亚稳态MInS2(M=Ag,Cu)花状微米球的热分解法合成及其生长机理

采用热分解法制备了三维的亚稳态正交相AgInS_2和六方相CuInS_2花状微米球。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)等对样品进行表征,对AgInS_2的光催化性能进行了评估,并借助于热重-差热分析(TG-DTA)等手段研究了亚稳态正交相AgInS_2和六方相CuInS_2花状微米球的生长机理。实验结果表明,反应温度和反应物中金属离子的投料比对生成纯相的MIn S2均有影响,而AgInS_2花状微米球能在可见光下较好地催化降解亚甲基蓝。     

三维花状Fe2（MoO4）3微米球的水热制备及电化学性能

以FeCl₃·7H₂O和Na₂MoO₄为原料,采用水热合成法制备三维花状Fe₂（MoO₄）₃微米球。探讨不同合成温度对样品形貌的影响,利用XRD、SEM和EDS等分析技术对样品的结构、形貌进行了表征,对该材料的电化学性能进行了测试。结果表明：Fe₂（MoO₄）₃微米球是由二维纳米片自组装而成的花状结构,合成温度为160℃时,制备的样品具有良好的电化学性能,当电流密度为100mA·g^-1,首次放电比容量为1431mAh·g^-1;并具有较好的循环性能和倍率性能。并对160℃合成样品表现较好电化学性能的原因进行了探讨。     

共沉淀法制备六方相ITO纳米粉体及其光电性能

以金属In、SnCl₄5H₂O为原料、尿素为沉淀剂,采用共沉淀法加入（NH₄）₂SO₄,制备出六方相ITO纳米粉体。通过XRD、TEM、四探针电阻仪、荧光光谱仪以及XPS,研究了ITO粉体的晶型、颗粒形貌、电性能以及光性能。结果表明：加入（NH₄）₂SO₄后,ITO粉体形貌由类菱面体和类球形混合体转变为类球形;不加（NH₄）₂SO₄时晶型为立方相结构,当（NH₄）₂SO₄与铟的物质的量之比为1：3.45和1：1.73时粉体晶型转变为六方相结构,继续添加（NH₄）₂SO₄晶型又转变为立方相结构。立方相ITO粉体的电阻率较低为0.64 Ωcm,六方相ITO粉体在相同激发波长下,发射光强度相对较高。     

CuInS2量子点敏化太阳能电池中尺寸依赖的电子注入和光电性质

研究了CuInS₂（CIS）量子点敏化太阳能电池（QDSSCs）的电子注入和器件性能与粒子尺寸之间的依赖关系. 首先合成了不同尺寸的CuInS₂量子点（QDs）,制备了CuInS₂量子点敏化的TiO₂薄膜,并组装了量子点敏化太阳能电池. 通过循环伏安法确定了CuInS₂量子点的能级位置. 采用时间分辨荧光光谱分析测量了CuInS₂量子点到TiO₂薄膜的电子转移速率和效率. 结果发现,随着粒子尺寸从4.0 nm减小到2.5 nm,电子注入速率略微增加而电子注入效率减小,同时量子点敏化太阳能电池的开路电压基本不变,而光电转换效率、短路电流和填充因子（FF）均减小. 上述研究结果表明量子点敏化太阳能电池性能的优化可以通过改变量子点的尺寸来实现.     

自组装α-Fe2O3亚微米球的制备及其光催化性质

在乙二醇体系中, 通过简单的二步方法成功合成了α-Fe₂O₃亚微米球。第一步,以Fe(NO)₃和C₆H₁₂N₄为主要反应物160 ℃溶剂热反应8h制备出前驱体;第二步,煅烧前驱体成功合成了斜方相的α-Fe₂O₃产物。利用X射线粉末衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM),红外吸收光谱(FTIR),能谱分析(EDS)和热重分析(TGA)等手段对产物进行了表征。在300 W紫外灯(主波长为365 nm)照射下降解一定浓度的甲基橙溶液,研究不同光催化剂对甲基橙溶液降解效果。由于制备产物的形貌和粒径影响其比表面积和对反应物的吸附能力以及带隙能,使得制备产物具有良好的光催化性能。结果表明,α-Fe₂O₃亚微米球在紫外光照射条件下对甲基橙溶液有光降解作用。     

TiO2纳米微球的制备及在染料敏化太阳能电池中的应用

以四氯化钛、盐酸为原料,制备出花状TiO₂纳米微球,利用扫描电子显微镜（SEM）、X射线衍射（XRD）等测试方法,对样品的结构和形貌进行了表征。为了提高TiO₂微球电池的光电性能,利用TiO₂微球作为反射层构造了双层结构的薄膜电极,结果表明,双层结构染料敏化太阳能电池在100 mW·cm^-2（1.5 G）光照条件下,短路光电流J_sc为17.64 mA·cm^-2,开路光电压Voc为0.74 V,填充因子FF为0.63和光电转化效率η为8.33%。相比TiO₂微球制备的太阳能电池,双层结构染料敏化太阳能电池光电转化效率提高至5.3倍。最后对电极中染料的吸附量、电极的光散射性能和电池的电化学阻抗做了进一步研究和分析,研究表明,双层结构电池增强光的捕获能力,从而提高光伏性能。     

水热法合成由纳米棒自组装而成的TiO2微米球

一定条件下, 用水热法以0.15 mol/L的TiCl₃饱和NaCl水溶液在玻璃基板上制备了TiO₂微米球, SEM, TEM和XRD表征结果说明, 生成的TiO₂晶体为金红石型, TiO₂微米球由TiO₂纳米棒大规模自组装而成. 研究了添加剂尿素的含量、反应温度、反应时间和TiCl₃起始浓度对产物的影响, 探索出了制备TiO₂微米球的最优条件, 并讨论了反应机理.     

油溶性CuInS2/ZnS量子点的制备及其温敏性聚丙烯酰胺胶束介导的水相转移

采用非热注法成功制备了高质量的油溶性CuInS₂/ZnS核壳量子点, 量子点的荧光发射峰在可见光到近红外范围内可调(550~800 nm), 且荧光量子产率最高达80%。本文进一步利用具有温敏特性的聚丙烯酰胺胶束作相转移剂, 成功地将油溶性的CuInS₂/ZnS核壳量子点转移入水相。水相中自组装形成的CuInS₂/ZnS量子点-胶束复合物不仅具有良好的荧光性质, 而且胶束原有的灵敏的热响应性被保留。这些研究初步表明, 无镉的低毒的CuInS₂/ZnS量子点可作为纳米胶束的荧光示踪探针。     

Ag2CO3/BiVO4复合微米片光催化剂的制备、表征及光催化机理

采用水热法制备粒径为1~2 μm的BiVO₄微米片,然后在微米片表面沉积不同含量的Ag₂CO₃颗粒,制备Ag₂CO₃/BiVO₄复合微米片光催化剂。利用X射线粉末衍射（XRD）、扫描电镜（SEM）、红外光谱（FTIR）、紫外-可见漫反射光谱（UV-Vis DRS）、光致发光（PL）光谱、瞬态光电流-时间响应对催化剂进行表征。以可见光为光源,罗丹明B为降解对象进行光催化活性测试。结果表明,复合适量Ag₂CO₃有利于提高光催化剂的比表面积,改善催化剂的表面性能。活性测试结果表明,当复合10%（w/w）Ag₂CO₃时,Ag₂CO₃/BiVO₄光催化活性最佳,比纯BiVO₄提高4.4倍。光致发光（PL）光谱、瞬态光电流-时间响应测试结果表明,复合Ag₂CO₃能有效抑制光生电子与空穴的复合。自由基捕获实验结果表明,该体系的活性氧物质为空穴和羟基自由基。Ag₂CO₃/BiVO₄复合光催化剂活性提高的原因,是较宽带隙的Ag₂CO₃与较窄带隙的BiVO₄形成的异质结有效抑制了光生电子与空穴的复合,同时两者适宜的能带结构保证产生更多的空穴,从而具有更强的氧化能力。     

离子层气相反应法(ILGAR)制备CuInS2薄膜的研究

CuInS₂ thin films have been prepared by ion layer gas reaction (ILGAR) using C₂H₅OH as solvent, CuCl and InCl₃ as reagents and H₂S gas as sulfuration source. The effects of cationic concentrations and numbers of cycle on the properties of CuInS₂ film were investigated. The chemical composition, crystalline structure, surface topography, deposited rate, optical and electronic properties of the films were characterized by X-ray diffractrometry (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), ultraviolet-visible spectrometry (UV-Vis) and Hall System. The results show that the crystalline of CuInS₂ thin films and the deposition rate have been improved with the increase of cationic concentration, while CuxS segregation phases appear with further increasing cationic concentration. The deposition rate is close to constant as cationic concentration is fixed. CuInS₂ thin film derived form lower cationic concentration is uniform, compact and good in adhesion to the substrates. The absorption coefficient of CuInS₂ thin films is larger than 10⁴ cm^-1, and the band gap E_g is in the range of 1.30～1.40 eV. The dark resisitivity of the thin film decreases from 50 to 10 Ω·cm and the carrier concentration ranges are over 10¹⁶ cm^-3.     

AgInS2纳米粒子的制备及其可见光催化活性

以水为溶剂,硫代乙酰胺为硫源,巯基乙酸为包覆剂,于低温下制备了正交相的AgInS2纳米粒子。用TEM、EDS和XRD对所制备的AgInS2纳米粒子的形貌、组成和晶相进行了表征。并考察了反应时间对AgInS2纳米粒子的晶相及其可见光催化降解活性的影响。结果表明:延长反应时间可以提高AgInS2纳米粒子的结晶性和可见光催化活性。     

Growth of CuInS2 Nanotubes from Cu2S-CuInS2 Heterostructures as a Potential Photovoltaic Material

Chemically synthesized nanostructures possess well-defined domains with an interconnected network, which helps the carriers to bypass the other material in the solar cell while moving to their respective electrodes. In this work, CuInS₂ films constituting CuInS₂ nanotubes and nanoparticles were fabricated using a hot-injection chemical technique, followed by sulfurization. Structural and microstructural investigations reveal Cu₂S nanoparticle formation at an early stage of growth of nanotubes, serving as possible catalyst sites for the subsequent anisotropic growth of the heterostructured hexagons. The crossover takes place over a number of intermediate stages. This sharing of the heterostructure by the hexagonal Cu₂S and chalcopyrite CuInS₂ minimizes the lattice distortion. The Cu₂S- CuInS₂ interface in the heterostructure acts as the nucleation center for CuInS₂ nanotubes. Optical absorption and Raman spectroscopy studies reveal better optical properties for CuInS₂ nanoparticles as compared to CuInS₂ nanotubes. Compared to all other nanostructures, nanowires or nanotubes tend to provide single-crystalline nanograins for direct characterization. These nanoparticles, especially the nanotubes, can be used to form an interconnected network structure of p- and n-type materials in bulk heterojunctions providing the key to improve solar cell efficiencies.     

Synthesis of CuInS2@CdS Core‐Shell Nanocrystals

CuInS₂@CdS core‐shell nanocrystals were prepared in a wet chemical process. Transmission electron microscope (TEM), x‐ray energy dispersive spectroscopy (EDAX), x‐ray diffraction (XRD), absorption, and photoluminescence (PL) spectra were used to confirm the formation of the CuInS₂@CdS core‐shell structure. The growth of CdS shell not only increased the PL intensity, but also restrained the transformation of CuInS₂ from nanoparticles to nanorods after annealing, which was attributed to an effective chemical passivation of the CuInS₂ core by the CdS shell.     

Synthesis of CuInS2 Nanocubes by a Wet Chemical Process

Cube‐shaped CuInS₂ nanoparticles were successfully prepared through a simple low‐temperature solution route. Mercaptoacetic acid was used as capping agent. The product was characterized by means of X‐ray diffraction (XRD), energy dispersive analysis of X‐rays (EDAX), transmission electron microscopy (TEM), and photoluminescence spectroscopy (PL). The CuInS₂ nanocubes obtained were of a chalcopyrite structure. The EDAX analysis shows that as‐synthesized CuInS₂ nanocubes were slightly Cu‐rich and nearly stoichiometric.     

TiO2 nanoparticles incorporated with CuInS2 clusters: preparation and photocatalytic activity for degradation of 4-nitrophenol

TiO₂ nanoparticles incorporated with CuInS₂ clusters were prepared in a solvothermal process and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersion X-ray analysis (EDX). Compared with pure TiO₂ nanoparticles, the TiO₂ nanoparticles incorporated with CuInS₂ clusters display higher photocatalytic activity with 99.9% of degradation ratio of 4-nitrophenol after 2 h irradiation. In order to investigate the effect of the CuInS₂ clusters on the photocatalytic activity of TiO₂ nanoparticles, diffuse reflectance UV–Vis spectra (DRS), photoluminescence (PL) spectra, and photocurrent action spectra were measured. The results indicate that the enhanced photocatalytic activity is probably due to the interface between TiO₂ and CuInS₂ as a trap of the photogenerated electrons to decrease the recombination of electrons and holes.     

SILAR法制备化学计量CuInS2薄膜

在室温下，以不同c_Cu/c_In的CuCl₂和InCl₃混合溶液作为阳离子前驱体，Na₂S水溶液为硫源，利用连续离子层吸附反应法(SILAR)在玻璃基底上制备了CuInS₂薄膜。XRD结果表明，当c_Cu²⁺/c_In³⁺在1～1.5范围内均可形成具有黄铜矿结构的CuInS₂薄膜。SEM观察到随c_Cu²⁺/c_In³⁺的升高，薄膜表面颗粒长大并出现团簇聚集。通过XPS测定薄膜表面的化学组成证明当c_Cu²⁺/c_In³⁺=1.25时，CuInS₂薄膜接近其标准的化学计量组成。此时薄膜的吸收系数大于>10⁴ cm^-1，禁带宽度E_g为1.45 eV。     

Formation of Rod-Like CuInS2 Nanocrystals on the Glass Substrate

Rod-like CuInS₂ nanocrystals on the glass substrate were prepared by annealing the coat of CuInS₂ nanoparticles. The products were characterized by means of energy dispersive analysis of x-ray (EDAX), x-ray diffraction (XRD) and scanning electron microscopy (SEM). The results of XRD and EDAX show that the rod-like CuInS₂ nanocrystals obtained are of a chalcopyrite structure and are nearly stoichiometric. The aggregation mechanism of “oriented attachment” of nanocrystals is believed to be operative and compatible in this study.     

Alloyed (ZnS)x(CuInS2)1−x Semiconductor Nanorods: Synthesis,Bandgap Tuning and Photocatalytic Properties

Rod-like nanocrystals of the semiconductor alloy (ZnS)_x(CuInS₂)_1−x (ZCIS) have been colloidally prepared by using a one-pot non-injection-based synthetic strategy. The ZCIS nanorods crystallize in the hexagonal wurtzite structure and display preferential growth in the direction of the c axis. The bandgap of these quarternary alloyed nanorods can be conveniently tuned by varying the ratio of ZnS to CuInS₂. A non-linear relationship between the bandgap and the alloy composition is observed. The ZCIS nanorods are found to exhibit promising photocatalytic behaviour in visible-light-driven degradation of Rhodamine B.