Preparation and characterization of gadolinium hydroxide single-crystalline nanorods by a hydrothermal process

The Gd(OH)3 nanorods with diameters of ca.40-60 nm and lengths of more than 400-550 nm have been prepared by a novelhydrothermal technique.The structural features and chemical composition of the nanorods were investigated by X-ray diffraction(XRD),transmission electron microscopy(TEM),and field emission scanning electron microscope(FESEM),selected areaelectron diffraction(SAED),and high resolution transmission electron microscopy(HRTEM).The possible mechanism for theformation of Gd(OH)3 nanorods was proposed.     

Characterization of h-WO3 nanorods synthesized by hydrothermal process

Hexagonal tungsten oxide nanorods have been synthesized by hydrothermal strategy using Na₂WO₄·2H₂O as tungsten source, aniline and sulfate sodium as structure-directing templates. Techniques X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy have been used to characterize the structure, morphology and composition of the nanorods. The h-WO₃ nanorods are up to 5 μm in length, and 50–70 nm in diameter.     

WS2纳米棒的合成及其摩擦学性能

以十六烷基三甲基溴化铵(CTAB)作为表面活性剂,利用水热合成法在180℃条件下成功制备出WS2纳米棒。用XRD、SEM、TEM和HRTEM对WS2纳米棒的结构进行表征和分析,并提出了可能的生长机理。将WS2作为润滑油添加剂加到基础油中,用CETR UMT-2摩擦磨损仪测试其摩擦学性能。结果表明:WS2纳米棒作为润滑油添加剂表现出良好的摩擦性能。     

MnOOH纳米棒的反胶束法制备及表征

采用水溶液/CTAB/正丁醇/庚烷四组分组成的反相胶束体系,制备了MnOOH纳米棒,并用透射电镜(TEM)、高分辨透射电镜(HRTEM)和X射线粉末衍射(XRD)进行了表征.结果显示所得MnOOH为单斜晶系,直径约为10 nm、长度约为200 nm.实验表明,不同的反应时间所得纳米棒的长度不同,但直径可以保持不变.     

Selected-control synthesis of PbO2 and Pb3O4 single-crystalline nanorods

Reaction of Pb(OH)3- with ClO- in the presence of surfactant CTAB under conventional conditions resulted in PbO2 nanorods, whereas the reaction under hydrothermal conditions afforded Pb3O4 nanorods, as confirmed by X-ray powder diffraction and transmission electron microscopy (TEM). Selected area electron diffraction (SEAD) and high-resolution TEM (HRTEM) revealed that both PbO2 and Pb3O4 nanorods are single crystalline. For the formation of Pb3O4 nanorods, it is reasonable that PbO2 slowly decomposes to Pb3O4 under hydrothermal conditions, while retaining the morphology of PbO2.     

NaOH溶液中CdS纳米棒的水热合成

在NaOH溶液中水热合成了CdS纳米棒, 并探讨了NaOH溶液浓度和反应时间对CdS纳米棒形貌及晶体结构的影响及其可能的生长机理和母液循环可行性. 用粉末X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 高分辨透射电子显微镜(HRTEM)和选区电子衍射(SAED)对CdS纳米棒进行了表征, 并考察了其在可见光照射下光催化降解亚甲基蓝的活性. 结果表明, NaOH溶液是形成棒状形貌的关键因素. 在最优实验条件下, 可获得六方纤锌矿结构CdS纳米棒, 直径约200 nm, 长度可达4 μm. 该纳米棒具有良好的可见光光催化活性.     

Ultralong cadmium hydroxide nanowires: synthesis, characterization, and transformation into CdO nanostrands

Ultralong Cd(OH)2 nanowires were fabricated by a hydrothermal method from Cd(CH3COO)2 x H2O (0.01 mol/L) and C6H12N4 (0.015 mol/L) aqueous solution at 95 degrees C for 16 h without using any templates and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and high-resolution transmission electron microscopy (HRTEM). The length of the nanowires reached several micrometers, giving an aspect ratio of a few thousands. The formation mechanism of the nanowires is attributed to the oriented attachment of small particles. The growth method for the 1D nanostructure presented here offers an excellent tool for the design of other advanced materials with anisotropic properties. The Cd(OH)2 nanowires efficiently captured negatively charged dye, and the adsorbed dye molecules can be released after the addition of EDTA. The Cd(OH)2 nanowires as template compounds were further transformed into CdO semiconductor nanomaterials with similar morphology by calcination under 350 degrees C in air for 3 h.     

海藻酸锌纤维热降解法制备氧化锌纳米结构

采用天然高分子海藻酸钠为原料, 以氯化锌水溶液为凝固浴, 通过湿法纺丝技术成功制备了海藻酸锌(Alg-Zn)纤维.通过在空气中不同温度下对所得海藻酸锌纤维进行热处理, 得到了多种ZnO纳米结构. 利用热失重分析(TG)、X射线衍射(XRD)、电子能量损失谱(EELS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物的组成、形貌和微观结构进行了详细表征. 结果表明, 焙烧温度和时间对所得ZnO纳米结构的尺寸和形貌具有重要影响; 800 ℃下热处理24 h以上可以得到直径约为120 nm的ZnO纳米棒. 通过仔细考察不同热处理时间得到的ZnO纳米结构, 提出了在焙烧条件下ZnO纳米棒的生长机理.     

嵌埋式纳米钌基催化剂的制备及其催化水煤气变换反应的性能

 采用溶胶法制备了平均粒径为4.9 nm的RuO2溶胶,然后以镁铝尖晶石为载体,用一步沉淀法制备了嵌埋式纳米Ru基水煤气变换反应催化剂. 利用透射电子显微镜、扫描电子显微镜和粉末X射线衍射等技术对样品进行了表征. 结果表明, Ru纳米粒子均匀分散在载体内部,催化反应活性中心通过载体上形成的细微孔道与反应物接触. 向催化剂中添加适量的K2O和La2O3助剂可以有效地提高其催化活性.     

α-Fe2O3表面结构对NH3选择性催化还原NO活性的影响

通过水热法合成了两种具有不同形貌的α-Fe2O3纳米棒和纳米立方体,并探索了它们的中温NH3选择性催化还原(NH3-SCR)NO的活性.NH3-SCR测试表明α-Fe2O3纳米棒具有更高的催化活性.X射线粉末衍射(XRD)、场发射扫描电镜(FE-SEM)和高分辨透射电镜(HRTEM)结构分析表明:α-Fe2O3纳米棒暴露有高表面能的{110}活性面,而纳米立方体暴露的主要是低表面能的{012}晶面.H2程序升温还原(H2-TPR)和NO程序升温脱附(NO-TPD)结果证明纳米棒比纳米立方体具有更高的氧化还原性能.因此,α-Fe2O3纳米棒由于暴露高表面能的活性面具有比纳米立方体更高的NH3-SCR性能.     

尺寸可控氢氧化镧纳米棒的水热合成及表征

以硝酸镧为镧源、三乙胺为碱源和络合剂,通过简便的水热法成功合成了大量均一的氢氧化镧纳米棒。详细研究了三乙胺的用量、表面活性剂、反应温度和时间对产物形貌及尺寸的影响。基于实验结果,提出了氢氧化镧纳米棒的形成机理。同时制备了稀土掺杂的氢氧化镧纳米棒。利用X射线衍射（XRD）、透射电子显微镜（TEM）、选区电子衍射（SAED）和高分辨透射电子显微镜（HRTEM）对所得产物的物相、结构和形貌进行了表征分析。     

以CuC2O4微球为模板可控合成一维CuC2O4/ZnO异质结构

以CuC2O4纳米微球为模板,通过水热法在120 ℃、1 h时成功合成了一维CuC2O4/ZnO异质结构。 采用热重分析（TGA）、场发射扫描电子显微镜（FE-SEM）、能量散射Ｘ射线谱（EDX）、透射电子显微镜(TEM)和Ｘ射线粉末衍射(XRD)等测试技术对产物的结构和形貌进行了表征。 结果表明,所得产物为一维CuC2O4/ZnO纳米棒束,长约1 μｍ,直径约500 nm。 每个棒束由许多纳米棒沿同一方向组装而成。 TEM照片和EDX光谱表明,CuC2O4和ZnO形成了均匀的异质结构。     

从Mn3O4前驱体到MnO2纳米结构的形貌和结构变化

锰氧化物是一类重要的且具有广泛应用背景的材料, 控制合成不同形貌和组成的锰氧化物纳米结构将有助于拓宽其应用领域. 本文报道了以Mn3O4为前驱体, 通过水热法控制合成MnO2纳米结构的方法. 用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)等手段对产物进行表征. 在硫酸体系中,当反应温度为80 和180 ℃时, 所得产物分别为γ-MnO2海胆结构和β-MnO2单晶纳米棒. 此外, MnOOH纳米线可以在稀酸溶液中合成. 考察了反应温度、溶液酸度、反应时间对产物结构的影响, 并提出了基于γ-MnO2为中间产物的反应机理. 实验结果表明, 水热体系促进了产物的各向异性生长并最终形成不同形貌和结构的锰氧化物.     

Synthesis of copper-core/carbon-sheath nanocables by a surfactant-assisted hydrothermal reduction/carbonization process

A simple hydrothermal method has been developed for the one-step synthesis of copper-core/carbon-sheath nanocables in solution. The obtained nanostructures were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and high-resolution TEM (HRTEM), Raman, and UV-vis spectrum analysis. These copper@carbon nanocables formed through the hydrothermal reduction/carbonization in the presence of surfactant cetyltrimethylammonium bromide (CTAB) acting as the structure-directing agent by hydrothermal treatment. HRTEM and selected-area electron diffraction (SAED) indicate that the resulted Cu nanowires had the preferred [110] growth direction. The influence of the reaction temperature, reaction time, and pH on the final products was investigated in detail. The possible formation mechanism for copper-core/carbon-sheath nanocables was also proposed. Amorphous carbon nanotubes can be obtained by etching the copper core in the nanocables.     

Co掺杂ZnO纳米棒的水热法制备及其光致发光性能

以Zn(NO3)2·6H2O 和Co(NO3)2·6H2O为原料, 通过水热法在较低温度下制备了纯ZnO和Co掺杂的ZnO(ZnO:Co)纳米棒. 利用XRD、EDS、TEM和HRTEM对样品进行了表征, 结合光致发光(PL)谱研究了样品的PL性能. 结果表明, 水热法制备纯ZnO和ZnO:Co纳米棒均具有较好的结晶度. Co2+是以替代的形式进入ZnO晶格, 掺入量为2%(原子分数)左右. 纯的ZnO纳米棒平均直径约为20 nm, 平均长度约为180 nm; 掺杂样品的平均直径值约为15 nm, 平均长度约为200 nm左右; Co掺杂轻微地影响ZnO纳米棒的生长. 另外, Co掺杂能够调整ZnO纳米棒的能带结构、提高表面态含量, 进而使得ZnO:Co纳米棒的紫外发光峰位红移, 可见光发光能力增强.     

PbS纳米棒的水热合成与表征

以乙酸铅和硫脲为主要原料,十二烷基磺酸钠和十六烷基三甲基溴化铵为表面活性剂,在120℃反应12h,水热法制备了PbS纳米棒.并利用X射线粉末衍射(XRD)、透射电子显微镜(TEM)和高分辨电子显微镜(HRTEM)等手段对产物进行了表征,实验结果表明：产物为纯相立方结构的PbS单晶纳米棒.考察了乙酸铅和硫脲间的摩尔比以及反应温度对合成产物的影响,并初步探讨其形成机理.     

锂离子电池正极材料LiMn2O4的合成与晶体结构（英）

Spinel LiMn₂O₄ powders were prepared using two-step synthesis method consisting of solid-state reaction method and citrate modified sol-gel method. The effects of the calcination temperature and the Li/Mn ratio of raw materials were studied on the physicochemical and electrochemical properties of the spinel LiMn₂O₄ powders, such as crystallinity, lattice constant and density. The title compound was characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Polycrystalline LiMn₂O₄ powers calcined at 750 ℃ were found to be composed of very uniformly-sized microcrystal with an average particle size of 300 nm. The improvement in electrochemical properties was mainly attributed to the process of re-grinding by absolute alcohol.     

一种在固体基底上制备高度取向氧化锌纳米棒的新方法

采用廉价、低温的方法，在修饰过ZnO纳米粒子膜的ITO基底上成功制备出具有 高长径比、高度取向的ZnO纳米棒阵列，用扫描电子显微镜(SEM)，X射线衍射(XRD) ，高分辨透射电子显微镜(HRTEM)以及拉曼光谱对制备出的ZnO纳米棒的结构和形貌 进行了表征，测试结果表明，ZnO纳米棒是单晶，属于六方晶系，与基底直，上仍 沿(001)晶面择优生长的特征，并且ZnO纳米棒基本上无氧空位的存在，统计结果显 示，水热反应2h后90%以上的ZnO纳米棒直径为120～190nm，长度为4μm     

葡萄糖辅助合成碲化铅纳米棒及其表征

采用简单的葡萄糖辅助溶剂热合成法制备了碲化铅纳米棒。 利用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、高分辨率透射电子显微镜(HRTEM)、能谱仪(EDS)等技术手段进行材料结构和形貌表征。 结果表明,产物是纯的立方相PbTe,纳米棒的直径约为50 nm,长500 nm左右。 研究了反应过程的影响因素及碲化铅纳米棒的形成机制。 产物的形貌受葡萄糖的量、反应时间、反应温度和聚乙烯吡咯烷酮(PVP)质量的控制,分析了形成这种结构的原因。     

Formation of MoS2 inorganic fullerenes (IFs) by the reaction of MoO3 nanobelts and S

The reaction of MoO3 and S at temperatures higher than 300 degrees C in an argon atmosphere provides a convenient and effective method for the synthesis of MoS2 nanocrystalline substances. MoS2 nanotubes and fullerene-like nanoparticles have been obtained by the reaction at 850 degrees C under well-controlled conditions. The influences of reaction temperature and duration were carefully investigated in this paper. All of the nanostructures were characterized by Xray powder diffraction (XRD), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). A stepwise reaction model and rolling mechanism were proposed based on the experimental results.