共查询到18条相似文献,搜索用时 375 毫秒
1.
以正硅酸乙酯为前驱体,采用无溶剂水解技术,制备出了均一、稳定、透明的SiO_2溶胶,通过透射电子显微镜分析,粒径在100 nm左右;在溶胶中加入甲基丙烯酸甲酯(MMA)和偶氮二异丁腈(AIBN),采用热固化制备了透明的块体PMMA/SiO_2杂化材料,通过差热(DSC)和热重分析(TGA)研究了杂化材料的热性能. DSC结果表明,当体系中的SiO_2质量分数超过20%时,杂化材料无明显的玻璃化转变现象. TGA结果表明,杂化材料的分解温度提高约110 ℃. 透射电子显微镜观察结果表明,无机相均匀分散在有机相中,两相之间没有明显的相分离现象. 相似文献
2.
PDMS/SiO2 杂化材料的制备与性能研究 总被引:1,自引:0,他引:1
以羟基封端的聚二甲基硅氧烷(PDMS)和正硅酸乙酯为主要原料,通过溶胶-凝胶法成功制备出均匀透明的PDMS/SiO2杂化材料,采用红外吸收光谱、紫外-可见光透过光谱、扫描电子显微镜以及热分析仪对制备的材料进行了表征。结果表明,所制得的杂化材料以化学键相结合,两相分散均匀,可见光区透光率高达90%以上,耐热性能良好。 相似文献
3.
4.
采用溶胶凝胶-原位聚合法以正硅酸乙酯(TEOS)为硅源、乙烯基三乙氧基硅烷(VTEOS)为偶联剂制备了活性SiO2溶胶,经水解、缩合,再于引发剂AIBN作用下与丙烯酸进行原位聚合杂化,制得聚丙烯酸/SiO2杂化溶胶,陈化后用拉丝法制得聚丙烯酸/SiO2杂化纤维。研究了溶胶的杂化机理、成纤性能;采用红外光谱、扫描电子显微镜分析了杂化纤维的结构和微观形态;进行了杂化纤维的TGA和耐水性能测试。结果表明,该聚丙烯酸/SiO2杂化溶胶拉丝性能好,可拉丝时间达1h,杂化溶胶在粘度为1400~3000mPa.s时成纤性能好,可通过拉丝法制得形态良好的杂化纤维;聚丙烯酸与SiO2之间通过化学键作用,在纤维内部有机无机两相间形成均一的连续相;聚丙烯酸/SiO2杂化纤维的耐热和耐水性能均优于纯PAA。 相似文献
5.
6.
7.
聚酰亚胺-二氧化硅杂化膜的制备及表征 总被引:21,自引:0,他引:21
采用溶胶-凝胶法制备了两类具有不同二氧化硅含量的聚酰亚胺-二氧化硅(PI-SiO2)杂化膜,并用SEM,IR,TG-DTA,氮吸附和气体渗透性能测试等手段对该膜材料的表面形貌、结构、热性能、孔径分布和气体渗透性能进行了表征.结果表明,PI-SiO2膜材料中SiO2粒子的分散良好,与有机相之间存在着分相和键联;膜材料的玻璃化温度θg均随SiO2含量的增加而升高.相比之下,在酸性条件下制备的T系列杂化膜比在碱性条件下合成的S系列杂化膜对θg的影响更大一些;杂化膜具有较好的气体渗透性能和亲水性能,其H2O/N2和H2O/CH4的分离系数远大于努森扩散的理论值. 相似文献
8.
9.
聚醚型氨酯酰亚胺/二氧化硅杂化材料的合成与性能研究 总被引:4,自引:0,他引:4
利用Sol Gel共聚合反应制备出聚醚型氨酯酰亚胺 (PUI) /二氧化硅 (SiO2 )杂化材料 .利用NMR、FTIR、TG、DSC及SEM等测试手段对性能进行了基本表征 .FTIR研究结果发现在 10 0℃下能同时完成有机相PUI的亚胺化和无机相SiO2 凝胶网络的Sol Gel转变 .TG及SEM发现SiO2 含量为 9wt%时SiO2 聚集相粒径在 0 2~1 0 μm之间 ,耐热性明显提高并达到最佳 ;发现SiO2 含量的增加其颗粒粒径不断增大 ,并不断聚集成大粒径SiO2 相 ,有机和无机相分离明显 .DSC研究显示 ,SiO2 相的引入 ,对杂化材料聚醚软段富集相的Tg 不产生明显影响 . 相似文献
10.
11.
Polymerization of w/o microemulsions for the preparation of transparent SiO2/PMMA nanocomposites 总被引:1,自引:0,他引:1
Palkovits R Althues H Rumplecker A Tesche B Dreier A Holle U Fink G Cheng CH Shantz DF Kaskel S 《Langmuir : the ACS journal of surfaces and colloids》2005,21(13):6048-6053
Reverse w/o microemulsions composed of methyl methacrylate (MMA) forming the oil phase, nonionic surfactants, and water are used for the synthesis of transparent SiO2/PMMA nanocomposites. An inorganic precursor, tetraethoxysilane (Si(OEt)(4), TEOS), is hydrolyzed in the reverse micelles containing aqueous ammonia. During the hydrolysis of TEOS, polymerization of the continuous MMA phase is initiated using AIBN (azobisisobutyronitrile), and after thermal polymerization at 333 K for 12 h, solid blocks of PMMA are obtained in which nanometer-sized silica particles are trapped in the solid polymer matrix. According to small-angle X-ray and dynamic light scattering experiments, the water droplets in MMA microemulsions are 12 nm (R(W) = 13) in diameter, whereas after polymerization of the microemulsion, the SiO2 particles in the transparent SiO2/PMMA composites are 26 nm in diameter. Transmission electron micrographs demonstrate a low degree of agglomeration in the composites. In comparison with materials generated from micelle-free solutions, the particle size distribution is narrow. The reverse micelle-mediated approach produces composites of high transparency comparable with that of pure PMMA. 相似文献
12.
13.
14.
15.
溶胶-凝胶法合成聚甲基丙烯酸甲酯/二氧化钛杂化聚合物材料 总被引:7,自引:0,他引:7
由共聚合在PMMA聚合物链段上引入了-Si(OR)3功能团,通过溶胶-凝胶过程合成了PMMA/TiO2杂化聚合物材料.溶剂抽提结果表明有化学键存在的杂化材料体系中凝胶的含量很高.通过FTIR测试对材料结构进行了分析,由TGA、DSC测试分析了杂化材料体系中无机组份的含量对材料性能的影响. 相似文献
16.
Tan KT Vogt BD White CC Steffens KL Goldman J Satija SK Clerici C Hunston DL 《Langmuir : the ACS journal of surfaces and colloids》2008,24(17):9189-9193
The origins for abrupt adhesion loss at a critical relative humidity (RH) for polymeric adhesives bonded to inorganic surfaces have been explored using a model poly(methyl methacrylate) (PMMA) film on glass. The interfacial and bulk water concentrations within the polymer film as a function of D 2O partial pressure were quantified using neutron reflectivity. Adhesion strength of these PMMA/SiO 2 interfaces under the same conditions was quantified using a shaft loaded blister test. A drop in adhesion strength was observed at a critical RH, and at this same RH, a discontinuity in the bulk moisture concentration occurred. The moisture concentration near the interface was higher than that in the bulk PMMA, and at the critical RH, the breadth of the interfacial water concentration distribution as a function of distance from the SiO 2/PMMA interface increased dramatically. We propose a mechanism for loss of adhesion at a critical RH based upon the interplay between bulk swelling induced stress and weakening of the interfacial bond by moisture accumulation at the PMMA/SiO 2 interface. 相似文献
17.
以多壁碳纳米管(MWCNTs)为导电填料、疏水纳米二氧化硅(SiO2)为非导电填料,填充不相容聚甲基丙烯酸甲酯(PMMA)/聚苯乙烯(PS)(1/1,V/V)共混物,制备(PMMA/SiO2)/(PS/MWCNTs)四元导电高分子复合材料(CPC),研究其导电逾渗与动态流变行为,并与PMMA/(PS/MWCNTs)三元CPC进行对比.发现三元、四元CPC具有类似的导电逾渗行为,且逾渗阈值显著低于PS/MWCNTs二元CPC.在四元CPC中,SiO2粒子可细化相区尺寸,提高熔体模量,但不影响熔体热处理过程中的依时性动态导电逾渗行为.MWCNTs与SiO2均显著影响熔体热处理中的依时性模量逾渗行为,分别缩短、延长四元CPC相粗化起始时间,但均延长相粗化时间区间. 相似文献
18.
溶胶-凝胶法合成聚(甲基丙烯酸乙酯-甲基丙烯酸环氧丙酯)/SiO_2杂化聚合物材料 总被引:11,自引:0,他引:11
通过溶胶 凝胶过程合成了一系列存在相间偶联键的杂化聚合物材料 .IR分析证实了在无机组份与有机组份间存在碳氮键 ,其特征吸收峰在 1 2 5 0cm-1.DSC的测试结果则表明无机组份含量的增加提高了材料的Tg 值 ,从而提高了杂化材料的使用温度 .利用小角X ray散射 (SAXS)和电镜 (TEM)分析了不同无机组份、不同酸度下体系的形态结构 ,结果表明当无机组份与有机组份的摩尔比为 1∶1且体系的酸度适当时相容性最好 . 相似文献