal dissolution, particle growth and chemical poisoning.     

不同晶相结构和形貌TiO2负载Ru催化剂的CO选择甲烷化

用水热法得到的钛酸纳米纤维前体,通过不同后处理方法合成了多种纳米结构的TiO₂．采用N₂等温吸附和BET比表面、X射线衍射、透射电镜和能量分散X射线分析表征了TiO₂及负载Ru催化剂的微结构,包括比表面、晶相结构和形貌以及Ru纳米颗粒尺寸分布等．对负载Ru催化剂在富氢条件下CO选择甲烷化反应活性测试表明：金红石相TiO₂和TiO₂-B为载体负载的Ru催化剂比锐钛矿相TiO₂负载的Ru催化剂表现出更高的反应性能．其活性区别说明了不同晶相结构和形貌TiO₂载体与Ru纳米颗粒的相互作用存在差异．     

Enhanced oxygen binding through surface mediated ionic bonds

Palladium clusters deposited on TiO₂ supports constitute important oxidation catalysts. Addition of O₂ in presence of deposited palladium clusters results in dissociated O atoms whose binding strength controls the activity of a catalytic oxidation reaction. Here we demonstrate how the presence of even remote Pd sites can more than double the energy required to remove surface O atoms from a surface. This unusual increase in binding is shown to originate in a Coulomb interaction between Pd^δ+ and O^δ? where the otherwise semiconducting support remains almost neutral acting to mediate a charge transfer from Pd to O sites. The O atoms supported on lattice Ti sites are further shown to form composite TiO motifs that can exchange sites with Pd atoms with a minimal energy, opening the pathway to Ti migration. This behavior is proposed to be linked to their identical valence pool containing d-states.     

Periodic density functional theory studies of the VOx/TiO2 (anatase) catalysts: Structure and stability of monomeric species

Periodic density functional theory has been utilized to investigate the structure and stability of monomeric HVO_x species on anatase support. The three most stable surfaces of anatase were investigated, namely the (001), (100) and (101) surfaces. Unlike previous theoretical studies it was found that on the (001) surface vanadia species with five-coordinated vanadium atom are more stable than those with tetrahedrally coordinated vanadium atom. On the other hand, on the (100) and (101) surfaces, the vanadium atom in the vanadia species is still tetrahedrally coordinated. The stability of different VO_x/TiO₂ structures which are not fully dehydrated has been systematically studied and the results show that the vanadia species on the three surfaces follow an order of TiO₂ (001) > TiO₂ (100) > TiO₂ (101). This can be understood from the acidity and basicity of the three anatase surfaces. The results suggest that monomeric VO_x species may be better stabilized if the support exposes more (001) surfaces. Our analyses on electronic structure of the most stable VO_x/TiO₂ structure (D₀₀₁) suggest that its bridging V–O–Ti oxygen atoms may have higher reactivity than the terminal vanadyl oxygen atoms.     

Palladium-ytterbium bimetallic electrocatalysts supported on carbon black,titanium suboxide,or poly(diallyldimethylammonium chloride)-functionalized titanium suboxide towards methanol oxidation in alkaline media

Palladium-ytterbium (Pd-Yb) bimetallic catalysts with different Pd/Yb ratios supported on carbon black (20%Pd-x%Yb/C, x?=?0, 1, 5, 10, and 15) were prepared by a sodium borohydride reduction method. The 20%Pd-5%Yb/C catalyst exhibited the best electrocatalytic activity towards methanol oxidation in alkaline media. The improved electrocatalytic activity and stability of 20%Pd-5%Yb/C can be explained by a bi-functional mechanism. In addition, the higher content of metallic palladium caused by the addition of ytterbium also contributes to the better catalytic activity of the 20%Pd+5%Yb/C catalyst. In view of the good electrocatalytic performance of 20%Pd+5%Yb/C, the 20%Pd+5%Yb catalyst supported on titanium suboxide (20%Pd+5%Yb/Ti₄O₇) was prepared. However, the Pd-Yb particles supported on Ti₄O₇ were seriously agglomerated. To improve the dispersion status of alloy particles, the Ti₄O₇ was functionalized with poly(diallyldimethylammonium chloride) (Ti₄O₇-PDDA). Electrochemical characterizations showed that no matter Ti₄O₇ or Ti₄O₇-PDDA as supports, Pd-Yb catalysts exhibited better catalytic activity than 20%Pd-5%Yb/C. The improvement mainly results from the further increase of metallic Pd due to the presence of Ti₄O₇.     

Enhanced photocatalytic performance of TiO2 particles via effect of anatase–rutile ratio

In the present work anatase–rutile transformation temperature and its effect on physical/chemical properties as well as photocatalytic activity of TiO₂ particles were investigated. The characterisation of the synthesised and annealed TiO₂ particles were determined by X-Ray Powder Diffraction (XRD), scanning electron microscope (SEM), dynamic light scattering (DLS) and Brunauer–Emmett–Teller surface area analysis (BET). The refraction in the ultraviolet–visible (UV–vis) range was assessed using a dual-beam spectrophotometer. The photocatalytic performance of the particles was tested on methylene blue solution. The XRD data indicated that the percentage of rutile increased with the annealing temperature and almost 100% of anatase transformed to rutile at 1000 °C. In addition, the phase transformation was a linear function of annealing temperature so phase composition of TiO₂ can be controlled by changing the annealing temperature. The SEM and BET results presented the increase of agglomerate size and the decrease of specific surface area with the increasing annealing temperature. This proved that anatase has smaller particle size and higher surface area than rutile. The photocatalytic activity of the annealed TiO₂ powders reduced with the increase of annealing temperature. The samples annealed at 900 °C and 925 °C with anatase: rutile ratio of 92:8 and 77:23, respectively, showed the best activity. These results suggested that the photocatalytic activity of TiO₂ particles is a function of phase composition. Thus it can be enhanced by changing its phase composition which can be controlled by annealing temperature.     

Influence of transition metals (Cr, Mn, Fe, Co and Ni) on the methane combustion over Pd/Ce-Zr/Al2O3 catalyst

The effects of transition metals (Cr, Mn, Fe, Co and Ni) on the catalytic properties of Pd/Ce-Zr/Al₂O₃ catalyst for methane combustion have been investigated. The supported Pd catalysts are characterized by BET, XRD, TEM, TPR, TPO and TPSR measurements. Activity tests in methane combustion show that Pd/Ce-Zr-Ni/Al₂O₃ has the highest catalytic activity and thermal stability among all catalysts. The results of TEM show that the addition of Ni to Pd/Ce-Zr/Al₂O₃ increases the dispersion of Pd component and inhibits the site growth. The results of TPO and TPSR show that the addition of Ni inhibits the decomposition of PdO particles and improves the reduction-reoxidation properties of the active PdO species, which increases the catalytic activity and thermal stability of the Pd/Ce-Zr/Al₂O₃ catalyst.     

Structural characteristics of mixed oxides MOx/SiO2 affecting photocatalytic decomposition of methylene blue

A series of photocatalysts based on silica (nanoparticulate) supported titania, ceria, and ceria/zirconia were synthesized and characterized by a variety of techniques including surface area measurements, X-ray diffraction, Fourier transform infrared spectroscopy, zeta potential, surface charge density, and photocatalytic behavior toward methylene blue decomposition. Thermal treatment at 600 °C increases the anatase content of the titania based catalysts detected by XRD. Changes in the infrared spectra before and after thermal treatment indicate that at low temperature there are more SiOTi bonds than at high temperature. As these bonds break upon heating the SiO₂ and TiO₂ separate, allowing the TiO₂ anatase phase to form. This results in an increased catalytic activity for the thermally treated samples. Nearly all titania based samples exhibit a negative surface charge density at pH 7 (initial pH of photocatalytic studies) which aids adsorption of methylene blue. The crystallinity of ceria and ceria/zirconia based catalysts are in some cases limited, and in others non-existent. Even though the energy band gap (E_g) can be lower for these catalysts than for the titania based catalysts, their photocatalytic properties are inferior.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Effect of Nb doping on morphology,crystal structure,optical band gap energy of TiO2 thin films

Nb–TiO₂ nanofibers and thin films were prepared using a sol–gel derived electrospinning and spin coating, respectively, by varying the Nb/Ti molar ratios from 0 to 0.59 to investigate the effect of Nb doping on morphology, crystal structure, and optical band gap energy of Nb–TiO₂. XRD results indicated that Nb–TiO₂ is composed of anatase and rutile phases as a function of Nb/Ti molar ratio. As the Nb/Ti molar ratio rose, the anatase to rutile phase transformation and the reduction in crystallite size occurred. The band gap energy of Nb–TiO₂ was changed from 3.25 eV to 2.87 eV when the anatase phase was transformed to rutile phase with increasing the Nb doping. Experimental results indicated that the Nb doping was mainly attributed to the morphology, the crystal structure, the optical band gap energy of Nb–TiO₂, and the photocatalytic degradation of methylene blue.     

Preparation, characterization and photocatalytic performance of TiO2/CexZr1−xO2 toward the oxidation of gaseous benzene

Increasing environmental pollution caused by the volatile organic compounds due to their toxicity makes their removal imperative. So it is crucial to develop processes which can degrade these compounds effectively. The paper demonstrates that the photocatalytic activity of TiO₂ toward the decomposition of gaseous benzene in a batch reactor can be greatly enhanced by loading TiO₂ onto the surface of Ce_xZr_1−xO₂ (x ≥ 0.25) using sol-gel technology. This research investigated the relationship between x amount and the photocatalytic activity of TiO₂. The prepared photocatalysts were characterized by BET, XRD, UV-vis diffuse reflectance and XPS analyses. The specific surface area of photocatalyst decreases as x decreases. XRD results reveal the no peaks of titania were detected. Among the five catalysts prepared, only the binding energy values of Ti2p_3/2 of TiO₂/Ce_0.5Zr_0.5O₂ shift toward lower value. The order of photocatalytic activity is TiO₂/Ce_0.5Zr_0.5O₂ > TiO₂/Ce_0.75Zr_0.25O₂ > TiO₂/CeO₂ ≈ TiO₂/Ce_0.25Zr_0.75O₂ > TiO₂/ZrO₂ ≈ TiO₂. The mechanism role of Ceria-Zirconia mixed oxides in photocatalytic reaction was speculated.     

Photocatalytic reduction of potassium chromate by Zn-doped TiO2/Ti film catalyst

The aim of this work was to investigate the photocatalytic (PC) reduction of potassium chromate by Zn-doped TiO₂/Ti film catalysts. The film catalyst was prepared by plasma electrolytic oxidation method in H₂SO₄ solution with different dosages of ZnSO₄. The composition and structure of the film catalysts was studied by XRD, SEM and EPMA. The removal rate of potassium chromate was investigated under the conditions of the different dosages of ZnSO₄ and the initial concentration of chromate potassium, and the reductive product during the PC reduction process was analyzed. The results showed that the film catalyst was composed of anatase TiO₂ and rutile TiO₂ with the porous structure. When the dosage of ZnSO₄ was 0.2 g/L, the film catalyst presented the highest catalytic activity, which related to the amount and the crystal grain size of anatase TiO₂ in the film. The PC reduction of potassium chromate by the film catalyst obeyed the pseudo-first-order kinetic equation. The UV-vis spectrum and XPS analyses proved that chromate Cr(VI) was reduced to Cr(III), which existed in the form of insoluble Cr(OH)₃.     

Optical properties of TiO2 anatase - Carbon nanotubes composites studied by cathodoluminescence spectroscopy

Luminescence spectra obtained by electron bombardment (cathodoluminescence, CL) on TiO₂ (anatase)/carbon nanotubes (CNT) composite, show only one visible band at 498 nm, while the spectra taken from pure anatase samples show two bands at 498 and 545 nm. We demonstrate that the visible luminescence bands are originated by TiO₂ surface defects due to oxygen vacancies, and that this luminescence signal is independent of TiO₂ mineral form (anatase or rutile). Moreover we obtain that the 545 nm band quenching in TiO₂/CNT composites is caused by empty oxygen vacancies (OV) related to oxygen given from oxygen-rich pristine powder of carbon nanotubes. Our conclusions are also supported by X-ray photoelectron spectroscopy (XPS), SEM analysis and energy dispersed X-ray measurements (EDX). Furthermore we can confirm that the NIR TiO₂ luminescence emission is linked only to the presence of Ti rutile form as described in several works in literature.     

Recovery properties of hydrogen gas sensor with Pd/titanate and Pt/titanate nanotubes photo-catalyst by UV radiation from catalytic poisoning of H2S

Recovery properties after H₂S catalytic poisoning of catalytic-type gas sensor with photo-catalysts and UV radiation have been examined. Each sensing material of the sensor consists of Pd, Pt supported on γ-Al₂O₃ and Pd/titanate, Pt/titanate nanotubes or TiO₂ particles. Pd/titanate and Pt/titanate nanotubes photo-catalyst were synthesized by hydrothermal synthesis method. All the sensors were deactivated after 500 ppm H₂S exposure for 20 h. The sensors with Pd/titanate or Pt/titanate nanotubes showed regenerated voltage response under UV radiation. However the sensor with TiO₂ particles showed negligible regenerated voltage response. Regenerated voltage response with Pd/titanate or Pt/titanate nanotubes may stem from location of Pd or Pt catalyst on the titanate nanotube photo-catalyst.     

Interfacial properties of Ce<Subscript>0.75</Subscript>Zr<Subscript>0.25</Subscript>O<Subscript>2</Subscript> supported noble metals (Pd,Pt) from first principles

First-principles electronic structure calculations of noble metals (NM=Pd, Pt)/Ce_0.75Zr_0.25O₂ systems are presented. It is found that: the NM adatoms do not prefer to stay at the atop or the bridge sites of the cations (Ce and Zr), but prefer to be adsorbed at or around the anion sites. The most preferable adsorption sites for both the Pd and Pt adatoms are the O-bridge sites neighboring the Zr dopant. The Pt adatom show much stronger interaction with the Ce_0.75Zr_0.25O₂(111) surface than does the Pd adatom. The interactions of the NM/Ce_0.75Zr_0.25O₂(111) interfaces are stronger than those of the corresponding NM/ceria(111) interfaces. There are some metal induced gap states (MIGS) appeared in the gaps of the NM/Ce_0.75Zr_0.25O₂(111) interfaces, which are important to catalytic properties of the NM/Ce_0.75Zr_0.25O₂(111) catalysts.     

Photocatalytic activity of multielement doped TiO2 in the degradation of congo red

TiO₂ although considered a promising photocatalyst for the degradation of aqueous pollutants, it suffers from poor absorption in the visible region and hence requires ultraviolet (UV) light for activation. To make TiO₂ a visible active photocatalyst, multielement (C, N, B, and F) doping has been done. The synthesised CNBF/TiO₂ catalysts were calcined at different temperatures and characterized by XRD, BET surface area, UV DRS, XPS, HRSEM-EDAX, and TEM techniques. These catalysts found to show less band gap values when compared to bare TiO₂. These catalysts were tested for their catalytic activity towards the degradation of a textile dye - congo red (CR) under different reaction conditions. It was found that the photocatalytic activity was dependent on both doping of multielement and the calcination temperature of CNBF/TiO₂. The co-doped catalysts which were calcined at 400 °C and 600 °C (100% intensity in anatase phase) were found to be the best catalysts (100% decolourisation of CR in 21/2 h and 2 h respectively). TOC analysis carried out for the samples at the reaction time of 5 h showed very high percentage (83%) degradation of CR over CNBF/TiO₂ catalysts calcined at 600 °C when compared to the other catalysts calcined at different temperatures. CNBF/TiO₂ (1000 °C) showed very less photocatalytic activity due to the formation of rutile phase.